HANDVAC
Model SBH-200
______________________________________________________________________________________
In a continuous effort to improve our products, we reserve the right to change components and materials without notice.
_______________________________________________________________________________________
TABLE of CONTENTS
Important Safety Instructions ____________________________________ 2
Exploded View for Model SBH-200 _______________________________ 4
Assembling Your Vacuum_______________________________________ 5
Operating Instructions__________________________________________ 6
Changing and Cleaning the Dust Cup Filter ________________________ 6
Troubleshooting Guide _________________________________________ 7
Service for your Vacuum________________________________________ 7
Warranty Information___________________________________________ 8
LISTED
Sunbeam genuine parts and service: 1-866-933-0427
- 3 -
The suction hole (1) must be open and free of obstructions at
all times. Otherwise, the motor will overheat and could get
damaged.
CAUTION
EXPLODED VIEW
3
4
2
1
5
6
8
7
9
10
1. Suction Hole
6. Dust Cup Filter
7. Furniture Brush
8. Crevice Tool
2. Dust Cup Release Button
3. Power Switch
4. Handle
9. Power Cord
5. Dust Cup Container
10. Extension Hose
- 4 -
aWARNINGa
Improper use of the power cord can result in the risk of electrical shock. If the
power cord is damaged, have it replaced by an authorized service center.
ASSEMBLING YOUR VACUUM
Check all the parts and identify them against the illustration.
¾ ASSEMBLING YOUR VACUUM CLEANER
Warning: Always unplug from electrical outlet before opening the Dust Cup (5).
Note: Dust Cup Filter (6) must be used when operating the handvac.
1. To open the Dust Cup (5), push Dust Cup Release Button (5) and pull out the Dust Cup (5).
Verify that the Dust Cup Filter (6) is inside then attach the Dust Cup (5) to the handvac.
2. To attach the Furniture Brush (7) or Crevice Tool (8) to the handvac, push brush into the Suction Hole (1), as
shown below.
3. To use the Extension Hose (10), push the end of the hose into the Suction Hole (1) to use independently, or
you may attach the desired brush (7 or 8) to the other end of the Extension Hose (10), as shown below.
- 5 -
OPERATING INSTRUCTIONS
¾ TO OPERATE
Hold the handvac firmly with your hand on the Handle (4).
¾ TURNING VACUUM ON
Push the I/O Power Switch (3) to “I” position.
The Hand Vacuum is a very powerful machine. Make sure
CAUTION
that you hold it firmly; otherwise it can slip out of your grasp
and cause injury.
CHANGING & CLEANING THE DUST CUP FILTER
Warning: Always unplug from electrical outlet before opening the Dust Cup (5).
Reminder: It is better to wash the filter after using handvac.
1. To open the Dust Cup (5), push Dust Cup Release Button (2) and pull out the Dust Cup (5) (fig. 1).
2. Pull out the Dust Cup Filter (6) (fig. 2).
3. Empty the dust from the Dust Cup Filter (6).
4. Rinse the Dust Cup Filter (6) in cold water, and then wait until it completely dries before replacing it into
the Dust Cup (5) (fig. 3).
5. Place the Dust Cup Filter (6) carefully into the Dust Cup (5) (fig. 4).
6. Attach the Dust Cup (5) to the handvac.
fig.1
fig.2
fig.3
fig.4
- 6 -
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
1. Power Cord not firmly
plugged into outlet.
2. No power in wall outlet.
1. Plug unit in firmly.
HAND VACUUM
WILL NOT
OPERATE
2. Check fuse or breaker.
3. Replace fuse/reset breaker.
4. Take it to the authorized dealer.
1. Empty dust cup filter (see page
6).
2. Turn unit off and unplug from
wall outlet. Remove Dust Cup
Filter and check for object(s) in
air duct and remove.
HAND VACUUM
WILL NOT PICK-UP
OR SUCTION
1. Dust Cup Filter is full.
2. Unit clogged.
3. Dust Cup Filter needs
cleaning.
POWER IS WEAK
3. Clean or replace Dust Cup Filter
(see page 6).
1. Dust Cup Filter is full.
2. Dust Cup Filter is not
installed correctly.
3. Puncture/hole in Dust
Cup Filter.
1. Empty Dust Cup Filter.
2. Review Dust Cup Filter
instruction (see page 6).
3. Replace dust Cup Filter
(see page 6)
DUST ESCAPING
FROM HAND
VACUUM
1. Remove hose and/or
brushes.
2. Remove obstruction from
hose.
3. Empty and clean Dust Cup
Filter.
HAND VACUUM
HOSE OR
BRUSHES WILL
NOT PICK-UP
1. Hose clogged.
2. Dust Cup Filter is full.
SERVICE FOR YOUR VACUUM
Your best source for service or to purchase additional accessories is the authorized dealer where you
purchased your handvac.
You may also order parts and accessories by writing or calling us, advising what you need, the model number
of your vacuum, your return address and phone number(s), and when you can be reached. Contact us at:
Sunbeam genuine parts and service: 1-866-933-0427
ORIGINS INTERNATIONAL LIMITED
3337 Kraft Avenue S.E.
Grand Rapids, MI 49512
- 7 -
Staple your sales receipt here. Proof of
original purchase date is needed to obtain
service under warranty.
YOUR PRODUCT WARRANTY
LIMITED WARRANTY
For one year from the date of purchase by the original owner, ORIGINS will, at its option, repair or replace any
part of the appliance, which proves to be defective in material or workmanship under normal use. During this
period, ORIGINS will provide all parts necessary to correct any such defect free of charge, as long as the
appliance has been operated in accordance with the written instructions in this manual. In rental or commercial
use, the warranty period is 90 days. All products requiring service must be brought/sent to an authorized service
center or to ORIGINS for repair.
_______________________________________________________________________________________
WHAT TO DO IF YOU HAVE PROBLEMS: Should your vacuum prove defective during the warranty
period, please return to the authorized dealer where the vacuum was purchased. ORIGINS will, at its option,
replace on an exchange basis the defective part(s), at no charge except inbound freight.
_______________________________________________________________________________________
WHAT IS NOT COVERED
This warranty covers only normal consumer use. This warranty does not cover bags, belts, lamps, agitator
brush, roller brushes, motor carbon brushes, filters and any third party parts, components or other parts added
to the vacuum cleaner after its shipment from ORIGINS. ORIGINS is not responsible for warranty service
should the vacuum cleaner’s label, logo, rating label or serial number be removed, or should the product fail to
be properly maintained or fail to function properly as a result of misuse, abuse, improper operation, neglect,
improper shipping, damage caused by disasters such as fire, flood, and lightening, improper electrical current,
commercial use, or service other than by an authorized servicer. Packaging and shipping cost incurred in
presenting your Sunbeam® vacuum product for warranty service are your responsibility. If a claimed defect
cannot be identified or reproduced in service, you will be held responsible for costs incurred.
THE WARRANTY PROVIDED ABOVE IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED
WARRANTIES INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF
IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE
LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY
STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. EXCEPT
AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER ORIGINS NOR ITS AFFILIATES SHALL BE
LIABLE FOR ANY LOSS, INCONVENIENCE OR DAMAGE INCLUDING DIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE VACUUM
PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY. IN
NO EVENT WILL ORIGINS's LIABILITY EXCEED THE PURCHASE PRICE OF THE VACUUM CLEANER.
Some jurisdictions do not allow limitations on how long an implied warranty lasts and some jurisdictions do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from jurisdiction to jurisdiction.
Sunbeam genuine parts and service: 1-866-933-0427
Sunbeam® is a registered trademark of Sunbeam Products, Inc. used under license. Distributed by
Origins International Limited, 3337 Kraft Avenue SE, Grand Rapids, MI 49512
- 8 -
|