Product Features
Additional
High contrast color TFT LCD display support resolution up to XGA
Read all of these instructions and save them for later use.
1024×768. @75Hz.
Follow all warnings and instructions on the product.
Product
Compatible VESA standards.
Imbedded audio system provides sound performance.
Power management system conforms to VESA DPMS standard.
Support DDC 1/2B for Plug & Play compatibility.
Advanced OSD control for picture quality adjustment.
Detachable stand for wall-mounting application.
♦ Do not cover block the vent holes in the case.
♦ Do not insert sharp objects or spill liquid into the LCD monitor through
cabinet slots. They may cause accident fire, electric shock or failure.
♦ Disconnect the power plug from the AC outlet if you will not use it for
an extended period of time.
♦ Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks.
♦ Do not touch the screen directly with your fingers. You may damage the
screen, and oil from your skin is difficult to remove.
♦ Do not apply pressure to screen. The LCD is very delicate.
Power
Screen cleaning techniques
Gently clean the screen with a clean camel hair lens brush, or a soft,
clean, lint-free cloth, to remove dust and other particles that can scratch
the screen.
Do not apply pressure to the screen surface when wiping it clean.
Do not pour or spray any liquid directly onto the screen or casing.
Chemical cleaners have been reported to damage the screen or case of
the LCD monitor.
♦Use the type of power indicated on label.
Plugs
♦Do not remove any of the prongs of the monitor’s three-pronged power
plug.
♦Disconnect the power plug from the AC outlet under following
conditions：
If you will not use it for an extended period time.
When the power cord or plug is damaged or frayed.
If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions. Improper adjustment of other
controls may result in damage and will often require extensive work
by a qualified technician.
If the product exhibits a distinct change in performance, service may
be required.
Page 2
Page 3
2. Control Function
Control Button Front View
Power and extension cords
♦ Do not allow anything to rest on the power cord.
♦ Do not locate this product where persons will walk on the cord.
♦ Use the proper power cord with correct attachment plug type. If the
power source is 120V AC, use a power cord that has UL and C-UL
approvals, If the power source is a 240V AC supply, use the tandem (T
blade) type attachment plug with ground conductor power cord that
meets the respective European country’s safety regulations, such as VDE
for Germany.
﹝2﹞ ﹝3﹞ ﹝1﹞ ﹝4﹞ ﹝5﹞
♦ Do not over load wall outlets or power cords. Ensure that the total of all
units plugged into the wall outlet does not exceed 10 amperes.
♦ Ensure that the total ampere ratings on all units plugged into the extension
cord is not above the cord’s rating.
♦ If the power supply cord, which came with your monitor, is to be
connected to the PC instead of the wall outlet, Use an UL/TUV approved
computers with receptacle rated 100~240V AC, 50/60Hz, 1.0A(minimum)
only.
1.Power Switch
2. Auto adjust
：
：
Power switch & LED.
Select this function to obtain the best display
efficiency
3.OSD menu / select
4.Adjust (decrease－)
5.Adjust (increase＋)：
：
：
：
Pressing this button pops up the OSD menu
on the screen Add used to select the OSD
control options on the screen.
Environment
♦ Place the monitor on a flat and leveled surface.
♦ Place the monitor in a well-Ventilated place.
This button is used to adjust the decreasing
value of selected.
♦ Keep the monitor away from：
♦ Overly hot, cold or humid places, places directly under sunlight, dusty
surroundings, equipment that generate strong magnetic fields.
♦ Please adjust the frequency to 75 Hz after setting up the LCD monitor.
♦ Then push the OSD menu button and use the Auto Adjust function to find
the best mode of your computer.
OSD off is volume adjust －
This button is used to adjust the increasing
value of selected.
OSD off is volume adjust ＋
Page 4
Page 5
OSD Controls
Picture Menu：
Auto adjust
：Select this function to efficiently obtain the best
display solution.
Monitor Function Selection Menu：
Brightness
Contrast
Reset
：Adjust the brightness using＋and－buttons.
：Adjust the contrast using＋and－buttons.
：Recall Factory setup function.
PICTURE
：Select this function to Picture sub menu.
ADVANCED PIC ：Select this function to Advanced Picture sub
Exit
：Return to Selection menu.
menu.
SOUND
：Select this function to Sound sub menu.
UTILITY
EXIT
：Select this function to Utility sub menu.
：Select this function to exit OSD menu.
Sub Menu (Auto adjust)：
Accept
Retry
：Select this function to accept auto adjust.
：Select this function to retry auto adjust.
Cancel
：Select this function to cancel auto adjust.
Page 6
Page 7
Sound Menu：
Volume
Mute
：Adjust the volume using＋and－buttons.
：Mute function.
Exit
：Return to Selection menu.
Advanced Picture Menu ：
：Pressing＋moves the display image to right ; Pressing
－moves the display image to left.
H Position
V Position
：Pressing＋moves the display image upward ; Pressing
－moves the display image downward.
Phase
Clock
：Adjust the phase using＋and－buttons.
：Adjust the clock using＋and－buttons.
Utility Menu：
Auto Color ：Select this function to obtain the best display color.
Exit
：Return to Selection menu.
OSD Language
：Select the Language Letter Font.
：Select this function to OSD control sub menu.
OSD Control
Exit
：Return to Selection menu.
Page 9
Page 8
3.Input Diagrams
Inputs
【AUDIO】
OS Language Menu：
【AVI】
English I
ENGLISH II
Exit
：Select Small Letter Font.
：Select Capitalize Letter Font.
：Return to Utility Menu.
【1】 【2】 【3】 【4】 【5】
【6】
【1】DC IN
：This is for connecting the adapter DC 12V cable.
【2】AV IN
：RCA jack AV signal input.
：S-Video signal input.
【3】S-VIDEO IN
【4】LINE OUT
： Sound signal output(Stereo Phone Jacket).
：Audio signal R/L input.
OSD Control Menu ：
【5】RCA JACK
AUDIO IN
：Pressing＋moves the OSD menu to downward ;
Pressing－moves the OSD menu to upward.
V Position
H Position
【6】VGA IN
：This can be connected with the D-sub 15 pin
signal connector.
：Pressing＋moves the display image right ; Pressing
－moves the display image left.
Halftone
Duration
Reset
：Adjust the shade of the OSD menu.
：Adjust the OSD show time.
：Recall Factory setup function.
：Return to Utility menu.
Page 10
Exit
Page 11
4. Setup
Electrical Connection
5. Viewing Angles
Tilting
Please follow the instruction below to properly connect the LCD monitor
to external electrical source.
For better viewing angle, you may tile the LCD monitor forwards (up to 10
degrees) or backwards (up to 25 degrees, 90 degrees for packing).
1. Connect the female-end of the power cable to the transformer. Connect
the male-end of the power cable to the wall outlet or extension cable.
2. Connect the cable from the other end of the transformer to the LCD
monitor located at the back near the VGA signal cable.
Signal Connection
Down：10 o
1. Power off both the LCD monitor and PC system before connecting them.
2. Take out the VGA cable from the box, then connect it to the signal
connector at the back of the LCD monitor.
3. Connect the other end to the VGA connector on the back of the PC
system.
4. Please make sure the connections between the PC system unit and the
LCD monitor is strong and secure. Please don’t forget to tighten the
screws on each connector end.
5. Now turn on both the PC system unit and the LCD monitor.
6. After you finish setting up the LCD monitor, please set the refresh rate to
75Hz.
7. After setting up the LCD monitor, please perform Auto Adjust in OSD so
that the LCD monitor will automatically set to optimum color display
each time.
Up：25 o
* Please note: When you disconnect any power cable or signal cable, please
do not pull the cable by grabbing the cable body. Please grab the cable
connector itself whenever you try to pull the cable during disconnect.
Page 12
Page 13
6. Troubleshooting
8. Product Specifications
No power
Make sure the A/C power cord is securely connected to the monitor and to the
power outlet.
Type
AUDIO
DVI
Spec
No screen image with power on
LCD Display
Pixel Pitch
Max. Resolution
Set Size
14.1” Active matrix TFT LCD panel
0.279(H) x 0.279(V) mm
(1)Make sure the video cable supplied with the monitor is tightly secured to
both the video output port of the computer and the monitor.
(2)Adjust the brightness and contrast from the front panel controls.
“No Signal Input” message shown
1024(H) x 768(V) XGA
375(W) × 360(H) × 185(D) mm
Pack Size
422(W) × 426(H) × 214(D) mm
200:1 (option 300:1)
150 cd/m2 (option 200)
25 ms (typ)
(1)Make sure the video cable is tightly connected to the computer and
monitor.
Contrast Ratio
Brightness
(2)Check the 15-pin video cable connectors on both ends have exactly 15
pins.
Response Time
Display Color
View Angle
262,144
L+/R- ±50°
U+/D- +20° -35°
If the problem is still there, please contact your ViewEra dealer or ViewEra.
PC Interface
Video Sync.
Display Mode
RGB analog or digital 0.7V peak to peak
TTL positive or negative.
VGA, SVGA, XGA
7.Service Information
Warranty
Power consumption ON<36W (maximum)
Frequency
(Horizontal) 31.5-60KHz (Vertical) 56-75Hz
The ViewEra V140 TFT-LCD monitors are warranted for three(3) years
for all parts and one(1) year for LCD panels from the date of purchase.
ViewEra warrants its products to be free from defects in material and
workmanship during the warranty period.
Signal Connector
Front Control
D-sub 15 pin and CVBS / S-Video (O\option)
Auto adjust, Power SW with LED, OSD Menu,
＋/－ Adjustment
OSD Menu
Brightness, Contrast, Auto Adjust, Clock, Phase,
H-Position, V-Position,
Service
(1) Please contact your ViewEra dealer for warranty service.
(2) For out-of-warranty service, you may contact either ViewEra dealers or
ViewEra.
Power Adapter
AC Input : 100-240V~1.8A, 50-60Hz
DC Output : 12V/ 3.0A
Page 15
Page 14
9. Windows setup
Operating
Conditions
Storage
Temperature: 0℃~40℃
Humidity : 20% ~ 85%
For the best view, please set up with the monitor type in Windows.
Please select as follows:
Temperature: -20℃~60℃
Conditions
Certification
Weight
Humidity : 10%~95%
Control Panel > Monitor > Setting > Advance > Monitor > Change >
Show all List …> Stand >
BSMI,FCC (DOC), CE-B, TUV/GS, UL,CUL
Net：3.25Kgs, Gross： 5.05Kgs
For 1024 ×768, please set to “XGA 1024 × 768@75Hz”
Display Modes
Mode
Resolution
H Freq (KHz)
31.469
31.469
37.861
37.500
31.469
35.156
37.879
48.077
46.875
48.363
56.476
60.023
V Freq (Hz)
1
2
640 × 350
640 × 480
640 × 480
640 × 480
720 × 400
800 × 600
800 × 600
800 × 600
800 × 600
1024 × 768
1024 × 768
1024 × 768
70.070
59.940
72.809
75.000
70.087
56.250
60.317
72.188
75.000
60.004
70.069
75.029
3
4
5
6
7
8
9
10
11
12
ViewEra V140 Rev. 1.1
CWS4UMB50031
Page 17
Page 16
|