CD-RECEIVER
KDC-XBT8013U
KDC-XBT8013UL
KDC-X7013U
KDC-X7013UL
INSTRUCTION MANUAL
© B64-4418-00/00 (MW/M3W)
Before use
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to GB2312 or ISO 8859-1
can be displayed. Refer to “MENU” > “Chinese” of
<Function Control> (page 6).
• Characters that conform to ISO 8859-1 (“English”),
Windows CP 1256 (“Arabic”/ “Persian”) and Windows
CP 874 (“Thai”) can be displayed. Refer to “MENU” >
“Language” of <Function Control> (page 6).
• In this document, the description indicator will light
means a status is displayed. Refer to <Display Type
Selection> (page 10) for the details of the status
display.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
2WARNING
To prevent injury or fire, take the following
precautions:
• To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Do not use this unit before canceling
Demonstration mode!
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode setting> (page 23).
How to reset your unit
• If this unit or the connected unit (disc auto changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
Reset button
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
CDs that cannot be used
• CDs that are not round cannot be used.
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
English
|
3
Basic Operation
[
]
Release
[SRC]
Microphone
AUX
Auxiliary
input
[FNC]
USB Terminal
[
]
[AUD]
Control
knob
[AUTO]
Auxiliary input
Connect a portable audio device with mini-plug
cable (3.5 ø).
General functions
Power/Source Select button: [SRC]
Turns on the power.
⁄
When the power is ON, select a source.
SRC Select mode 1: Press the [SRC] button and then
turn the Control knob or push it toward up or down.
To determine the selected source, press the Control
knob.
SRC Select mode 2: Pressing this button each time
switches between sources.
Tuner (“TUNER”) , USB or iPod (“USB” or “iPod”),
CD (“CD”) , Auxiliary input (“AUX”), and Standby
(“STANDBY”)
•
Use the mini-plug cable which is stereo type and does not
have any resistance.
•
The auxiliary input requires the setting made in “MENU” >
“AUX” of <Function Control> (page 6).
Text/Title scroll: Control knob
Scrolls the CD and audio file text display when
pushing toward up for at least 2 seconds.
Muting volume upon reception of phone call
When there is a call, “CALL” is displayed and the audio
system is paused.
Press at least 1 second to turn off the power.
When the call ends, “CALL” disappears and the audio
system comes back on.
The audio system comes back on when [SRC] is
pressed during a call.
⁄
•
The SRC Select mode can be set in “MENU” > “SRC Select” of
<Function Control> (page 6).
•
Auxiliary input source is initially set to “OFF”. Set “Built in
AUX” described in <Function Control> (page 6) to “ON”.
: Select “MENU” > “Built in AUX”
⁄
•
To use the TEL Mute feature, you need to hook up the MUTE
wire to your telephone using a commercial telephone
accessory. Refer to <Connecting Wires to Terminals> (page
45).
•
•
•
When an optional accessory is connected, the source name
for each device appears.
When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
USB (iPod) source is recognized as CD source on the
connected unit.
Function Control: [FNC]
Pressing this button allows you to set various
functions using the Control knob. Refer to <Function
Control> (page 6).
Volume control: [AUD] knob
Turn the knob to adjust the volume.
Category Function of setup item
Subwoofer output: Control knob
MENU
SETUP
SOUND
BT
Allows you to set up the environment.
Switches between ON (“SUBWOOFER ON”) and OFF
(“SUBWOOFER OFF”) each time pushing toward down
for at least 2 seconds.
Allows you to set up the display and color.
Allows you to set up the sound environment.
Allows you to set up the Bluetooth function.
Allows you to set up the each source function.
—
|
4
KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Favorite Control: Control knob
You can recall the various registered functions by
⁄
•
3 inch (8 cm) CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
turning the Control knob.
For example, you can recall and playback the playlist
in iPod while listening to Tuner.
Refer to <Favorite Control> (page 30).
Disc ejection: [0]
⁄
•
You can eject the disc for 10 minutes after switching off the
engine.
Tuner functions
USB device/iPod play: USB Terminal
Connecting a USB device starts playback.
FM band: Control knob
Switches between FM1, FM2, and FM3 each time
pushing toward up.
⁄
•
For the playable audio file, media, and devices, refer to
<About Audio file> (page 40).
AM band: Control knob
Switches to AM when pushing toward down.
Pause and play: Control knob
Switches between pause and play each time this
button is pressed.
Tuning: Control knob
Changes the frequency when pushing toward left or
right.
USB device removing: [0]
Press this button for 2 seconds or longer to select the
remove mode, and the remove the USB device.
During the remove mode, “USB REMOVE” is displayed.
⁄
•
During reception of stereo stations the “ST” indicator is ON.
Tuning mode select: [AUTO]
• For KDC-X7013U/ KDC-X7013UL:
Switches as follows each time this button is pressed.
• For KDC-XBT8013U/ KDC-XBT8013UL: Switches as
follows each time this button is pressed for at least
1 second.
Music search: Control knob
Changes the music when pushing toward left or right.
Fast reverses or forwards the music while keeping
pushing toward left or right. (No sound is output
while playing audio file.)
Folder search: Control knob
Tuning mode
Display
Operation
Changes the folder containing the audio file when
pushing toward up or down.
Auto seek
“Seek Mode :
Auto1”
Automatic search for a station.
Preset station seek “Seek Mode :
Auto2”
Search in order of the stations in
the Preset memory.
•
For the operation on iPod, enter <Music Search for iPod>
(page 12) is first to enter the search mode.
Manual
“Seek Mode :
Manual”
Normal manual tuning control.
Search mode: [
]
After pressing [SEARCH] button, you can quickly
search songs with the Control knob. See <Music
Search> (page 12) for details.
Disc & Audio file play functions
Drop open the faceplate: Release
⁄
Hands-free phoning
•
Push the faceplate on the left side, and return it to its
former position.
Microphone:
(Accessory of KDC-XBT8013U/ KDC-XBT8013UL)
The microphone for the hands free phone is supplied.
When your voice cannot be recognized due to the
low microphone volume or noises in the vehicle,
adjust the microphone settings by selecting “MENU”
>“Mic Gain” of <Function Control> and “MENU” >“NR
Level” of <Function Control> (page 6).
Disc play: Disc slot
Starts playing when a disc is inserted.
When a CD is inserted, the “CD-IN” indicator is ON.
English
|
5
Function Control
Functions in the table below can be set up by using Function Control.
Displayed item is depending on currently selected
1 Enter Function Control mode
source or mode. The mark in Condition column
shows the condition to which the item is displayed.
: Can be set in other than standby state.
: Can be set in standby state.
Press the [FNC] button.
2 Select a Function group.
Push the Control knob towards right or left.
Pushing the Control knob towards left allows you
to set the preference items (“MENU”, “SETUP”, or
“SOUND”).
: Can be set while Audio file source of CD/USB/iPod.
: Can be set while Audio file source of CD/USB
(excluding iPod).
: Can be set while CD/ Disc changer source.
: Can be set while CD source.
Pushing the Control knob towards right allows you
to set the currently selected source function item
ON/OFF.
: Can be set while Disc changer source.
: Can be set during Tuner source.
: Can be set during FM reception.
3 Select your desired setup item
: Can be set while accessing AUX source.
: Can be set only during playback of the iPod source.
: Can be set for sources other than the standby
source by setting “2 ZONE” of <Audio Setup> (page
24) to “ON”.
: Can be set while a cell-phone is connected.
: Sets “ILM MSC SYNC” in the menu to “OFF”.
: Refer to the reference page.
Operation type
Movement between items Turn the Control knob.
Selection of item Press the Control knob.
Return to previous item Press the [FNC] button.
Select“Return”at the bottom of the item list.
Operation
Repeat selection and determination until your
desired setup item is selected.
Example:
—
: Can be set during all sources.
The Control knob is used for entry, but how to use
the knob varies depending on the setting items.
: Press the Control knob to switch the settings.
MENU
SETUP
SOUND
□ TRACK SCAN
□ DISC RANDOM
□ TRACK REPEAT
: Push the Control knob towards left or right to
switch the settings.
MENU
SETUP
SOUND
□ TRACK SCAN
□ DISC RANDOM
□ TRACK REPEAT
: Turn the Control knob to switch the settings.
Scr o ll： Au t o
1 sec. : Press the Control knob for 1 second to enter into
MENU
C D R ead： 1
the setting mode.
DEM O M o d e： OFF
Disp lay： OFF
ILM M SC SY NC： OFF
2 sec. : Press the Control knob for 2 seconds to enter into
In this manual, the above selection is
indicated as
Select “MENU” > “DEMO Mode”.
Each item’s ”&” will be ”✓” when the source function
is set to ON.
the setting mode.
⁄
•
•
•
Refer to the respective page for information on how to
set the items with reference page number.
Only the items available to the current source are
displayed.
The “SOUND” setting cannot be performed while the
Dual Zone function is used.
4 Make a setting
Push the Control knob towards up or down.
Press the Control knob to set the source function
item ON/OFF.
• Some items require you to keep pressing the
Control knob for 1 or 2 seconds so that you can
make a setting. For these items, the time during
which you need to keep pressing the Control
knob is displayed in the Entry column in seconds.
• For the functions accompanied by the
description of the setting procedure and so forth,
the reference page numbers are displayed.
*Factory setting
* Function of KDC-XBT8013U.
* Function of KDC-XBT8013UL.
* Function of KDC-X7013U.
* Function of KDC-X7013UL.
* Refer to <Menu Glossary> (page 42).
5 Exit Function Control mode
Press the [FNC] button for at least 1 second.
|
6
KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Source function item
Function
Setting
Entry
Setting overview
Condition Page
“iPod BY HAND”
“ON”/“OFF”*
When set to “ON”, allows you to operate iPod with the
control on the iPod.
13
“FILE SCAN”
“ON”/“OFF”*
“ON”/“OFF”*
“ON”/“OFF”*
When set to “ON”, plays the intro of the music in the
folder successively.
—
—
13
“FOLDER RDM”
“ALL RANDOM”
When set to “ON”, plays the music in the folder
randomly.
When set to “ON”, all songs in iPod are played at
random.
“FILE REPEAT”
“FOLDER REP”
“ON”/“OFF”*
When set to “ON”, plays the music repeatedly.
—
—
“ON”/“OFF”*
When set to “ON”, plays the music in the folder
repeatedly.
“TRACK SCAN”
“ON”/“OFF”*
When set to “ON”, plays the intro of the music on the
disc successively.
—
“DISC RANDOM”
“ON”/“OFF”*
When set to “ON”, plays the music on the disc randomly.
—
—
“MAGAZINE RDM”
“ON”/“OFF”*
When set to “ON”, plays the music in the disc changer
randomly.
“TRACK REPEAT”
“DISC REPEAT”
“ON”/“OFF”*
When set to “ON”, plays the music repeatedly.
—
—
“ON”/“OFF”*
When set to “ON”, plays the music on the disc
repeatedly.
“AUTO MEMORY”
Memorizes 6 stations with good reception
automatically.
15
Preference item
Category Item
Setting
Entry
1 sec.
Setting overview
Condition Page
“MENU”
“Security Set”/
“Security Clear”
—
Sets/Resets security code.
21
“SRC Select”
“1”*/“2”
Sets the source selection method.
*
“Skip Search”
“0.5%”*/
“1%”/“5%”/
“10%”
Sets the ratio of skip performed with <Music Search
for iPod>.
12
“Device Regist”**
—
Register a Bluetooth device (pairing).
32
32
1 sec.
1 sec.
1 sec.
“SPCL DVC Select”**
—
Allow registration of a special device that cannot be
registered normally.
“Phone Selection”**
—
Select a cell-phone subject to hands-free connection.
33
“Audio Selection”**
—
—
1 sec. Select the Bluetooth audio player to be connected.
Cancel registration of the Bluetooth device.
—
—
33
34
“Device Delete”**
1 sec.
“BT DVC Status”**
—
—
1 sec. Display the status of the Bluetooth device.
*
“PIN Code Edit”**
Specify the PIN code required when registering this unit
using the Bluetooth device.
32
1 sec.
“Auto Answer”**
“Mic Gain”**
“NR Level”**
“OFF”/“0S”–
“8S”* –“99S”
Answer a call automatically after lapse of the preset
time interval for automatic answer.
*
*
*
“–2”–“0”* –
“+2”
Adjusts the sensitivity of the built-in microphone for a
telephone call.
—
—
“–2”–“0”* –
“+2”
Reduces the noises generated by the surrounding
environment without changing the microphone
volume.
Next page 3
English
|
7
Function Control
Category Item
“SP Select”**
Setting
Entry
Setting overview
Condition Page
“Front”*/
Specify the voice output speaker.
*
“F-R”/“F-L”
“Call Beep”**
“ON”*/“OFF”
Output a beep from the speaker when a call comes in.
Display the firmware version and update the firmware.
*
“BT F/W Update”**
—
34
1 sec.
“Beep”
“OFF”/“ON”*
Setting the operation check sound (beep sound) ON/
OFF.
—
“Clock Adjust”
“Date Adjust”
—
—
1 sec. Sets the clock.
—
22
22
Sets the date.
1 sec.
1 sec.
“Date Mode”
“DSI”
7 types
Sets the date display mode.
22
“OFF”/“ON”*
DSI (Disabled System Indicator) of the unit blinks when
the faceplate is removed.
—
“Illumi DIM”
“OFF”/“Auto”*
/“MNAL1”/
“MNAL2”
Sets whether the illumination is dimmed in conjunction
with the light switch of the vehicle or it is dimmed
constantly.
*
“ILM Effect”
“OFF”/“ON”*
“OFF”*/“ON”
“OFF”/“ON”*
Sets whether the key illumination brightness is
changed in conjunction with the key operation.
—
—
“ILM MSC SYNC”
Sets whether the key illumination color is changed in
conjunction with the sound volume.
—
—
“Display”
Turns off the display when no operation is performed.
*
*
“DISP DIM“
“OFF”/“Auto”*
/“MNAL1”/
“MNAL2”
Dims the display part in conjunction with the light
switch of the vehicle.
Contrast
“1”-“10”
Adjusting the display contrast.
—
DISP N/P
“POSI 1”/“2”
/“NEGA 1”/“2”
Switches the panel display between positive or
negative.
*
“AMP”
“OFF”/“ON”*
Turns on/off the built-in amplifier.
*
*
“Zone2”
“Rear”*/“Front”
Specifies the destination of AUX input sound when the
Dual Zone function is turned on.
“AMP Control”
“CRSC”
—
Controls the connected LX amplifier.
—
22
“OFF”/“ON”*
Switches to Monaural to decrease noise when
reception is poor.
—
“Name Set”
Sets the display when switched to AUX source.
11
1 sec.
“Language”**
“English”*/
“Arabic”/
“Persian”/
“Thai”
Selects the language for using on the display.
*
“Chinese”**
“OFF”*/“ON”
Selects Chinese as the display language.
*
“Scroll”
“Auto”*/
Specifies whether the text is scrolled automatically.
—
—
“Manual”
“Favorite Delete”
“Built in AUX”
—
Deletes Favorite Preset Memory.
30
1 sec.
“OFF”*/“ON”
Sets whether to display AUX during source selection.
—
“CD Read”
“1”*/“2”
Sets the CD read mode.
*
“DEMO Mode”
“OFF”/“ON”*
2 sec. Specifies whether to enable demonstration.
—
—
23
10
“SETUP”
“Display
Select”
“Type Select”
“DISP TYPE
[A] – [D]”
Sets the display pattern.
“Graphic Select” “Graphic 1 –2”
Sets the Type C spectrum analyzer display.
Sets the Type A side display.
—
—
—
—
“Side Select”
3 types
|
8
KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Category Item
Setting
Entry
Setting overview
Condition Page
“Text Select”
“Status”
—
Sets the Type A/B/C text display.
—
10
Appear/
Sets the Type A Status display.
—
—
Disappear
“Variable
Scan”*/
“Color
Select”
“All”
Sets the panel and display illumination color.
11
“Color 1”–
“Color 10”/
“User”
“Display”
“Right”
“Left”
Sets the display illumination color.
Sets the right side of panel illumination color.
Sets the left side of panel illumination color.
Sets the sound quality.
“SOUND”
“Control” “EQ”
—
27
“Bass Boost”
“OFF”*/
Sets the Bass Boost level in two steps.
—
“STEP1”/“2”
“HIGHWAY-
SOUND”
“OFF”/“STEP1”
/ “2”/“3”*
Compensates the low volume or bass sound being lost
by road noises to make vocal sound clearer.
*
*
“Supreme+”
“ON”*/“OFF”
Turns ON/OFF the Supreme plus function.
“Position”
“Cabin”
—
Compensates the sound environment in accordance
with the listening position.
28
25
25
26
26
29
“Setup”
“Compact”etc.
Selects the car type to compensate the distance
difference between each speaker.
“Speaker”
“DTA”
—
—
—
—
—
Sets the connected speaker, speaker size, and
installation position.
Makes fine adjustment of the compensation value
specified at Cabin.
“X’Over”
“Recall”
“Memory”
Makes fine adjustment of the X’Over value specified at
Speaker.
“Preset”
Registering the value setup by Sound Control. Recalling
the sound setup registered by <Audio Preset Memory>.
Registering the value setup by Sound Control.
29
“DSP Set”
“Bypass”/
Setting “BYPASS” passes the DSP function.
—
“Through”*
Setting “THROUGH” activates the DSP function.
“BT”
“Voice Recognize”
—
—
—
Calls by recognizing the registered voice.
18
34
35
“Voice Tag” “PB Name Edit”
“PN Type Edit”
Registers voice for voice recognition.
Registers voice to select the Phone number category
in Phonebook.
“SMS”
“SMS
Download”
—
—
Download a short message.
36
36
“SMS Inbox”
Display the received short message.
•
Location played with “FILE SCAN”
- Audio file: First 10 seconds
- Music Editor media: First 10 seconds or the part picked by
Intro Skip.
During Intro Skip, turn the control knob left or right to
change the song.
The scan method depends on the Music Editor setting.
See the Music Editor help for details.
⁄
•
Strong electrical fields (such as from power lines) may cause
unstable sound quality when CRSC is turned ON. In such a
situation, turn it OFF.
•
The connected cell-phone must have the SMS function to
use the “SMS” function.
English
|
9
Display Settings
Display Type Selection
Text Display Selection
Shown below are examples of display types.
Changes displayed information on each source
following;
Display
Display Type
“TYPE [A]”
“TYPE [B]”
“TYPE [C]”
“TYPE [D]”
Displays 4 to 5 lines of text.
Displays a line of text and video.
Displays a line of text and the spectrum analyzer.
Displays the clock.
In Tuner source
Information
Frequency
Spectrum analyzer & Clock (“TYPE [A]/[B]”)
or Clock (“TYPE [C]”)
Date
Blank
Display
“Frequency”
“Speana/Clock”
or“Clock”
“Date”
1 Enter Display type selection mode
Select “SETUP” > “Display Select” > “Type
Select”.
“Blank”
For how to select Function Control item, refer to
In CD & External disc source
<Function Control> (page 6).
Information
Display
Disc title
Track title
Play time
“Disc title”
“Track title”
“P-Time”
“Speana/Clock”
or“Clock”
“Date”
2 Select the Display type
Turn the Control knob.
3 Exit Display type selection mode
Spectrum analyzer & Clock (“TYPE [A]/[B]”)
or Clock (“TYPE [C]”)
Date
Blank
Press the [FNC] button.
⁄
“Blank”
•
For how to switch the text display information, refer to
<Text Display Selection> (Page 10).
In Audio file/ iPod source
Information
Title & Artist name
Album & Artist name
Folder name
•
When “TYPE [A]” is selected, the status (ON/OFF indicator
of each function) can be displayed on the first line, and
the icon of the currently selected source and the text
information title can be displayed on the left side by the
following <Function Control> (page 6) operation.
Status display: Select “SETUP” > “Display Select” > “Status”
Side display: Select “SETUP” > “Display Select” >
“Side Select”
Display
“Title/Artist”
“Album/Artist”
“Folder name”
“File name”
“P-Time”
“Time Bar”
“Speana/Clock”
or“Clock”
File name
Play time
Play time bar (iPod only)*
Spectrum analyzer & Clock (“TYPE [A]/[B]”)
or Clock (“TYPE [C]”)
Date
•
When “TYPE [C]” is selected, the spectrum analyzer can
be switched by the following <Function Control> (page
6) operation.
“Date”
“Blank”
: Select “SETUP” > “Display Select” > “Graphic Select”
Blank
* Can be displayed only on the bottom line of “TYPE [A]”
text.
In Standby/ Auxiliary input source
Information
Source name
Clock
Display
“Source Name”
“Clock”
Date
“Date”
Blank
“Blank”
1 Enter Text display selection mode
Select “SETUP” > “Display Select” >
“Text Select”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Select the text display part
Push the Control knob towards up or down.
The selected text display part blinks.
|
10 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
The color you created can be called when you
select “User”.
3 Select the text
Turn the Control knob.
1. Press the Control knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
4 Exit Text display selection mode
Press the [FNC] button.
⁄
Operation type
Operation
•
•
•
•
If the selected display item does not have any
information, alternative information is displayed.
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed.
Some items cannot be selected depending on the
display type and row.
When selecting “Folder name” while playing with
iPod, names will be displayed depending on currently
selected browsing items.
If the iPod Control by Hand Mode is set to on while
playing the iPod, “iPod by Hand Mode” is displayed.
If all characters cannot be displayed while playing with
iPod, the file number in the list is displayed.
To select the color to adjust. Push the Control knob towards right
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
or left.
Turn the Control knob or push it
towards up or down.
3. Press the Control knob.
Exit the detail color adjustment mode.
4 Exit Illumination color selection mode
Press the [FNC] button.
•
•
Information
Music title
Folder name
File name
Display
Auxiliary Input Display Setting
“TITLE***”
“FLD***”
“FILE***”
Selects the display when changing to Auxiliary
input source.
1 Select the AUX source
Press the [SRC] button.
Illumination Color Selection
2 Enter Auxiliary input display setting mode
Select “MENU” > “Name Set”.
For how to select Function Control item, refer to
Selecting the Illumination Color of the panel.
1 Enter Illumination color selection mode
Select “SETUP” > “Color Select”.
For how to select Function Control item, refer to
<Function Control> (page 6).
3 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
<Function Control> (page 6).
2 Select the place where you want to set the
Illumination Color
4 Select the Auxiliary input display
Turn the Control knob.
“AUX”/ “DVD”/ “PORTABLE”/ “GAME”/ “VIDEO”/ “TV”
Place
All
Display
“All”
Display
Right
Left
“Display”
“Right”
“Left”
5 Exit Auxiliary input display setting mode
Press the [FNC] button.
⁄
Turn the Control knob and push the center
when the desired item is displayed.
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is
displayed by default.
AUX source is initially set to “OFF”. Before display setting,
set “Built in AUX” described in <Function Control> (page
6) to “ON”.
3 Select the Illumination Color
Turn the Control knob and push the center
when the desired item is displayed.
Select the color from “Variable Scan”/ “Color1” —
“Color 10”/ “User”.
•
•
Creating “User” color
You can create your original color during the
: Select “MENU” > “Built in AUX”
selection from “Color1” — “Color10.”
English
|
11
Music disc/Audio file Operation
Function of Audio file/ Internal CD source
Function of iPod
Music Search
Music Search for iPod
Selecting the music you want to listen to from the
device or media being played now.
Search for the song (in iPod) you want to play.
1 Enter Music Search mode
1 Enter Music Search mode
Press the [ ] button.
“SEARCH” is displayed.
Press the [ ] button.
2 Search for music
Operation type
Operation
Displays the current Audio file name.
Movement between items Turn the Control knob.
2 Search for music
Skip Search *1
Push the Control knob towards right or left.
Selection of item
Return to previous item
Return to Top menu
Press the Control knob.
Audio file
Push the Control knob towards up.
Push the Control knob towards up for at
least 1 second.
Push the Control knob towards down. Refer
to the next section <Searching for Music
by Initial>.
Operation type
Movement between
folders/files
Operation
Turn the Control knob or push it towards
up or down.
Press the Control knob or push it towards
right.
Search by initial
Selection of folder/file
Return to previous folder Push the Control knob towards left.
Scroll bar is displayed on the right side of the
screen.
Return to root folder
Push the Control knob towards left for at
least 1 second.
Cancelling the Music Search mode
Press the [ ] button.
“8” or “7” beside the displayed folder name
indicates that this folder is preceded or followed by
another folder.
⁄
•
File name is displayed with “¡” indicator.
*1 Skip Search: The number of songs to be skipped is
determined by the ratio of the total number of songs
in the list which is selected now. Set the ratio with
“Skip Search” in <Function Control> (page 6). Keep
pushing Control knob for 3 seconds or longer skips
songs at 10% irrespective of the setting.
Internal CD source
Operation type
Operation
Movement between track Turn the Control knob or push it towards
up or down.
Selection of track
Press the Control knob.
•
Characters that are included in a song name but cannot
be displayed are left blank. If no character included in a
song name cannot be displayed, the browse item name
and digits are displayed.
Return to first track
Push the Control knob towards left for at
least 1 second.
Cancelling the Music Search mode
Press the [ ] button.
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
⁄
•
Music Search cannot be performed during Random play.
Function of iPod
Searching for Music by Initial
You can select an alphabetic character from the list
in the browse item (artist, album, etc.) selected now.
1 Enter Music Search mode
Press the [ ] button.
|
12 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Function of iPod
2 Start the alphabet search
Push the Control knob towards down.
“A B C …” is displayed.
iPod Control by Hand Mode
Allows you to operate iPod with the control on the
iPod.
•
If you can not search for a song by an alphabetic
character in the browse item selected now, the data on
the screen does not change.
Enter iPod Control by Hand Mode
Select “iPod BY HAND”.
For how to select Function Control items, refer to
3 Select the initial to be searched for
Operation type Operation
Move to the next character. Turn the Control knob or push it towards
right or left.
<Function Control> (page 6).
⁄
Move to the next row.
Push the Control knob towards up or
down.
•
•
•
•
iPod will be paused when Hand mode is turned ON
during playback.
In the iPod Control by hand mode, iPod cannot be
operated using this unit.
This mode is not compatible with music information
display. The display will show “iPod by Hand Mode”.
iPod can be operated when it conforms to the iPod
control function.
4 Determine the selected initial
Press the Control knob.
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
Cancelling the alphabet search
Press the [ ] button.
Function of remote control
⁄
Direct Music Search
•
The time of search by alphabet may become long
depending on the number of songs in iPod or the folder
structure.
Searchs the music by entering the track number.
•
•
When selecting an initial in the alphabet search, entering
“*” searches symbols and entering “1” searches digits.
If the first character string begins with an article “a”, “an”,
or “the” in the alphabet search mode, it is searched for in
defiance of the article.
1 Enter the music number
Press the number buttons on the remote
control.
2 Search the music
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [38] button.
⁄
Function of iPod
•
Direct Music Search cannot be performed during playing
of iPod, “Music Editor” media, Random play, or scan play.
All Random
All songs in iPod are played at random.
Enter All random mode
Select “ALL RANDOM”.
For how to select Function Control items, refer to
<Function Control> (page 6).
⁄
•
The time required to turn on the all random function
may become longer depending on the number of songs
in iPod or the folder structure.
•
Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not change
even if the all random function is turned off.
English
|
13
Music disc/Audio file Operation
Function of disc changers with remote control
Direct Disc Search
Searchs the disc by entering the disc number.
1 Enter the disc number
Press the number buttons on the remote
control.
2 Search the disc
Press the [FM+] or [AM–] button.
Cancelling Direct Disc Search
Press the [38] button.
⁄
•
Direct Disc Search cannot be performed during playing
of Random play or scan play.
•
Input “0” to select disc 10.
Basic Operation of Disc Changer
(Optional)
Selecting CD changer source
Press the [SRC] button.
Select the “CD CHANGER” display.
Music search
Push the Control knob towards right or left.
Disc Search
Push the Control knob towards up or down.
|
14 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Tuner Operation
Function of remote control
Auto Memory Entry
Direct Access Tuning
Putting stations with good reception in the memory
automatically.
Entering the frequency and tuning.
1 Enter Auto Memory Entry mode
Select “AUTO MEMORY”.
For how to select Function Control items, refer to
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
<Function Control> (page 6).
“– – – –” is displayed.
2 Open Auto Memory Entry
2 Enter the frequency
Turn the Control knob to select “YES”, and then
press the Control knob.
Press the number buttons on the remote
control.
When 6 stations that can be received are put in the
Example:
memory, auto memory entry closes.
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[0], [9], [2], [1]
[0], [8], [1], [0]
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
Station Preset Memory
Putting a station in the memory.
⁄
1 Select the frequency to put in the memory
•
You can enter the FM band frequency in steps of a
minimum of 0.1 MHz.
Push the Control knob towards right or left.
2 Enter Preset Memory mode
Press the [ ] button.
3 Select the number to put in the memory
Turn the Control knob.
Frequency Step Setting
4 Determine the number to put in the memory
Changing the tuning frequency step.
The original setting is FM band 50 kHz, and AM
band 9 kHz.
Press the Control knob for at least 2 seconds.
Cancelling the Preset Memory mode
Press the [ ] button.
1 Turn the power OFF
Press the [SRC] button for at least 1 second.
2 Switch the frequency step
While pressing the [AUD] knob and Control
knob, press the [SRC] button.
Release your fingers from the button after the
display appears.
Preset Tuning
Recalling the stations in the memory.
1 Enter Preset Tuning Select mode
The frequency step changes to FM band 200 kHz,
and AM band 10 kHz.
Press the [ ] button.
2 Select a desired station in the memory
⁄
•
Turn the Control knob.
When the same operation is repeated, the frequency
step returns to the original setting.
When the frequency step is changed, the frequencies in
the memory are deleted.
3 Recall the station
•
Press the Control knob.
Cancelling Preset Tuning
Press the [ ] button.
English
|
15
Function of KDC-XBT8013U/ KDC-XBT8013UL
KDC-X7013U/ KDC-X7013UL with KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
your cell-phone to return to the hands-free talk mode.
Before Use
Adjusting the Voice Volume during a Call
Turn the [AUD] knob.
• For details on the Bluetooth cell-phone with the
hands-free function, see <About the Cell-Phone>
(Page 41).
• You need to register your cell-phone before using
it with this unit. For more details, see <Registering
Bluetooth device> (Page 32).
• If you have registered two or more cell-phones,
you need to select one of them. For more details,
see <Selecting the Bluetooth device You Wish to
Connect> (Page 33).
Call waiting
Answering Another Incoming Call with the
Current Call Suspended
1 Press the [AUD] button.
• To use the Phone Book, it must be downloaded to
this unit in advance. For details, see <Downloading
the Phone Book> (Page 33).
• “BT” indicator is lit when a cell-phone is connected
to this unit.
2 Turn the Control knob or push it towards up
or down. Select the “ANSWER” display.
3 Press the [AUD] button.
Answering another Incoming Call after
Terminating the Current Call
Press the [SRC] button or press the [ ] button
for at least 1 second.
Receiving a call
Continuing the Current Call
Answering a Phone Call
Press the [AUD] button.
1 Press the [AUD] button.
2 Turn the Control knob or push it towards up
⁄
or down. Select the “REJECT” display.
•
The following operations disconnect the line:
- Insert a CD.
3 Press the [AUD] button.
Answering the Waiting Call after Terminating
the Current Call
- Connect a USB device.
•
The name of the calling party is displayed if it has already
been registered in the Phone Book.
Press the [SRC] button or press the [ ] button
for at least 1 second.
Rejecting an Incoming Call
Press the [SRC] button or press the [ ] button
for at least 1 second.
Switching between the Current Call and Waiting
Call
Press the [AUD] button.
Each pressing of this knob switches the calling
party.
During a call
Disconnecting a Call
Press the [SRC] button or press the [ ] button
for at least 1 second.
Other functions
Switching to the Private Mode
Press the Control knob.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
Clearing the Disconnection Message
KDC-XBT8013U/ KDC-XBT8013UL:
Press the [ ] button.
KDC-X7013U/ KDC-X7013UL:
Press the [ ] button for at least 1 second.
“HF Disconnect” disappears.
⁄
•
Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
|
16 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Making a call
Speed dialing (Preset dial)
1 Enter dialing method mode
KDC-XBT8013U/ KDC-XBT8013UL:
Press the [ ] button.
1 Enter dialing method mode
KDC-XBT8013U/ KDC-XBT8013UL:
Press the [ ] button.
KDC-X7013U/ KDC-X7013UL:
KDC-X7013U/ KDC-X7013UL:
Press the [ ] button for at least 1 second.
Press the [ ] button for at least 1 second.
2 Press the Control knob.
2 Select a dialing method
Select the “DIAL”, “PHONE BOOK”, “OUT-CALL”,
“IN-CALL”, or “MISSED CALLS” display.
Press the Control knob.
“DIAL” » “INITIAL” » “PHONE BOOK” » “OUT-CALL” »
“IN-CALL” » “MISSED CALLS”
Methods of operations in the above modes are
described below.
3 Enter preset dial mode
Press the [ ] button.
4 Select the number you want to recall from the
3 Exit the dialing method mode
memory
Press the [ ] button.
Turn the Control knob or push it towards up or
down.
5 Press the Control knob.
Phone number is displayed.
Dial a number
6 Exit preset dial mode
Press the [ ] button.
1 Enter dialing method mode
KDC-XBT8013U/ KDC-XBT8013UL:
Press the [ ] button.
KDC-X7013U/ KDC-X7013UL:
Press the [ ] button for at least 1 second.
7 Make a call
Press the Control knob for at least 1 second.
⁄
•
You need to register the preset dial number. (Page 19)
2 Select the number dial mode
Press the Control knob.
Select the “DIAL” display.
3 Enter a phone number
Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
4 Make a call
Press the [DIRECT] button on the remote
controller.
To erase the entered phone number digit by
digit:
Press the [4] button on the remote controller.
⁄
•
You can input max 32 digits.
English
|
17
Function of KDC-XBT8013U/ KDC-XBT8013UL
KDC-X7013U/ KDC-X7013UL with KCA-BT200 (Optional Accessory)
Operation of hands-free phoning
Calling a number in the Phone Book
Calling a number in the call log
1 Enter dialing method mode
KDC-XBT8013U/ KDC-XBT8013UL:
Press the [ ] button.
KDC-X7013U/ KDC-X7013UL:
Press the [ ] button for at least 1 second.
1 Enter dialing method mode
Press the [ ] button.
2 Select the call log mode
Press the Control knob.
Select the “OUT-CALL” (outgoing call), “IN-CALL”
(incoming call), or “MISSED CALLS” (missed call)
display.
2 Select the Phone Book mode
Press the Control knob.
Select the “INITIAL” display, proceed to step 3.
Select the “PHONE BOOK” display, proceed to step
4.
3 Select a name or phone number
Turn the Control knob or push it towards up or
down.
3 Select the initial to be searched for
Switching between Display Modes
Press the [FNC] button.
Pressing this button each time switches between
Operation type
Operation
Move to the next character. Turn the Control knob or push it towards
right or left.
name and telephone number.
Move to the next row.
Push the Control knob towards up or
down.
4 Make a call
Press the Control knob for at least 1 second.
Determine the selected initial. Press the Control knob.
⁄
4 Select the name
Operation type
Move to the next phone
number.
•
The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
Operation
Turn the Control knob or push it
towards up or down.
Push the Control knob towards right
or left.
Move to the next name.
Switching between Display Modes
Press the [FNC] button.
Pressing this button each time switches between
Make a voice dialing call
1 Enter voice recognize mode
Select “BT” > “Voice Recognize”.
For how to select Function Control item, refer to
<Function Control> (page 6).
name and telephone number.
5 Make a call
Press the Control knob for at least 1 second.
⁄
“Ready” is displayed.
•
During search, a non-accent character such as “u” is
searched for instead of an accent character such as “ü”.
2 Press the Control knob.
“PB Name?” is displayed.
When a beep is heard, utter the name within 2
second.
3 “PN Type” is displayed.
When a beep is heard, utter the category within 2
second.
4 Make a call
Press the Control knob for at least 1 second.
•
This step is the same as step 3 of the procedure in
<Calling a number in the Phone Book>. You can make a
call or select a category.
|
18 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
⁄
•
If your voice cannot be recognized, a message is
displayed. Pressing the Control knob allows you to retry
voice input. (Page 48)
•
•
Both the name and category requires registration of a
voice tag. (Page 34)
Audio sound is not output during voice recognize.
Registering to the Preset Dial Number
List
1 Enter the phone number you wish to register
Enter the phone number with reference to the
following:
Dial a number/ Calling a number in the call log/
Calling a number in the Phone Book
2 Enter Preset Memory mode
Press the [ ] button.
3 Select the number to put in the memory
Turn the Control knob or push it towards up or
down.
4 Determine the number to put in the memory
Press the Control knob for at least 1 second.
Exit the Preset Memory mode
Press the [ ] button.
Display of phone number type
(category)
The category items in the Phone Book are displayed
as follows:
Display
Information
“GENERAL”/“
”
General
“HOME”/“
“OFFICE”/“
“MOBILE”/“
“OTHER”/“
”
Home
Office
Mobile
Other
”
”
”
English
|
19
Bluetooth Audio Operation
Before Use
• For details on the Bluetooth Audio player which
can be connected, see <About the Bluetooth Audio
player> (Page 41).
• You need to register your Bluetooth Audio player
before using it with this unit. For more details, see
<Registering Bluetooth device> (Page 32).
• You to select the Bluetooth audio player you wish to
connect. Refer to <Selecting the Bluetooth device
You Wish to Connect> (Page 33).
Basic Operation
Selecting Bluetooth Audio source
Press the [SRC] button.
Select the “BT Audio” display.
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
Pause and play
Press the Control knob.
Music Search
Push the Control knob towards right or left.
⁄
•
•
•
All or some of the operations above cannot be
performed if the Bluetooth audio player is not ready for
remote control.
Switching between Bluetooth audio sources does
not start or stop playback automatically. Perform the
operation for starting or stopping playback.
Some audio players cannot be controlled remotely or
reconnected after Bluetooth disconnection. Operate the
main unit of the audio player to connect Bluetooth.
|
20 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Other Functions
Activating Security Code
Deactivating Security Code
To deactivate the Security Code function.
⁄
•
You can set the Security Code with a 4 digit number of your
choice.
1 Select Security code mode
Select “MENU” > “Security Clear”.
For how to select Function Control items, refer to
<Function Control> (page 6).
•
The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
1 Select Security code mode
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When “Enter” is displayed, “[–][–][–][–]” is also
displayed.
Select “MENU” > “Security Set”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When “Enter” is displayed, “[–][–][–][–]” is also
displayed.
3 Enter Security Code
Operation type
Operation
Push the Control knob towards right
or left.
Turn the Control knob or push it
towards up or down.
Select the digits to enter
3 Enter Security Code
Select the Security Code
numbers
Operation type
Operation
Select the digits to enter
Push the Control knob towards right
or left.
Turn the Control knob or push it
towards up or down.
4 Press the Control knob for at least 3 seconds.
“Clear” is displayed.
The Security Code function deactivates.
Select the Security Code
numbers
5 Exit Security Code mode
4 Confirm the Security Code
Press the Control knob for at least 3 seconds.
When “Re-Enter” is displayed, “[–][–][–][–]” is also
displayed.
Press the [FNC] button.
5 Do the step 3 through 4 operation, and reenter
the Security Code.
“Approved” is displayed.
The Security Code function activates.
⁄
•
If you enter the wrong Code in steps 3 through 4, repeat
from step 3.
6 Exit Security Code mode
Press the [FNC] button.
Entering Security Code
The Security Code is required to use the audio unit
when the unit is first used after removed from the
battery power source or the Reset button is pressed.
1 Turn the power ON.
2 Do the step 3 through 4 operation, and enter
the Security Code.
“Approved” is displayed.
Now, you can use the unit.
English
|
21
Other Functions
Manual Clock Adjustment
Date Format Selection
1 Select Clock adjustment mode
Select “MENU” > “Clock Adjust”.
For how to select Function Control items, refer to
<Function Control> (page 6).
1 Select Date format mode
Select “MENU” > “Date Mode”.
For how to select Function Control items, refer to
<Function Control> (page 6).
2 Enter Clock adjustment mode
Press the Control knob for at least 1 second.
The clock display blinks.
2 Enter Date format mode
Press the Control knob for at least 1 second.
The date is displayed.
3 Adjusting Clock
Operation type
Selecting the item (hours or
minutes)
3 Adjusting Date
Turn the Control knob.
Select from 7 types.
Operation
Push the Control knob towards right
or left.
Turn the Control knob or push it
towards up or down.
4 Exit Date format mode
Adjust each item
Press the [FNC] button.
4 Exit Clock adjustment mode
Press the [FNC] button.
When LX AMP unit connecting
AMP Control
You can control the LX AMP connected to the unit.
Date Adjustment
1 Select AMP Control mode
1 Select Date adjustment mode
Select “MENU” > “Date Adjust”.
For how to select Function Control items, refer to
Select “MENU” > “AMP Control”.
For how to select Function Control items, refer to
<Function Control> (page 6).
<Function Control> (page 6).
2 Enter AMP Control mode
2 Enter Date adjustment mode
Press the Control knob for at least 1 second.
The date display blinks.
Press the Control knob for at least 1 second.
3 Select the AMP Control item for adjustment
Turn the Control knob or push it towards up or
down.
3 Adjusting Date
⁄
Operation type
Selecting the item (month, day, Push the Control knob towards right
Operation
•
For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
or year)
or left.
Adjust each item
Turn the Control knob or push it
towards up or down.
4 Adjust the AMP Control item
Push the Control knob towards right or left.
4 Exit Date adjustment mode
5 Exit AMP Control mode
Press the [FNC] button.
Press the [FNC] button.
|
22 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Demonstration mode setting
Theft Deterrent Faceplate
Turning the demonstration mode ON/OFF.
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
1 Select Demonstration mode
Select “MENU” > “DEMO Mode”.
For how to select Function Control items, refer to
<Function Control> (page 6).
Removing the Faceplate
1 Press the Release button.
Drop open the faceplate.
2 Set the Demonstration mode
2 Drawing the faceplate to left side pull it to
Press the Control knob for at least 2 seconds.
Pressing this button for 2 seconds or longer toggles
the setting between “ON” and “OFF”.
forward and remove it.
3 Exit Demonstration mode
Press the [FNC] button.
¤
•
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
•
•
Keep the faceplate in its faceplate case while detached.
Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
1 Align the shaft on the unit with the depression
on the faceplate.
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use
the unit.
English
|
23
Audio Adjustments
Audio Control
Audio Setup
You can adjust following Audio Control items;
You can set Sound system , such as follows;
Adjustment Item Display
Range
0 — 35
Adjustment Item Display
Volume offset
Dual Zone System
Range
“VOL-OFFSET” –8 — 0 (AUX: -8— +8)
“2 ZONE” OFF/ON
Rear volume
Subwoofer level
Balance
“REAR VOLUME”
“SUBWOOFER LEVEL” –15 — +15
“BALANCE”
“FADER”
Left 15 — Right 15
Rear 15 — Front 15
⁄
Fader
Exit Audio Control mode (Volume control mode)
•
Volume offset: Sets each source’s volume as a difference
from the basic volume.
•
Dual Zone System
1 Enter Audio Control mode
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by “Zone2” of
<Function Control> (page 6).
Press the [AUD] knob.
2 Select the Audio item to adjust
Press the [AUD] knob.
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [AUD] knob.
- Adjust the volume of Rear channel by <Audio Control>
(Page 24) or [5]/[∞] button on the remote control
(Page 38).
3 Adjust the Audio item
Turn the [AUD] knob.
4 Exit Audio Control mode
Press any button.
Press a button other than the [AUD] knob or [0]
button.
- The Audio Control has no effect on sub source.
1 Select the source to adjust
Press the [SRC] button.
2 Enter Audio Setup mode
Press the [AUD] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [AUD] knob.
4 Adjust the Audio setup item
Turn the [AUD] knob.
5 Exit Audio Setup mode
Press the [AUD] knob for at least 1 second.
|
24 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Sound Setup
Cabin selection
1 Enter Speaker setting mode
Select “SOUND” > “Setup” > “Speaker”.
For how to select Function Control item, refer to
<Function Control> (page 6).
You can compensate the delay of the sound arrival
time by selecting your environment from the
following car types;
2 Select the speaker you want to set
Car type
Display
“OFF”
Setting speaker
Front speaker
Rear speaker
Subwoofer
Display
“FRONT”
“REAR"
Not compensating.
Compact car
Full size car
Station wagon
Minivan
“Compact”
“Full Size Car”
“Wagon”
“Minivan”
“SUV”
“SUB W"
Turn the Control knob.
Sport-utility vehicle
Long Minivan
3 Select the item you want to set
“Minivan (Long)”
Item
Setting overview
Speaker Size Front
>“LOCATION” Speaker Location Front
>“TWEETER” Speaker Select Tweeter
1 Enter Cabin select mode
“FRONT” >“SIZE”
Select “SOUND” > “Setup” > “Cabin”.
For how to select Function Control item, refer to
<Function Control> (page 6).
“REAR"
>“SIZE”
>“LOCATION” Speaker Location Rear
“SUB W" >“SIZE” Speaker Size Subwoofer
Speaker Size Rear
2 Select the car type
Turn the Control knob and push the center
when the desired item is displayed.
Exit Cabin select mode.
Push the Control knob towards up or down.
4 Set the value
Turn the Control knob.
⁄
•
You can compensate the distances in more details by
using <DTA> (page 26) function.
5 Repeat steps 2 to 4 to complete the speaker
settings.
6 Exit Speaker setting mode
Press the [FNC] button.
Speaker setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items;
Item
Range
Speaker Size Front
“O.E.M.”,“10cm”,“13cm”,“16cm”,“17cm”,
“18cm”,“4x6”,“5x7”,“6x8”,“6x9”,“7x10”
Speaker Location Front
Speaker Size Tweeter
Speaker Size Rear
“Door”, “On Dash”, “Under Dash”
“None”, “Use”
“None”, “O.E.M.”,“10cm”,“13cm”,“16cm”,
“17cm”,“18cm”,“4x6”,“5x7”,“6x8”,
“6x9”,“7x10”
Speaker Location Rear
Speaker Size Subwoofer
“Door”, “Rear Deck”
“Minivan”, “Minivan (Long)”:
“2nd Row”, “3rd Row”
“None”, “16cm”, “20cm”, “25cm”, “30cm”,
“38cm Over”
English
|
25
Sound Setup
DTA (Digital Time Alignment) setting
X’Over setting
Adjusting fine tuning of the speaker position
compensation value specified at <Cabin selection>
(Page 25).
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (Page 25);
Adjustment Item Display
Front High Pass Filter, “FC”
Rear High Pass Filter
Range
1 Enter DTA setting mode
Through, 30, 40, 50, 60, 70,
80, 90, 100, 120, 150, 180,
220, 250 (Hz)
Select “SOUND” > “Setup” > “DTA”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Front High Pass Slope, “SLOPE”
Rear High Pass Slope,
Subwoofer Slope
Subwoofer Low Pass “FC”
Filter
-6, -12, -18, -24 dB/Oct
2 Select the speaker you want to set
Setting speaker
Front speaker
Rear speaker
Subwoofer
Display
“Front”
“Rear"
“SW"
30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250,
Through (Hz)
Subwoofer Phase
“PHASE”
Reverse (180°)/ Normal (0°)
Turn the Control knob.
1 Enter X’Over setting mode
3 Set the compensation value of the speaker
position
Turn the Control knob and push the center
when the desired value is displayed.
Adjust between 0 and 440 cm.
Select “SOUND” > “Setup” > “X’Over”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Select the speaker you want to set
Setting speaker
Front speaker
Rear speaker
Subwoofer
Display
“Front”
“Rear"
Refer to “DTA” of <Menu Glossary> (Page 42) on
how to set the compensation value.
Exit DTA setting mode.
“Subwoofer"
Turn the Control knob and push the center
when the desired item is displayed.
3 Select the item you want to set
Item
Setting overview
“Front”
>“FC”
Front High Pass Filter
>“SLOPE” Front High Pass Slope
>“FC” Rear High Pass Filter
>“SLOPE” Rear High Pass Slope
“Subwoofer" >“FC” Subwoofer Low Pass Filter
“Rear"
>“SLOPE” Subwoofer Slope
>“PHASE” Subwoofer Phase
Push the Control knob towards up or down.
4 Set the X’Over value
Turn the Control knob.
5 Repeat steps 2 to 4 to complete the X’Over
setting.
6 Exit X’Over setting mode
Press the [FNC] button.
|
26 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Preset Equalizer curve select
Manual Equalizer Control
You can select following Equalizer curve;
You can adjust following Equalizer Control items;
Equalizer curve
Natural
User*
Rock
Pops
Easy
Top 40
Jazz
Display
“Natural”
“User”
“Rock”
“Pops”
“Easy”
“Top 40”
“Jazz”
“Game”
“iPod”
Adjustment Item
Band 1
Band 2
Band 3
Band 4
Band 5
Band level
Bass Effect*
Display Range
“BAND1”
“BAND2”
“BAND3”
“BAND4”
“BAND5”
“GAIN”
62.5 Hz
250 Hz
1 kHz
4 kHz
16 kHz
-9 –+9 dB
“ON”/“OFF”
“EFCT”
Game
*Can be only set for “BAND1”.
iPod (During iPod source only)
1 Enter Manual Equalizer Control mode
Select “SOUND” > “Control” > “EQ” >
“Manual Equalizer”.
For how to select Function Control item, refer to
<Function Control> (page 6).
* The Equalizer curve set in the section <Manual Equalizer
Control> is recalled.
1 Enter Preset Equalizer mode
Select “SOUND” > “Control” > “EQ” >
“Preset Equalizer”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Select the band you want to set
Turn the Control knob.
2 Select the Equalizer curve
3 Select the item you want to set
Turn the Control knob and push the center
when the desired item is displayed.
You can select from 22 Equalizer curve types for
iPod when “iPod” is selected.
Push the Control knob towards up or down.
Move the cursor “>” to the desired item.
4 Set the value
Turn the Control knob.
Exit Preset Equalizer mode.
Select the iPod Equalizer curve
1. Enter iPod Equalizer mode
5 Repeat steps 2 to 4 to complete the Equalizer
curve.
Press the Control button.
To change the band, move the cursor “>” to “band#”.
2. Select the iPod Equalizer curve
Turn the Control knob and push the center
when the desired item is displayed.
Exit Preset Equalizer mode.
6 Exit Manual Equalizer Control mode
Press the [FNC] button.
⁄
•
When “iPod” is selected in the section <Preset Equalizer
curve select> (Page 27), Manual Equalizer Control is
disabled.
⁄
•
You can select for each source.
•
You can select for each source.
English
|
27
Sound Setup
Preset position selection
Manual position setting
According to the listening position, select the
position from the following settings so that the
normal position of the sound environment can
be compensated in accordance with the selected
position;
Making fine adjustment of the value specified at
Preset position selection per speaker.
1 Enter Manual position setting mode
Select “SOUND” > “Control” > “Position” >
“Manual Position”.
Compensation seat
Not compensating.
Front-Left seat
Front-Right seat
Front seat
Range
“ALL”
“Front-Left”
“Front-Right”
“Front”
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Select the speaker you want to set
Item
Setting overview
Front Left speaker
Front Right speaker
Rear Left speaker
Rear Right speaker
Subwoofer Left
“FRONT”/“L”
“FRONT”/“R”
“REAR”/“L”
“REAR /“R”
“SUBWOOFER”/“L”
1 Enter Preset position setting mode
Select “SOUND” > “Control” > “Position” >
“Preset Position”.
For how to select Function Control item, refer to
“SUBWOOFER”/“R” Subwoofer Right
<Function Control> (page 6).
“INITIAL”
Initialize the setting values.
2 Select the seat you want to compensate
Turn the Control knob.
Push the Control knob towards up or down.
3 Exit Preset position setting mode
3 Set the value
Press the [FNC] button.
Turn the Control knob.
Adjust between 0 and 170 cm.
Press the Control knob for at least 1 second if you
want to execute the “INITIAL”.
4 Exit Manual position setting mode
Press the [FNC] button.
|
28 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Audio Preset Memory
Audio Preset Recall
Registering the value setup by Sound Control.
Recalling the sound setup registered by <Audio
Preset Memory> (Page 29).
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
1 Select the source
Press the [SRC] button.
- Cabin selection (Page 25)
- Speaker Setting (Page 25)
2 Enter Audio preset recall mode
Select “SOUND” > “Preset” > “Recall”.
For how to select Function Control items, refer to
<Function Control> (page 6).
- DTA (Digital Time Alignment) setting (Page 26)
- X’Over setting (Page 26)
- Manual Equalizer Control (Page 27)
- Preset position selection (Page 28)
- Manual position setting (Page 28)
3 Select the number to recall in the memory
Turn the Control knob and push the center
when the desired number is displayed.
2 Enter Audio preset memory mode
Select “SOUND” > “Preset” > “Memory”.
For how to select Function Control items, refer to
<Function Control> (page 6).
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Recall Completed” is displayed.
5 Exit Audio preset recall mode
3 Select the number to put in the memory
Turn the Control knob and push the center
when the desired number is displayed.
Press the [FNC] button.
⁄
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Memory Completed” is displayed.
•
The “User” of <Preset Equalizer curve select> (Page 27) is
changed to the value which was recalled.
•
The Equalizer curve is changed to the value which was
recalled by the selected source.
5 Exit Audio preset memory mode
Press the [FNC] button.
⁄
•
•
Register 6 pairs of Audio Preset Memory.
Number “1”: When you press the Reset, all the sources
will be the setting value which is registered.
Number “1” and “2”:
The memory cannot be erased by the Reset button.
This function cannot be registered when the iPod
Equalizer set in <Preset Equalizer curve select> (Page 27).
•
•
English
|
29
Favorite Control
Favorite Preset Memory
Favorite Preset Recall
Registering the operation procedure to select your
favorite broadcast station or iPod Playlists/ Artists,
etc.
Retrieving an item registered to Favorite.
1 Enter Favorite Preset Recall mode
Turn the Control knob.
1 Display a favorite item
2 Select the number to recall in the Favorite
memory
Turn the Control knob.
Source
TUNER
iPod
Registerable items
Preset Memory
List selection screen for Playlists/ Artists/
Albums, etc.
3 Recall the Favorite Preset
Press the Control knob.
Hands-free phone
Telephone number retrieval.
Cancelling the Favorite Preset Recall mode
Turn the Control knob to select “Return”, and
then press the Control knob.
“
”
is displayed when the operation procedure
FAV
can be registered.
iPod setting
The desired list in the first hierarchy can be registered.
⁄
1st hierarchy
PLAYLISTS
ARTISTS
2nd hierarchy
3rd hierarchy
iPod
•
When iPod is selected for the source, the list selection
screen for Playlists/ Artists/ Albums, etc. is displayed.
Songs will not be automatically played.
ALL ARTISTS
ARTISTS 1
ARTISTS 2
ARTISTS 3
ALBUMS
ALL ALBUMS
ALBUM 1
ALBUM 2
COMPOSERS
AUDIOBOOKS
ALBUM 3
Favorite Preset Memory Delete
Deleting an item registered to Favorite.
2 Enter Favorite Preset Memory mode
1 Enter Favorite Preset Memory Delete mode
Select “MENU” > “Favorite Delete”.
For how to select Function Control item, refer to
Press the [ ] button for at least 1 second.
3 Select the number to put in the memory
Turn the Control knob.
<Function Control> (page 6).
4 Put the Favorite Preset in the memory
2 Enter Favorite Preset Memory Delete mode
Press the Control knob.
Press the Control knob for at least 1 second.
Cancelling the Favorite Preset Memory mode
Press the [ ] button.
3 Select the number you want to delete
Turn the Control knob and push the center
when the desired number is displayed.
“Delete?” is displayed.
⁄
•
•
•
Registering the operation procedure to an existing
preset number overwrites the existing procedure.
Register 6 pairs of Favorite Preset Memory.
Select “ALL” if you want to delete all.
4 Turn the Control knob to select “YES”, and then
press the Control knob.
“Completed” is displayed.
The memory cannot be erased by the Reset button.
The same memory storage operation can be used for
“MENU”, “SETUP”, and “SOUND” in the section <Function
Control> (page 6).
Exit Favorite Preset Memory Delete mode.
However, some currently selected sources cannot be
recalled. For information on available sources, refer to
Condition column in the section <Function Control>.
If the items in the second or lower hierarchy are
changed, the list in iPod will be changed by adding or
deleting songs after the FAVORITE registration. Due to
this, the list registered in this unit will be different from
the list in iPod. The FAVORITE registration should be
performed again after editing the items in iPod.
•
|
30 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Favorite Name Setting
Giving a name to Preset Memory registered to
Favorite.
1 Enter Preset Recall mode
Turn the Control knob.
2 Retrieve the Preset Memory to change
Turn the Control knob.
3 Enter Favorite Name set mode
Press the Control knob for at least 1 second.
Select the “FAVORITE NAME SET” display.
4 Enter the name
Operation type
Operation
Move the cursor to the enter
character position
Push the Control knob towards right
or left.
Select the character type*
Select the characters
Press the Control knob.
Turn the Control knob or push it
towards up or down.
* Each time you press the knob, the character type
alternates between the types shown in the table below.
Character type
Alphabet upper case
Alphabet lower case
Numbers and symbols
5 Exit Favorite Name Set mode
Push the Control knob towards right or left
to select “ENTER”, and then press the Control
knob.
Cancelling the Favorite Name set
Press the [FNC] button.
English
|
31
Function of KDC-XBT8013U/ KDC-XBT8013UL
KDC-X7013U/ KDC-X7013UL with KCA-BT200 (Optional Accessory)
Bluetooth Setup
Press the [FNC] button.
Registering Bluetooth device
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to five Bluetooth devices to this unit.
⁄
•
This unit allows up to eight digits to be input for a PIN
code. If a PIN code cannot be input from this unit, it can
be input from the Bluetooth device.
•
•
If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
If the error message appears even though the PIN code
is correct, try <Registering Special Bluetooth device>
(Page 32).
When registering from Bluetooth devices
1 Turn on the control unit.
2 Start registering a unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD BT
CD/R-2P2”/ “KENWOOD BT200” from the list of
connected units.
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
3 Enter a PIN code
Input the PIN code registered as mentioned in
<Registering PIN Code> (Page 32).
Check that registration is complete on the
Bluetooth device.
1 Select Special device registration mode
Select “MENU” > “SPCL DVC Select”.
For how to select Function Control item, refer to
<Function Control> (page 6).
4 By operating the Bluetooth device, start hands-
free connection.
2 Enter Special device registration mode
Press the Control knob for at least 1 second.
A list is displayed.
When registering from this unit
1 Select Bluetooth device registration mode
Select “MENU” > “Device Regist”.
For how to select Function Control item, refer to
3 Select a device name
Turn the Control knob and push the center
when the desired device name is displayed.
If “Completed” is displayed, registration is
completed.
<Function Control> (page 6).
2 Enter Bluetooth device registration mode
Press the Control knob for at least 1 second.
Search for the Bluetooth device.
4 Go through the procedure of <Registering
Bluetooth device> (Page 32) and complete the
registration (pairing).
When search is completed, “Finished” is displayed.
3 Select the Bluetooth device
Cancelling Special device registration mode
Press the [FNC] button for at least 1 second.
Turn the Control knob and push the center
when the desired Bluetooth device is displayed.
⁄
4 Input the PIN code
•
If the device name is not in the list, select “Other Phones”.
Operation type
Operation
Select the numbers.
Turn the Control knob or push it towards
up or down.
Move to the next digit.
Delete the last digit.
Push the Control knob towards right.
Push the Control knob towards left.
Registering PIN Code
By operating the Bluetooth device, specify the PIN
code necessary for registering this unit.
5 Transmit the PIN code
Press the Control knob for at least 1 second.
If “Pairing Success” is displayed, registration is
completed.
1 Select PIN code edit mode
Select “MENU” > “PIN Code Edit”.
For how to select Function Control item, refer to
<Function Control> (page 6).
6 Return to the device list
Press the Control knob.
2 Enter PIN code edit mode
7 Exit Bluetooth device registration mode
|
32 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Press the Control knob for at least 1 second.
The current setting of PIN code is displayed.
3 By operating the cell-phone, start the hands-
free connection.
3 Input the PIN code
Operation type
To clear the downloading completion message
Press any button.
Operation
Select the numbers.
Turn the Control knob or push it towards
up or down.
Push the Control knob towards right.
Push the Control knob towards left.
⁄
•
Up to 1000 phone numbers can be registered for each
registered cell-phone.
Move to the next digit.
Delete the last digit.
•
Up to 32 digits can be registered for each phone number
along with up to 50* characters representing a name.
(* 50: Number of alphabetic alphabetical characters.
Fewer characters can be input depending on the type
of characters.)
4 Register a PIN code
Press the Control knob for at least 1 second.
If “Completed” is displayed, registration is
completed.
•
To cancel downloading of the phone book data, operate
the cell-phone.
5 Exit PIN code edit mode
Press the [FNC] button.
⁄
Selecting the Bluetooth device You
Wish to Connect
•
•
By default, “0000” is specified.
A PIN code can be specified with up to eight digits.
When two or more Bluetooth devices have already
been registered, you need to select the Bluetooth
device you wish to use.
Downloading the Phone Book
1 Select Bluetooth device selection mode
Cell-phone
Select “MENU” > “Phone Selection”.
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
Audio player
Select “MENU” > “Audio Selection”.
For how to select Function Control item, refer to
<Function Control> (page 6).
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone book is
downloaded automatically after Bluetooth
connection.
2 Enter Bluetooth device selection mode
Press the Control knob for at least 1 second.
“(name)” is displayed.
⁄
•
•
Setting on the cell-phone may be required.
If no phone book data is found in the unit even after
the compete display, your cell-phone may not support
automatic download of phone book data. In this case, try
downloading manually.
3 Select the Bluetooth device
Turn the Control knob.
4 Set up the Bluetooth device
Push the Control knob towards right or left.
“✱(name)” or “-(name)” is displayed.
To download from the cell-phone manually
“✱”: The selected Bluetooth device is busy.
“-”: The selected Bluetooth device is on standby.
“ “ (blank): The Bluetooth device is deselected.
1 By operating the cell-phone, end the hands-free
connection.
2 By operating the cell-phone, send the phone
book data to this unit
By operating the cell-phone, download the phone
5 Exit Bluetooth device selection mode
Press the [FNC] button.
book data to this unit.
• During downloading:
⁄
•
If a cell-phone is already selected, deselect it, and then
select a different one.
If you cannot select a device using the audio player,
connect the device with the audio player.
“Downloading” is displayed.
• After completion of downloading:
“Completed” is displayed.
•
English
|
33
Function of KDC-XBT8013U/ KDC-XBT8013UL
KDC-X7013U/ KDC-X7013UL with KCA-BT200 (Optional Accessory)
Bluetooth Setup
Deleting a Registered Bluetooth
device
Adding a voice dialing command
Add a voice tag to the phonebook for voice dialing.
You can register up to 35 voice tags.
You can delete a registered Bluetooth device.
1 Select Phonebook name edit mode
Select “BT” > “Voice Tag” > “PB Name Edit”.
For how to select Function Control item, refer to
<Function Control> (page 6).
1 Select Bluetooth device deletion mode
Select “MENU” > “Device Delete”.
For how to select Function Control item, refer to
<Function Control> (page 6).
2 Enter Phonebook name edit mode
2 Enter Bluetooth device deletion mode
Press the Control knob for at least 1 second.
“(name)” is displayed.
Press the Control knob.
3 Search for the name to register
Select the name to register with reference to 4 in
<Calling a number in the Phone Book> (Page 18).
If a voice tag has already been registered for a
name, “*” is displayed before the name.
3 Select the Bluetooth device
Turn the Control knob.
4 Delete the selected Bluetooth device
Press the Control knob.
4 Select a mode
5 Turn the Control knob to select “YES”, and then
press the Control knob.
“Delete” is displayed.
Turn the Control knob.
Display
Operation
“PB Name Regist”
“PB Name Check”*
“PB Name Delete”*
“Return”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 2.
6 Exit Bluetooth device deletion mode
Press the [FNC] button.
⁄
•
When a registered cell-phone is deleted, its Phone Book,
log, SMS, and voice tag are also deleted.
* Displayed only when a name for which a voice tag has
been registered is selected.
Select “PB Name Regist” (Regist)
5 Register a voice tag (first)
Press the Control knob.
Displaying the Firmware Version
“Enter Voice 1” is displayed.
When a beep is heard, utter a voice tag within 2
seconds.
Display the version of the firmware of this unit.
1 Enter Bluetooth Firmware update mode
Select “MENU” > “BT F/W Update”.
For how to select Function Control item, refer to
6 Confirm the voice tag (second)
Press the Control knob.
“Enter Voice 2” is displayed.
<Function Control> (page 6).
When a beep is heard, utter the same voice tag as
that you uttered in step 4 within 2 seconds.
“Completed” is displayed.
2 Enter Bluetooth Firmware update mode
Press the Control knob for at least 1 second.
The firmware version appears.
7 End registration
3 Exit Bluetooth Firmware update mode
Press the Control knob.
Return to step 2. You can register another voice tag
continuously.
Press the [FNC] button.
⁄
•
For how to update the firmware, access our web site.
⁄
•
If your voice cannot be recognized, a message is
displayed. Pressing the [AUD] knob allows you to retry
voice input. (Page 48)
Select “PB Name Check” (Play)
5 Press the Control knob.
Play the registered voice and return to step 2.
|
34 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Select “PB Name Delete” (Delete)
Setting a Voice Command for
Category
5 Delete a voice tag
Press the Control knob.
Add a voice tag to the phone number category
(type) for voice calling.
6 Turn the Control knob to select “YES”, and then
press the Control knob.
1 Select Phone Number type edit mode
Select “BT” > “Voice Tag” > “PN Type Edit”.
For how to select Function Control item, refer to
<Function Control> (page 6).
Exit Phonebook name edit mode
Press the [FNC] button.
⁄
•
Audio sound is not output during voice tag registration.
2 Enter Phone Number type edit mode
Press the Control knob.
3 Select the category (type) you wish to set
Turn the Control knob and push the center
when the desired category name is displayed.
“General”/ “Home”/ “Office”/ “Mobile”/ “Other”
4 Select a mode
Turn the Control knob.
Display
Operation
“PN Type Regist”
“PN Type Check”*
“PN Type Delete”*
“Return”
Register a voice tag.
Play a voice tag.
Delete a voice tag.
Return to step 2.
* Displayed only when a name for which a voice tag has
been registered is selected.
5 Register the category (type) by performing
steps 5 to 7 in <Adding a voice dialing
command> (Page34).
6 Exit Phone Number type edit mode
Press the [FNC] button.
⁄
•
Set the voice tag for all the 5 categories. If the voice tag
is not registered for all the categories, the Phonebook
may not be recalled by voice command.
English
|
35
Function of KDC-XBT8013U/ KDC-XBT8013UL
KDC-X7013U/ KDC-X7013UL with KCA-BT200 (Optional Accessory)
Bluetooth Setup
SMS (Short Message Service)
Downloading the SMS
The SMS arrived at the cell-phone is displayed on
the receiver.
Download the short message (SMS) arrived at the
cell-phone so that it can be read on this unit.
A newly arrived message is displayed.
1 Select SMS download mode
¤
Select “BT” > “SMS” > “SMS Download”.
For how to select Function Control item, refer to
<Function Control> (page 6).
•
To prevent car accidents, the driver should not read the
SMS while driving.
When a new message arrives
“SMS Received” is displayed.
The display disappears with any operations.
2 Enter SMS download mode
Press the Control knob.
A message list appears.
Displaying the SMS
3 Start downloading
Press the Control knob.
1 Select SMS Inbox mode
“SMS Downloading” is displayed.
When the downloading finishes, “Completed” is
displayed.
Select “BT” > “SMS” > “SMS Inbox”.
For how to select Function Control item, refer to
<Function Control> (page 6).
4 Exit SMS download mode
2 Enter SMS Inbox mode
Press the Control knob.
A message list appears.
Press the [FNC] button.
⁄
•
The cell-phone must be able to transmit the SMS using
Bluetooth. Setting on the cell-phone may be required.
If the cell-phone does not support SMS function, the
SMS download item in Function Control mode is not
displayed.
3 Select a message
Turn the Control knob.
Each pushing of the Control knob towards right or
left switches between telephone number or name
and message reception date.
•
•
When the SMS is downloaded from the cell-phone, the
unopened messages in the cell-phone are opened.
The already-read and unread short messages can be
respectively downloaded up to 75.
4 Display the text
Press the Control knob.
Turning the Control knob scrolls the message.
Pressing the Control knob again returns to the
message list screen.
5 Exit SMS Inbox mode
Press the [FNC] button.
⁄
•
•
•
The unopened message is displayed at the beginning
of the list. Other messages are displayed in the order of
reception.
The SMS that has arrived when the cell-phone is not
linked with Bluetooth cannot be displayed. Download
the SMS.
The short message cannot be displayed during
downloading the SMS.
|
36 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
TV control (Optional)
Basic Operation
Preset Tuning
Recalling the TV channels in the memory.
Selecting TV source
Press the [SRC] button.
Select the “TV” display.
For how to select source item, refer to <Power/
Source Select button> of <Basic Operation> (page
4).
1 Enter Preset Tuning Select mode
Press the [ ] button.
A list is displayed.
2 Select a desired station in the memory
Turn the Control knob.
Select the TV band and Video input
Push the Control knob toward up.
Each time you push the knob, TV bands and Video
input alternate.
3 Recall the station
Press the Control knob.
Cancelling Preset Tuning
Press the [ ] button.
Select the TV channel
Push the Control knob towards right or left.
Function of remote control
Preset Memory
Direct TV Tuning
Putting the TV channels in the memory.
Entering the TV channel and tuning.
1 Select the TV channel to put in the memory
1 Enter Direct TV Tuning mode
Press the [DIRECT] button on the remote
control.
Push the Control knob towards right or left.
2 Enter Preset Memory mode
“– –” is displayed.
Press the [ ] button.
2 Enter the TV channel
3 Select the number to put in the memory
Press the number buttons on the remote
Turn the Control knob.
control.
Example:
4 Determine the number to put in the memory
Press the Control knob for at least 2 second.
Desired channel
Press button
Cancelling the Preset Memory mode
Press the [ ] button.
8 ch
[0], [8]
Cancelling Direct TV Tuning
Press the [DIRECT] button on the remote
control.
English
|
37
Basic Operations of remote control
In Tuner source
SRC
ATT
VOL
AUD
SRC
AT T
Band select [FM]/[AM]
Station select [4]/[¢]
Recall preset stations [1] — [6]
VOL
AUD
FM/AM
2-ZONE
0 — 9
In CD/USB source
DIRECT
Music select [4]/[¢]
Folder/Disc select [FM]/[AM]
Pause/Play [38]
(page 13, 14, 15, 37)
In TV source
Band/Video input select [FM]
Channel select [4]/[¢]
Recall preset channels [1] — [6]
General control
Volume control [VOL]
Source select [SRC]
Volume reduce [ATT]
When the button is pressed again, the volume returns
to the previous level.
In Audio control
Audio item select [AUD]
Adjust the Audio item [VOL]
⁄
•
Refer to <Audio Control> (page 24) for the operation
method, such as the procedures for Audio control and
others operations.
Dual Zone control
Dual zone system on and off [2-ZONE]
Rear channel volume control [ 5]/ [∞]
|
38 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Loading and Replacing battery
Use two “AA”/ “R6”-size batteries.
Hands-free phone control
Slide the cover while pressing downwards to remove
it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
Making a call
Enter the dialing method selection mode
Select a dialing method [38]
Number dial input
[
]
Operation type
Input a digit.
Input“+”.
Input“#”.
Input“*”.
Operation
[0] – [9] buttons
[¢] button
[FM] button
[AM] button
[4] button
Clear the entered phone number.
Make a call [DIRECT]
Receiving a call
Answer the call
[
]
Switch between the private talk mode and the
hands-free talk mode [38]
Call waiting
Answer Another Incoming Call with the Current
Call Suspended
[
]
Answer another Incoming Call after Terminating
the Current Call [SRC]
Continue the Current Call [1]
During a call
End the call [SRC]
Adjust the voice volume [VOL]
¤ CAUTION
• Do not leave the battery near fire or under direct
sunlight. A fire, explosion or excessive heat
generation may result.
• Do not set the remote control in hot places such
as on the dashboard.
English
|
39
Appendix
About Audio file
iPod/iPhone that can be connected to this
•
•
•
•
Playable Audio file
unit
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device
USB mass storage class
Playable USB device file system
FAT16, FAT32
Made for
• iPod nano (1st generation)
• iPod nano (3rd generation)
• iPod with video
• iPod nano (2nd generation)
• iPod nano (4th generation)
• iPod classic
• iPod touch (1st generation) • iPod touch (2nd generation)
Works with
• iPhone
• iPhone 3G
•
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• Update iPod/iPhone software to the latest version.
• The word “iPod” appearing in this manual indicates
the iPod or the iPhone connected with the iPod
connection cable* (optional accessory).
* Not supported model KCA-iP500.
Refer to the web site for connectable iPod and iPod
connection cable.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
:
FFolldderr
Audiofile
CD
(ꢂ)
vꢀ
ꢁ
⁄
ꢃ
vꢆ
vꢇ
• If you start playback after connecting the iPod, the
music that has been played by the iPod is played
first.
ꢅ
vꢄ
ꢈ
In this case, “RESUMING” is displayed without
displaying a folder name, etc. Changing the browse
item will display a correct title, etc.
• You cannot operate iPod if “KENWOOD” or “✓”
displayed on iPod.
vꢉ
v.
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
About USB device
• When the USB device is connected to this unit,
it can be charged up provided that this unit is
powered.
⁄
•
In this manual, the word “USB device” is used for flash
memories and digital audio players which have USB
terminals.
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
• You cannot connect a USB device via a USB hub and
Multi Card Reader.
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• When connecting the USB device, usage of the
CA-U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
|
40 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
For operating KCA-BT200 (Optional)
For operation refer to Model-B-2 in the Instruction
Manual of KCA-BT200, and the table below.
About the Cell-Phone
This unit conforms to the following Bluetooth
specifications:
Version
Profile
Bluetooth Standard Ver. 1.2
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phonebook Access Profile)
SYNC (Synchronization Profile)
Notation used in the KCA-BT200 Operation
Instruction Manual
[38] button
Control knob
Press the Control knob for at least
1 second.
Press the [AUTO]/[TI] button.
For the cell-phones verified for compatibility, access
the following URL:
For operating KCA-BT100 (Optional)
The following control methods of the function
for this unit may be different from the Instruction
manual; therefore, refer to the following supplemental
instruction.
<Dialing by Using the Quick Dialing Function>
1. Press the Control knob. Select the display other
than “INITIAL”.
⁄
•
The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its type.
HFP is a profile used to make a hands-free call.
OPP is a profile used to transfer data such as a phone book
between units.
•
•
2. Press the [ ] button.
3. Select the number to recall by turning the Control
knob.
4. Press the Control knob.
About the Bluetooth Audio player
This unit conforms to the following Bluetooth
specifications:
<Registering to the Preset Dial Number List>
1. Operation is the same. Refer to the instruction
manual of KCA-BT100.
Version
Profile
Bluetooth Standard Ver. 1.2
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
2. Press the [ ] button.
3. Select the number to memory by turning the
Control knob.
4. Press the Control knob for at least 1 second.
⁄
<Deleting a Registered Cell-Phone>
Refer to <Deleting a Registered Bluetooth device>
in this instruction manual.
•
A2DP is a profile designed to transfer the music from an
audio player.
•
AVRCP is a profile designed to control playback and
selection of music by an audio player.
<Menu System>
For how to operate Menu, refer to <Function
Control> in this instruction manual.
About display
Cell-Phone Status is displayed in the status display of
this unit.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
About KENWOOD “Music Editor” of PC
application
• “Music Editor” is recorded in the CD-ROM attached
to this unit.
• Refer to the user’s manual recorded in the
installation CD-ROM and Help of “Music Editor” for
the operation method of “Music Editor”.
• The unit can play USB device created by “Music
Editor”.
Displays of KCA-BT100 Instruction Actual displays on this unit
Manual
“DISCONCT”
“CONNECT”
“PHN-DEL”
“P-STATUS”
“HF Disconnect”
“HF Connect”
“Device Delete”
“Phone Status”
• Information about “Music Editor” upgrade is put on
English
|
41
Appendix
•
DISP N/P
Menu Glossary
Switches the panel display between positive
or negative. In addition, you can reverse it in
conjunction with the interior light.
•
AMP
Selecting “OFF” turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
Auto Answer (Setting the Time Interval for
Automatic Answer)
POSI1 : Displays the text in the positive.
•
POSI2 : When the interior light is off, the text is
displayed in the positive; when the interior
light is on, the text is displayed in the
negative.
This function automatically answers (responds
to) a call after lapse of the preset time interval for
automatic answer.
“OFF” : Does not answer the phone call
automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call
after lapse of 1 – 99 seconds.
NEGA1 : Displays the text in the negative.
NEGA2 : When the interior light is off, the text
is displayed in the negative; when the
interior light is on, the text is displayed in
the positive.
•
DTA (Digital Time Alignment)
Make fine adjustment of the delay time of the
speaker output specified at <Cabin selection>
(page 25) to have a more suitable environment for
your vehicle.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
⁄
•
If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
•
This function does not work for call waiting.
•
•
Call Beep (Setting the Beep of the Incoming Call)
You can output a beep from the speaker when a
call comes in.
“ON” : Beep is heard.
“OFF” : Beep is canceled.
CD Read
Sets the method for reading CD.
When unable to play special format CD, set this
function to “2” to force playing. Note that some
music CD may be unplayable even when set to “2”.
In addition, audio files cannot be played when set
to “2”. Normally, keep this set to “1”.
3 Calculate the distance difference in accordance
with the farthest speaker.
1 : Automatically distinguishes between audio file
disc and music CD when playing disc.
2 : Forces playing as music CD.
+100cm
•
Chinese (Chinese language setting)
When this is set to ON, the following character
strings are displayed in Chinese:
Folder name/ File name/ Song title/ Artist name/
Album name/ KCA-BT200/BT100 (optional
accessory)
FRONT
FRONT
REAR
50cm
80cm
REAR
•
•
Display
If this unit is not operated at least 5 seconds with
“OFF” selected, the display turns off. During a setup
mode, the display will not turn off even if 5 seconds
lapse.
150cm
+70cm
+0cm
SUB-W
DISP DIM (Display illumination dimmer)
Reduces the display Illumination brightness.
AUTO: Dims the illumination in conjunction with
the Light switch of the vehicle.
MNAL1: Dims the illumination constantly.
MNAL2: Dims the illumination darker than MNA1.
OFF: Does not dim the illumination.
•
BT DVC Status (Displaying the Bluetooth device
Status)
You can display the connection status, signal
strength, and battery level.
: Battery level of cell-phone.
Full
Nearly dead
|
42 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
: Signal strength of cell-phone.
Maximum
•
Supreme+ (Supreme Plus)
Minimum
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding.
⁄
•
Icons are not displayed if information cannot be
obtained from the cell-phone.
Since the number of steps of the control unit is different
from that of the cell-phone, the statuses displayed on
the control unit may discord from those displayed on
the cell-phone.
The bass and vocal sound that are cut off by
encoding are supplemented for the reproduction
of natural sound quality.
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
The bass and vocal sound of Music CD and iPod is
also supplemented.
•
•
•
HIGHWAY-SOUND
Increases the volume of faintest sound being lost
by road noises to make the sound more audible.
Additionally, it accentuates bass sound being
lost by road noises to make the bass sound more
dynamic.
•
Zone2 (Dual Zone)
Illumi DIM (Key illumination dimmer)
Reduces the key Illumination brightness.
AUTO: Dims the illumination in conjunction with
the Light switch of the vehicle.
Set the destination (front speaker “Front” or rear
speaker “Rear”) of the sub source (AUX IN) when the
Dual Zone function is turned on.
MNAL1: Dims the illumination constantly.
MNAL2: Dims the illumination darker than MNA1.
OFF: Does not dim the illumination.
The marking of products using lasers
(Except for some areas)
•
Language (Language setting)
When the language is selected, the following
character strings are displayed in the selected
language:
CLASS 1
LASER PRODUCT
Folder name/ File name/ Song title/ Artist name/
Album name/ KCA-BT200/BT100 (optional
accessory)
The label is attached to the chassis/case and says
that the component uses laser beams that have been
classified as Class 1. It means that the unit is utilizing
laser beams that are of a weaker class. There is no
danger of hazardous radiation outside the unit.
•
•
Mic Gain
Adjusts the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to “+” increases the voice volume.
•
•
The “AAC” logo is trademark of Dolby Laboratories.
NR Level
Reduces the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to “+” increases the
noise reduction.
The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by Kenwood Corporation is under license. Other
trademarks and trade names are those of their
respective owners.
•
•
iTunes is a trademark of Apple Inc.
•
SP Select (Setting up the Voice Output
Speakers)
You can specify the voice output speakers.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
“FRONT” : Outputs voice from the front-left and
front-right speakers.
“F-R” : Outputs voice from the front-right speaker.
“F-L” : Outputs voice from the front-left speaker.
•
•
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
⁄
•
•
“Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to iPhone and has been certified by the developer to
meet Apple performance standards.
•
Select the speaker which is further from the microphone
in order to prevent howling or echoes.
•
SRC Select
Setting up the Source Select mode.
1 : Displays source icons for your choice.
2 : Allows you to select sources one after another.
Apple is not responsible for the operation of this
device or its compliance with safety and regulatory
standards.
English
|
43
Accessories/ Installation Procedure
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
Reception may drop if there are metal objects near the
Bluetooth antenna.
Accessories
1
2
3
4
•
•
..........1
..........2
..........4
..........4
5*
•
•
3 m ..........1
*Accessory of
KDC-XBT8013U/
KDC-XBT8013UL
•
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
•
•
•
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
Bluetooth antenna unit
2WARNING
About CD players/disc changers connected
to this unit
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
If the CD player/ disc changer has the “O-N” switch, set
it to the “N” position.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
¤
•
Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
For Good Reception
To assure good reception, note the following:
•
•
Make sure to ground the unit to a negative 12V DC power
supply.
• Communicate with the cell-phone within the line-
of-sight distance of 10 m (30 ft). The communication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
above maximum communication range (10 m) is
not always assured.
Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
If the power is not turned ON (“Protect” is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
•
•
• A broadcast station or walkie-talkie located nearby
can interfere with communication due to too strong
signal.
|
44 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Connecting Wires to Terminals
To USB device
USB connector (1m)
Steering remote control
Do not remove the cap when you do
not use the USB cable. The connector
will cause the unit to malfunction if it
gets in touch with any metallic part of
the vehicle.
(Light Blue/Yellow)
Rear output
⁄
R
L
Front output
REMO.CONT
Sub Woofer output
To use the steering
⁄
wheel remote control
feature, you need to
an exclusive remote
adapter (not supplied)
matches your car is
required.
Microphone input
(KDC-XBT8013U/
KDC-XBT8013UL only)
Microphone
(Accessory5)
FM/AM antenna input
R
L
AUX input (Stereo)
Use the mini-plug which is stereo type
and does not have any resistance.
Fuse (10A)
Wiring harness
(Accessory1)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant
⁄
instruction manuals.
White
White/Black
To front left speaker
Gray
Gray/Black
To front right speaker
To rear left speaker
To rear right speaker
Green
Green/Black
Purple
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Power control wire (Blue/White)
Motor antenna control wire (Blue)
When using the optional power amplifier, connect to its power control
terminal.
P.CONT
Depending on what antenna you are using, connect either to the control
terminal of the motor antenna, or to the power terminal for the booster
amplifier of the film-type or short pole type antenna.
ANT.
CONT
TEL mute wire (Brown)
Connect to the terminal that is grounded when either the telephone
rings or during conversation.
MUTE
To connect the Kenwood navigation system, consult your
⁄
navigation manual.
Dimmer control wire (Orange / White)
To car light control switch
ILLUMI
Car fuse
box
Ignition key
switch
Ignition wire (Red)
ACC
Car fuse box
(Main fuse)
Battery wire (Yellow)
Ground wire (Black) · (To car chassis)
+
–
Battery
English
|
45
Installation/Removing the Unit
non-Japanese cars
Removing the hard rubber frame
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
Lock
Catch
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Accessory2
⁄
Removal tool
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
2 When the upper level is removed, remove the
lower two locations.
⁄
Japanese cars
•
The frame can be removed from the bottom side in the
same manner.
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
Removing the Unit
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Insert the two removal tools deeply into the slots
T
N
on each side, as shown.
T/N
3 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
T
N
T: Toyota cars
N: Nissan cars
Accessory2
8 mm
MAX.
8mm
MAX.
3
4
ø5mm
ø5mm
Accessory3...for Nissan car
Accessory4...for Toyota car
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
4 Pull the unit all the way out with your hands, being
¤ CAUTION
careful not to drop it.
Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as
the heat sink and enclosure become hot.
|
46 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Accessory of KDC-XBT8013U/ KDC-XBT8013UL
Installation the Microphone Unit
1 Check the installation position of the microphone
(accessory 5).
2 Remove oil and other dirt from the installation
surface.
3 Install the microphone.
4 Wire the microphone cable up to the hands-free
box with it secured at several positions using tape
or the like.
Accessory5
Fix a cable with a commercial
item of tape.
Peel the release coated paper of double-face adhesive tape to
fix on the place shown above.
Adjust the direction of the microphone to the driver.
⁄
•
Install the microphone as far as possible from the cell-
phone.
English
|
47
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
• Cannot set up the subwoofer.
• No output from the subwoofer.
• Cannot set up the subwoofer position of Manual
position setting.
General
? The Touch Sensor Tone does not sound.
• <Subwoofer output> of <Basic Operation> (page 4)
is not set to On.
• The Dual zone function is enabled. ☞ <Audio
✔
The preout jack is being used.
☞
The Touch Sensor Tone cannot be output from
the preout jack.
Setup> (page 27)
? The illumination flashes when the knob or button
is operated.
!
!
• Cannot set up the subwoofer phase.
The Low Pass Filter is set to Through. ☞ <X’Over
setting> (page 29)
✔
This is the key illumination effect.
☞
You set this effect in “MENU” > “ILM Effect” of
<Function Control> (page 6).
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 27)
? The key illumination effect brought about in
conjunction with the sound volume is small.
✔
The key illumination effect may be insufficient
depending on the sound volume and sound
quality.
!
• Cannot register a security code.
• Cannot set up Display.
Tuner source
<Demonstration mode Setting> (page 26) is not
turned off.
? Radio reception is poor.
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
Disc source
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
☞
Clean the CD, referring to the CD cleaning of the
section on <Handling CDs> (page 3).
The disc is loaded in a different slot from that
specified.
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
Audio file source
? The sound skips when an Audio file is being
played.
✔
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 3).
The recording condition is bad.
Record the media again or use another media.
☞
|
48 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Hands-free
The messages shown below display your
systems condition.
? The hands-free talk volume is low.
✔
The hands-free talk volume is set at a low level.
TOC Error:
• No disc has been loaded in the disc
magazine.
☞
The hands-free talk volume can be adjusted
independently. Adjust it during hands-free talk.
“MENU” > “Mic Gain” and “NR Level” <Function
Control> (page6).
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
ERROR 05:
ERROR 77:
The disc is unreadable.
? No sound is heard from the rear speakers.
You are talking in the hand-free talk mode.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
“ERROR 77” code does not disappear,
consult your nearest service center.
✔
☞
No sound is heard from the rear speakers in the
hands-free talk mode.
? No beep is heard at reception of an incoming call.
ERROR 99:
Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the “ERROR
99” code does not disappear, consult your
nearest service center.
✔
No beep is heard depending on the type of your
cell-phone.
☞
The “MENU” > “Call Beep” of <Function Control>
(page 6) is set ON.
? Voice is not recognized.
✔
✔
✔
The vehicle window is open.
CD-IN (Blink): The CD player section is not operating
properly.
☞
If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows
to reduce noise.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
Small voice.
If voice is too small, it cannot be recognized
☞
properly. Speak into the microphone a little more
loudly and naturally.
The person uttering the voice tag is not the one who
registered the it.
Protect (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable properly
and press the reset button. If the “Protect”
code does not disappear, consult your
nearest service center.
☞
Only the voice of the person who registered the
voice tag can be recognized.
Bluetooth audio source
? The Bluetooth audio player cannot be registered
(pairing).
Unsupported File:
✔
The PIN code is fixed.
An Audio file is played with a format that this
unit can’t support.
☞
When a PIN code is specified in the Instruction
Manual for Bluetooth Audio Player, register it
with reference to <Registering PIN Code> (Page
32) to register the Bluetooth audio player. If no
PIN code is specified in the Instruction Manual,
try “0000”.
Copy Protection:
A copy-protected file is played.
Read Error:
The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
? The sound from the Bluetooth audio player is
discontinuous.
✔
The distance between this unit and audio player is
too far.
☞
Move the audio player nearer to this unit.
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
✔
Another Bluetooth device is affecting the Bluetooth
communication.
☞
☞
Turn off another Bluetooth device.
Move another Bluetooth device away from this
unit.
✔
Another Bluetooth device or profile is used for
communication.
☞
• An unsupported USB device is connected.
• Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(Page 40) for information on supported
iPods.
The downloading of the Phone book or the SMS
disconnects the sound.
English
|
49
Troubleshooting Guide
No Music Data/Error 15:
Too Long:
The word or utterance is too long to be
recognized.
• The connected USB device contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
No Phonebook: Data is not contained in the phone book.
No Message: No short message in In Box.
USB ERROR:
iPod Error:
Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
No Record:
The voice tag is not registered in the
phonebook.
Memory Full: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
Favorite: No Memory:
The procedure is not registered to Favorite
Preset Memory
No Access:
No Voice:
The procedure preset with Favorite Control
cannot be available. The preset content may
not be recalled depending on the selected
source or mode.
USB REMOVE (Blink):
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
No call.
NO Number: • The calling party does not notify a caller ID.
• There is no phone number data.
No Data:
• There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
No Entry:
The cell-phone has not been registered
(pairing).
HF Disconnect: The unit cannot communicate with the cell-
phone.
HF Error 07:
The memory cannot be accessed.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF Error 68:
The unit cannot communicate with the cell-
phone.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
Un Known:
Device Full:
The Bluetooth device cannot be detected.
5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN Code NG: The PIN code is wrong.
Connect NG: The unit cannot be connected to the device.
Pairing Failed: Pairing error.
Err No Matching:
The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
Too Soft:
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
Too Loud:
|
50 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
Specifications
FM tuner section
CD player section
Frequency range
200 kHz space : 87.9 MHz – 107.9 MHz
Laser diode
: GaAlAs
50 kHz space : 87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 70 dB
Selectivity ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 40 dB
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 24 Bit
Spindle speed
: 500 – 200 rpm (CLV)
Wow & Flutter
: Below Measurable Limit
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Total harmonic distortion (1 kHz)
: 0.008 %
Signal to Noise ratio (1 kHz)
: 110 dB
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AM tuner section
Frequency range
10 kHz space : 530 kHz – 1700 kHz
9 kHz space : 531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
AAC decode
: AAC-LC “.m4a” files
Bluetooth section
(KDC-XBT8013U/ KDC-XBT8013UL)
Version
: Bluetooth Ver. 1.2 Certified
Frequency range
: 2.402 – 2.480 GHz
Output Power
: +4dBm (MAX), 0dBm (AVE) Power Class 2
Maximum Communication range
: Line of sight approx.10m (32.8 ft)
Profiles
: HFP (Hands Free Profile)
: HSP (Headset Profile)
: SPP (Serial Port Profile)
USB Interface
USB Standard
: USB1.1/ 2.0 (Full speed)
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC “.m4a” files
: PBAP (Phonebook Access Profile)
: OPP (Object Push Profile)
: SYNC (Synchronization Profile)
: A2DP (Advanced Audio Distribution Profile)
: AVRCP (Audio/Video Remote Control Profile)
English
|
51
Specifications
Audio section
Maximum output power
: 50 W x 4
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
Tone action
BAND1 (60 Hz): 9 dB
BAND2 (250 Hz): 9 dB
BAND3 (1 kHz): 9 dB
BAND4 (4 kHz): 9 dB
BAND5 (16 kHz): 9 dB
Preout level / Load (CD)
: 4000 mV/10 kΩ
Preout impedance
: ≤ 600 Ω
Auxiliary input
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 10 kΩ
General
Operating voltage
KDC-XBT8013U/KDC-XBT8013UL
(10.5 – 16V allowable) : 14.4 V
KDC-X7013U/KDC-X7013UL
(11 – 16V allowable) : 14.4 V
Maximum Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
Weight
: 1.4 kg
Specifications subject to change without notice.
|
52 KDC-XBT8013U/ KDC-XBT8013UL/ KDC-X7013U/ KDC-X7013UL
|