XDM7615
INSTALLATION/OWNER'SꢀMANUAL
AM/FM/CD/MP3/WMAꢀReceiverꢀ
withꢀ2-StepꢀMotorizedꢀDetachableꢀFace
XDM7615ꢀINSTALLATIONꢀ
WiringꢀDiagram
Antenna Connector
BLACK
Front Preamp Output
Steering Wheel Interface Input
BLUE
PAC SWI-PS required
Subwoofer Preamp Output
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XDM7615 uses one
10 amp ATM fuse located
beside the wiring connector.
3
XDM7615ꢀOPERATION
ControlꢀLocationsꢀ-ꢀReceiver
6
12
1
2
3
5
10 11
4
7
8
9
21 20 19
15
14
16
13
18
17
Eject
Tune/Track Up
Mode/Search
Audio/Setup
EQ
1
2
12
13
14
15
16
17
18
Auxiliary Input
Open
3
AS/PS/Enter
Band
4
Mute
5
Scan
Preset 1/Repeat
6
Display
Preset 4/Play/Pause
Preset 2/Random
Preset 5/Folder Down
Preset 3/Intro
7
19 Reset
8
20
21
Power
Tune/Track Down
9
10
11
Preset 6/Folder Up
4
XDM7615ꢀOPERATION
ControlꢀLocationsꢀ-ꢀRemote
1
2
3
4
5
6
21
7
8
9
20
19
18
17
10
11
12
13
16
15
14
Mode/Search
Volume Up
Power
1
2
Scan
12
13
14
15
16
Loudness
Open
3
Audio/Setup
Tune/Track Up
Volume Down
AS/PS/Enter
4
Display
Mute
5
6
17 Preset 5/Folder Down
18
19 Preset 1/Repeat
7
Preset 4/Play/Pause
Preset 2/Random
Preset 3/Intro
Preset 6/Folder Up
EQ
8
9
Band
20
21
10
11
Tune/Track Down
5
XDM7615ꢀOPERATION
GeneralꢀOperation
With the unit off, press EJECT to allow the front panel to
FrontꢀPanelꢀRemoval
slide down. Gently squeeze the release tab located on the
bottom center underside and pull front panel down and away
from unit to remove. To install, insert left side first, then
push right side to secure.
Press POWER or any other button (except EJECT or OPEN) to
PowerꢀOn/Off
Mode
turn the unit on. Press POWER to turn the unit off.
Press MODE to select between AM/FM, CD player and
auxiliary input. Modes of operation are shown in the display.
NOTE: CD mode will not appear unless a CD is inserted.
Insert a 3.5mm connector into the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
MODE to select AUX mode.
AuxiliaryꢀInput
The steering wheel interface input located on the back of
the head unit allows connection to the PacificꢀAccessoryꢀ
Corporationꢀ(PAC)ꢀSWI-PS interface module (sold separate-
SteeringꢀWheelꢀInterfaceꢀ
Input
To configure steering wheel controls, follow the instructions
provided with the PACꢀSWI-PS interface module. After
installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Adjust volume using rotary encoder (00-46).
Volume
Press and hold POWER for 2 seconds to program currently
selected volume level. "P-VOL" and the current volume level
will momentarily appear in the display.
Programmableꢀ
Turn-OnꢀVolume
Press EQꢀto select between POP, JAZZ, CLASSIC, BEAT,
ROCK and OFF (default) equalization curves. Any adjustment
to the Bass or Treble settings automatically cancels the
current EQ curve (if one is selected).
PresetꢀEQꢀCurves
Press DISP to select between clock and different types of
information, such as radio frequency, CD track/elapsed time
or MP3/WMA song information.
Display
Reset
Press RESET upon initial installation or if abnormal
operation occurs. Reset button is located on the front panel.
6
XDM7615ꢀOPERATION
GeneralꢀOperationꢀ-ꢀSetupꢀMenu
SetꢀtheꢀClock With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE
to adjust the hours
to adjust the minutes. Press DISP momen-
nn
and TUNEꢀ
ll
tarily to save the selected time.
12/24-hourꢀClockꢀ The clock will display 12-hour AM/PM time in USA
:
frequency spacing mode (PM 10 00). In European frequency
spacing mode, the clock will display 24-hour time (22:00).
Press and hold SETUP for more than 3 seconds to access
the setup menu. Press SETUP momentarily to select
between the menu functions and rotate the rotaryꢀencoder
left/right to adjust or activate the desired function.
SetupꢀMenu
MenuꢀFunction
Options
Action
LoudnessꢀCurve LOUD OFF Disables the loudness function.
LOUD ON Enables the loudness function. Activating this feature
will enhance the bass and treble frequencies when
listening to music at low volumes.
TunerꢀFrequencyꢀ FREQ USA Programs the unit to USA tuner spacing.
Spacing
(200kHz for FM and 10kHz for AM)
FREQ EUR Programs the unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
ClockꢀDisplay
CLK OFF
Programs the unit to not display the clock when the
power is off.
CLK ON
Programs the unit to display the clock when the power
is off.
AuxiliaryꢀMode
AUX ON
Enables access to auxiliary mode.
Disables access to auxiliary mode.
Disables the confirmation beep.
AUX OFF
BEEP OFF
BEEP ON
LOC OFF
LOC ON
Beepꢀ
Confirmation
Enables the confirmation beep.
Local/Distanceꢀ
Tuning
Activates Distance tuning.
Activates Local tuning for strong station reception only.
SubwooferꢀMode SB-W OFF Disables the subwoofer RCA output.
SB-W ON
Activates the subwoofer RCA output. Subwoofer control
will be available in the audio menu.
Powerꢀonꢀ
Message
MSG OFF
MSG ON
DEMO ON
Disables power on message.
Enables power on message to be displayed.
Enables the "BT READY AND IPOD READY" message.
Demonstrationꢀ
Mode
DEMO OFF Disables the demonstration mode.
7
XDM7615ꢀOPERATION
GeneralꢀOperation
Audio
Press AUDIO momentarily to select between Volume
(default), Bass, Treble, Balance, Fader and *Subwoofer.
VOLUME
BASS TREBLE
BALANCE
FADER
*SUBWOOFER
Bass
Treble
Press AUDIO until BAS appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Press AUDIO until TRE appears then rotate encoder
left/right to adjust ( -6 minimum / +6 maximum).
Balance
Press AUDIO until BAL appears then rotate encoder
left/right to adjust (BAL L 12-BAL 00-BAL R 12).
BAL 00 represents equal balance
Fader
Press AUDIO until FAD appears then rotate encoder
left/right to adjust (FAD F 12-FAD 00-FAD R 12).
FAD 00 represents equal fader
Subwoofer
Press AUDIO until SUB appears then rotate encoder
left/right to adjust (0 minimum / +12 maximum).
Note:ꢀ
Subwoofer option must be enabled before it will appear in
the audio menu. Refer to page 7 for details.
SourceꢀAudioꢀMemory Individual Bass and Treble settings are retained in memory
for AM, FM, CD or AUX modes. This allows you to save the
Bass and Treble settings separately for each mode.
Note:
Any adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
8
XDM7615ꢀOPERATION
AM/FMꢀTunerꢀOperation
SeekꢀTuning
Press TUNE
or TUNEꢀ
momentarily to seek the
nn
ll
next strong station.
ManualꢀTuning
Press TUNE
or TUNEꢀ
for more than 2 seconds,
nn
ll
then release. "MANUAL" will momentarily appear in the
display. Press TUNE
or TUNEꢀ
momentarily to
nn
ll
move radio frequency up or down one step at a time. Press
and hold to advance quickly. If tuning is not adjusted for 5
seconds, the unit will return to seek tuning mode (default).
"AUTO" will momentarily appear in the display.
ScanꢀTuning
Bandꢀ
Press SCAN to preview strong stations on the current band,
pausing for 5 seconds at each. Press SCAN again to cancel.
Press BAND to select between FM1, FM2, FM3, AM1 and
AM2 bands.
StoringꢀandꢀRecallingꢀ
StationꢀPresets
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than
2 seconds. When stored, the preset number will appear in
the display. The station can be recalled anytime by pressing
the corresponding preset button.
Press AS/PS for more than 2 seconds to automatically store
the six strongest stations in the current band. Automatic
Local tuning is activated during the initial band scan.
AutomaticallyꢀStoreꢀ
Stations
Press AS/PS for less than 2 seconds to scan presets 1-6 on
the current band, pausing for 5 seconds at each. Press
AS/PS again to cancel.
PresetꢀScan
9
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperation
InsertꢀCD Press EJECT to access the CD slot. With the label facing
up, insert a standard size CD into the CD slot. The CD will
automatically begin playback.
EjectꢀCD Press EJECT to eject the CD. The unit will change to
previous mode of operation (AM, FM or auxiliary input).
If the disc is not removed within 10 seconds, the unit will
reload the disc. The unit does not have to be turned on to
eject CD.
TrackꢀSelect Press TRACKꢀ
to skip to the beginning of the next
ll
track. Press TRACK
current track. Pressing TRACK
beginning of the previous track.
to return to the beginning of the
nn
again skips to the
nn
FastꢀForwardꢀandꢀReverse Press and hold TRACKꢀ
or TRACK
to fast forward
ll
nn
or reverse a track.
Pause Press
/
/
II to temporarily stop CD playback.
II again to resume playback.
l
Press
l
Scan Press INTꢀto play the first 10 seconds of each track.
Press INT again to cancel.
Repeat Press RPT to continuously repeat selected track.
Press RPT again to cancel.
Random Press RDM to play all tracks in random order. Press RDM
again to cancel. Random mode is retained in memory when
selecting between AM/FM tuner, CD player and auxiliary
input modes and when the unit is turned off/on.
CD-R/CD-RWꢀCompatibility Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method. In
addition, the following CDs may be incompatible with this
unit:
CDs exposed to extreme temperatures or direct sunlight
for extended periods of time, CDs recorded in which a
recording session failed or a re-recording was attempted
and, or encrypted or copy-protected CDs which do not
conform to the audio CD-DA red book recording standard.
10
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
PlayingꢀanꢀMP3/WMAꢀDisc When an MP3/WMA encoded disc is first inserted,
“READING” will appear in the display. Depending on the
number of files and folders, this may take several seconds.
DisplayingꢀInformation Press DISP to select between track number/elapsed time
(default), clock, track name, directory name, title, artist and
album.
“NO ID3 TAG” will be displayed if the MP3 file contains no
ꢀꢀ
ID3 tag information.
“UNKNOWN” will be displayed if the WMA file contains no
WMA tag information.
“ROOT” will be displayed if the directory name of a root
folder is not labeled.
ꢀTitleꢀIconꢀꢀ
ArtistꢀIconꢀꢀ
AlbumꢀIconꢀꢀ
FolderꢀIconꢀꢀ
This icon will illuminate when the song title is displayed.
This icon will illuminate when the artist name is displayed.
This icon will illuminate when the album name is displayed.
This icon will illuminate when the directory name is
displayed.
CharacterꢀSupport Maximum character display information
• Track name – 32 character maximum
• Directory name – 23 character maximum
• *Song title – 30 character maximum
• *Artist name – 30 character maximum
• *Album name – 30 character maximum
*Song title, Artist Name, and Album name, will only be
displayed if included with the MP3/WMA file.
When referring to MP3/WMA playback, the following terms
are synonymous:
• File name and track name
• Folder name and directory name
11
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
Refer to the following button function table when selecting, searching or
navigating MP3/WMA files and folders:
DirectꢀFileꢀSelect
Stepꢀ1
Press SEARCHꢀfor more than 3 seconds, then release.
“MP3 T " or “WMA T ” will flash in the display. Use the
*
*
buttons in the above table (3 keystroke maximum input),
or the rotary encoder to enter the desired file number.
Stepꢀ2
Press
to confirm the selected file number or wait for
the input cycle to time out (approximately 5 seconds).
If the file is not available, “NO FILE” will be displayed
momentarily and the current file will continue to play.
File/FolderꢀNavigate
Stepꢀ1
Press SEARCHꢀfor more than 3 seconds, then release.
Press SEARCHꢀagain to navigate files/folders on the disc.
The current folder name will scroll one time followed by
available files and folders.
Stepꢀ2
Stepꢀ3
Stepꢀ4
Turn the rotary encoder to preview files/folders in the
current folder. If a folder is selected, the
icon will
illuminate.
Press
to select the desired file or folder. If a folder is
selected, "/ꢀ/ꢀ" will be displayed. Turn the rotary encoder to
the right to begin searching files in the folder.
Press
to select the desired file within the folder.
*FolderꢀAccess
(Upꢀꢀoneꢀlevel)ꢀ
When navigating folders (and “/ꢀ/“ is displayed), press AUDIO
to access the previous level (up one level).
*Only available on MP3/WMA discs recorded with more than
one folder.
12
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
NavigatingꢀNote After navigating by direct select or file/folder navigate
modes, the track number and elapsed time will be
displayed by default. Press DISP momentarily to select
clock, track name, directory name, title, artist and album.
*FolderꢀAccessꢀ Press
to select the previous folder.
to select the next folder.
Press
*Folder access is only available on MP3/WMA discs
recorded with more than one folder.
FileꢀRepeat Press RPT momentarily to continuously repeat selected file.
Press RPT again to cancel.
FolderꢀRepeat Press RPT for more than 2 seconds to consecutively repeat
all files in the current folder only. The
in the display when in folder repeat mode.
Press RPT again to cancel.
icon will appear
DiscꢀRandom Press RDM momentarily to play all files on entire disc in
random order. Press RDM again to cancel.
FolderꢀRandom Press RDM for more than 2 seconds to play all files in
current folder only in random order. The
icon will
appear in the display when in folder random mode.
Press RDM again to cancel.
DiscꢀIntro Press INT momentarily to play the first 10 seconds of each
file on the entire MP3/WMA disc. Press INT again to cancel.
FolderꢀIntro Press INT for more than 2 seconds to play the first 10
seconds of each file in the current folder only. The
will appear in the display when in folder intro mode.
Press INT again to cancel.
icon
Note:
File repeat (current folder only), folder random and folder
intro is only available on MP3/WMA discs recorded with
more than one folder.
13
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
MediaꢀCompatibility
The following types of discs/files are compatible:
• CD-ROM (ISO), CD-R, CD-RW
• CD-DA
• MP3 data
• WMA data
The following types of discs/files are not compatible:
• WMA files that are protected by DRM (Digital Rights
Management).
• WMA lossless format
• Discs recorded with Track At Once or packet writing
• MP3 PRO format
• MP3 playlists
• WAV format
PlaybackꢀOrder
MP3/WMA playback sequence is based on recorded order
of files and begins in the root folder of the disc. Any empty
folders or folders that do not include MP3/WMA files are
skipped. This unit may not play files in the order they were
recorded in. Refer to your recording software’s user’s manual
for more information.
CompatibleꢀRecordingꢀ
Formats
• ISO9660 level 1
• ISO9660 level 2
• Yellow Book MODE 1
• Yellow Book MODE 2 FORM 1
• Multi session
• Maximum folders and files - 256
• Maximum folder levels - 8
• MPEG-1/2/2.5 Audio Layer-3
ISO9660 standards:
• Maximum nested folder depth is 8 (including the root folder).
• Valid characters for folder/file names are letters A-Z
(all caps), numbers 0-9, and “_” (underscore). Some
characters may not be displayed correctly, depending on
the character type.
• This device can play back discs in Joliet, Romeo, and other
standards that conform to ISO9660. MP3/WMA written in the
formats other than the above may not play and/or their file
names or folder names may not be displayed properly.
14
XDM7615ꢀOPERATION
CDꢀPlayerꢀOperationꢀ-ꢀMP3/WMAꢀFiles
AdditionalꢀMP3/WMAꢀ
An internal buffer provides ESP (Electronic Skip Protection) to
virtually eliminate skipping.
Information
When playing a disc recorded with regular audio files
(CD-DA or .WAV) and MP3/WMA files, the unit will play the
MP3/WMA files only.
Only MP3 files with filename extension (.mp3) can be played.
Only WMA files with filename extension (.wma) can be played.
Do not attempt to play discs which contain non-MP3/WMA
files with the MP3/WMA extension.
SamplingꢀFrequencyꢀRates
MP3
8kHz ~ 48kHz
32kHz ~ 48kHz
WMA
TransferꢀBitꢀrates
MP3
32kbps ~ 320kbps constant
Variable bit rates
WMA
32kbps ~ 192kbps constant
Variable bit rates
Note:
Some files may not play or be displayed correctly,
depending on sampling rates and bit rates.
MP3ꢀTagꢀDisplay
ID3 tags Version 1.x
This model will not display ID3 Version 2.0 or greater tags.
RecommendedꢀSettings
For best results, use the following settings when burning an
MP3 disc:
128kbps or higher constant bit rate
44.1kHz or higher sampling frequency
For best results, use the following settings when burning a
WMA disc:
64kbps or higher constant bit rate
32kHz or higher sampling frequency
15
XDM7615ꢀWARRANTY
LimitedꢀOneꢀYearꢀWarranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Whatꢀtoꢀdo?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
Whoꢀisꢀcovered?ꢀThis warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
• Call us toll-free at 1-866-382-5476
• E-mail us at [email protected]
Whatꢀisꢀcovered?ꢀThis warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
16
XDM7615ꢀOPERATION
Troubleshootingꢀ
Problem
Cause
Action
Yellow wire not connected or incorrect
voltage Red wire not connected or
incorrect voltage
Check connections for proper
voltage (11~16VDC)
Unitꢀwillꢀnotꢀturnꢀonꢀ
(noꢀpower)
Black wire not connected
Fuse blown
Check connection to ground
Replace fuse
Speaker wires not connected
Check connections at speakers
Unitꢀhasꢀpowerꢀ
(butꢀnoꢀsound)
One or more speaker wires touching each Insulate all bare speaker wires
other or touching chassis ground
from each other and chassis
ground
Yellow or red wire touching chassis
ground
Check for pinched wire
Unitꢀblowsꢀfuses
Speaker wires touching chassis ground
Incorrect fuse rating
Check for pinched wire
Use fuse with correct rating
Unit is not mounted correctly or backstrap Check mounting sleeve and
is not secure
backstrap support
Excessiveꢀskipping
Physical defect in media (CD, CD-R or
CD-RW)
Check media for scratches
ERROR-01ꢀappearsꢀ
onꢀdisplay
Disc read error
Press eject or RESET
Press eject or RESET
Focus error or disc is in upside down
ERROR-02ꢀappearsꢀ
onꢀdisplay
PROTECTꢀappearsꢀ
onꢀdisplay
The WMA file is copy-protected by DRM
(Digital Rights Management)
Write disc using WMA files that
are not copy-protected
Selected file is not available in direct or
alphanumeric search modes
Repeat search using valid
parameters
NOꢀFILEꢀappearsꢀ
onꢀdisplay
The file format is incompatible
Write disc using valid audio
files with .mp3 or .wma file
extensions
INVALIDꢀappearsꢀ
onꢀdisplay
CD mechanism position out of alignment
CD transit screws still in place
Press and hold EJECTꢀfor 3
seconds to reset CD mechanism
position
Unitꢀwillꢀnotꢀacceptꢀ
aꢀdisc
Remove 2 transit screws located
on top of the unit
17
XDM7615ꢀOPERATION
Specifications
CDꢀPlayer Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1ꢀBit
FMꢀTuner Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AMꢀTuner Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General Operating voltage: 11-16ꢀVDC,ꢀnegativeꢀground
Speaker output impedance: 4~8ꢀohms
Line output voltage: 2ꢀVolts
Dimensions: 7"ꢀxꢀ7"ꢀxꢀ2"ꢀ(178ꢀxꢀ178ꢀxꢀ51ꢀmm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
18
XDM7615ꢀOPERATION
Notes
19
Dual Electronics Corp.
Toll Free: 1-866-382-5476
©2008 Dual Electronics Corp. All rights reserved.
Windows Media and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the
United States and or other countries.
Other trademarks and trade names are those of their respective owners.
NSA0608-V02
|