Owner’s Manual
Model Numbers:
Date 09-07-01
TMC-200
MINI-CULTIVATOR
TMC-200
Supplier To The Outdoor Power Equipment Industry
ISM, Inc. • 1028 4th Street SW • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212
tanaka-usa.com
TMC-200, MINI-CULTIVATOR
Owner’s Manual
b. For shallow tilling, move the unit quickly over soil surface. (Fig. 7) For deeper tilling, hold the unit over
the same area with the gentle back and forth motion. (Fig. 8)
NOTE:
a. Working throttle position depends on your size of engine and tilling
depth but half way open is standard. If tines rotate too fast, the unit
is likely to hop.
b. Do not work in rocky area. If the tines jammed with rock or hard
soil, or tangled around with long grasses, shut off engine first, then
remove the obstruction. (Fig. 9)
c. Do not use the unit in water or rooted, vine area. (Fig. 10 & 11)
d. The tines are pre-assembled at factory, when reassembling them, be aware of their direction.
e. Do not touch the gear case with bare hand right after operation. It gets hot.
f. Supply proper amount of lithium-based grease, such as Shell Aluvania grease R2, Shell Aluvania EP
grease 2, Mobile-Mobilux EP2 or equivalent after every 25 hours of use. (Fig. 12)
g. When reassembling, be sure to use 40grams of molybdenum added lithium-based grease or Shell
Retinax AM or equivalent.
tanaka-usa.com
2
TMC-200, MINI-CULTIVATOR
Owner’s Manual
MAJOR PARTS
Illustration of brush cutter side may change according to you unit.
APPLICATIONS:
MODEL
TANAKA BRUSH CUTTER
TMC-200
(For spline end drive shaft)
TBC-
2211/2501/2510/270PF/PN/300/3010/4500/4501/220/220SS/240/250/265/300
AST-210/7000/7000S, SUM-321E/4001500
(QUM-221, after serial # G182721)
(SUM-318, after serial # M211775/SUM-328, after serial # J085451)
(SUM-422, after serial # N089844)
(TBC-321/355/355SDH, SUM-368, after serial N168643)
tanaka-usa.com
3
TMC-200, MINI-CULTIVATOR
Owner’s Manual
Ref.
Number
Ref.
Number
Parts Number
Description
Qty
Parts Number
Description
BOLT 6XI2
Qty
001
002
003
004
005
006
007
008
009
010
012
013
014
015
016
017
018
019
400-39907-20
ASP-100
LOCK PIN
2
2
6
6
2
2
2
2
3
2
1
1
1
1
1
1
1
1
024
990-21060-121
992-10060-012
990-21060-251
249-063OG-20
301-39909-20
318-39907-20
323-39907-20
992-10050-012
990-11050-101
990-21060-181
442-33671-20
445-39907-20
992-00060-011
992-10060-012
991-01060-011
441-39907-20
992-01050-011
992-10050-012
1
1
1
1
1
1
1
4
4
2
1
1
2
2
2
1
4
4
SNAP PIN 8
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
S.WASHER 6
990-21060-121
992-10060-012
820-39907-20
310-39907-20
307-39907-20
999-66152-863
993-51028-002
999-61690-200
304-39907-20
120-32201-20
322-39907-20
999-61600-101
002-33130-20
999-62122-669
999-62122-668
321-39907-20
BOLT 6X 12
BOLT 6X25
S.WASHER 6
SPACER
CUTTER
GEAR WHEEL
GEAR CASE GASKET
GEAR CASE COVER
S.WASHER 5
CUTTER HOLDER
PROTECTION COVER
OIL SEAL 15286
STOP RING 0-28, INNER
BALL BEARING 6902,28MM/OD
DRIVE SHAFT
SCREW 5XlO
BOLT 6X 18
COVER BRACKET, 26 DIA.
SAFETY COVER HOLDER
SMALL WASHER 6
S.WASHER 6
WOOD-RUFF KEY 5X22X7XI4
GEAR CASE CAP
BALL BEARING 60OIZZ, 28MM/0
WORM SHAFT
NUT 6
THRUST WASHER 1226
THRUST NEEDLE BRG 2X4.5
STEP WASHER
SAFETY COVER
WASHER5
S.WASHER 5
BALL BEARING 6901ZZ,
24MM/OD
020
999-61690-101
1
042
990-11050-141
SCREW 5XI4
4
021
022
023
990-21060-121
727-01040-20
300-39909-20
BOLT 6XI2
1
2
1
043
044
045
906-39909-20
348-33130-20
294-39909-20
NAME PLATE, TMC200
COLLAR B
1
1
1
DRAIN GASKET
GEAR CASE
COLLAR
tanaka-usa.com
4
|