Quick start guide
LS6375-3 (LS6325-2 and IS6100)
Introduction
This quick start guide provides you with the basic installation
and use instructions. A limited set of features are described in
abbreviated form.
Please refer to the user’s manual for complete installation and
operation instructions.
Telephone base and handset charger installation
Install the telephone base and handset charger as shown below.
Telephone
Electrical outlet not
wall jack
controlled by a wall switch
Telephone
line cord
If you have DSL
high speed
Telephone base
power adapter
Internet service,
a DSL filter (not
included) is
required.
Handset
charger
adapter
Telephone base
Handset charger
Use only the power adapters and batteries supplied with
this product.
Handset battery installation and charging
Install the handset battery as shown below. Once you have
installed the handset battery, you may be able to make and
receive short calls. For best performance, charge the handset
battery continuously for at least ꢀ6 hours.
2
ꢀ
Place the battery with the
wires inside the battery
compartment.
Plug the battery connector
securely into the socket,
matching the color-coded
label.
3
4 Charge the handset in the
telephone base.
Slide the battery
compartment towards the
center of the handset until it
clicks into place.
CHarge light
remains on
when charging.
Download from Www.Somanuals.comꢀ. All Manuals Search And Download.
Handset overview
CHarge light
On when the handset is
charging.
VOL/CID
(volume/caller ID)
Review the call log
when the telephone is
not in use.
Scroll down while in a
menu.
/ VOL
(directory/volume)
Review the directory
when the telephone is
not in use.
Scroll up while in a
menu.
Decrease the listening
volume during a call.
MeNU/SeLeCT
Show the menu.
Increase the listening
volume during a call.
Select an item or save
a setting while in a
menu.
(speakerphone)
Make, answer or join
a call.
Switch between the
speakerphone and
handset during a call.
PUSH TO TaLK (PTT)
Begin a one-to-one or
one-to-all broadcast
message.
OFF/CLear
Hang up a call.
Silence the ringer
temporarily while the
handset is ringing.
/FLaSH
Make, answer or join
a call.
Answer another
incoming call during
a call.
Press and hold to
erase the missed call
indicator when the
telephone is not in use.
1
Press repeatedly to add
or remove 1 in front of a
call log number before
dialing or saving it in
the directory.
Return to the previous
menu while in a menu.
Press and hold to
return to idle mode
while in a menu.
TONe
Dialing keys
Switch to tone dialing
temporarily during a
call.
Enter numbers or
characters.
#
reDIaL/PaUSe
Press repeatedly to show
other dialing options
when reviewing a call
log entry.
Review the redial list.
Press and hold to
insert a dialing pause
while dialing or
eQ
entering numbers.
Change the audio quality
during an outside call,
intercom call, message or
announcement playback.
MUTe/reMOVe
Mute the microphone during a call.
Delete the displayed entry while reviewing
the call log, directory or redial list.
Silence the ringer temporarily while the
handset is ringing.
Delete digits when predialing.
Headset overview
(on/off)
Press and hold two seconds to power on or off.
Answer, join or end a call.
On in red when charging in the headset charger.
On in blue when fully charged in the headset charger.
Flashes once every ꢀ0 seconds in blue when in idle mode.
Flashes once every ꢀ0 seconds in red when in low battery mode.
Flashes twice every three seconds in blue while on a call.
Flashes quickly and alternately in red and blue while being
registered.
Flashes four times every four seconds in blue when there is an
incoming call.
earpiece
MUTe/FLaSH
rotating
Mute the microphone while
on a call.
Press and hold to answer
another incoming call during
a call.
Silence the ringer in the
earpiece temporarily when
there is an incoming call.
+/-/VOLUMe
clip
Adjust the
Connect
the ear
hook or
head
listening volume
while on a call.
Adjust the ringer
volume when
the headset is
not in use.
band.
reSeT
inset button
Microphone
Download from Www.Somanuals.com3. All Manuals Search And Download.
Using the menu
To enter the handset menu:
>
The symbol
indicates the
feature to select.
ꢀ. Press MeNU/SeLeCT when the handset is
not in use.
>Ringers
Settings
2. Press
/
VOL or VOL/CID until the
> symbol displays next to the desired
feature menu.
3. Press MeNU/SeLeCT to enter that menu.
• To return to the previous menu, press OFF/CLear.
• To return to idle mode, press and hold OFF/CLear.
Telephone settings
Default settings are indicated by an asterisk(*).
Screen display
LCD language
Function
Options
Set the screen display
language.
english*
Français
español
Clr voicemail
Key tone
Turn off the voicemail
indicators.
Turn off indicator?
Set whether the handset
beeps whenever a key is
pressed.
On*
Off
Set date/time
Set the date and time for
the telephone system.
--:-- --/--
_ _ _
Home area code
Set the home area code
so that the call log stores
only seven digits for local
telephone numbers.
Dial mode
Set the handset to be tone Tone*
dial or pulse dial.
Pulse
Telephone operation
Make a call
• Press
/FLaSH or
on the handset and
then dial the telephone number. Press
on the headset to join the call and hang
up the handset at any time.
-Or-
• Predial by first dialing the telephone number and then press
/FLaSH or
on the handset. Press
on the headset to join
the call and hang up the handset at any time.
answer a call
Press
on the headset, or
/FLaSH,
or any of the dialing
keys on the handset.
end a call
• Press on the headset or place the headset in its charger.
• Press OFF/CLear on the handset or place the handset in the
telephone base or its charger.
redial
Each system handset stores the 20 most
recently dialed numbers. When there are
already 20 entries, the oldest entry is deleted
to make room for the new entry.
To review and dial a number from the redial list:
ꢀ. Press reDIaL/PaUSe when the handset is not in use.
2. Press
/
VOL, VOL/CID or reDIaL/PaUSe repeatedly until the
desired entry displays.
3. Press
/FLaSH or
to dial.
To delete a redial entry:
When the desired redial entry displays, press MUTe/reMOVe.
Download from Www.Somanuals.com4. All Manuals Search And Download.
Intercom
Use the intercom feature for conversation between two system
handsets, or a handset and a headset.
• You can use a maximum of five handsets, or four handsets and
a headset at the same time. Only two handsets, or one handset
and one headset can be used on an intercom call. Only three
handsets, or two handsets and one headset can be used on an
outside call.
• If there is an incoming call while the originating handset is
making an intercom request, the intercom request will be
stopped.
To initiate an intercom call:
Press INT when the handset is not in use.
• If you have more than two handsets, use the dialing keys to
select the destination handset or press # (pound key) for the
destination headset.
To answer an intercom call:
• Press
/FLaSH,
, INT or any of the dialing keys on the
destination handset.
• Press on the headset.
To end an intercom call:
• Press OFF/CLear or place the handset back in the telephone
base or its charger.
• Press or place the headset in its charger.
Push to talk (PTT)
Use the push to talk feature to broadcast messages from one
handset to the speakerphone of one or all other handsets.
• Only one PTT can be active at a time and only one handset
can talk at a time.
• You must release PUSH TO TaLK so the other person can
respond.
• While PTT is in use between two handsets, other handsets
cannot use the intercom feature but can access the answering
system.
To initiate a PTT call:
ꢀ. Press and hold PUSH TO TaLK when the handset is not in
use. When the connection is made, all handsets display
Press and hold [PTT] to talk and beep once.
2. Press and hold PUSH TO TaLK on your handset again. A
chirp indicates your microphone is on. Speak towards the
handset. Your voice is broadcast to all destination handsets.
3. Release PUSH TO TaLK after speaking. All handsets beep
once again. After the handsets beep, you can press and hold
PUSH TO TaLK to continue speaking or the destination
handsets can respond.
To answer a PTT call:
ꢀ. When your handset receives a PTT call, the handset beeps
and the screen displays Press and hold [PTT] to talk.
2. When someone else is speaking, your speakerphone light is
on. When your speakerphone light is off, press and hold
PUSH TO TaLK on your handset. When you hear a chirp,
speak towards the handset.
3. Release PUSH TO TaLK after speaking. Your handset will
beep. After the beep, you can press and hold PUSH TO TaLK
to continue speaking or the destination handset can respond.
To end a PTT call:
Press OFF/CLear or place the handset back in the telephone
base or charger.
Download from Www.Somanuals.com5. All Manuals Search And Download.
Directory
The directory can store up to 50 entries.
To add a directory entry:
ꢀ. Press MeNU/SeLeCT when the handset is not in use.
2. Scroll to select >Directory and then >add contact.
3. When the screen displays eNTer NUMBer:
• Use the dialing keys to enter the number (up to 30 digits).
-Or-
• Copy a number from the redial list by pressing
reDIaL/PaUSe and then press
/
VOL, VOL/CID or
reDIaL/PaUSe repeatedly to choose a number. Press
MeNU/SeLeCT to copy the number.
4. Press MeNU/SeLeCT to move to the name.
5. When the screen displays eNTer NaMe, use the dialing
keys to enter the name (up to ꢀ5 characters). Additional key
presses show other characters of that particular key.
6. Press MeNU/SeLeCT to confirm.
While entering names and numbers, you can:
• Press MUTe/reMOVe or OFF/CLear to backspace and erase a
digit or character.
• Press and hold MUTe/reMOVe to erase the entire entry.
• Press
or left.
/
VOL or VOL/CID to move the cursor to the right
• Press and hold reDIaL/PaUSe to insert a dialing pause.
• Press 0 to add a space.
To review and dial a directory entry:
Entries are sorted alphabetically.
ꢀ. Press
/
VOL when the handset is not in use.
2. Scroll to browse through the directory, or use the dialing keys
to start a name search.
3. When the desired entry appears, press
/FLaSH or
to dial.
To edit a directory entry:
ꢀ. When the desired entry displays, press MeNU/SeLeCT.
2. When the screen displays eDIT CONTaCT >Name:
• Press MeNU/SeLeCT to edit the name. Use the dialing keys
to edit.
-Or-
• Scroll to select >Number and then press MeNU/SeLeCT to
edit the number. Use the dialing keys to edit.
2. Press MeNU/SeLeCT to save.
To delete a directory entry:
ꢀ. When the desired entry displays, press MUTe/reMOVe.
2. When the screen displays Delete contact?, press
MeNU/SeLeCT to confirm.
Caller ID
This product supports caller ID services provided by most
telephone service providers. Depending on your service
subscription, you may see the caller’s name, number, date and
time of calls that are sent by your telephone service provider after
the first or second ring.
Call log
The call log stores up to 50 entries. If you answer a call before
the caller information appears on the screen, it will not be saved
in the call log.
• The handset displays XX Missed call(s) when there are calls
that have not been reviewed in the call log.
• If you want to erase the missed call indicator, press and hold
OFF/CLear on the idle handset.
To review and dial a call log entry:
Mike Smith
595-9511
ꢀ. Press VOL/CID when the handset is
not in use.
2. Scroll to browse through the call log.
When the desired entry appears:
12:15PM
12/25
• Press # repeatedly to show
Press #
Press #
Press #
Press #
-Or-
Press 1
Press 1
1-800-595-9511
595-9511
different dialing options.
• Press 1 repeatedly if you need
to add or remove ꢀ in front of the
telephone number.
1-595-9511
800-595-9511
1-800-595-9511
800-595-9511
3. Press
/FLaSH or
to dial the
displayed number.
Download from Www.Somanuals.com6. All Manuals Search And Download.
To save a call log entry to the directory:
ꢀ. When the desired call log entry displays, press MeNU/SeLeCT.
2. When the screen displays eDIT NUMBer, use the dialing
keys to modify if necessary.
3. Press MeNU/SeLeCT.
4. When the screen displays eDIT NaMe, use the dialing keys to
modify if necessary.
5. Press MeNU/SeLeCT to confirm.
To delete the call log entries:
• Delete an entry: When the desired call log entry displays,
press MUTe/reMOVe.
• Delete all entries: Press MeNU/SeLeCT when the handset is
not in use. Scroll to select >Call log and then >Del all calls.
Press MeNU/SeLeCT.
about answering system and voicemail
Your telephone has separate indicators for two different types of
voice messages: those left on the built-in answering system and
those left at your telephone service provider’s voicemail. Each
alerts you to new messages separately.
• If
and New VOICeMaIL display on the handsets, your
telephone service provider is indicating that it has new
voicemail for you. Contact your telephone service provider for
more information on how to access your voicemail.
• If
and XX New messages show on the handsets and the
message window on the telephone base flashes, there are
messages recorded on the built-in answering system. It can
record and store up to 99 messages and each message can be
up to four minutes in length.
answering system settings
Default settings are indicated by an asterisk(*).
Screen display
Call screening
Function
Options
On*
Off
Set whether you hear the callers
while they are leaving messages
to you.
# of rings
Set the number of times the
telephone rings before the
answering system answers.
Toll saver allows you to check
for new messages and avoid
paying unnecessary long distance
charges when you are not calling
from your local area.
6
4*
2
Toll saver
remote code
Set a two-digit security code to
access the answering system
remotely from any touch-tone
telephone.
19*
Msg alert tone
Set whether the telephone beeps On*
every ꢀ0 seconds to alert you of
new messages.
Off
answering system operation
Turn the answering system on or off
The answering system must be turned on to answer
and record messages. When it is turned on, the
/aNS ON/OFF light on the telephone base turns
on and aNS ON displays on the handset.
• Press /aNS ON/OFF on the telephone base to
turn the built-in answering system on or off.
record your own announcement
You can use the preset announcement to answer calls, or
replace it with your own recorded announcement. It can be up to
90 seconds in length.
ꢀ. Press MeNU/SeLeCT when the handset is not in use.
2. Scroll to select >answering Sys. Press MeNU/SeLeCT again.
3. The handset announces, “To play, press 2. To record, press
7.” Press 7 to record.
4. The handset announces, “Record after the tone. Press 5 when
you are done.” After the tone, speak towards the handset
microphone.
5. Press 5 when finished.
6. The answering system automatically plays back the newly
recorded announcement. Press 5 to stop the playback at any
time; 2 to replay the recorded announcement; or 7 to record
again if desired.
Download from Www.Somanuals.comꢁ. All Manuals Search And Download.
Play messages
To play messages with the telephone base:
Press
/PLaY/STOP when the telephone is not in use.
Options during playback:
• Press /VOL+ or /VOL- to adjust the speaker volume.
• Press /SKIP to skip to the next message.
• Press /rePeaT to repeat the message currently playing.
Press /rePeaT twice to listen to the previous message.
• Press X/DeLeTe to delete the current message. The system
advances to the next message.
• Press
/PLaY/STOP to stop.
To play messages with a handset:
Press MeNU/SeLeCT twice when the telephone is not in use.
If you have either new or old messages, the messages play
automatically. If you have both new and old messages:
• To play new messages, press MeNU/SeLeCT to select
>Play new msgs.
• To play old messages, scroll to select >Play old msgs and
then press MeNU/SeLeCT.
Options during playback:
• Press / VOL or VOL/CID to adjust the speaker volume.
• Press
quality.
eQ to adjust the handset message playback audio
• Press 6 to skip to the next message.
• Press 4 to repeat the message currently playing. Press 4 twice
to listen to the previous message.
• Press 3 to delete the current message. The system advances
to the next message.
• Press 5 to stop.
Delete all messages
To delete all messages at the telephone base:
Press X/DeLeTe when the phone is not in use.
To delete all messages with a handset:
ꢀ.Press MeNU/SeLeCT when the handset is not in use.
2.Scroll to select >answering Sys and then >Delete all old
messages? Press MeNU/SeLeCT.
Call intercept
If you want to talk to the person whose message is being
recorded, press
/FLaSH or
on the handset.
access the answering system remotely
ꢀ.Dial your telephone number from any touch-tone telephone.
2.When the system plays your announcement, enter the
two-digit remote code. The preset code is 19.
3.Then you can enter one of the following remote commands.
Command
Function
1
2
Play all messages.
Play only new messages.
3
Delete the current message (during playback).
Delete all old messages.
33
4
Repeat the current message (during playback).
Skip to the previous message (during playback).
Stop.
44
5
*5
6
Hear a list of remote commands.
Skip to the next message (during playback).
Record a new announcement.
End the call.
*7
8
0
Turn the answering system on or off.
4.Hang up or press 8 to end the call.
IMPOrTaNT!
If you have difficulty with your telephone and headset, please
refer to the user’s manual for a full set of installation and
operation instructions. For customer service, visit our website at
96-00ꢁꢁ22-0ꢀ0-ꢀ00
Download from Www.Somanuals.comꢂ. All Manuals Search And Download.
|