1
3
G2 cradle DCR-300/DCR-50 contents
Disclaimer and warranty
Important disclaimer, please read!
Compatible iPod & iPhone
Unauthorized reproduction or reverse engineering is strictly prohibited! Intellectual property included is distributed under specific license
agreement with respective owners and is licensed only, not sold. No warranty, explicit or implied, is stated. Neither DICE Electronics, LLC., nor
any of its agents, distributors, dealers or vendors shall be liable for damages.
IN NO EVENT SHALL DICE ELECTRONICS' LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING
SOFTWARE OR ITS DOCUMENTATION.
For internal use only. Do not submerge or expose to water or other fluids. DICE G2 cradle is NOT water proof and it will be damaged by water.
You must properly insulate its casing if your installation environment may subject the unit to water, such as a convertible vehicle.
Keep away from children! DICE G2 cradle can be broken, or disassembled, and components may become loose from vibration and heat.
Small components and packaging materials may become choking hazard when handled by children.
Warning! Never place any objects directly into the path of an airbag. DICE Electronics does not accept any responsibility for any damage or
injury as a result of using this product. Exercise good judgment and keep your eyes on the road at all times!
DICE logo is a trademark of DICE Electronics, LLC. Kuda is a trademark of KUDA Group. iGrip is a trademark of HR GmbH & Co. KG. ProClip
is a trademark of ProClip USA Inc. The Made for iPod logo is a trademark of Apple Inc. The Works with iPhone logo is a trademark of Apple Inc.
Apple iPod is not included in the package.
DICE G2 cradle
Universal 5V Cradle for iPod and iPhone
Model: DCR-50-PTH
Installation Guide/User Manual
Table of contents
Disclaimer and warranty ......................................1
Compatible iPod & iPhone ...................................2
G2 cradle contents ...............................................3
Choose the correct holder ....................................4
Installation ............................................................5
Mounting option ....................................................6
Connect the cradle ...............................................7
Long base installation ...........................................8
Adjusting the angle ...............................................9
DCR-300/DCR-50 cradle
with regular base and
iPhone 4 holder x1
additional holders x6
long base x1
Warranty and Support
If you experience any problems or need help, please contact you local dealer or call DICE Electronics, LLC. At 888-342-3999 or visit us at
Products carry a 1 year limited warranty that protects you from defects in material and workmanship of products sold by DICE Electronics or its
authorized agents, distributors and dealers. The warranty period begins the day a product is purchased by the end user. Products found to be
defective during the warranty period will either be repaired or replaced by DICE Electronics at no charge unless warranty is void. Unauthorized
attempt of repair or alteration of the product in any way immediately voids this warranty. Warranty does not extend to cosmetics or finish. A DICE
product specialist must determine that a defect is present in the product and issue an RMA. Be sure that all wiring is connected as described
in the user manual and all related equipment is functioning properly. DICE Electronics disclaims any liability for other incurred damages
resulting from product defects. Any expenses in the removal and reinstallation of products are not covered by this warranty.
PLEASE NOTE: International customers requiring a product replacement, please contact the dealer your product was purchased from!
4
mounting screws x4
DCR-300/50 REV. 080510
6
5
4
Mounting option
Installation
These holes are designed to allow you to
Choose the correct holder
screw the cradle base to AMPS standard
mounts (ProClipTM, KudaTM, etc).
Compatible iPhone/iPod model can be found here.
Slide the correct holder
onto the cradle until it
clicks.
Slide the iPhone/iPod
into the holder
0609r1
Each holder is designed for a different
iPhone/iPod model. Identify the holder
by the printed text on the back of the
holder and choose the correct holder
for your iPhone/iPod.
Use the screws (x4) in the package
to screw the cradle to AMPS
standard mounts.
These holes are designed to fit
vehicle mounts from iGripTM.
7
8
9
Connect the Cradle
Long base Installation
Adjusting the angle
To adjust the angle of the cradle, please
loosen the set screw enough for the cradle
to move freely. When you are done
adjusting the angle, hold the base and
tighten the set screw. DO NOT OVER
TIGHTEN!
Attach the iPod dock
cable into the
connector on the back
of the cradle
If the long base will fit your car interior more appropriately than the short one,
then please follow the illustration to attach the long base to the cradle. Turn the
base clockwise to tighten the base to the cradle.
cable connects
facing down
(back view)
(front view)
Marking is on the bottom side!
|