OPERATING INSTRUCTIONS
SPEAKER SYSTEMS
F-2000B
F-2000BT
F-2000W
F-2000WT
F-2000BTWP F-2000WTWP
Thank you for purchasing TOA's Speaker System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
533-06-146-20
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
• Do not use anti-rust lubricant. If it contacts resin or
rubber parts, they could deteriorate and cause the
unit to fall, possibly resulting in personal injury.
WARNING
Indicates a potentially hazardous situation which,
• Avoid installing the speaker in locations close to
if mishandled, could result in death or serious
the seashore or in indoor swimming facilities that
personal injury.
are not well ventilated. In such locations the
bracket may be vulnerable to corrosion, eventually
When Installing the Unit
allowing the speaker to fall resulting in personal
injury.
• Install the unit only in a location that can
structurally support the weight of the unit and the
mounting bracket. Doing otherwise may result in
the unit falling down and causing personal injury
and/or property damage.
CAUTION
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury, and/or property damage.
• Do not use other methods than specified to mount
the bracket. Extreme force is applied to the unit
and the unit could fall off, possibly resulting in
personal injuries.
When Installing the Unit
• Use nuts and bolts that are appropriate for the
ceiling's or wall's structure and composition. Failure
to do so may cause the speaker to fall, resulting in
material damage and possible personal injury.
• Avoid touching the unit's sharp metal edge to
prevent injury.
• To avoid electric shocks, be sure to switch off the
unit's power when connecting speakers.
• Tighten each nut and bolt securely. Ensure that the
bracket has no loose joints after installation to
prevent accidents that could result in personal
injury.
When the Unit is in Use
• Do not place heavy objects on the unit as this may
cause it to fall or break which may result in
personal injury and/or property damage. In
addition, the object itself may fall off and cause
injury and/or damage.
• Do not mount the unit in locations exposed to
constant vibration. The mounting bracket can be
damaged by excessive vibration, potentially
causing the unit to fall, which could result in
personal injury.
• Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in a fire.
• (F-2000B, F-2000BT, F-2000W, F-2000WT only)
Since the unit is designed for in-door use, do not
install it outdoors. If installed outdoors, the aging of
parts causes the unit to fall off, resulting in personal
injury. Also, when it gets wet with rain, there is a
danger of electric shock.
• Do not stand or sit on, nor hang down from the unit
as this may cause it to fall down or drop, resulting
in personal injury and/or property damage.
• (F-2000BTWP, F-2000WTWP only)
• Have the unit checked periodically by the shop
from where it was purchased. Failure to do so may
result in corrosion or damage to the unit or its
mounting bracket that could cause the unit to fall,
possibly causing personal injury.
When installing the unit in the snowy area, take
appropriate measures to prevent snow from lying
on the unit. If the snow lies on the unit, the unit may
fall, causing personal injuries.
3
2. GENERAL DESCRIPTION
TOA's F-2000 Series Speakers are compact two-way speaker systems designed for high efficiency, wide
range, and high power input handling capability. These speaker systems can be installed in a manner ideal for
the location and intended application.
3. FEATURES
• 100º horizontal x 100º vertical wide directivity high-frequency horn.
• Coverage angle can be changed to 80º horizontal x 80º vertical by attaching the supplied horn adapter.
• Supplied bracket permits mounting to a wall, ceiling, or an optional speaker stand.
• Combined use of the supplied bracket and optional mounting bracket allows the speakers to be mounted in
many different applications, including pole mounting,*1 clusters and horizontal ceiling mounting*2.
• Both the F-2000BTWP and F-2000WTWP feature a waterproof design (IPX4 standard) for protection from
any adverse effects of outdoor installations.
*1 Applies to the F-2000BTWP and F-2000WTWP.
*2 Applies to the F-2000B, F-2000BT, F-2000W, and F-2000WT.
4. DIMENSIONAL DIAGRAM
Unit: mm
[Top]
[Bottom]
Mounting holes
Note
Hole seals are adhered over the holes at the factory.
Before attaching the speaker mounting bracket to this
side, remove them using a pointed tool.
6-M5 mounting screw hole
(Effective screw depth: 14 mm)
[Front]
[Side]
[Rear]
235
15º
50
244
2-M5 mounting screw hole
(Effective screw depth: 14 mm)
4
5. IMPEDANCE CHANGE (F-2000BT, F-2000BTWP, F-2000WT, and F-2000WTWP only)
To change the impedance, use a standard screwdriver to rotate the rotary switch on the speaker's rear to
select the desired input power.
Note: The switch is factory-preset to 170 Ÿ.
Important
Never set this switch to the "83 Ÿ" position when operating the speaker on 100 V line.
Failure to follow this instruction could result in damage to the speaker or amplifier.
6. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY
(F-2000B and F-2000W only)
The speaker system features internal input overload protection circuitry for both high and low frequencies.
If an excessive input level is fed to the unit, the protection circuitry automatically cuts off the signal to the
speaker driver.
A drastic reduction in sound volume for the high or low frequency range indicates that the protection circuitry
has been enabled.
In such cases, simply reduce the amplifier volume. The protection circuitry will automatically reset in
approximately 10 seconds. After reset, maintain the volume at a level slightly lower than before.
Note
This protection circuitry does not completely protect the unit against input overload. Depending on the type or
duration of excessive power input, the protection circuitry might not be enabled, resulting in damage to the
speaker driver. Also, if the excessive power input continues for a long period of time, the circuitry may not be
capable of resetting to its original condition.
Take care so that the speakers are not exposed to excessive power input.
5
7. NOTES ON OUTDOOR INSTALLATION (F-2000BTWP and F-2000WTWP only)
• Be sure to mount the speaker in a vertical (portrait-style) orientation.
• Adjust the speaker's tilt angle within the shaded range shown below:
[Wall and pole: 0º horizontal to 45º downward]
[Under eaves: 15º downward to 45º downward]
Note
Mount the speaker so that its rear-mounted terminal
cover is positioned on the upper side.
Note
The speaker faces 15°
downward when mounting
to a horizontal surface.
15°
0°
(horizontal)
0º
(horizontal)
(30°)
45°
45°
• Install the speaker in locations exposed to an ambient temperature range of –10ºC to +50ºC. Exceeding this
range could cause speaker failure.
• Use the supplied terminal cover when connecting the speaker cable.
[Terminal Cover Use]
Input terminal
2
Terminal cover (accessory)
3
Tapping screw 4 x 12 (accessory)
4
Bushing*
1
[Stripped conductor]
Speaker cable
10 mm
30 mm
Speaker unit
* Screwed onto the Terminal cover at the factory.
Notes
• For the speaker cable, use a cable with a diameter of 6 – 10 mm, which will fit the cable bushing.
• To ensure waterproof capabilities, firmly mount the terminal cover to the speaker and tighten the bushing on
the cover.
Step 1. Feed the speaker cable through the bushing and terminal cover, then connect the cable to the input
terminal.
Step 2. Attach the terminal cover to the speaker.
Attach the cover while pulling the cable so that it is not entangled inside the terminal cover.
Step 3. Hold the terminal cover tightly to the speaker using the supplied screws.
Step 4. Tighten the bushing.
Note
After tightening the bushing by hand, use a tool to further tighten it another 90º (1/4-turn) or so. Note
that parts can be damaged by over-tightening.
6
8. INSTALLATION
8.1. Using the Supplied Brackets
The speaker system is supplied with the following brackets. Use these brackets properly depending on the
installation location and intended application.
[Speaker bracket]
[Joint bracket]
[Wall bracket]
30º
8.1.1. When using only the supplied brackets
Installation
Application
Location
Speaker bracket Joint bracket Wall bracket Page
P. 8
When horizontal and vertical
angle adjustability is desired.
Wall
When close wall surface
mounting is desired*.
P. 9
P. 10
P. 12
Ceiling
Vertical speaker mounting*
Speaker Stand Mounting to the optional
(Option) ST-16A Speaker Stand
* Speaker coverage angles can only be adjusted in the vertical direction.
8.1.2. When using both the supplied and optional mounting brackets
Installation
Location
Application
Option
Speaker bracket Joint bracket
Wall bracket Page
P. 11
Horizontal speaker HY-CM20B or
mounting
HY-CM20W
HY-CL20B
Ceiling
Suspended speaker
cluster mounting*
P. 11
P. 13
SP-131 and
YS-60B
Pole
Mounting to a pole
* Speaker coverage angles can only be adjusted in the vertical direction.
8.2. Speaker Cable Connections
[Input terminal polarity]
[Stripped conductor of cable]
Sperker unit (rear)
10 mm
Input terminal
(–)
(+)
BLACK RED
7
8.3. Wall Mounting
When adjusting horizontal and vertical angles:
Use the supplied wall bracket, joint bracket, and speaker bracket to permit adjustment of the horizontal and
vertical* speaker coverage angles.
* Vertical installation.
Horizontal: Max. 70º, Vertical: Max. 45º downward
Horizontal installation. Horizontal: Max. 45º, Vertical: Max. 45º downward
[Wall bracket mounting dimensions]
[Installation example]
4-ø6 mm
Vertical speaker
mounting
2
Hexagon bolt M6 x 12
(with plain washer
45 mm
and spring washer)
Wall bracket
Joint bracket
1
Horizontal speaker
mounting (indoor
installation only)
4
6
Fixing bolt M6 x 85
[Vertical speaker installation]
[Horizontal speaker installation]
3
Speaker bracket
Speaker bracket
Speaker unit
Machine screw
Machine screw
M5 x 20 (with plain
washer and spring
washer)
M5 x 20 (with plain
washer and spring
washer)
Speaker unit (rear)
Speaker unit (rear)
Step 1. Mount the wall bracket to the wall surface.
Match the orientation of the arrow label with the horizontal direction (left or right) the speaker faces.
Note: Hardware used for mounting the wall bracket to the wall is not supplied.
• Arrow label orientation (Viewed from top of brackets)
[Right-facing orientation]
[Left-facing orientation]
Wall bracket
Wall bracket
Arrow label
Arrow label
Joint bracket
Joint bracket
8
Step 2. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker
angle, then tighten the screws.
Note: Match the orientation of the arrows on both the wall bracket and joint bracket.
Step 3. Attach the speaker bracket to the speaker's rear using the supplied screws.
Note: Attach the speaker bracket according to the speaker mounting orientation.
Step 4. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and
loosely securing the fixing bolt for temporary speaker installation.
Step 5. Connect the speaker cable to the input terminal.
Note
Use a terminal cover when installing the speaker outdoors. (Refer to p.6 for terminal cover
attachment.)
Step 6. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.
The speaker angle is adjustable in 7.5º steps.
Note
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that
both parts are securely engaged with each other after mounting is complete.
[Changing the orientation of the front panel logo]
The front panel logo is affixed to the mesh net using double-faced tape. Peel off the logo carefully and reaffix it
in the proper orientation.
Mounting the speaker close to a wall surface
Use both the supplied joint bracket and speaker bracket, and mount the joint bracket directly to a wall. After
mounting the joint bracket, follow the Steps 3 – 6 above. In this configuration, the speaker can only be
adjusted in the vertical direction*.
* Vertical installation: Max. 37.5º downward, Horizontal installation: Max. 45º downward
Note: Hardware used for mounting the joint bracket to the wall is not supplied.
[Installation example]
[Joint bracket mounting dimensions]
4-ø6 mm
Joint bracket
Vertical speaker
mounting
45 mm
6
4
Horizontal speaker
mounting (indoor
installation only)
Fixing bolt
M6 x 85
Speaker bracket
Speaker unit
9
8.4. Ceiling Mounting
Vertical orientation
Use the supplied joint bracket and speaker bracket.
Note
Speaker coverage angles can only be adjusted in the vertical direction (Max. 45º downward).
Adjust the speaker's tilt angle within the shaded range shown below:
[Speaker angle vs. Bracket position]
[Installation example]
a
0º (horizontal)
45º downward
b
Joint bracket
a
0°
(horizontal)
Speaker
bracket
45º
b
30º
15º
Notes
1
• Use an appropriate anchor bolt for supporting
the full weight of the speaker and for the size
of mounting hole in the joint bracket.
Anchor bolt mounting hole
Joint bracket
• Ensure that the effective length of the anchor
bolt is 25 mm or less.
• When speaker rotation capability is not desired,
secure with the 4 fixed mounting screw holes.
Fixed mounting screw hole
(4 holes)
Fixing bolt M6 x 85
2
Anchor bolt
Ceiling board
5
Machine screw
3
M5 x 20 (with
plain washer and
spring washer)
Speaker bracket
Effective length
A s h o l e s e a l s a r e
Joint bracket
adhered over the holes,
remove them using a
pointed tool before
attaching the bracket.
* Changing the orientation of the front panel logo
The front panel logo is affixed to the mesh net using
double-faced tape. Peel off the logo carefully and
reaffix it in the proper orientation.
Speaker unit
Front panel logo*
Step 1. Mount the joint bracket to the ceiling surface.
[Joint bracket mounting dimensions]
Note
Hardware used for mounting the joint bracket to the ceiling is
not supplied.
4-ø6 mm
ø10 mm
Step 2. Attach the speaker bracket to the speaker's bottom using the
supplied screws.
45 mm
10
Step 3. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and
loosely securing the fixing bolt for temporary speaker installation.
Step 4. Connect the speaker cable to the input terminal.
Note
Use a terminal cover when installing the speaker outdoors. (Refer to p. 6 for terminal cover
attachment.)
Step 5. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.
The speaker angle is adjustable in 7.5º steps.
Note
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that
both parts are securely engaged with each other after mounting is complete.
Horizontal orientation (F-2000B, F-2000BT, F-2000W, and F-2000WT only)
[Installation example]
Use the supplied joint bracket and speaker bracket in combination with
the optional HY-CM20B or HY-CM20W Ceiling Mount Bracket.
Refer to the instruction manual enclosed with the optional mounting
bracket for its mounting details.
Cluster configuration assembly
(F-2000B, F-2000BT, F-2000W, and F-2000WT only)
[Installation example]
Use the supplied joint brackets and speaker brackets in
combination with the optional HY-CL20B Cluster Bracket
to permit a total of 4 speakers to be suspended from the
ceiling as shown in the figure at right.
Refer to the instruction manual enclosed with the
optional mounting bracket for its mounting details.
11
8.5. Speaker Stand Mounting
The speaker can be mounted on the optional ST-16A Speaker Stand using the supplied joint bracket and
speaker bracket.
[Installation example]
Speaker unit
A s h o l e s e a l s a r e
adhered over the holes,
remove them using a
pointed tool before
attaching the bracket.
Machine screw
M5 x 20 (with
plain washer and
spring washer)
2
Max.180 cm
Speaker bracket
Butterfly nut
(supplied with
the ST-16A)
3
3
Washer
(supplied with
the ST-16A)
Fixing bolt M6 x 85
1
Joint bracket
Note
Bracket
(supplied with the ST-16A)
Mount the speaker so that it faces
within the range of 15º upward and
downward.
Hexagon bolt
(supplied with the ST-16A)
a
15°
15°
ST-16A (option)
b
Step 1. Attach the joint bracket to the speaker stand bracket using
the speaker stand's supplied bolt and nut.
Step 2. Attach the speaker bracket to the speaker's bottom using the
supplied screws.
[Speaker angle vs. Bracket position]
a
b
Step 3. Mount the speaker to the joint bracket by inserting the
speaker bracket into the joint bracket and loosely securing
the fixing bolt for temporary speaker installation.
After adjusting the speaker's vertical mounting angle, tighten
the fixing bolt.
15º upward
15º downward
0°
30°
The speaker angle is adjustable in 7.5º steps.
The mating surfaces of the speaker bracket and joint bracket
are designed to interlock. Ensure that both parts are
securely engaged with each other after mounting is
complete.
Speaker bracket
Joint bracket
Step 4. Connect the speaker cable to the input terminals.
Note
Use a terminal cover when installing the speaker outdoors.
(Refer to p. 6 for terminal cover attachment.)
Note
For more information on mounting the bracket to the stand and stand usage, refer to the instruction manual
enclosed with the ST-16A Speaker Stand.
12
8.6. Pole Mounting (F-2000BTWP and F-2000WTWP only)
To mount the speaker on a pole with diameter of 9 – 34 cm, use the
supplied wall bracket, joint bracket, and speaker bracket in combination
with the optional SP-131 Pole Mount Bracket and YS-60B Pole Band.
Speaker coverage angles can be adjusted in the horizontal and vertical
direction*.
[Installation example]
* Horizontal: Max. 90º, Vertical: Max. 45º downward
Note
Although the SP-131 comes in 2 sets of brackets, use one set only.
Plain washer for M8
(supplied with the SP-131)
Hexagon bolt M6 x 12
(with plain washer
and spring washer)
Plain washer for M8
(supplied with the SP-131)
3
Hexagon bolt M8 x 20
Spring washer for M8
(supplied with the SP-131)
(supplied with the SP-131)
Wall bracket
Nut for M8
(supplied with the SP-131)
YS-60B (option)
SP-131 (option)
Joint bracket
2
1
3
7
5
Fixing bolt M6 x 85
[Speaker bracket mounting position]
4
Speaker bracket
Note
Set the speaker in a vertical orientation,
then attach the bracket so that the rear-
mounted terminal cover is positioned
above the mount.
Speaker unit
Machine screw
M5 x 20 (with plain
washer and spring
washer)
Speaker (rear)
13
Step 1. Attach the wall bracket to the SP-131 Pole Mount Bracket.
Match the orientation of the arrow label with the horizontal direction (left or right) the speaker faces.
Use the bolts supplied with the SP-131.
• Arrow label orientation (Viewed from top of brackets)
[Right-facing orientation]
[Left-facing orientation]
Pole
Pole
SP-131
SP-131
Wall bracket
Wall bracket
Joint bracket
Arrow label
Arrow label
Joint bracket
Step 2. Attach the SP-131 to a pole using the YS-60B.
Step 3. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker
angle, then tighten the screws.
Note
Match the orientation of the arrows on both the wall bracket and joint bracket.
Step 4. Attach the speaker bracket to the speaker's rear using the supplied screws.
Note
Set the speaker in a vertical orientation, then attach the bracket so that the rear-mounted terminal
cover is positioned above the mount.
Step 5. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and
loosely securing the fixing bolt for temporary speaker installation.
Step 6. Connect the speaker cable to the input terminal.
Note
Use a terminal cover when installing the speaker outdoors. (Refer to p. 6 for terminal cover
attachment.)
Step 7. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.
The speaker angle is adjustable in 7.5º steps.
Note
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that
both parts are securely engaged with each other after mounting is complete.
14
9. REDUCING THE SPEAKER COVERAGE ANGLE
The speaker's coverage angle can be reduced to 80º horizontal x 80º vertical from its normal range of 110º x
110º by attaching the supplied horn adapter to the speaker's horn section.
[Without horn adapter]
[With horn adapter]
110º horizontal
80º horizontal
80° vertical
100° vertical
[Attaching the horn adapter]
Horn adapter
Note
2
Take care not to touch the
speaker diaphragm during
attachment.
Tapping screw 4 x 12
Mesh speaker grill
Countersunk head
tapping screw 4 x 12
1, 3
Logo
Note
Because the logo is affixed using double-faced tape, peel it off carefully.
Step 1. Peel off the logo carefully, then remove the screw underneath to detach the mesh speaker grill.
Step 2. Attach the supplied horn adapter using the supplied screws.
Step 3. Replace the mesh grill and logo.
15
10. REPAINTING THE SPEAKER
Follow the procedure below when repainting the speaker grill and cabinet.
Note
Take care not to touch the speaker diaphragm during work.
Step 1. Peel off the logo carefully, then remove the screw underneath to detach the mesh speaker grill.
[Detaching the mesh grill]
Mesh speaker grill
Countersunk head
tapping screw 4 x 12
Baffle (Masking area)
Logo
Note
Because the logo is affixed using double-faced tape, peel it off carefully.
Step 2. Wipe clean the mesh grill and speaker cabinet with a soft cloth dampened in a detergent.
Note
Do not use thinner or other volatile liquids to clean the grill and cabinet.
Step 3. Use spray paint to apply thin coat evenly overall the speaker.
Notes
• Avoid painting with a roller or brush, as the grill holes could become clogged with paint.
• Securely mask the entire baffle surface before painting.
• Use appropriate paints for the speaker grill and cabinet materials.
Grill: Rolled steel plate (acrylic paint)
Cabinet: Fire-resistant HIPS resin
Step 4. After the paint has dried, apply another light coat.
Note
Repeating Step 3, apply 2 or more light coats of paint.
Application of one thick coat of paint all at once may cause drips or unevenness to show up in the
painted finish, or clog the mesh holes.
Step 5. After the paint has dried, replace the mesh grill and logo.
16
11. SPECIFICATIONS
11.1. F-2000B and F-2000W
Model No.
F-2000B
F-2000W
Enclosure Type
Power Handling Capacity
Bass-reflex type
60 W (continuous pink noise)
180 W (continuous program)
8 Ÿ
Rated Impedance
Output Sound Pressure
Level
92 dB (1 W, 1 m) at installation in a semianechoic field
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)
65 – 20,000 Hz, –10 dB at installation in a semianechoic field
2.5 kHz
Frequency Response
Crossover Frequency
Directivity Angle
Horizontal: 110º, Vertical: 100º
Horizontal: 80º, Vertical: 80º (with horn adapter)
Woofer: 20 cm cone-type
Speakers
Tweeter: 25 mm dome-type
Input Terminals
Enclosure
Push-in terminals
HIPS, black
HIPS, white
Mesh Speaker Grill
Speaker Bracket
Joint Bracket, Wall Bracket
Dimensions
Surface-treated steel plate, black, paint
Aluminum die-cast, black, paint
Steel plate, t2.0, black, paint
Surface-treated steel plate, white, paint
Aluminum die-cast, white, paint
Steel plate, t2.0, white, paint
244 (w) x 373 (h) x 235 (d) mm
Weight
6.5 kg (including the supplied brackets)
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,
Tapping screw 4 x 12 ... 4, Horn adapter ... 1
Accessories
Optional Products
Ceiling mount bracket: HY-CM20B
Ceiling mount bracket: HY-CM20W
Cluster bracket:
Speaker stand:
HY-CL20B
ST-16A
Cluster bracket:
Speaker stand:
HY-CL20B
ST-16A
Note: The design and specifications are subject to change without notice for improvement.
17
11.2. F-2000BT and F-2000WT
Model No.
F-2000BT
F-2000WT
Enclosure Type
Bass-reflex type
60 W
Power Handling Capacity
Rated Impedance
170 Ÿ (60 W), 330 Ÿ (30 W), 670 Ÿ (15 W), 3.3 kŸ (3 W)
Output Sound Pressure
Level
92 dB (1 W, 1 m) at installation in a semianechoic field
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)
65 – 20,000 Hz, –10 dB at installation in a semianechoic field
2.5 kHz
Frequency Response
Crossover Frequency
Directivity Angle
Horizontal: 110º, Vertical: 100º
Horizontal: 80º, Vertical: 80º (with horn adapter)
Woofer: 20 cm cone-type
Speakers
Tweeter: 25 mm dome-type
Input Terminals
Enclosure
Push-in terminals
HIPS, black
HIPS, white
Mesh Speaker Grill
Speaker Bracket
Joint Bracket, Wall Bracket
Dimensions
Surface-treated steel plate, black, paint
Aluminum die-cast, black, paint
Steel plate, t2.0, black, paint
Surface-treated steel plate, white, paint
Aluminum die-cast, white, paint
Steel plate, t2.0, white, paint
244 (w) x 373 (h) x 235 (d) mm
Weight
7.4 kg (including the supplied brackets)
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,
Tapping screw 4 x 12 ... 4, Horn adapter ... 1
Accessories
Optional Products
Ceiling mount bracket: HY-CM20B
Ceiling mount bracket: HY-CM20W
Cluster bracket:
Speaker stand:
HY-CL20B
ST-16A
Cluster bracket:
Speaker stand:
HY-CL20B
ST-16A
Note: The design and specifications are subject to change without notice for improvement.
18
11.3. F-2000BTWP and F-2000WTWP
Model No.
F-2000BTWP
F-2000WTWP
Enclosure Type
Bass-reflex type
60 W
Power Handling Capacity
Rated Impedance
Output Sound Pressure
Level
170 Ÿ (60 W), 330 Ÿ (30 W), 670 Ÿ (15 W), 3.3 kŸ (3 W)
92 dB (1 W, 1 m) at installation in a semianechoic field
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)
65 – 20,000 Hz, –10 dB at installation in a semianechoic field
2.5 kHz
Frequency Response
Crossover Frequency
Directivity Angle
Horizontal: 110º, Vertical: 100º
Horizontal: 80º, Vertical: 80º (with horn adapter)
Woofer: 20 cm cone-type
Speakers
Tweeter: 25 mm dome-type
Input Terminals
Push-in terminals
Water Resistance
Operating Temperature
Enclosure
IPX4
–10 ºC to +50 ºC
HIPS, black
HIPS, white
Mesh Speaker Grill
Surface-treated steel plate, black,
anti-rust paint
Surface-treated steel plate, white,
anti-rust paint
Speaker Bracket
Joint Bracket, Wall Bracket
Dimensions
Aluminum die-cast, black, paint
Aluminum die-cast, white, paint
Stainless steel (SUS 304), t2.0
244 (w) x 373 (h) x 235 (d) mm
7.4 kg (including the supplied brackets)
Weight
Accessories
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,
Tapping screw 4 x 12 ... 8, Horn adapter ... 1, Terminal cover ... 1
Pole mount bracket: SP-131
Optional Products
Pole band:
YS-60B
Note: The design and specifications are subject to change without notice for improvement.
19
|