MODEL :
CK9902
AM/FM Clock Radio with 0.9” Display
NOTES:
LOCATION OF CONTROLS
1.) This radiouses apolarizedACplug which hasoneblade wider thanthe other.
This plug will only fit into a polarized AC outlet. This is a safety feature. If the
plug will not fit, you may have an older non-polarized AC outlet. Do not defeat
thesafetyfeaturebytryingtofilethewiderblade, or replacingtheplug. Contact
an electricianto replace your outdated outlet.
2
1
3
5
6
7
2.) Donotconnectthisunit toan ACoutletwhich iscontrolledby awall switch.The
ACoutlet shouldbe ‘ live’ at alltimes.
4
9
8
10
11
ANTENNAINFORMATION
FM - The FM antenna isbuilt into the AC power cord. Be sure the AC power cord
is fully unwound and extended to its full length for best FM reception.
AM - TheAM ferritebarantennaisinsidethe radiocabinet. IfAMreceptionisnoisy
or weak, tryturningtheradioslightlyuntilthe bar antennaispointingtowards
the transmitter. Experiment until you find the position which provides the
clearestreception.
12
13
14
15
OPERATING INSTRUCTIONS
SETTING THE TIME
•
Press and hold the CLOCK and HOUR buttons to advance the display to the
correcthour.
•
Press and hold the CLOCK and MINUTE buttons to advance the display to the
correctminute.
1. ALARM RESET Button.
2. SNOOZE/SLEEP OFF/RADIO OFF Button.
3. RADIO ON Button.
4. ALARM Button.
NOTE: If the AM Indicator in the upper left corner of the display is ‘ On’ , the time
displayed is “ AM” . If the AM Indicator does not appear in the display, the
time displayed is “PM”. Be sure to set the time correctly for AM or PM.
5. MINUTE Button.
6. CLOCK Button.
CLOCK DISPLAY
AM Indicator
7. HOUR Button.
ALARM Indicator
8. SLEEP Button.
9. DIMMER (Hi/Lo) Switch.
10. ALARM(OFF/RAD/BUZ) Switch.
11. VOLUME Control.
LISTENING TO THE RADIO
•
•
•
•
•
Press the RADIO ON button.
Slide the BAND selector to the desired position - AM or FM.
Select the desired station with the TUNING control.
Adjust the VOLUME control to the desired level.
12. Clock Display.
13. AM/FM Band Switch.
14. Dial Scale and Pointer.
15. TUNING Control.
Press the SNOOZE/SLEEP OFF/RADIO OFF button to shut the radio ‘ Off’ .
SETTING THE WAKE-UP TIME
•
•
PressandholdtheALARM andHOURbuttonstosetthedesired wake-uphour.
Press and hold the ALARM and MINUTE buttons to set the desired wake-up
minute.
PREPARATION FOR USE
SURE-ALARM BATTERY BACK UP SYSTEM
NOTE: If theAM Indicator inthe upper leftcorner of thedisplay is ‘ On’ , thewake-
uptimedisplayedis“ AM”.IftheAMIndicatordoesnotappearinthedisplay,
the wake-up time displayed is “PM” . Be sure to set the wake-up time
correctly for AM or PM.
Thisclockradioincludes abatterybackupsystem thatwill maintainthecorrecttime
andalarm settingsincase ofatemporary powerinterruption. Aslongasthebattery
has sufficient power, it will also operate the Radio or Buzzer alarm to wake you up
even ifthepoweris ‘ Off’ at your normal wake uptime. Thebatterybackup system
requires one 9 volt battery,(not included). We recommend you use an alkaline
battery for longest life.
WAKE TO RADIO
Setthewake-uptimeasindicatedabove.Alsotunetheradiotothebandandstation
that youwant tohear atthewakeup time, adjustthe volumeif necessary, and shut
theradio‘ Off’ .
•
•
•
Open the battery compartment door, located on the back of the radio cabinet.
Gentlypullthebatteryterminaloutsidethebatterycompartment.
Connect the 9 volt battery to the battery terminal. It can only be
connectedoneway.
•
•
Slide the ALARM selector to the RAD (Radio) position.
At the selected wake-up time the radio will begin to play. It will continue for
1 hour and 59 minutes and then shut off automatically and reset itself for the
followingday.
•
•
Push the battery and the terminal back into the battery
compartment.
Replacethebattery compartmentdoor.
•
•
To stop the radio sooner, press the ALARM RESET button. The radio stops
immediately and resets itself for the following day.
To cancel the wake to radio function slide the ALARM selector to the ‘ Off’
position.
If the power is interrupted the clock display goes ‘ Off ’ . However the clock will
continueto run, powered bythe9 voltbattery. Whenpowerisrestoredthe clockwill
come ‘ On ’ again to the correcttime. The alarm setting will also be maintained.
WAKE TO BUZZER ALARM
Set the wake up time as indicated above.
NOTE: If no battery is installed, or if the battery is exhausted and power is
interrupted,thetimeandalarmsettingswillbelost.Whenpowerisrestoredtheclock
display will begin flashing “ 12:00 AM” . This is your indication that the time is
incorrectand needstobereset. Don’ t forgettoreset boththetimeandthe wakeup
time.
•
•
Slide the ALARM selector to the BUZ (Buzzer) position.
At the selected wake up time the buzzer tone will come on. It will continue for 1
hour and 59 minutes and then shut off automatically and reset itself for the
followingday.
To stopthe buzzersooner, presstheALARM RESET button. Thebuzzer stops
immediately and resets itself for the following day.
To cancel the wake to buzzer function slide the ALARM selector to the ‘ Off’
position.
•
•
A fresh alkaline battery should beable to provide back up power for up to a year in
normal circumstances. However if you live in an area that has frequent power
interruptionsthebatterylifewillbereduced.Forbestresultsyoushouldinstallanew
batteryevery8 to12months.Ifyouinstalledabattery butyounoticethat thedisplay
is flashing, your battery is exhausted and should be replaced.
SNOOZE / REPEAT ALARM
Ifyouneedafewextraminutessleepafter thealarmcomeson,presstheSNOOZE
buttononce.Theradioor buzzer alarm stopsfor 9minutesandthenturnsonagain.
Thisprocedurecan berepeatedmanytimes ifnecessary. Eachtime theSNOOZE
button is pressed the alarm shuts off for 9 minutes and then comes on again.
NOTE: The Snooze / RepeatAlarm operationwill function for up to1 hour and 59
minutes after the alarm comes on. After 1 hour and 59 minutes the alarm
nolonger repeats.
POWER SOURCE
This radio operates on 120V, 60Hz AC house
current only. Unwind the AC power cord and
connect theplug toany convenientlylocated AC
outlet.
Visit our web site at “www.emersonradio.com”
|