60 SECOND ESP PLUSTM
ELECTRONIC SHOCK PROTECTION
PROGRAMMABLE COMPACT DISC PLAYER
WITH REMOTE CONTROL
MODEL CD-855
OPERATING INSTRUCTIONS
PLAYS MUSIC COMPACT DISCS
INCLUDES WIRED REMOTE CONTROL
BASS BOOST SYSTEM
6 DIGIT LCD VISUAL DISPLAY
•
•
•
•
TRACK REPEAT & DISC REPEAT
•
60 SECOND ESP PLUSTM (ELECTRONIC SKIP PROTECTION) SYSTEM
•
DELUXE STEREO HEADPHONES INCLUDED
USES 2 SIZE “AA” BATTERIES (NOT INCLUDED)
LINE OUT JACK - CONNECTS TO YOUR STEREO SYSTEM
•
•
•
PLEASE READ CAREFULLY BEFORE USE
IB-CD855(CDX82C-60C8)-WM-E-011604
LOCATION OF CONTROLS
8
7
6
5
4
3
9
10
11
12
13
23
2
1
14
22
17
21
18
19
15
20
16
1. LCD DISPLAY
2. CD DOOR OPEN BUTTON
3. REPEAT BUTTON
4. PROG. BUTTON (for programmed play)
5. RANDOM BUTTON
6. LINE OUT JACK (for home stereo connection)
7. VOLUME CONTROL
The following controls are for the
Wired Remote Control
17. PLAY/PAUSE & POWER ON
18. STOP/OFF
19. SKIP/SEARCH BACKWARD
20. SKIP/SEARCH FORWARD
21. VOLUME CONTROL
22. BELT CLIP (at back)
23. HEADPHONES JACK
8. CD DOOR
9. PHONES JACK (headphones jack, also for
REMOTE CONTROL connection)
10. FORWARD SKIP + BUTTON
11. BACKWARD SKIP - BUTTON
12. STOP AND POWER OFF BUTTON
13. PLAY/PAUSE & POWER ON BUTTON
14. BASS BOOST SWITCH
15. BATTERY DOOR
16. AC ADAPTOR JACK (AC ADAPTOR not included)
2
IB-CD855(CDX82C-60C8)-WM-E-011604
POWER SOURCES
Power this CD player by inserting 2 size “AA” fresh alkaline batteries.
1. USING WITH BATTERIES
Insert 2 size “AA” alkaline batteries according to
the + and - markings on the bottom of the set.
NOTE: Player will not work, and batteries will be
drained, if batteries are not inserted as
shown on the bottom of the set.
TIPS ON BATTERY USE
Reversing polarities will damage the batteries and possibly your set. Be sure to
follow polarity ( + and - ) as indicated.
•
Do not mix different types together (Alkaline, Carbon-Zinc, Nickel-Cadmium etc.),
or old batteries with new ones.
•
When not in use for an extended period of time, or while internal batteries will not
be used, remove them to prevent possible acid leakage or corrosion resulting in
damage to your player.
•
When the batteries have become discharged, they must be disposed of in a safe
manner that complies with all applicable laws.
•
Installation of batteries should only be done by an adult (for safety).
•
ALKALINE BATTERY LIFE
Bear in mind that battery life expectancy is based upon volume and bass listening
levels.
Maximum battery power consumption happens at maximum settings. Typical life for 2
size “AA” alkaline batteries is above 8 hours of continuous CD play.
2. AC ADAPTOR (OPTIONAL)
You can also power this CD player by connecting an optional AC adaptor. Before you
buy an optional AC Adaptor, please note, the only AC ADAPTOR suitable for this player
is DC 4.5V 600mA (or greater), with plus center polarity
. Others may damage
your player. Please check voltage and current (mA) before buying an AC ADAPTOR.
WHEN
SHOWS IN THE DISPLAY
While the CD is playing, if the alkaline batteries are weak or discharged, this symbol
“
” shows or flashes in the display, then the power automatically turns off. If this
occurs, replace both alkaline batteries (also if the display does not show anything, the
batteries are dead).
NOTE: You may use rechargeable batteries on this set. However, because
rechargeable batteries generally have lower voltage (1.2 volts instead of
1.5 volts). Your playing time will be much less than normal fresh alkaline
batteries.
3
IB-CD855(CDX82C-60C8)-WM-E-011604
CONNECTING TO HOME STEREO SYSTEMS
The LINE OUT jack is made to accept a stereo mini plug (3.5mm). Simply connect the
cable’s mini plug to the LINE OUT jack on your player, and the other appropriate end
usually RCA JACKS to the CD/AUX INPUTS of your home stereo.
YOUR CD PLAYER
YOUR STEREO
SYSTEM
OPTIONAL CABLE (3.5mm)
TO RCA JACKS
TO AUX IN JACKS
TO LINE OUT JACK
4
IB-CD855(CDX82C-60C8)-WM-E-011604
WIRED REMOTE CONTROL
You can control the CD PLAYER with the provided remote control (including the functions
of PLAY/PAUSE AND POWER ON, STOP/OFF, SKIP/SEARCH and VOLUME CONTROL).
7
1. PLAY/PAUSE & POWER ON
2. STOP/OFF
6
5
1
3. SKIP/SEARCH BACKWARD
4. SKIP/SEARCH FORWARD
5. VOLUME CONTROL
6. BELT CLIP (at back)
7. HEADPHONES JACK
2
3
4
PLAYING CD’S WITH THE WIRED REMOTE CONTROL
The PHONES jack is made to play this player with the included WIRED REMOTE
CONTROL. Simply insert the WIRED REMOTE CONTROL’s plug to the PHONES jack
on right side of this player, and plug the STEREO HEADPHONES’ plug into the jack on the
top of the WIRED REMOTE CONTROL.
CD PLAYER
STEREO
HEADPHONES
REMOTE CONTROL
PLUG HEADPHONES INTO
PHONES JACK
TO PHONES JACK
(ONLY)
5
IB-CD855(CDX82C-60C8)-WM-E-011604
CD PLAYING
1 Load the Disc.
Push
here
Disc
Label side up
Push to open
2 Connect the Headphones.
Stereo Headphones
To PHONES jack
3 Press the PLAY/PAUSE button.
TOTAL PLAYING
TIME OF THE CD
TOTAL TRACKS
PLAY/PAUSE
button
TRACK NUMBER
CURRENTLY
PLAYING
ELAPSED PLAYING
TIME OF THE
CURRENT TRACK
VOLUME CONTROL
NOTE: The ESP PLUSTM function will turn on automatically when the PLAY/PAUSE
button is pressed.
4 Adjust the Volume.
6
IB-CD855(CDX82C-60C8)-WM-E-011604
OTHER OPERATIONS
Operation
Press
Display window shows
PLAY/PAUSE
button
To pause play
TRACK NUMBER
CURRENTLY PLAYING
PLAYING TIME
FLASHES
PLAY/PAUSE
button
To release pause and resume
play
TRACK NUMBER
CURRENTLY PLAYING
PLAYING TIME
ADVANCES
To stop
STOP button
TOTAL TRACKS TOTAL PLAYING TIME
STOP button once and wait 30 seconds, or press
STOP button twice.
To turn off the power
To skip to the next track(s)
SKIP + button once (or repeatedly).
SKIP - button once (or repeatedly).
To skip to the previous track(s)
To go ahead at high speed
(search)
Keep SKIP + button depressed and release when
the desired music section of the disc is found.
To go back at high speed
(search).
Keep SKIP - button depressed and release when the
desired music section of the disc is found.
BASS BOOST switch
This switch enhances the low frequency
(bass) sounds at low listening levels.
Switch the BASS BOOST switch ON or
OFF to suit your taste.
BASS BOOST switch
7
IB-CD855(CDX82C-60C8)-WM-E-011604
REPEAT AND INTRO PLAY
You may have repeat and intro play using the REPEAT button. Press the REPEAT button
several times, and the display will show the followings in turn:
REPEAT ONE --> REPEAT ALL --> INTRO --> NORMAL PLAY
Single Track Repeat
Plays one song over and over till you press STOP.
During play, select the song you want to repeat with
either of the SKIP + or SKIP - button, then press the
REPEAT button once, the symbol REPEAT ONE will appear
in the display.
The song currently playing will repeat over and over,
until you press STOP.
All Tracks Repeat
Repeats all songs in order, till you press STOP.
During play, press the REPEAT button twice, the symbol
REPEAT ALL will show in the display.
All songs will keep playing in sequence 1, 2, 3, etc., and
when finished, will start all over again until you press the
STOP.
Intro Play
This plays the first 10 seconds of songs in sequential
order.
1. During play, press the REPEAT button three times,
the word INTRO will flash in the display.
2. Press the PLAY button, the word INTRO will stop
flashing and the first 10 seconds of each song on the
CD will play in sequential order.
3. When you find a song you like, press the PLAY button
again, the symbol INTRO will disappear from the
display, normal play will be resumed, that song (and
the following songs) will play NORMALLY.
RANDOM PLAY
This plays the songs on the disc in a random order.
1. During play, press RANDOM button the word RND will
flash in the display.
2. Press the PLAY button, this will play all of the songs
in random order selected by the CD player. The word
RND will stop flashing.
3. Press the SKIP + button to skip to the next random
song.
8
IB-CD855(CDX82C-60C8)-WM-E-011604
PROGRAMMED PLAY
The tracks (songs) on the disc can be programmed (arranged in advance) to play in
any order you prefer (up to 20 tracks can be programmed).
Programming Example:
Program Number
1
3
etc.
etc.
2
5
3
8
4
1
5
2
6
4
7
1
8
1
Track Number (song number)
During programming, the word PROG flashes in the display. To program songs to play
in your preferred order, follow steps below:
1.Press the PROG. button.
3.Press the PROG. button to confirm.
Track 3 is now programmed.
Program number 2 will now show in the
display, ready for your next selection of
track.
The word PROG and “
” will flash in the
display.
4.Repeat steps 2 and 3 to program other
tracks till you finish (up to 20
selections).
5.After programming is finished, press the
PLAY button to begin programmed play.
The word PROG changes to be steadily
on in the display, and music begins to
play in the order you programmed.
Program number
2.Press the SKIP + or SKIP - button to
select track number 3 (example). PROG
and track number “03” will flash in the
display.
NOTE:
- The player will stop automatically after
all programmed tracks have been
played.
- To quit programmed play, press the
STOP button once. Then you may press
the PLAY button to re-start normal play.
Your programmed memory will be
lost:
When the alkaline batteries are
exhausted or removed, or the optional
AC ADAPTOR is disconnected.
•
Track number
When the power is shut off.
•
9
IB-CD855(CDX82C-60C8)-WM-E-011604
60 SECOND ESP PLUSTM ANTI-SKIP SYSTEM
This set is designed with the latest 60 second ESP PLUSTM (Electronic Shock Protection)
- which allows virtually unlimited gentle skip protection above the normal 60 second
shock protection.
The 60 second ESP PLUSTM function prevents the sound from skipping by using a
buffer memory that stores music data. The new 60 second ESP PLUSTM system can
store more music than normal 60 second anti-skip systems.
This new design allows gentle swaying of the set (as in walking) without music skipping.
This function (CD ESP PLUSTM) may not work during heavy jogging.
The 60 second ESP PLUSTM function will turn on automatically when the PLAY/PAUSE
button is pressed.
When the PLAY/PAUSE button is pressed, the “
” (memory
basket) indicator will appear in the display, the digital data (music)
is stored in the “read-ahead” memory buffer before it is decoded
and played.
EMPTY MEMORY
FULL MEMORY
The “
” mark changes to the “
” mark, indicating that the
memory buffer (basket) is full.
When the set is subject to a shock or a bump during play, the
data stored in memory continues to be decoded and played.
This gives the pickup time to stabilize and continue reading
new music. As the data is used from memory, the indicator
•
•
SOME MEMORY USED
changes from “
original position, new data is stored in memory and the display
changes back to the “ ” mark.
” to “
”. Once the pickup returns to its
If the set is subject to repeated shocks and all the data stored
in memory is used up, the “ ” mark is displayed and the
sound will skip or stop for a brief period until the memory basket
has time to fill up again.
ALL MEMORY USED UP
NOTE:
- The music may stop if the player receives continuous shocking.
- You may hear noise or skipping if the CD is dirty or scratched.
- If you press SKIP (+ or -) buttons, the memory basket will
empty itself temporarily.
10
IB-CD855(CDX82C-60C8)-WM-E-011604
MAINTENANCE
Handling Compact Discs
Cleaning the lens
Dirty, scratched or warped discs may
•
A dirty lens will cause sound skipping. If
the lens is very dirty, the player may not
work. We suggest using a special cleaning
disk (not included) available in most music
and Hi-Fi stores. However, if you do not
have one, you may use a cotton swab
very slightly dampened with alcohol to
clean the lens.
cause skipping or noise.
Handle the disc only by the edges. To
keep clean, do not touch its surface.
•
Discs should be stored in their cases
after use to avoid scratches.
•
Do not expose discs to direct sunlight,
•
high humidity, high temperatures, or
dust, etc. Prolonged exposure to
extreme temperatures can warp the disc
(such as leaving the discs in your car
during summertime).
Cleaning the cabinet
Wipe with a soft cloth. If the cabinet is
very dirty, dampen (not dripping wet) the
cloth with a weak solution of soapy water,
and then wipe clean.
Do not stick or write anything on either
•
side of disc. Sharp writing instruments, or
the inks used in some felt-tip pens, may
damage its surface.
Cleaning the Discs
To remove the Disc
Fingerprints should be carefully wiped
•
Open the CD DOOR by pressing the
DOOR OPEN button, hold the disc by the
edge while slightly pressing on the center
spindle as illustrated, then lift it from the
edge to release and remove.
from the surface of disc with a soft cloth.
Unlike conventional records, compact
discs have no grooves to collect dust
and microscopic dirt, so gently wiping
them with a soft cloth should remove
most particles. Wipe in a straight
motion from the center to the edge.
NOTE:
Never use thinner, benzine, record
Always press the STOP button and wait
for the disc to stop rotating before
pressing the DOOR OPEN button to
remove the disc.
•
cleaner or antistatic spray on a compact
disc. Such chemicals can damage its
plastic surface.
11
IB-CD855(CDX82C-60C8)-WM-E-011604
SAFETY PRECAUTIONS
Do not take the set apart. The laser beam used in the set may harm your eyes. Refer
servicing to qualified service personnel only.
Do not insert pins or coins, clips, or any objects inside the set.
This set is equipped with a safety device which automatically turns the laser beam off
when the CD DOOR is opened.
Do not drop the set or subject it to strong shocks. Doing so could result in damage.
Do not place the set in locations where the temperature is high, or in humid or dusty
locations, or locations with long heavy vibrations, or tilted surfaces.
The set’s cabinet may warp or the set may be damaged if it is placed in direct sunlight,
near heaters (where the temperature is 1400F/600C or higher) or in cars with the
windows closed. In the summer, the temperature may get as high as 2120F/1000C or
more.
Use the set within a temperature range of 410F/50C to 950F/350C.
Use ONLY the optional DC 4.5V AC ADAPTOR with polarity
, others may
damage your set. Disconnect the ADAPTOR from the wall outlet when the set is not to
be used for an extended period of time (3 days or more).
When cleaning your set, use a soft dry cloth. Do not use solvents or commercially
available cleaners, as they may damage or discolor the finish.
Do not wear headphones while operating a motor vehicle. This could create a traffic
hazard and is illegal in many areas. Do not use this set when bicycling or running.
The headphones supplied with your set provide superb stereo listening while allowing
you to hear some outside sounds when listening at normally low volume levels. Listening
at extremely high volume levels minimizes the intrusion of outside noise/sounds. In the
interest of safety, it is strongly advised against the use while engaging in activities
where the exclusion of external sounds (whistles, horns, sirens, traffic, etc.) could be
hazardous. Also loud volume can hurt your ears. If you notice that the sound has
become weak or distorted or if tracks do not change, this is an indication that your
batteries are weak. Replace both batteries at the same time (see Using with Batteries).
Your CD-855 is identified by a serial number stuck inside the battery compartment.
Record this number in the space provided below.
Model CD-855 Serial No.
Date Purchased:
This manual contains detailed information on its safety and use. Please read it carefully
so that you may take full advantage of its many features, and ensure a safe reliable
operation. Keep this manual for future reference.
CONDENSATION
If cold water is poured into a glass, water droplets form on the outside of the glass. This is
called condensation. Condensation may occur on internal operating parts of the lens.
Condensation occurs:
When the set is brought from the cold outdoors into a warm room, or if it is in a cold
room to a room which is heated, or in the summer, if the set is moved from an air-
conditioned room or car to a hot or humid location.
Should condensation occur, the set may not operate properly. Open the CD DOOR
and wait for about 20 minutes (to allow the internal parts to adjust to the surrounding
temperature) before using the set.
12
IB-CD855(CDX82C-60C8)-WM-E-011604
IMPORTANT REQUIREMENT BY THE FCC
Since the CD circuitry may cause interference to other radios nearby, switch this
set off when not in use or move it away from the affected radios.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
SAFETY CERTIFICATION
This Compact Disc Player is made and tested to meet safety standards of the FCC
requirements and comply with safety performance of the U.S. Department of Health
and Human Services, and also with FDA Radiation Performance Standards 21 CFR
Subchapter J.
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
•
LASER SAFETY
THIS SET EMPLOYS AN OPTICAL LASER BEAM SYSTEM IN THE CD MECHANISM,
DESIGNED WITH BUILT-IN SAFEGUARDS. DO NOT ATTEMPT TO DISASSEMBLE.
EXPOSURE TO THIS INVISIBLE LASER LIGHT BEAM MAY BE HARMFUL TO HUMAN
EYES. THIS IS A CLASS-1 LASER PRODUCT. USE OF ADJUSTMENTS OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS LASER LIGHT BEAM
EXPOSURE. THIS COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. THE LASER
MECHANISM IN THE SET CORRESPONDS TO THE STYLUS (NEEDLE) OF A RECORD
PLAYER. ALTHOUGH THIS PRODUCT USES A LASER PICK-UP LENS, IT IS
COMPLETELY SAFE WHEN OPERATED ACCORDING TO DIRECTIONS.
13
IB-CD855(CDX82C-60C8)-WM-E-011604
TROUBLE SHOOTING GUIDE
Causes
Solutions
Symptoms
Replace both batteries with fresh
alkaline batteries. Battery life with
fresh batteries is above 8 hours for
continuous CD play (rechargeable
batteries have 1/2 of that life).
Batteries are weak (they
may test OK on tester but
they are weak for CD
operation).
Tracks do not
change or set
does not play
normally.
Dead or weak batteries.
Replace both batteries with fresh ones.
CD Player will not
turn on.
Check AC ADAPTOR connection at
AC outlet and the rear side of the set.
The optional AC ADAPTOR
not connected properly.
Disc inserted incorrectly.
Defective compact disc.
CD DOOR not closed.
Re-insert disc with label side facing up.
Try another compact disc.
Close the door securely.
Disc will not play.
Take out the CD and leave the CD
Door open for about 20 minutes to
dry the moisture condensation.
Moisture has formed inside
the CD deck.
Re-insert headphone plug into
PHONES jack (not LINE OUT) on
the set or on the top of the REMOTE
CONTROL.
Headphone plug not
inserted properly.
No sound from
headphones.
VOLUME control set to Increase the volume of the set or
on the REMOTE CONTROL.
minimum.
Replace with fresh batteries or use
an optional AC ADAPTOR.
Weak batteries.
Defective compact disc.
Try another compact disc.
VOLUME control
has no function.
Headphones plugged into
LINE OUT jack.
Plug headphones into PHONES jack.
(NOT THE LINE OUT JACK)
The compact disc or lens is
dirty or CD is scratched.
Clean or replace the compact disc or
clean the lens.
Sound is skipping
or sound stops.
Strong vibrations.
Music is too loud.
BASS BOOST is ON.
Place the player on a stable level.
Lower the VOLUME control.
Sound is distorted.
Slide BASS BOOST switch to OFF.
Replace both batteries or use an
optional AC ADAPTOR.
Weak batteries.
Remove batteries and ADAPTOR.
Wait 15 seconds and re-insert. Make
sure batteries are fresh or the optional
ADAPTOR has power.
Electronic or static error
caused circuitry to lock.
Buttons do not
work.
14
IB-CD855(CDX82C-60C8)-WM-E-011604
TECHNICAL SPECIFICATIONS
CD Player Section
Frequency response ..............................
50Hz-15kHz +1/-2dB
Sampling frequency ................................
D/A converter .........................................
Error correction method ..........................
Pickup ...................................................
44.1kHz
1-bit
CIRC
Optical 3-beam semiconductor laser
(780 nm wavelength)
Laser diode material GaAIAs
Laser output less than 44.6µW
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CD-RW encoded discs.
General
Maximum output (stereo headphones) .....
Power Supply
20mW + 20mW
AC adaptor ...........................................
DC .......................................................
120V/60Hz DC 4.5V Output (not included)
3V: Using 2 size “AA” batteries (not included)
Set Dimensions (approximate)
1
Width ...............................................
Depth ..............................................
Height ..............................................
5
/
”
2
6 ”
1 ”
Weight (approximate) ........................... 9.5oz. (270g) (set only)
Because the products are subject to continuous improvement, LENOXX reserves the
right to modify product designs and specifications without notice and without incurring any
obligation.
15
IB-CD855(CDX82C-60C8)-WM-E-011604
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship under
normal use for a period of 90 days after purchase and we will repair it free of charge or
replace it at no charge, should it become defective under this warranty, providing you
submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or exchange, at no
charge, the set that is returned to LENOXX ELECTRONICS CORP. After the initial 90 day
period expires, and for a period of 12 months from original purchase, we will repair the unit
covering any part(s) that need to be replaced at no charge, but will charge for the cost of
labor, return postage paid by Lenoxx.
This warranty does not apply to any products which have been subject to misuse,
neglect or accident. This warranty does not cover broken headphones or cabinet.
UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. The following charges apply to repairs beyond the
warranty period: $10.00. Be sure to pack carefully and return postage paid insured
together with your money order (personal checks will not be accepted) and sales receipt to:
LENOXX ELECTRONICS CORP., 2 GERMAK DRIVE, CARTERET N.J. 07008
For customer service Dial:1-800-315-5885
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
© 2004 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
16
IB-CD855(CDX82C-60C8)-WM-E-011604
|