iQ SERIES
PERFORMANCE DATA AND HARDWARE INFO
iQ 10/15
Dimensions
540.0
680.0
1116.0
SECUR ET – VEB Eyebolt
The Tannoy iQ 10/15 loudspeaker can be flown
with high quality VEB M10 eyebolts with collar to
BS4278:1984. The loudspeakers are equipped
with internal steel braces, which also double as
the flying points, and accept VEB M10 eyebolts.
To install the VEB M10 eyebolts remove the
original M10 counter sunk screws from the
locations you wish to install the VEB M10
eyebolts. Then replace these counter sunk M10
screws with the VEB M10 eyebolts. The kelping
brackets on the rear of the cabinet should only
be used for tilting the loudspeaker to the desired
angle.
Important: It is imperative for safety reasons
that two eyebolts linked to two independently
fixed straps are used per cabinet.
Never attempt to use formed eyebolts i.e.
formed from a steel rod and bent into an eye.
SINGLE iQ SUSPENSION TRUSS (By ATM™)
The iQ suspension truss is an economical solution to suspending a single purpose
loudspeaker array from two or three fixed structural attachment points. The iQ Suspension
Truss is designed to hold the loudspeakers at the optimum splay angle to optimize cluster
performance. Most Suspension Trusses are equipped with two suspension rails with multiple
attachment holes that travel from front to back across the top of the array, allowing
manipulation of the center of gravity of the cluster to achieve down tilt without a pull strap.
Features:
•
•
•
•
•
Optimized fixed splay angle
Adjustable tilt
Fast multiple enclosure rigging system
Economical
Low profile, clean looking array
iQ Suspension Truss
The iQ Suspension Truss is a "semi-custom" product line that is built to order. Please contact
your Tannoy or ATM Fly-Ware dealer with the loudspeaker model numbers along with the
array application.
Full assembly instructions for the iQ Suspension Truss accompany the product.
Typical Suspension Truss applications –
2 x iQ 10/15
2 x iQ 10C & 2 x iQ 10/15
Performance Data
FREQUENCY RESPONSE
Anechoic System Frequency Response, 1 watt (MF/HF) @ 1 metre on axis
INPUT IMPEDANCE
Impedance (Passive MF/HF only)
High Frequency (Tri-amp option)
Anechoic Frequency Response, 1 watt (HF) @ 1 metre on axis
Impedance (HF only)
Mid Frequency (Tri-amp option)
Anechoic Frequency Response, 1 watt (MF) @ 1 metre on axis
Impedance (MF only)
A comprehensive range of measurements including off axis frequency response curves, oc
octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Ease™ data can be
downloaded from http://www.tannoy.com/
Technical Specifications
Frequency Response (1) +/- 3dB
-10dB Point
49Hz - 19kHz
43Hz
Nominal Dispersion
Driver Compliment
60o x 40 o (H x V)
MF/HF – 1 x 250mm (10”) PowerDual™
LF -
1 x 380mm (15”)
Configurations
Bi-amp (standard) - LF & Passive MF/HF
Tri-amp (optional)
Components
LF
Midrange
High Frequency
Frequency Band (3)
Sensitivity (1)
43Hz – 180Hz
101dB
180Hz – 2.77kHz
107dB
2.77kHz – 19kHz
110dB
Power Handling (2)
400W (average)
175W (average)
50W (average)
800W (programme) 350W (programme) 100W (programme)
1600W (Peak)
700W (peak)
200W (peak)
Impedance
8Ω
16Ω
16Ω
Maximum SPL (3)
127dB (average)
133 (peak)
129dB (average)
135dB (peak)
127dB (average)
133dB (peak)
DI Averaged (PCQ)
@ 1kHz (ISO)
@ 2kHz (ISO)
@ 4kHz (ISO)
@ 8kHz (ISO)
@ 16kHz (ISO)
11.0, 500 Hz - 16 kHz
12.6
12.2
9.5
11.5
12.3
Q Averaged (PCQ)
@ 1kHz (ISO)
@ 2kHz (ISO)
@ 4kHz (ISO)
@ 8kHz (ISO)
@ 16kHz (ISO)
13.5, 500 Hz - 16 kHz
18.3
16.7
8.8
14
16.9
Crossover
Active 180Hz, Passive 2.6kHz (standard model)
4th order high pass, 4th order low pass
Enclosure
Finish
18mm multi-ply birch plywood
Textured black paint (optional in white)
Foam covered, powder coated perforated steel
Protective Grille
Connectors
2 x Speakon NL4MP in/out (standard model)
4 x Speakon NL4MP (optional tri-amp model)
Fittings
8 x M10 inserts & 2 pullback points
4 x Recessed Carrying handles
Dimensions
Weight
1116mm x 680mm x 540mm
(43 15/16” x 26 ¾” x 21 ¼”)
69kg (152.1 lbs)
NOTES:
(1) Average over stated bandwidth. Measured at 1m on axis.
(2) Long term power handling capacity as defined in EIA standard RS - 426A.
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber
The iQ 10/15 is designed for use with the Tannoy TDX1 & TDX2 digital system controller, which provide a preset configuration of
Crossover frequencies, relative output levels, and system equalization for optimum performance. Should you intend using an alternative
Loudspeaker management system, these parameters can be accessed from the Tannoy website – www.tannoy.com - or can be found in this
IQ 10/15 user manual.
Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the publish
which Tannoy reserves the right to alter without prior notice.
Please verify the latest specifications when dealing with critical applications.
Unique Funktion One Axhead Technology (UK patent number GB2270606) is incorporated into
Tannoy iQ Series SuperDualTM products by agreement with Funkton One Research
iQ 10/15 Service Parts and Accessories
Part Number Description
7900 0607
7900 0609
7900 0608
7900 0610
Driver Kit Type 2519 (MF)
Recone Kit Type 2519 (MF)
Driver Kit Type 0278 (HF)
Diaphragm Type 0278 (HF)
8001 2820
VEB – Secur ET – Eyebolts M10
8000 3630
8000 3631
8000 3632
TDX1 Digital System Controller 60-250V – UK
TDX1 Digital System Controller 60-250V – EUR
TDX1 Digital System Controller 60-250V – USA
8000 0727
8000 0728
8000 0729
TDX2 Digital loudspeaker management system 60-250V - UK
TDX2 Digital loudspeaker management system 60-250V - EUR
TDX2 Digital loudspeaker management system 60-250V – USA
Warranty
No maintenance of the iQ 10/15 loudspeaker is necessary.
All Tannoy professional loudspeaker products are covered by a 5 year warranty from
the date of manufacture subject to the absence of misuse, overload or accidental
damage. Claims will not be considered is the serial number has been altered or
removed. A Tannoy Professional dealer or service agent should only carry out work
under warranty. This warranty in no way affects your statutory rights. For further
information, please contact your dealer or distributor in your country. If you cannot
locate your distributor, please contact Customer Services, Tannoy Ltd at the address
given below.
Customer Services
Tannoy Ltd.
Coatbridge
ML5 4TF
Scotland
Telephone:
Fax:
01236 420199
+44 1236 420199
01236 428230
(National)
(International)
(National)
+44 1236 428230
(International)
E-Mail:
Website:
DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION
Our policy commits us to incorporating improvements to our products through
continuous research and development. Please confirm current specifications for
critical applications with your supplier.
Declaration of Conformity
The following apparatus is/are manufactured in the United Kingdom
by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland,
ML5 4TF and conform(s) to the protection requirements of the
European Electromagnetic Compatibility Standards and Directives
relevant to Domestic Electrical Equipment. The apparatus is
designed and constructed such that electromagnetic disturbances
generated do not exceed levels allowing radio and
telecommunications equipment and other apparatus to operate as
intended, and, the apparatus has an adequate level of intrinsic
immunity to electromagnetic disturbance to enable operation as
specified and intended. This Equipment conforms to the
requirements of the EMC Directive 89/336/EEC, amended by
92/31/EEC and 93/68/EEC and the requirements of the low voltage
directive 73/23/EEC, amended by 93/68/EEC.
Details of the Apparatus:
Tannoy Contractor Loudspeaker
Model Number: iQ10/15
Associated Technical File:
Applicable Standards:
EMCIQ10/15
EN 55103 –1:1996 Emission
EN 55103 –2:1996 Immunity
EN 60065:1993
Electrical Safety:
Signed:
Position:
Engineering Director – Professional Products
Tannoy Professional
Date:
11/10/2004
For Tannoy Ltd
|