FEATURES
•
•
•
•
•
•
•
Compact design
User replaceable crossfader
2 phono, 2 line, 1 microphone input
Gain, Treble, and Bass Controls on Channels
Powerful stereo headphone output
Cue Pan Selector (Ch.1-Ch.2)
Bright LED Output Indicators
MIXER FEATURES
6
4
11
10
9
2
3
1
5
7
8
MIC
MIXER FEATURES
1. Input fader - Controls individual source levels (channels) in the mix.
2. Input toggle switch - Selects which source will be active based on what you have connected to the
rear panel input section (phono/line).
3. Treble and Bass EQ - Adjusts the high and low frequency levels of the input channels for good
sound.
4. Channel Gain - Adjusts the pre-fader volume for cleaner sound.
5. Replaceable Crossfader - Achieves clean fades between the two input channels. "Hard left"
selects Channel 1. "Hard right" selects Channel 2. With the crossfader centered, both assigned
channels are live. Use the crossfader for fast and seamless (fades) from one selected
channel to the other.
Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large screws
which hold it in place, lift it out and disconnect it ís cable. Re-attach the new crossfader and screw
the mounting plate back onto the unit - you're back in business!
6. Mic Input Gain - Adjusts microphone input level.
7. Mic Input - Insert your Microphone with 1/4" plug in here.
8. Headphone Input - Insert in the 1/4" plug for your headphones here.
9. Channel Cue / Cue Pan - Used to preview channel audio to your headphones. Listen here before
bringing up channel faders or moving the crossfader.
10.Headphone Level - Adjusts cue volume.
11.Master Fader - Controls the overall output level.
REAR PANEL
16
15 14 13
12
17
12.Ground - Grounding post for turntable connection. Always use this connection when using standard
turntables with ground cable. (Some turntables like the STR8-80 /100 do not require grounding wire)
13.Phono Inputs - Plug your turntables in here. W hen these connectors are used, your signal is fed
directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line
level sources will overload the sensitive phono pre-amps and will cause distortion.
14.Line Inputs - Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD
players, HiFi VCRs, cassette and reel-to-reel tape decks, DAT machines, laser discs, tuners, even
synthesizers or other mixing consoles.
NOTE: Plug mono audio sources into both Left and Right inputs using a "Y" cable connector.
15.Stereo Main Outputs - Unbalanced RCA connectors controlled by the Master fader.
16.Power Connector - Plug in power adapter here and check the voltage level to match your country ís
standard.
17.Power Switch - turns unit off and on. Note*** Remember to turn ALL volume levels down when
turning on/off the unit.
QUICK SETUP DIAGRAM
Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all
input sources and processors. Next, connect your microphone and monitor headphones. Finally,
connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug
your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on
your audio input sources such as turntables or CD players first, then your mixer, and finally any
amplifiers. When turning off, always reverse this operation by turning off amplifiers, then your mixer,
and then input devices.
TURNTABLE
TURNTABLE
POWER
SUPPLY
CD PLAYER
SOUND SYSTEM
TAPE DECK
SPECIFICATIONS
SENSITIVITY OF INPUT (LEVEL/IMPEDANCE):
LINE -14dB/47K OHM ±3dB
PHONO -50dB /47K OHM ±3dB
MIC -54dB /6K OHM ±3dB
OUTPUT (LEVEL/IMPEDANCE):
MASTER (RCA) 0dB/47K OHM
±3dB
PHONES (LOAD=32 OHM)
-3dB/33 OHM
±3dB
MAX. OUTPUT (LOAD=47K, THD=5%)
MASTER (RCA)
MORE THAN 18dB (8V)
PHONES (LOAD=32 OHM)
MORE THAN 5dB (1.8V)
CHANNEL BALANCE
WITHIN 3dB
FREQUENCY RESPONSE:
LINE 20-20KHz ±3dB
20-20KHz
PHONO
MIC 50-20KHz
+2 / -3dB (RIAA)
+2 / -3dB
OUTPUT NOISE (IEC-A WEIGHTED)
LINE LESS THAN -75dB
PHONO
LESS THAN -65dB
MIC LESS THAN -55dB
TOTAL HARMONIC DISTORTION:
MASTER OUTPUT (LOAD=47K OHM) LESS THAN 0.2%
PHONES OUT (LOAD=32 OHM) LESS THAN 0.3%
CROSSTALK
MORE THAN 50dB AT 1KHz BETWEEN L AND R CHANNEL.
EQUALIZER:
LINE
LOW +9 / -25dB +2 / -3dB AT 100Hz
HI
+9 / -25dB +2 / -3dB AT 10KHz
MIC EQ
LOW +10/-10dB +2 / -3dB AT 100Hz
HI
+10/-10dB +2 / -3dBAT 10KHz
POWER SOURCE
DIMENSIONS
AC 9V
228 (W) X 265 (D) X 87 (H) mm
WEIGHT
2.8Kgs
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement
WARRANTY
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the
date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and
Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
RETURNS
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and
follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation
from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
c u t a l o n g d o t t e d l i n e
PLACE
STAMP
HERE
Stanton Magnetics, Inc.
3000 SW 42nd Street
Hollywood, FL 33312
U.S.A.
|