Quick Start
Quick Reference Setup Guide
CLUB-6800
This quick reference guide is provided to help you set up your
CLUB-6800 system for the first time. It contains instructions
on setting up the products that are included in the CLUB-
6800. If you are connecting any additional gear that is not
included in the CLUB-6800, refer to the appropriate manuals
for detailed instructions.
Gathering Package Contents
The first step to putting together your new CLUB-6800 system is unpacking all of the necessary equipment. Remem-
ber to keep your manuals nearby when setting up, as you may need to reference them. The products listed below are
included in the CLUB-6800 system:
CDG-9000 PRO
• [1] Instruction Manual
SS-88 Speaker Stands
• [2] SS-88 speaker stands
KJM-8000 PRO Digital Key Control Karaoke Mixing Board
• [1] Instruction Manual
CLUB-8 Road Case
• [1] CLUB-8 road case
• [1] Rolling cart
• [2] MK-38 PRO microphones
• [1] Gooseneck DJ light
• Rack-mounting screws
VP-600 PRO 600W Professional Power Amplifier
• [1] Instruction Manual
VX-15 Vocal Speakers
• [2] VX-15 speakers
Mounting components into the CLUB-8
Below is one way to configure your CLUB-6800:
Follow these basic guidelines when mounting:
• Always screw in the mounting screws using an “X” forma-
tion.
• If possible, to keep the products cooler, leave some space in
between the components in the rack.
1
3
4
CDG-9000 PRO CONTROLLER
KJM-8000 PRO MIXER
2
CDG-9000 PRO PLAYER
VP-600 PRO AMPLIFIER
On the web at www.vocopro.com
or call toll free 1-800-678-5348
CDG-9000 PRO player unit to KJM-8000 PRO
2
You have the option of either connecting each deck of the CDG-9000 PRO separately (Fig. 1) or together through a single
SWITCHED output (Fig. 2).
Separately through individual deck outputs (Fig.1)
Using RCA cables:
1. For each deck, connect the L/R (red & white) audio outputs and Video (yellow) output on the CDG-9000 PRO to the
CDG(1) and DVD(3) inputs on the rear panel of the KJM-8000 PRO
CDG-9000 PRO Player
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
CDG-9000 PRO Player
LD(3)
LD(3)
Together through SWITCHED output (Fig. 2)
Using RCA cables:
1. Connect the L/R SWITCHED audio and
SWITCHED video outputs on the CDG-9000
PRO player to the CDG(1) audio input on the
KJM-8000 PRO
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
LD(3)
KJM-8000 PRO to VP-600 PRO
3
You can do this using either XLR(f) to XLR(m) cables or XLR(f) to ¼”(m) cables. Below are instructions for each.
Using two XLR(f) to XLR(m) (Fig.1)
Using two XLR(f) to ¼”(m) (Fig. 2)
1. Connect the XLR(f) end to the LEFT MASTER AUDIO
XLR output on the KJM-8000 PRO and the XLR (m) end
to the left XLR audio input on the VP-600 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000 PRO and
the right XLR audio input on the VP-600 PRO
1. Connect the XLR(f) end to the LEFT MASTER AUDIO XLR
output on the KJM-8000 PRO and the ¼”(m) end to the CH.
B ¼” audio input on the VP-600 PRO.
2. Now do the same thing except now go from the RIGHT
MASTER AUDIO XLR output on the KJM-8000 PRO and the
CH. A ¼” audio input on the VP-600 PRO.
BRIDGED
OUTPUTS
BRIDGED
OUTPUTS
STEREO 300W
STEREO 300W
PER CHANNEL
PER CHANNEL
INTO
4
OHM
INTO
4
OHM
BALANCED
VP-600 PRO Amplifier
KJM-8000 PRO Mixer
600W MONO
BRIDGED INTO
BALANCED
600W MONO
BRIDGED INTO
8
OHM
8
OHM
CH.
B
CH.
A
MONO
CH.
B
CH.
A
CH.
B
CH.
A
MONO
CH.
B
CH.
A
MONO
BRIDGE
STEREO
MONO
BRIDGE
STEREO
INPUTS
MODEL VP-600 PRO
INPUTS
MODEL VP-600 PRO
CDG(1)
DVD(2)
CDG(1)
DVD(2)
LD(3)
LD(3)
VP-600 PRO to VX-15 speakers
4
VP-600 PRO Amplifier
Using two 9’ MDP (Banana Plug) to ¼” speaker cables
1. Connect the MDP end to CH.B on the rear panel of the
VP-600 PRO and
BRIDGED
OUTPUTS
STEREO 300W
PER CHANNEL
INTO OHM
4
BALANCED
600W MONO
BRIDGED INTO
8
OHM
CH.
B
CH.
A
MONO
CH.
CH.
MONO
BRIDGE
STEREO
2. Connect the ¼” end to one of the two VX-15’s.
3. Repeat this for the second speaker, except now connect
the MDP end to CH. A on the VP-600 PRO.
INPUTS
MODEL VP-600 PRO
VX-15 Speaker #1
VX-15 Speaker #2
Connecting Microphones to the KJM-8000 PRO
5
Using either a mic cable with two XLR ends (Fig. A) or an XLR to ¼” cable (Fig. B):
Connect the microphone cables to the MIC inputs on the rear panel of the KJM-8000 PRO.
CDG(1)
DVD(2)
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
LD(3)
LD(3)
Adding the VSP-M1 to the CLUB-6800 system
6
Using either a mic cable with two XLR ends or an XLR to ¼” cable:
1. Connect the XLR(f) end to the LEFT BALANCED OUTPUT on the rear panel of the VSP-M1.
2. Connect the XLR(m) or ¼” end to MIC input 1 on the rear panel of the KJM-8000 PRO.
3. Follow the above steps, now going from the RIGHT BALANCED OUTPUT on the VSP-M1 to MIC input 2 on the rear panel
of the KJM-8000 PRO.
4. Connect the mics to the mic inputs on the rear panel of the VSP-M1.
VSP-M1 Processor
CDG(1)
DVD(2)
KJM-8000 PRO Mixer
LD(3)
|