BT230 Bluetooth®
Headset User’s Guide
Also in this package:
AC (indoor) power adapter
2 extra ear cushions
or call our Customer Service line at 800-292-2294.
GeTTinG To Know THe HeadseT Ear
WARNING: Using the headset at excessive volume can
ON slide
LED
hook
Power
cause permanent hearing loss. To reduce
the risk of hearing damage, use the
minimum volume level necessary (see page
13).
Connector
Multi-
function
button
(
MFB)
Ear
cushion
* Specifications and features are subject to change
without notice.
VolumUep
Down
Microphone
what the Led Colors Mean
Color State
Meaning
The headset is currently charging. When the battery is fully
Steady
charged, the LED turns off.
Red
Flashing
If the headset is also beeping, the battery is low.
ꢀ
Color State
ꢀ flashes
Meaning
The headset is turned on.
1 flash every 5 seconds The headset is in standby & not paired to a Bluetooth device.
2 flashes every 5
The headset is currently paired to a Bluetooth device.
Blue
seconds
ꢀ flashes every 5
The headset is on an active call.
seconds
Red &
blue
Alternating flash
The headset is in pairing mode.
* Specifications and features are subject to change without notice.
what the Tones Mean
Tone
Meaning
Melody
Depending on the melody, the sound indicates one of the following:
- Power on
- Power off
- Incoming call
- Low battery
ꢁ
Tone
Meaning
2 Rising Beeps
2 Falling Beeps
ꢀ Short Beeps
Active call
Ending a Call
Successfully paired with a mobile phone
what the Buttons do
The headset initiates the function only after the button is released.
Press & hold it for
Press it to
2 seconds to
4 seconds to
Multifunction button (MFB)
In standby:
Put the
In standby: Redial the most recently
dialed number.
During an incoming call: Answer the call.
During a call: Hang up.
In standby: Activate voice dialing.
During an incoming call: Reject the call.
During a call: Transfer the call to your
phone (or back).
headset
into pairing
mode.
5
Press & hold it for
2 seconds to
Press it to
4 seconds to
Volume Up
During a call: Increase
the call volume.
During a call-waiting call: Put the active
call on hold and switch to the waiting call.
NA
NA
Volume Down
During a call: Decrease
the call volume.
NA
seTTinG Up YoUr HeadseT
Charge the Battery
► Before using your headset, charge the battery until the red LED turns off (about 2 hours).
Charging the battery completely (and keeping it charged) will help you get the longest possible
talk and standby time out of the battery.
► Connect the adapter to the power connector on the side of the headset, then plug it into any
standard 120 V AC (regular indoor) power outlet.
ꢂ
► When the battery needs to be recharged, you will hear warning beeps every ꢀ0 seconds and see
the red LED (depending on your headset status).
NOTE: Use ONLY the AC adapter supplied with the headset. Using any other adapter could
damage your headset, create a fire hazard, or cause a risk of electric shock!
pair the Headset to Your Bluetooth phone
Pairing is like “introducing”two Bluetooth devices and giving them permission to connect
to each other. If you want to use the headset with more than one phone, you need to pair
it with each phone separately. Once you pair a phone to the headset, the two devices can
connect automatically whenever they can detect each other.
NOTE: The headset automatically goes into pairing mode when it is used for the first time.
1) Make sure the headset is powered on and the power adapter is not connected (you can’t use the
headset while it’s charging).
2) Press and hold MFBuntil the LED flashes alternating red and blue (approximately ꢂ seconds),
then release. The headset is in pairing mode and should be visible to other Bluetooth devices.
ꢀ) On your phone, start a search for Bluetooth headsets or handsfree devices. (This process may
take several seconds, and it will be different for each phone; see your phone’s manual for
detailed instructions.)
ꢃ
ꢁ) Your phone should discover a device called a BT230 or BT230 headset, When your phone asks if
you want to pair with this device, select yes.
5) When your phone prompts you for a PIN code or password to pair with the BT2ꢀ0, enter 0000.
NOTE: If your phone supports Bluetooth 2.1, you do not need to enter a password.
ꢂ) When the headset is paired, the blue LED flashes twice every 5 seconds; your phone might also
display a confirmation message.
NOTE: If the blue LED flashes once every 5 seconds, the headset is not paired. Try the
pairing procedure again.
Connect to Your phone
Most phones connect to the headset as soon as you pair it; if yours won’t, turn the headset
off and back on. If the headset still won’t connect, check your phone’s owner’s manual for
additional Bluetooth information.
once the Headset is paired
► Whenever you turn the headset on, it will automatically try to connect to whatever device it was
connected to last.
ꢄ
► If the headset loses the connection for more than ꢀ0 seconds (e.g., if your phone is out of range),
it goes into idle mode. To manually reconnect, press MFB once. If the headset comes back in
range in less than ꢀ0 seconds, it will automatically reconnect without pressing MFB.
UsinG YoUr HeadseT
Turning the
headset on
To turn the headset on, slide the power button to the ON position. The blue
LED flashes and you hear the turn-on melody (about ꢁ seconds).
Turning the
headset off
Slide the power button to its original position.
put your headset on
Insert the ear cushion, then wrap
the earhook behind your ear.
Everyone’s ear has a sweet
spot, a particular angle of
the speaker where the audio
ꢅ
comes in loud and clear. Move the headset around until you find the best angle for the ear
cushion.
wearing the Headset on Your Left ear
If you want to wear the headset on your left ear,
take the earhook off and turn it over.
FeaTUres
Basic
After the headset is connected, you can use the following features:
Make the call from your mobile phone as usual; your phone should automatically
Make a call send the call to the headset; if it doesn’t, press and hold MFB for 2 seconds to
manually send the call to the headset.
Answer a call While the phone is ringing, press MFB.
End a call
Reject an
Press MFB. You can also end the call from your mobile phone.
While the phone is ringing, press and hold MFBfor at least 2 seconds. Wait
incoming call until you hear a beep before you release the button.
10
Press and hold MFBfor 2 seconds to transfer the current call from your phone
Transfer a call
Redial the
to headset (and back).
With the phone in standby, press MFB. The headset automatically dials the last
last number number you dialed from your phone.
Call waiting
To use this feature, you must subscribe to Call Waiting through your service provider, and
your phone must support the hands-free profile.
To put your current call on hold and switch to a waiting call, press and hold Upuntil you
hear 1 beep (about ꢁ seconds). When you release the button, you’ll be connected to the
waiting call. (Press and hold Upagain to switch back to the original call.)
Voice-activated dialing
To use this feature, your phone must support voice dialing, and all voice commands must
already be programmed.
► To activate voice dialing, make sure your phone is in standby. Press and hold MFBuntil you
hear a beep (about 2 seconds).
11
► To deactivate voice dialing, press and hold MFBuntil you hear a beep (about 2 seconds).
NOTE: If you are in Voice Activated Dialing mode and you activate Last Number Redial, Voice-
Activated Dialing turns off and the last number is dialed.
► Use your pre-programmed voice commands as you would with your phone. (For best results, try
recording your voice tags through your headset. )
UsinG THe MULTipoinT FUnCTion
The headset supports simultaneous connection with 2 mobile phones with full control of
each one. (This feature may not be compatible with some mobile phones.)
pairing to More than one phone
Pair the headset to the first phone following the instructions on page ꢃ. When you set the
headset in pairing mode and hear a high-pitched, short double-beep, pair the headset to
the second phone.
Using Both phones
► The headset stays connected to both phones until a call comes in. If you answer the call, the
headset automatically disconnects from the other phone while the call is active. When you hang
up, the headset automatically reconnects to the other phone.
12
► Only one phone at a time can be on an active call.
► The headset plays a different ring tone for each phone so you know which one is ringing. To
answer the incoming call, press MFBas usual.
► All the button functions remain the same for the first phone (the one you paired first).
► To use last number redial on the second phone, press and hold Downfor about 2 seconds.
(When you hear a beep, release the button.)
► To activate voice dialing on the second phone, press and hold Upfor about 2 seconds. (When
you hear a beep, release the button.)
TroUBLesHooTinG and MainTenanCe
If you have problems with the headset, see the suggestions in the table below. If these
suggestions don’t help, contact customer support (see the cover for contact information).
If...
Try...
The headset won’t turn on. • Charging the battery completely.
• Making sure your phone is in pairing mode. Check your phone’s manual for
The headset won’t pair with
my phone.
instructions on Bluetooth device pairing.
• Resetting the headset.
• Seeing if your phone supports the Bluetooth Headset or Hands Free profiles.
1ꢀ
If...
Try...
The headset paired with
• Making sure the call connected and is still active.
my phone, but I can’t hear • Making sure the phone transferred the call to the headset. Press and hold
anything through it.
MFBfor two seconds to transfer the call.
The headset keeps beeping,
and I don’t know why.
• Seeing if the battery is getting low. If the LED is blinking red, charge the
battery.
• Turning the speaker volume up.
I can hear the caller, but the
audio is very weak or soft.
• Moving closer to your phone (if you aren’t carrying it).
• Keeping the battery fully charged; As the battery starts to run out, the speaker
gets softer.
reset the Headset
NOTE: Before resetting the headset, make sure the headset is not connected to any mobile
phones (e. g. headset is in connectable mode).
Press and hold MFB+ Downfor ꢁ seconds. The LED flashes 5 times and the
headset beeps. Once the headset is reset, all the mobile phone links are deleted.
General InformatIon
• You cannot use the headset while it is recharging.
• Bluetooth wireless devices have a maximum range of ꢀ0 feet (10 m); the actual range varies depending on
current conditions (obstacles, battery power, interference, etc.).
1ꢁ
• The headset can be connected only to devices that support the Bluetooth headset or hands-free profile. It is
not compatible with standard cordless phones.
Battery liFe
• With average use, the battery should provide about ꢂ hours of talk time and ꢃ days of standby time. If a
battery is new or left unused for a long time, it can have reduced capacity the first few times you use it. For
maximum battery life, keep the battery charged.
• When the battery only has enough charge for about 15 minutes of talk time, the headset triggers a low
battery alert: you’ll hear a periodic beep, and the LED changes from blue to red.
• When the battery no longer has enough charge to operate the headset, the headset will power off; you won’t
be able to turn it back on until you charge the battery.
NoiSeorStaticoN tHeHeadSet
The most common cause of noise or static on any wireless device is interference. Bluetooth devices operate in
the ISM band (2.ꢁ02 GHz ~ 2.ꢁꢄ0 GHz); any equipment operating in this frequency range might interfere with
the headset. Some common sources of interference in this range are
• Equipment that uses microwaves, especially microwave ovens
• Wireless LAN equipment or WiFi connections
• Other Bluetooth devices or computers
• Certain cordless telephones
• Certain medical equipment and appliances
If you have problems with static during calls, look for one of these interference sources. Try moving away from
the suspected source.
15
If the noise continues, there may be interference
on your phone itself, and any noise in the phone’s
connection will come through on the headset, too.
Transfer the call to your phone and see if the audio
quality improves. If it doesn’t, look around for things
that can interfere with your phone.
• Set the volume at the minimum level needed to
hear in the current environment. If possible, use
your headset in quiet surroundings or try to move to
an area with less background noise before adjusting
the volume.
• Start with the volume at its lowest setting, then
gradually increase it until you can hear.
• Turn the volume down before powering off the
headset and readjust the volume each time you
turn it on.
Safety and HandlInG
InformatIon
For maximum product life, do not drop, throw, or
crush the headset. Do not expose it to humidity, dust,
or temperatures above 125 F.
• If someone next to you can hear the other end of the
call through your headset or if your ears hurt or ring
when you hang up, the volume is too high.
• The longer your ears are exposed to noise, the
greater the risk of damage. Limit calls at higher
volumes (or other exposure to loud noise).
• For more information on protecting your hearing,
gov/health/wise/) or consult an audiologist.
cleaNiNgtHeHeadSet
• If necessary, remove the earhook. Dampen a lint-
free cloth with water or a cleaner specially designed
for electronics, and gently wipe the headset clean.
• Do not expose this product to liquid (water, alcohol,
etc.) or submerse in liquid for any reason.
importaNtSaFety iNStructioNS
avoidiNgHeariNgdamage
uniden america corporation doeS Notrepresent this
product to be waterproof. to reduce the risk of fire,
electricalshock, or damage to the product, doNot
expose this product to rain or moisture.
Using any headset or earbud at too high a volume can
cause permanent hearing damage. To reduce the risk
of hearing damage:
When using the headset, always follow basic safety
precautions to reduce the risk of fire, electric shock
and injury to persons, including the following:
• Do not use this product near water, for example,
near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
• Use only the power cord and batteries indicated
in this manual. Do not expose the battery (or the
device) to flames or dispose of it in a fire: the battery
may explode. Check with local authorities for
possible battery disposal instructions.
fire. Follow all warning notices in your immediate
area!
SavetHeSeiNStructioNS!
FccNotice
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) This device must accept any interference
received, including interference that may cause
undesired operation. Privacy of communications may
not be ensured when using this product.
• Do not disassemble, modify, or attempt to repair any
component of this product.
To insure the safety of users, the FCC has established
criteria for the amount of radio frequency energy
various products may produce depending on their
intended usage. This product has been tested and
found to comply with the FCC’s exposure criteria. For
body worn operation, the FCC RF exposure guidelines
were also met when used with the Uniden accessories
supplied or designed for this product. Use of other
accessories may not ensure compliance with FCC RF
exposure guidelines and should be avoided.
• Check the laws and regulations on the use of
mobile phones and hands-free equipment in the
areas where you drive. Always give full attention to
driving and pull off the road and park before making
or answering a call if driving conditions require.
• Do not allow children to play with the headset:
since it contains small parts that could become
detached and create a choking hazard.
• Turn off your headset when pumping gas, handling
flammable materials, or in any area with a risk of
explosion. In rare occurrences, this product could
generate sparks which can cause an explosion or
iNduStry caNadaStatemeNt
two-year lImIted warranty
This device complies with RSS-210 of the Industry
Canada Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept
any interference received, including interference that
may cause undesired operation.
evidence of originalpurchase is required for warranty
service.
WARRANTOR: UNIDEN AMERICA CORPORATION
(“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for
two years, to the original retail owner, this Uniden
Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions
set out below.
WARRANTY DURATION: This warranty to the original
user shall terminate and be of no further effect 2ꢁ
months after the date of original retail sale. The
warranty is invalid if the Product is a) damaged
or not maintained as reasonable or necessary, b)
modified, altered, or used as part of any conversion
kits, subassemblies, or any configurations not sold
by Uniden, c) improperly installed, d) serviced or
repaired by someone other than an authorized
Uniden service center for a defect or malfunction
covered by this warranty, e) used in any conjunction
with equipment or parts or as part of any system
not manufactured by Uniden, or f) installed or
IMPORTANT NOTE: RADIATION ExPOSURE
STATEMENT
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions
for satisfying RF exposure compliance. To maintain
compliance with IC RF exposure compliance
requirements, please follow operation instruction as
documented in this manual.
litHium-polymerBattery iNFormatioN
This device contains a lithium-polymer battery. The
headset and battery must be recycled or disposed
of properly. Contact your local waste management
office for information on battery recycling or disposal.
programmed by anyone other than as detailed by the consequential damages so the above limitation or
owner’s manual for this product. exclusion may not apply to you.
STATEMENT OF REMEDY: In the event that the product LEGAL REMEDIES: This warranty gives you specific
does not conform to this warranty at any time while
this warranty is in effect, warrantor will either, at its
legal rights, and you may also have other rights
which vary from state to state. This warranty is void
option, repair or replace the defective unit and return outside the United States of America and Canada.
it to you without charge for parts, service, or any
other cost (except shipping and handling) incurred
by warrantor or its representatives in connection
with the performance of this warranty. Warrantor,
at its option, may replace the unit with a new or
refurbished unit.
PROCEDURE FOR OBTAINING PERFORMANCE OF
WARRANTY: If, after following the instructions in the
owner’s manual you are certain that the Product is
defective, pack the Product carefully (preferably in
its original packaging). The Product should include
all parts and accessories originally packaged with
the Product. Include evidence of original purchase
and a note describing the defect that has caused you
to return it. The Product should be shipped freight
prepaid, by traceable means, to warrantor at:
Uniden America Service
THE LIMITED WARRANTY SET FORTH ABOVE IS THE
SOLE AND ENTIRE WARRANTY PERTAINING TO THE
PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL
OTHER WARRANTIES OF ANY NATURE WHATSOEVER,
WHETHER EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not
allow this exclusion or limitation of incidental or
ꢁꢃ00 Amon Carter Blvd.
Fort Worth, TX ꢃꢂ155
© 2010 Uniden America Corp.
Ft. Worth, Texas
|
