Everyday
Fabric Steamer
MODEL SF-510
Owner’s Guide
Please read all instructions before use.
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.
10. Do not use unit where aerosol-based products are being used, or where oxygen is being
administered.
11. Unit is only meant to be used with recommended Everyday Fabric Steamer (model SF-510)
accessories. Using other types of attachments may cause damage to unit or injury.
12. If Lighted On/Off Switch does not illuminate when unit is plugged in and switch is set to “I”
(on) position, unit is not operating normally. Immediately disconnect cord from power supply,
then refer to troubleshooting guide on Page 13 of this manual for assistance.
13. Do not attempt to use unit without properly filling Water Tank / Water Reservoir.
14. When filling unit, only water should be used – other cleaning agents could damage unit or
cause injury. Distilled or de-mineralized water is highly recommended, in order to minimize
potential build-up of mineral deposits.
15. To reduce risk of contact with hot water emitting from Steam Nozzle, check appliance before
each use by positioning it away from body and turning it on. Do not operate unit if Steam
Nozzle is blocked.
16. Use caution when carrying unit up stairs or over obstacles, or when using unit on or near an
uneven surface.
17. Burns can occur from touching hot plastic parts, hot water, or steam. Do not touch Steam
Nozzle or attempt to connect any accessories while unit is in use. Use caution when you turn
unit upside-down – there may be hot water inside.
18. When steaming any fabric for the first time, it is recommended that you consult the
manufacturer’s guidelines for the material being steamed. For items in question, test on an
inconspicuous area before proceeding.
19. Synthetic materials (such as 100% nylon or polyester) are sensitive to heat, and my be
damaged by exposure to hot steam. Steam is recommended for use only on natural fibers
such as cotton, linen or wool, as well as nylon or polyester blends.
20. Do not allow power cord to touch hot surfaces during use. Loosely wrap cord around Cord
Wrap when storing.
21. Always allow Everyday Fabric Steamer to cool (15 minutes for complete cooling) and empty
Water Tank and Water Reservoir before storing.
SAVE THESE INSTRUCTIONS!
FOR HOUSEHOLD USE ONLY
Questions or comments?
1-800-711-6617
•
•
•
Speak your mind! You are invited to review this product online:
|
ENGLISH
3
Product Information
The following features and accessories are included with your Everyday Fabric Steamer. Carefully
inspect the packing material for all parts listed below. To obtain possible missing parts, refer to
Product Support on Page 14 of this manual for Consumer Service contact information.
UNIT FEATURES & ACCESSORIES
1
2
Steam Nozzle
Pole Top
2a Hanger Anchor Holes
2b Clothes Hanger Hooks
2c Steam Nozzle Cradle
3
4
Handle
Hose
4a Hose Base
5
Telescopic Pole
5a Pole Base
6
Water Tank
6a Valve Cap
7
8
9
Water Reservoir
Lighted On/Off Switch
Boiler (internal)
10 Cord Wrap
11 Drain Plug
12 Fabric Brush
13 Hanger
|
4
ENGLISH
The Steam Nozzle (1) emits the flow of hot, penetrating steam produced by the Boiler. The
Fabric Brush connects to the Steam Nozzle.
•
•
The Pole Top (2) connects to the top section of the Telescopic Pole. The Pole Top is comprised
of the Steam Nozzle Cradle and Clothes Hanger Hooks, and includes the Hanger Anchor Holes.
The Hanger Anchor Holes (2a) serve as the connection point for attaching the included Hanger.
The Clothes Hanger Hooks (2b) are included as an alternative to the included Hanger. The
Clothes Hanger Hooks can support garments hung from any clean rust-free hanger.
The Steam Nozzle Cradle (2c) provides a safe and convenient place to hang the Steam Nozzle
when not in use.
•
•
•
The Handle (3) is engineered to stay cool while providing maximum grip and comfort.
The Hose (4) directs steam flow from the main unit to the Steam Nozzle.
The Hose Base (4a) is the threaded receptacle onto which the Hose is screwed and secured to
the front of the main unit.
•
•
•
The Telescopic Pole (5) connects to the main unit at the Pole Base. The Telescopic Pole is
divided into four sections, three of which can be extended and lowered to a variety of heights
for optimal user comfort and convenient storage.
•
The Pole Base (5a) is the receptacle into which the Telescopic Pole is inserted and secured to
the top of the main unit.
The Water Tank (6) is the container that holds water to be transferred into the Water Reservoir.
The Water Tank is removable for convenient filling, up to a maximum capacity of 46 oz (1,360 ml).
The Valve Cap (6a) regulates the flow of water between the Water Tank and the Water Reservoir,
and must be removed in order to fill the Water Tank with water.
The Water Reservoir (7) holds water before it is transferred to the Boiler and converted into
steam.
The Lighted On/Off Switch (8) powers the unit on and off. When set to the “I” (on) position, it
illuminates to provide a clear visual indication that the unit is receiving power.
The Boiler (9) is the internal heater where water transferred from the Water Reservoir is
converted into steam.
•
•
•
•
•
•
•
The Cord Wrap (10) is designed to hold the power cord when not in use, and includes space for
storing the Fabric Brush.
The Drain Plug (11) is opened to easily empty the Water Reservoir of any remaining water.
The Fabric Brush (12) connects to the Steam Nozzle and is designed to brush away particles
such as lint, hairs and loose threads.
•
•
The Hanger (13) connects to the Pole Top via the Hanger Anchor Holes. The Hanger is designed
to support garments for easy, accessible steaming, and quickly collapses for convenient storage.
•
|
ENGLISH
5
Assembling Your
Everyday Fabric Steamer
TELESCOPIC POLE
The Telescopic Pole is made up of four sections (FIGURE 1):
TOP (SECTION 1)
•
•
•
•
MIDDLE-TOP (SECTION 2)
MIDDLE-BOTTOM (SECTION 3)
BOTTOM (SECTION 4)
FIGURE 1
SECTIONS 1, 2 & 3 are adjustable in length. By using the three extension locks, these sections
may be extended or retracted in order to achieve the desired length. Refer to Adjusting Telescopic
Pole section on Page 7 for more details.
NOTE: SECTION 4 (BOTTOM) is the widest section of the Telescopic Pole. This is the
section that fits into the Pole Base.
CONNECTING TELESCOPIC POLE
2-A
1. Make sure Pole Base coupling is loosened – rotate
it counter-clockwise if necessary.
2. Look down inside Pole Base, and locate two guide
ridges (FIGURE 2-A). Align guide grooves on
Telescopic Pole (FIGURE 2-B) with guide ridges
inside Pole Base.
2-B
3. With guide grooves aligned with guide ridges, insert
SECTION 4 of Telescopic Pole into Pole Base
(FIGURE 2-C).
NOTE: If you have trouble locating two guide
ridges inside Pole Base, insert SECTION 4 of
Telescopic Pole into Pole Base, then twist pole to
properly align the guide grooves and guide ridges.
4. Screw coupling clockwise to lock Telescopic Pole
in place (FIGURE 2-D). Telescopic Pole should now
be secured to the Pole Base.
2-C
2-D
FIGURE 2
|
6
ENGLISH
CONNECTING POLE TOP
1. Look at underside of Pole Top to locate two guide ridges (FIGURE 3-A).
2. Align Pole Top guide ridges with guide grooves on SECTION 1 of
Telescopic Pole.
NOTE: It is recommended to orient Pole Top so Nozzle Cradle
faces backwards towards rear of the unit.
3. Slide Pole Top onto SECTION 1 of Telescopic Pole (FIGURE 3-B).
Press down firmly until Pole Top fits securely in place.
3-A
CONNECTING HANGER
1. Locate brackets on back of Hanger (FIGURE 4-A).
2. Align Hanger with Hanger Anchor Holes on front of Pole Top.
Insert brackets into holes, then slide Hanger down to lock it
in place (FIGURE 4-B).
3-B
4-B
FIGURE 3
4-A
FIGURE 4
ADJUSTING TELESCOPIC POLE
To adjust the length of SECTIONS 1, 2 & 3 of the Telescopic Pole:
1. Release extension lock directly below SECTION 1 by swinging
hinge outward as shown. SECTION 1 can then be extended /
retracted (FIGURE 5).
2. Once SECTION 1 is at desired length, close hinge to once again
secure extension lock.
3. Repeat STEPS 1 & 2 for SECTIONS 2 & 3 of the Telescopic Pole,
using the extension lock directly below each of those sections.
NOTE: It is recommended to extend Telescopic Pole to its full
height during steamer operation; this will ensure optimal
steam flow through the Hose.
FIGURE 5
|
ENGLISH
7
Assembling Your
Everyday Fabric Steamer
CONNECTING HOSE
1. Place end of Hose onto threaded Hose Base (FIGURE 6-A).
2. Rotate coupling in clockwise direction until Hose is tightly secured onto Hose Base
(FIGURE 6-B). Hand tighten only. Do not over-tighten.
3. Hang Steam Nozzle on specially designed Steam Nozzle Cradle (FIGURE 6-C).
6-A
6-B
6-C
FIGURE 6
CAUTION: To prevent steam from causing bodily injury or damage to surfaces, always hang
Steam Nozzle on Steam Nozzle Cradle when not in use. Do not lay Hose on the floor as
condensation may build up, causing unwanted water droplets in the steam. Do not pull on
the Hose with excessive force as this may damage it, resulting in a steam leak.
CONNECTING FABRIC BRUSH
1. Make sure Lighted On/Off Switch is set to “O” (off) position, and that unit is not emitting any steam.
CAUTION: Do not try to connect Fabric Brush while unit is emitting steam, as this can
cause burns and injury.
2. Align Fabric Brush with Steam Nozzle as shown (FIGURE 7).
3. Press Fabric Brush firmly onto Steam Nozzle. The two pegs will fit into the two larger holes on
face of the nozzle, while latch fits over top of the nozzle (FIGURE 7-A).
7-A
Your new SF-510 Everyday Fabric Steamer
is now fully assembled and ready for use.
Please continue reading this manual for
instructions on using the Everyday Fabric
Steamer, as well as directions for proper
cleaning, storage and troubleshooting.
FIGURE 7
|
8
ENGLISH
Using Your
Everyday Fabric Steamer
FILLING WITH WATER
1. Remove Water Tank from main unit.
2. Holding Water Tank upside-down, unscrew and remove Valve Cap by rotating it in a counter-
clockwise direction (FIGURE 8-A).
3. Fill Water Tank with water through Valve Cap hole. At full capacity, the Water Tank holds 46 oz
(1,360 ml) of water, and will provide a continuous steam time of approximately 50 minutes.
For quick steaming tasks, a smaller amount of water can be used.
NOTE: In order to minimize potential mineral build-up and prolong the life of your
Everyday Fabric Steamer, distilled or de-mineralized water is recommended.
CAUTION: Only water should be used in unit – other chemicals or cleaning agents may
cause internal damage. Do not attempt to substitute any other water tank for the one
designed for use with this unit.
4. Replace Valve Cap by rotating it in a clockwise direction.
5. Place Water Tank back onto main unit (FIGURE 8-B). The sound of water flowing from Water
Tank into Water Reservoir should be audible for a short period of time.
NOTE: Water Tank can be removed and refilled at any time during operation – there is no
need to turn unit off or allow any cooling period.
IMPORTANT: Do not attempt to operate unit with an empty Water Tank.
8-B
8-A
FIGURE 8
|
ENGLISH
9
Using Your
Everyday Fabric Steamer
GENERAL OPERATION
NOTE: Be sure that Water Tank has been filled and, if desired, the Fabric Brush is
connected before following these steps.
1. For first-time use, remove protective plastic cover that is shipped on electrical plug. Plug
power cord into a convenient electrical outlet.
CAUTION: This unit uses a polarized electrical plug, with one prong that is larger than
the other. This plug will fit into a wall outlet only one way. If the plug does not correctly
fit in the outlet, contact a licensed electrician to install a proper outlet. Do not attempt to
alter plug or circumvent this safety feature in any way.
2. Set Lighted On/Off Switch to “I” (on) position, and verify that switch is illuminated.
3. After approximately 45 seconds of heating time, unit will begin producing a flow of steam from
Steam Nozzle.
NOTE: It is common for the unit to produce gurgling sounds and small amounts of water
during the first few minutes of steaming. This is due to water condensation inside cold
Hose, and should be reduced as the Hose heats up.
4. Once steam flow is steady and excess condensation has been removed from Hose, you may
proceed with your steaming tasks. Refer to Fabric Steaming section on Page 11 for more
information about steaming garments and other fabrics.
CAUTION: Always be sure that Steam Nozzle is pointed in a safe direction (away from
yourself, other people, pets and plants) when steaming.
5. When you are finished using the Everyday Fabric Steamer, immediately set Lighted On/Off
switch to “O” (off) position and unplug power cord from electrical outlet. Refer to Storage &
Care on Page 12 for proper cleaning and storage procedures.
|
10 ENGLISH
FABRIC STEAMING
STEAMING GARMENTS:
1. To expand Hanger for use, fold the two arms upward
until the lower support arms line up straight (FIGURE 9-A).
Slide lock to secure arms in place (FIGURE 9-B).
A garment may now be placed on the Hanger.
2. Alternatively, place garment on a clean, rust-free
clothes hanger. Place hanger (with garment) on one of
the Clothes Hanger Hooks (FIGURE 10).
9-A
CAUTION: Use care when handling garments hanging
on unit. Pulling on the garment with too much
force may cause the unit to tip over.
3. Direct Steam Nozzle towards bottom of garment.
Steam will rise along inside and outside of fabric,
removing wrinkles. Slowly slide Steam Nozzle
vertically, from bottom to top of garment (FIGURE 11).
9-B
FIGURE 9
NOTE: Do not allow kinks to form in Hose at any
time during use.
4. Direct Steam Nozzle away from garment and smooth
fabric with your free hand.
5. Repeat STEPS 3 & 4 as necessary until fabric is
fresh and wrinkle-free.
GENERAL STEAMING TIPS:
For most effective results, hold Steam Nozzle within
1/2” of fabrics, or press it directly against surfaces.
Curtains and draperies can be steamed while still hanging.
To remove wrinkles from towels, handkerchiefs and
napkins, drape them over a rod or towel rack and gently
steam them.
•
•
•
FIGURE 10
Heavier fabrics may require repeated steaming to
achieve desired results.
To remove exceptionally stubborn wrinkles, steam both
sides of fabric.
Be especially careful when steaming any delicate fabrics
that may be damaged by heat or water spotting.
To sanitize a fabric, hold Steam Nozzle within 1/2 inch
of a single area for at least 5 seconds. Use caution
when doing this on more delicate fabrics.
•
•
•
•
To remove particles like lint, hairs and loose threads,
connect the Fabric Brush to the Steam Nozzle.
•
FIGURE 11
|
ENGLISH 11
Storage & Care
PROPER STORAGE
Preparing your Everyday Fabric Steamer for storage is quick and simple. When you have finished
your steaming tasks, follow the steps listed below.
1. Set Lighted On/Off Switch to “O” (off) position, and unplug power cord from electrical outlet.
2. Allow unit to cool (15 minutes for complete cooling).
3. Bring unit to a convenient sink or tub.
4. Remove Water Tank from unit. Unscrew Valve Cap and drain all remaining water from Water
Tank. Replace Valve Cap when finished.
5. Open Drain Plug and drain all remaining water from Water Reservoir to prevent overfilling during
your next use. Securely replace Drain Plug and place empty Water Tank back onto main unit.
6. For storage convenience, you may wish to collapse Telescopic Pole to its most compact height
(refer to Page 7 for details).
7. Place Fabric Brush in storage compartment inside Cord Wrap, and wrap power cord around
Cord Wrap. Store Everyday Fabric Steamer in a cool dry location.
CARE & MAINTENANCE
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. The best way to minimize mineral build-up is
to use distilled or de-mineralized water during every use of your Everyday Fabric Steamer.
If distilled or de-mineralized water is unavailable, regular tap water may be used. However, the
resulting mineral build-up may limit the effectiveness and reduce the overall life of your Everyday
Fabric Steamer. To prevent this, it is recommended to de-mineralize the boiler after 30-40 uses
using Steamfast Lemon Acid.
To remove mineral build-up:
1. Set Lighted On/Off Switch to “O” (off) position and unplug power cord from electrical outlet.
2. Allow unit to cool (15 minutes for complete cooling).
3. Bring unit to a convenient sink or tub.
4. Remove Water Tank from unit. Unscrew Valve Cap and drain all remaining water from Water Tank.
5. Open Drain Plug and drain all remaining water from Water Reservoir. Securely replace Drain Plug.
6. Mix one packet of Steamfast Lemon Acid in 8 oz (236 ml) of warm tap water, and stir solution
until dissolved. CAUTION: Only Steamfast Lemon Acid should be used in the Everyday
Fabric Steamer. Pour solution into Water Tank, and replace Valve Cap. Place Water Tank
back onto main unit.
7. Plug power cord into an electrical outlet and set Lighted On/Off Switch to “I” (on) position.
Allow unit to steam until the Water Tank is emptied. CAUTION: Do not allow unit to continue
running with an empty Water Tank. Set Lighted On/Off Switch to “O” (off) position and allow
unit to cool for a minimum of 10 minutes.
8. Open Drain Plug and drain any remaining cleaning solution from Water Reservoir. CAUTION:
Leftover solution may still be hot. Securely replace Drain Plug.
9. Pour 8 oz (236 ml) of warm tap water into Water Tank and place tank onto main unit. Open
Drain Plug and drain water from unit, then securely replace plug.
10. When finished, unplug power cord from electrical outlet. Continue with normal storage
procedure, as outlined in Proper Storage section above.
|
12 ENGLISH
Product Support
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
Unit is not plugged in.
SOLUTION
Unit fails to heat up. Lighted On/Off
Switch DOES NOT illuminate when
set to “I” (on) position.
Plug power cord into electrical outlet.
Household circuit breaker / ground
fault interrupter has tripped or blown interrupter, or replace fuse. For
Reset circuit breaker / ground fault
a fuse.
assistance, contact a licensed electrician.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
assistance (see below for details).
Unit fails to heat up. Lighted On/Off
Switch DOES illuminate when set to
“I” (on) position.
No water in unit.
Refer to Filling With Water procedure
on Page 9 to fill unit with water.
Mineral build-up in unit.
Refer to Care & Maintenance
NOTE: Always allow sufficient
time for unit to heat up and begin
producing steam.
section on Page 12 for details.
Unit is damaged or otherwise in
need of repair.
Immediately cease usage and unplug.
Contact Consumer Service for
assistance (see below for details).
Excessive gurgling in Hose and
Steam Nozzle / water drips from
Steam Nozzle.
Condensation build-up inside of
Steam Nozzle / Hose.
Some gurgling is a natural effect of
the steaming process. For excessive
gurgling or dripping water, point Steam
Nozzle downward and shake thoroughly
to remove excess water droplets.
Mineral build-up in unit.
Refer to Care & Maintenance
section on Page 12 for details.
Steam output is weak or intermittent. Water level in Water Reservoir is
running low.
Refer to Filling With Water procedure
on Page 9 to refill unit with water.
Mineral build-up in unit.
Refer to Care & Maintenance
section on Page 12 for details.
CONSUMER SERVICES
For problems with your Everyday Fabric Steamer, please refer to the troubleshooting guide
located above. Additional inquiries should be directed to our consumer support services through
If you do not have internet access, you may also contact our Consumer Service Department by
telephone, at 1-800-711-6617.
NOTE: In order for our Consumer Service representatives to help you as quickly and
efficiently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number (located near electrical specification label on bottom of unit)
• Date code (4-digit number located on electrical specification label on bottom of unit)
For information regarding your 1 year limited warranty, refer to Page 15 of this manual.
|
ENGLISH 13
Product Support
REPLACEMENT ACCESSORIES
When ordering replacement accessories for your Everyday Fabric Steamer, you may refer to the
part numbers below. Replacement accessories may be ordered through our Web site:
You may also contact Consumer Service directly:
FABRIC BRUSH
HANGER
A510-001R-
A510-002R-
NOTE: Due to continuing improvements, part numbers listed above may change.
For assistance ordering parts, please contact Consumer Service directly.
PRODUCT SPECIFICATIONS
SF-510
MODEL
VOLTAGE
120V
1500W
WATTAGE
12.5A
AMPERAGE
46 OZ (1,360 ML)
WATER CAPACITY
HEATING TIME
45 SEC (APPROXIMATE)
50 MIN (APPROXIMATE)
10.82 LBS (4.91 KG)
11.0” (27.9 CM) x 11.5” (29.2 CM) x 63.0” (160.0 CM)
6.2’ (190.0 CM)
CONTINUOUS STEAM TIME
UNIT WEIGHT
UNIT DIMENSIONS
POWER CORD LENGTH
|
14 ENGLISH
Warranty Information
1 YEAR LIMITED WARRANTY
Steamfast, a division of Vornado Air LLC, (“Steamfast”) warrants to the original consumer or purchaser
this Steamfast Everyday Fabric Steamer SF-510 (“Product”) is free from defects in material or workmanship for
a period of one (1) year from the date of purchase. If any such defect is discovered within the warranty
period, Vornado, at its discretion, will repair or replace the Product at no cost if the Product is returned
to Steamfast postage-paid. Repairs not covered by the warranty or outside the warranty period will
require a fee to cover the cost of materials, handling and shipping.
This warranty does not apply to defects resulting from abuse of the Product, modification, alteration,
repair or service of the Product by anyone other than Steamfast, mishandling, improper maintenance,
commercial use of the Product, damages which occur in shipment or are attributed to acts of God.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. STEAMFAST SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BYAPPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may have other rights that vary from state to state.
For warranty or repair service, call 1-800-711-6617 or email [email protected] to obtain
a Return Authorization (“RA”) form. Please have or include your Product’s model number, date code and
serial number, as well as your name, address, city, state, zip code and phone number when contacting
Steamfast for warranty service. You may be required to provide the original sales receipt. For your
records: Staple or attach your original sales receipt to this Owner’s Guide. Please also write your
Product’s serial number below (located on product specs decal).
Serial No. __________________________________________________________________________
After receiving the RA form, ship your Product to:
Steamfast
Attn: Warranty & Repair
6655 Troost Avenue
Kansas City, MO 64131
To assure proper handling, packages must be clearly marked with the RA number. Packages not
clearly marked with the RA number may be refused at the receiving dock.
Please allow 1-2 weeks for repair and return of your Product after the Product is received.
© 2011 Vornado Air LLC • Andover, KS 67002
Specifications subject to change without notice.
Steamfast® is a trademark owned by Vornado Air LLC.
Manufactured in China.
Steamfast Consumer Service
|
P: 1-800-711-6617
|
|
ENGLISH 15
review this product online
evalúe este producto en línea
évaluer ce produit en ligne
Steamfast
415 East 13th, Andover, KS 67002
V110512
|