AM/FM STEREO CLOCK RADIO
COMPACT DISC PLAYER
with DUAL ALARMS
and NAP TIMER
OWNER'S MANUAL
CKD3630
CKD3630_060404.p65
25
4/6/2004, 15:19
Thank you…………………
for purchasing this Emerson Dual Alarm Stereo Clock Radio with CD Player, and
Nap Timer. This compact sized unit has been designed to fit comfortably on any
desk or bedside table.
The CD Player has a 20-track programmable memory plus one-track/all tracks
automatic repeat playback. The clock radio features a large, easily readable, 0.9”
green LED display that is visible from anywhere in the room. The display brightness
can also be reduced if you feel it is too bright in a darkened room. The dual alarms
can be set and used independently. You can set either or both alarms to wake you
to an electronic buzzer tone, your favorite radio station, or your favorite CD. The
programmable 99-minute Nap Timer is like having a 3rd alarm. Use it to wake you
up after a short Nap without having to change your regular alarm settings.
And of course there’s a battery back up system that will maintain the time and
alarm settings in the event of a temporary power interruption
This system was designed to give you many years of enjoyment with an absolute
minimum of care and maintenance.
Please read this Owners Manual carefully and completely to ensure that you get
the maximum benefit from all the outstanding features we have included in this
product. If you encounter any problem with the set up or operation of this model
please do not return it to the retail store.
Please call the Emerson Customer Service Hotline toll free at 1-800-898-9020.
One of our service technicians will try to diagnose the problem for you.
Once again thanks for choosing this Emerson audio product.
For future reference, record the Serial Number in the space provided:
Model No: CKD3630
Serial No:
2
CKD3630_060404.p65
2
4/6/2004, 15:19
IMPORTANT NOTES
• Avoid installing this unit in places
• Operate controls and switches as
described in the manual.
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much heat,
places lacking ventilation or dusty areas,
places subject to constant vibration and/
or humid or moist areas.
• Before turning ‘On’ the power, make
certain that power cord is properly
installed.
• Store your CDs in a cool area to avoid
damage from heat.
• When moving the set, be sure to first
disconnect the power cord.
• Do not attempt to clean this unit with
chemical solvents as this might damage
the finish. Use a clean dry cloth.
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
INVISIBLE LASER RADIATION
WHEN OPENAND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
3
CKD3630_060404.p65
3
4/6/2004, 15:19
PREPARATION FOR USE
UNPACKING AND SET UP
• Carefully remove the unit from the display carton. Remove all the packing material
from the unit and remove any small strips of tape that may have been used to
prevent the CD door from opening in transit.
• Unwind and extend the FM lead wire antenna.
• This unit was shipped with a dummy CD transit card in the CD player. This
dummy CD prevents the laser pick up from moving during shipment. This card
must be removed before you can insert your own CDs. Raise the CD door,
remove the transit card and discard it.
• Place the unit on a flat, level surface such as a table, desk, counter, shelf, etc,
convenient to a 120V 60Hz AC outlet, out of direct sunlight, and away from
sources of excess heat, dust, moisture, or strong magnet fields.
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
4
CKD3630_060404.p65
4
4/6/2004, 15:19
BATTERY BACK UP SYSTEM
This model includes a battery back up circuit that will maintain the clock and alarm
settings in the event of a temporary power interruption. The battery back up system
requires one 9-Volt battery, not included. The battery compartment is located on
the back of the cabinet.
1.) Press the battery door-locking tab in the direction of the arrow and remove the
battery door.
2.) Connect a fresh 9-Volt alkaline battery to the battery terminal in the battery
compartment. It can only be connected one way.
3.) Replace the battery door.
If the power is interrupted the display will go off and the radio will not work. However
the battery will maintain the clock and alarm settings in memory. When the power
is restored the display will come on again and the clock and alarm settings will be
correct.
The life of the back up battery will depend on the frequency and length of the
power interruptions that you experience. For best results we suggest you install a
fresh battery every 9 to 12 months. Always use a well-known brand of alkaline
battery.
5
CKD3630_060404.p65
5
4/6/2004, 15:19
POWER SOURCE
This radio is designed to operate on 120V 60Hz AC only. Attempting to operate
this radio on any other power source could cause damage to the unit and such
damage is not covered by your warranty.
Make sure the radio is connected to an AC outlet that is always “live”. Do not
connect the radio to an outlet that is controlled by a wall switch.
NOTE:
This unit has a polarized AC plug with one wide blade and one narrow blade. This
plug will only fit into a matching polarized AC outlet. This is a safety feature to
reduce the possibility of electric shock.
If this plug will not fit in your AC outlet, you probably have an outdated non-polarized
outlet. You should have your outdated outlet changed by a qualified, licensed
electrician.
Do not file the wide blade on the plug, or use an adapter to make the plug fit into
your outlet. This defeats the safety feature and could expose you to electric shock.
AC Outlet
AC Plug
6
CKD3630_060404.p65
6
4/6/2004, 15:19
LOCATION OF CONTROLS AND INDICATORS
FRONT PANEL
11
12
13
9
10
8
14
15
16
7
6
17
18
5
4
3
19
20
2
1
25
24
23
22
21
14.) LED Display.
1.) PLAY/PAUSE
Button.
Button.
15.) NAP Indicator.
2.) SKIP REV.
16.) ALM (Alarm) 2 Indicator.
3.) REPEAT Indicator.
4.) POWER ‘On’ Indicator.
5.) SLEEP Indicator.
6.) Radio Dial Scale.
7.) ALM (Alarm) 1 Indicator.
8.) AM Indicator.
17.) PLAY/PAUSE / FM ST. Indicator.
18.) PROG. (Program) Indicator.
19.) SKIP FWD.
Button.
20.) STOP Button.
21.) ALARM 1 Button.
22.) ALARM 2 Button.
23.) REPEAT Button.
9.) SLEEP Button.
10.) NAP Button.
11.) CD Door.
24.) PROGRAM Button.
25.) TIME/DISPLAY Button.
12.) SNOOZE Button.
13.) POWER ON/OFF Button.
7
CKD3630_060404.p65
7
4/6/2004, 15:19
RIGHT SIDE PANEL
29
28
30
31
27
32
26
LEFT SIDE PANEL
35
34
36
33
37
26.) VOLUME Control.
27.) Function Selector Switch.
(CD/FM AUTO/AM)
33.) Back Up Battery Compartment.
34.) Left Speaker.
35.) ALARM 1 Selector Switch.
(MUSIC/BUZZER/OFF)
28.) TUNING Control.
29.) CD Door LIFT HERE tab.
30.) Right Speaker.
36.) ALARM 2 Selector Switch.
(MUSIC/BUZZER/OFF)
31.) FM Lead Wire Antenna.
32.) AC Power Cord.
37.) DIMMER (HI/LO) Selector Switch.
8
CKD3630_060404.p65
8
4/6/2004, 15:19
OPERATING INSTRUCTIONS
• Make sure you have installed the back-up battery in the battery
compartment.
• Make sure you have extended the FM Lead Wire Antenna to its full
length.
• Connect the AC power cord plug to a 120V 60Hz AC outlet.
SETTING THE CLOCK
When the radio is connected to the AC outlet for the first time the display will show
flashing “12:00”.
1.) First depress and hold the TIME/DISPLAY button and then press the SKIP
FWD.
button or the SKIP REV.
button to adjust the display forward or
back to the correct time. The display will move slowly at first, and then begin to
move rapidly.
2.) Be sure to set correctly for AM or PM. If the AM indicator is ‘On’, the time
displayed is AM. When the display shows the correct time, release all the
buttons.
9
CKD3630_060404.p65
9
4/6/2004, 15:19
SETTING THE WAKE-UP TIMES
The procedure for setting the Alarm 1 and Alarm 2 wake up times is the same.
1.) First depress and hold the ALARM 1 button, then press the SKIP FWD.
button or the SKIP REV.
to adjust the display forward or back to the correct
Alarm 1 wake-up time. The display will move slowly at first, and then begin to
move rapidly.
2.) Be sure to set correctly for AM or PM. If the AM indicator is ‘On’, the wake-up
time displayed isAM. When the display shows the correct wake-up time, release
all the buttons.
3.) Depress and hold the ALARM 2 button, then press the SKIP FWD.
button
or the SKIP REV.
to adjust the display forward or back to the correct Alarm
2 wake-up time.
To check the wake-up times just press the ALARM 1 or ALARM 2 button at any
time. The display will show the wake-up time as long as the ALARM 1 or ALARM 2
buttons are depressed.
10
CKD3630_060404.p65
10
4/6/2004, 15:19
LISTENING TO THE RADIO
1.) Slide the function CD/FM AUTO/AM selector switch, located on the right side
cabinet, to the FM AUTO or AM position.
2.) Press the POWER ON/OFF button on the top panel to turn the system ‘On’.
The POWER indicator comes ‘On’.
3.) Tune to the desired station by slowly rotating the TUNING control on the right
side. If you tune to an FM Stereo station the FM ST. indicator will come ‘On’.
Note: If you tune to a weak or distant FM stereo station the tuner may
automatically switch to the FM Mono mode to provide better reception, but
the sound will no longer be in stereo.
4.) Adjust the VOLUME control to the desired level.
5.) When you are finished listening press the POWER ON/OFF button on the top
panel to shut the radio ‘Off’. The POWER indicator goes ‘Off’.
Hints For Better Reception
FM – Adjust the position and
direction of the FM lead wire antenna
until you find the position and
direction that provides the best
reception.
AM – The AM ferrite bar antenna
is inside the cabinet. If the AM
reception is unsatisfactory try
rotating the entire cabinet slightly
until the internal antenna picks up
the strongest signal.
11
CKD3630_060404.p65
11
4/6/2004, 15:19
PLAYING COMPACT DISCS
IMPORTANT:
This CD player can play normal CDs plus CD Recordable (CD-R) and CD
Rewriteable (CD-RW) discs. However the playability of CD-R/RW discs may be
affected by the type of software that was used in ‘ripping’ the tracks from the
original discs and ‘burning’ the tracks onto the blank media. Playability may also
be affected by the quality and condition of the blank media you use for recording.
100% compatibility cannot be guaranteed. This is not an indication of any problems
with your player.
1.) Slide the function CD/FM AUTO/AM selector switch on the right side cabinet
to the CD position.
2.) Press the POWER ON/OFF button on the top panel. The display will briefly
show “Cd” and then two dashes “ – – ” in the track number display.
After a few seconds the display will return to the correct time.
3.) Lift the CD door and place a CD on the
center spindle with the printed label side
facing up. Gently press downward on the
disc near the center hole until it is properly
‘seated’ on the spindle. Close the CD
door.
4.) The disc will spin for a few seconds as the player
reads the disc. Then the disc will stop and the
display will show the total number of tracks on
the disc.
After 5 seconds the display returns to the correct time.
12
CKD3630_060404.p65
12
4/6/2004, 15:19
5.) Press the PLAY/PAUSE
button on the front
panel to begin playback on track 1.
FM ST.
Track number “1” appears in the display and the PLAY/
PAUSE indicator comes ‘On’. After 5 seconds the display
returns to the correct time.
PLAY/PAUSE
6.) Adjust the VOLUME control to the desired level.
7.) Playback will continue until the last track has played then the disc stops and
the PLAY/PAUSE indicator goes ‘Off’.
The display briefly shows the total number of tracks on the disc and then returns
to the correct time. To stop playback before the disc ends press the STOP
button on the front panel. The disc stops and the display briefly shows the total
tracks on the disc and then returns to the correct time.
8.) If you are finished listening open the CD door and remove your disc.
9.) To listen to the radio slide the function selector switch (CD/FM AUTO/AM) to
the FM AUTO or AM position, or press the POWER ON/OFF button to turn the
power ‘Off’.
Note: To see the CD track number during playback, press the TIME/DISPLAY
button on the front panel. The display will change from correct time to CD
track number for 5 seconds, and then return to the correct time display.
PAUSE Control
To pause momentarily during CD playback press the PLAY/PAUSE
button on
the front panel again.
FM ST.
The sound stops and the PLAY/PAUSE indicator flashes but the
disc continues to spin. Press the PLAY/PAUSE
button again
PLAY/PAUSE
to cancel the Pause mode and resume normal playback.
The sound resumes at the same point on the disc and the PLAY/PAUSE indicator
stops flashing.
13
CKD3630_060404.p65
13
4/6/2004, 15:19
SKIP/Search (
/
) Controls
During playback press the SKIP FWD.
or SKIP REV.
buttons on the front
panel repeatedly to skip forward or back to higher or lower numbered tracks.
Playback will start at the beginning of the selected track.
To search within a track for a specific musical passage depress and hold the SKIP
FWD.
or SKIP REV.
buttons on the front panel.
The player will search rapidly forward or backward as long as the buttons are
depressed. When you hear the desired passage release the buttons and normal
playback will resume at that point.
Note: The volume is automatically reduced during high speed music search.
To start playback from a specific track load your disc as usual and wait until the
display shows the total number of tracks.
Press the SKIP FWD.
or SKIP REV.
buttons repeatedly until the desired
track number appears in the display then press the PLAY/PAUSE
button to
begin playback on the desired track.
14
CKD3630_060404.p65
14
4/6/2004, 15:19
SPECIAL PLAYBACK MODES
REPEAT PLAYBACK
You can program the player to continuously repeat a single track or the entire disc.
The Repeat mode can be selected while the disc is playing or while the disc is
stopped.
Single Track Repeat
Select the track to be repeated and then press the REPEAT button on the front
panel once.
The REPEAT indicator begins flashing.
If necessary, press the PLAY/PAUSE
button to begin playback.
REPEAT
The selected track will be repeated continuously.
All Tracks Repeat
Press the REPEAT button on the front panel twice.
The REPEAT indicator remains ‘On’.
If necessary, press the PLAY/PAUSE
button to begin playback.
REPEAT
The entire disc will be repeated continuously.
To cancel Repeat playback press the REPEAT button on the front panel until the
Repeat indicator goes ‘Off’.
Repeat Playback mode may also be cancelled by pressing the STOP button,
switching to Radio function, or pressing the POWER ON/OFF button to shut the
power ‘Off’.
15
CKD3630_060404.p65
15
4/6/2004, 15:19
PROGRAMMED PLAYBACK
Use the Programmed Playback feature to play up to 20 tracks on a disc in any
desired order. You may also program a particular track to play several times within
a programmed sequence if desired.
Note: You cannot program a disc while it is playing. Press the STOP button
to stop playback and then follow the programming steps below.
1.) Load your disc as usual and wait until the display
shows the total number of tracks on the disc.
2.) Press the PROGRAM button on the front panel.
The PROG. indicator flashes and Track number
“0” begins flashing in the display.
PROG.
3.) Press the SKIP FWD.
or SKIP REV.
buttons to select the first track
number to be programmed.
Example: Track number 7.
When the desired track number appears in the display press the PROGRAM
button again.
Track 7 is now entered in Program Memory
number “01”. The Track number display returns
to the flashing “0”.
4.) Repeat step 3, selecting a different track number
each time until you have entered up to 20 tracks
in the program memory.
To confirm the program after you have entered the last track press the
PROGRAM button repeatedly. The display will scroll through all the tracks you
programmed in sequence.
16
CKD3630_060404.p65
16
4/6/2004, 15:19
5.) When you have completed programming the desired tracks press the PLAY/
PAUSE button to begin programmed playback.
FM ST.
The PLAY/PAUSE indicator comes ‘On’ and the
PROG. indicator continues flashing.
PROG.
PLAY/PAUSE
Playback will begin on the first track you programmed and will continue until
the last programmed track has played.
6.) When the program is completed the player stops and the display again briefly
shows the total tracks on the disc and then returns to the correct time. However
the program sequence remains in the memory.
To repeat the program sequence press the PROGRAM button and then press
the PLAY/PAUSE
button again.
To cancel the Programmed sequence from memory, press the PROGRAM
button and then press the STOP button while the player is stopped. The
Program indicator goes ‘Off’.
Programmed Playback may also be canceled by switching to Radio function,
opening the CD door, or pressing the POWER ON/OFF button to shut the
power ‘Off’.
PROGRAMMED REPEAT PLAYBACK
You may use the Programmed Playback and Repeat features together to
continuously repeat a programmed sequence.
First program the desired sequence according to steps 1 through 4 above.
When Programmed Playback begins press the REPEAT button twice to select the
Repeat All Tracks mode.
FM ST.
The REPEAT and PLAY/PAUSE indicators
REPEAT
PROG. PLAY/PAUSE
remain ‘On’. The PROG. indicator flashes.
The programmed sequence will be repeated continuously.
17
CKD3630_060404.p65
17
4/6/2004, 15:19
ALARM FUNCTION
You can use the alarm function to wake you to an electronic buzzer tone, the radio,
or your favorite CD.
First press the ALARM 1 or ALARM 2 buttons on the front panel to check the
Wake Up time settings. Adjust the Wake Up times if necessary.
Wake To Buzzer (Crescendo Alarm)
Slide the ALARM 1 and/or ALARM 2 selector switches on the left side panel to the
BUZZER position.
The ALM 1 and or ALM 2 indicators appear in the display. At the selected wake up
time the buzzer will sound.
It will start softly and gradually increase in volume to wake you up. The buzzer
alarm will continue for one hour and then shut off automatically.
To stop the buzzer alarm sooner press the ALARM 1 and/or ALARM 2 buttons on
the front panel.
Note: Alarm 1 and Alarm 2 have different buzzer sounds so you can easily tell
which alarm is going off.
Wake To Radio
Tune to the desired radio station and adjust the volume to the level you want to
hear in the morning when the alarm comes on.
Press the POWER ON/OFF button to shut the system ‘Off’.
Slide the ALARM 1 and/or ALARM 2 selector switches on the left side panel to the
MUSIC position.
The ALM 1 and or ALM 2 indicators appear in the display. At the selected wake up
time the radio will turn on. It will continue for one hour and then shut off automatically.
To stop the radio alarm sooner press the ALARM 1 and/or ALARM 2 buttons on
the front panel.
18
CKD3630_060404.p65
18
4/6/2004, 15:19
Wake To CD
IMPORTANT: This model includes an automatic default to the Buzzer alarm if
the player cannot read the disc that you selected for wake-up. If the player
cannot read the disc's Table of Contents (TOC) within 8 seconds, it assumes
that the disc is either defective or inserted incorrectly, and the system
automatically defaults to the Buzzer alarm to make sure that you wake up on
time. The TOC of CD-RW discs may take longer to read than normal CD's.
Therefore if you are trying to wake to a CD-RW disc and you are awakened by
the Buzzer alarm instead, this is because the TOC on your CD-RW disc took
too long to read.
This is normal and not an indication of any problem with your unit.
Load the desired CD, begin playback and adjust the volume to the desired level.
Press the POWER ON/OFF button to shut the system ‘Off’.
Slide the ALARM 1 and/or ALARM 2 selector switches on the left side panel to the
MUSIC position. The ALM 1 and or ALM 2 indicators will appear in the display.
At the selected wake up time the CD will begin to play. It will continue for one hour,
or until the end of the disc, and then shut off automatically.
To stop the CD alarm sooner, press the STOP button or press the ALARM 1
and/or ALARM 2 buttons on the front panel.
The Alarm will automatically repeat each day at the selected Wake Up time as
long as the ALARM 1 and/or ALARM 2 selector switches are set to the BUZZER
or MUSIC positions.
To cancel the alarms, slide the ALARM 1 and/or ALARM 2 selector switches to
the OFF position. The ALM 1 and or ALM 2 indicators go ‘Off’.
SNOOZE FUNCTION
After the alarm turns on in the morning you can use the Snooze function to grab a
few more minutes sleep before the alarm sounds again.
To activate the Snooze function press the SNOOZE button on the top cabinet, the
Snooze function will stop the alarm for 9 minutes and then turn the alarm on again.
The selected ALM 1 and or ALM 2 indicator flashes during Snooze operation.
The Snooze operation can be repeated several times within one hour. But after
one hour the alarm will not turn on again.
19
CKD3630_060404.p65
19
4/6/2004, 15:19
SLEEP Timer
You can fall asleep to the radio or CD player and the sleep timer will shut the
system off automatically after up to 99 minutes of music.
Sleep To Radio
Set the function selector switch (CD/FM AUTO/AM) to the FM AUTO or AM position.
Press the SLEEP button on the top panel. The SLEEP
indicator comes ‘On’ and the radio turns ‘On’.
SLEEP
POWER
Select the desired station and volume level. The radio will shut off automatically
after 30 minutes. To shut off the radio sooner press the SNOOZE button or the
POWER ON/OFF button.
Sleep To CD
Set the function selector switch (CD/FM AUTO/AM) to the CD position.
Insert a CD in the player. Press the SLEEP
FM ST.
button on the top panel and then press the
PLAY/PAUSE
button. The SLEEP and
SLEEP PLAY/PAUSE
POWER
PLAY/PAUSE indicators come ‘On’. The CD
begins to play.
The CD player will shut off automatically after 30 minutes, or after the last track
has played, whichever comes first.
To shut off the CD player sooner press the STOP button, the SNOOZE button or
the POWER ON/OFF button.
20
CKD3630_060404.p65
20
4/6/2004, 15:19
Adjusting The Length of The Sleep Timer
The sleep timer default setting is 30 minutes but it can be adjusted downward or
upward to a maximum of 99 minutes.
Depress and hold the SLEEP button. The display will
show “L:30” indicating that the power will shut off
after 30 minutes.
To adjust the sleep time continue holding the SLEEP button and depress the SKIP
FWD.
or SKIP REV.
buttons on the front panel until the display shows the
desired sleep timer length.
Notes:
1.) When you change the sleep timer setting, your new setting becomes the default
setting.
For example if you change the sleep timer setting from 30 minutes to 45 minutes,
each time you press the SLEEP button the system will operate for 45 minutes.
(Exception: If you have a power failure and there is no back up battery
installed, or the back up battery is dead, the sleep timer will return to the
original 30 minute default setting when the power is restored.)
2.) If the sleep timer is set for 60 minutes but your CD is only 45 minutes long the
player will shut off at the end of the disc.
21
CKD3630_060404.p65
21
4/6/2004, 15:19
NAP Timer (Buzzer Alarm Only)
This model features a programmable 99-minute Nap Timer that can be used to
wake you after naps of up to 99 minutes without disturbing your regular alarm
settings.
Depress and hold the NAP button on the top panel.
NAP
The display shows “n:30”, indicating that the buzzer
alarm will sound in 30 minutes, and the NAP indicator
appears in the display.
To adjust the length of the Nap Timer continue holding the NAP button and depress
the SKIP FWD.
or SKIP REV.
buttons on the front panel until the display
shows the desired Nap Timer length.
At the selected Nap time the buzzer will sound. It will start softly and gradually
increase in volume to wake you up. The buzzer alarm will continue for one hour
and then shut off automatically.
To stop the buzzer sound sooner press the SNOOZE or POWER ON/OFF button
on the top panel.
Note:
When you change the Nap Timer setting, your new setting becomes the default
setting.
For example if you change the Nap Timer setting from 30 minutes to 45 minutes,
each time you press the NAP button the buzzer will sound after 45 minutes.
(Exception: If you have a power failure and there is no back up battery installed,
or the back up battery is dead, the Nap Timer will return to the original 30
minute default setting when the power is restored.)
Display DIMMER
This model was shipped with the DIMMER switch set to the HI (High) position for
maximum display brightness. If you feel that the display is too bright for sleeping,
set the DIMMER switch to the LO (Low) position.
22
CKD3630_060404.p65
22
4/6/2004, 15:19
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.
1901 Diplomat Drive.
Farmers Branch, TX 75234.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
TO FIND THE LOCATIONAND PHONE NUMBER
OF YOUR NEAREST SERVICE CENTER
PERMITTED TO PERFORM WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.
Consumer Affairs Dept.
1901 Diplomat Drive,
Farmers Branch, TX 75234.
23
CKD3630_060404.p65
23
4/6/2004, 15:19
EMERSON
Part No. 16-2958
406-01
Printed in China
CKD3630_060404.p65
24
4/6/2004, 15:19
|