The guidelines are based on standards that were
developed by independent scientific organizations
through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety
margin designed to assure the safety of all persons,
regardless of age and health.
The FCC has granted an Equipment Authorization for this
model phone with all reported SAR levels evaluated as in
compliance with the FCC RF emission guidelines. SAR
information on this model phone is on file with the FCC
and can be found under the Display Grant section at
http://www.fcc.gov/oet/fccid after searching on the
FCC ID: OVFKWC-S6000-150.
The exposure standard for wireless mobile phones
employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC is
1.6 W/kg.* Tests for SAR are conducted using standard
operating positions specified by the FCC with the phone
transmitting at its highest certified power level in all tested
frequency bands.
Additional information on SAR can be found on the
Cellular Telecommunications and Internet Association
* In the United States and Canada, the SAR limit for
mobile phones used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. The standard
incorporates a substantial margin of safety to give
additional protection for the public and to account for any
variations in measurements.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the phone while
operating can be well below the maximum value.
This is because the phone is designed to operate at
multiple power levels so as to use only the power required
to reach the network. In general, the closer you are to a
wireless base station antenna, the lower the
power output.
Caution
The user is cautioned that changes or modifications not
expressly approved by the party responsible for
compliance could void the warranty and user’s authority
to operate the equipment.
Before a phone model is available for sale to the public,
it must be tested and certified to the FCC that it does not
exceed the limit established by the government-adopted
requirement for safe exposure. The tests are performed
in positions and locations (e.g., at the ear and worn on
the body) as required by the FCC for each model.
Optimize your phone’s performance
Use the guidelines on page 2 to learn how to optimize the
performance and life of your phone and battery.
Air bags
If you have an air bag, DO NOT place installed or
portable phone equipment or other objects over the air
bag or in the air bag deployment area. If equipment is not
properly installed, you and your passengers risk
serious injury.
Body-worn measurements differ among phone models,
depending upon availability of accessories and FCC
requirements. While there may be differences between
the SAR levels of various phones and at various
positions, they all meet the government requirement for
safe exposure.
User Guide for the Kyocera K126C Phone
iii
Vehicles—RF signals may affect improperly installed
or inadequately shielded electronic systems in
motor vehicles. Check with the manufacturer of the
device to determine if it is adequately shielded from
external RF energy.
Medical devices
Pacemakers—Warning to pacemaker wearers: Wireless
phones, when in the ‘on’ position, have been shown
to interfere with pacemakers. The phone should be
kept at least six (6) inches away from the pacemaker
to reduce risk.
Blasting areas—Turn off your phone where blasting is in
progress. Observe restrictions, and follow any
regulations or rules.
The Health Industry Manufacturers Association and the
wireless technology research community recommend
that you follow these guidelines to minimize the potential
for interference.
Potentially explosive atmospheres—Turn off your phone when
you are in any area with a potentially explosive
atmosphere. Obey all signs and instructions. Sparks in
such areas could cause an explosion or fire, resulting in
bodily injury or death.
•
Always keep the phone at least six inches
(15 centimeters) away from your pacemaker when
the phone is turned on.
•
•
•
Do not carry your phone near your heart.
Use the ear opposite the pacemaker.
If you have any reason to suspect that interference is
taking place, turn off your phone immediately.
Areas with a potentially explosive atmosphere are often,
but not always, clearly marked.
They include:
•
•
•
•
fueling areas such as gas stations
below deck on boats
transfer or storage facilities for fuel or chemicals
vehicles using liquefied petroleum gas, such as
propane or butane
Hearing aids—Some digital wireless phones may interfere
with hearing aids. In the event of such interference, you
may want to consult your service provider or call the
customer service line to discuss alternatives.
•
•
areas where the air contains chemicals or particles
such as grain, dust, or metal powders
any other area where you would normally be advised
to turn off your vehicle engine
Other medical devices—If you use any other personal medical
device, consult the manufacturer of the device to
determine if it is adequately shielded from external RF
energy. Your physician may be able to help you obtain
this information.
Use with care
Use only in normal position (to ear). Avoid dropping,
hitting, bending, or sitting on the phone.
In health care facilities—Turn your phone off in health care
facilities when instructed. Hospitals and health care
facilities may be using equipment that is sensitive to
external RF energy.
Keep phone dry
If the phone gets wet, turn the power off immediately and
contact your dealer. Water damage may not be covered
under warranty.
Potentially unsafe areas
Posted facilities—Turn your phone off in any facility when
posted notices require you to do so.
iv
The wireless telephone industry has developed ratings
for some of their mobile phones to assist hearing device
users in finding phones that may be compatible with their
hearing devices. Not all phones have been rated.
Resetting the phone
If the screen seems frozen and the keypad does not
respond to keypresses, reset the phone by completing
the following steps:
Phones that are rated have the rating on their box or a
label on the box. The ratings are not guarantees, and
results will vary depending on the user’s hearing device
and hearing loss. If your hearing device happens to be
vulnerable to interference, you may not be able to use a
rated phone successfully. Trying out the phone with your
hearing device is the best way to evaluate it for your
personal needs.
1
2
Remove the battery door.
Remove and reinstall the battery
(see “Installing the battery” on page 1).
If the problem persists, return the phone to the dealer
for service.
Accessories
Use only Kyocera-approved accessories with Kyocera
phones. Use of any unauthorized accessories may be
dangerous and will invalidate the phone warranty if said
accessories cause damage or a defect to the phone.
M-Ratings— Phones rated M3 or M4 meet FCC
requirements and are likely to generate less interference
to hearing devices than phones that are not labeled. M4
is the better/higher of the two ratings.
To shop online for phone accessories, visit
T-Ratings— Phones rated T3 or T4 meet FCC requirements
and are likely to be more usable with a hearing device’s
telecoil (“T Switch” or “Telephone Switch”) than unrated
phones. T4 is the better/higher of the two ratings. (Note
that not all hearing devices have telecoils in them.)
To order by phone, call 800-349-4188 (U.S.A. only) or
858-882-1410.
Radio Frequency (RF) energy
Your telephone is a radio transmitter and receiver. When
it is on, it receives and sends out RF energy. Your service
provider’s network controls the power of the RF signal.
This power level can range from 0.006 to 0.6 watts.
Hearing devices may also be measured for immunity to
this type of interference. Your hearing device
manufacturer or hearing health professional may help
you choose the proper rating for your mobile phone. The
more immune your hearing aid is, the less likely you are
to experience interference noise from mobile phones.
Hearing Aid Compatibility (HAC) with Mobile Phones
Some mobile phones and hearing devices (hearing aids
and cochlear implants), when used together, result in
buzzing, humming, or whining noises detected by the
user. Some hearing devices are more immune than
others to this interference noise, and phones also vary in
the amount of interference they generate.
For more information about hearing aid compatibility, visit
the FCC's Consumer & Governmental Affairs Bureau
User Guide for the Kyocera K126C Phone
v
Battery and charger specifications
Charger
Input
Output
CE90-R2233-01
Standard Battery:
100-240VAC 50/60Hz 5VDC 350mA
CV90-N3344, 3.7 V / 900 mAh
Kyocera Wireless Corp.
10300 Campus Point Drive, San Diego, CA 92121 U.S.A.
Visit us at www.kyocera-wireless.com
To purchase accessories, visit
vi
CONTENTS
Editing a phone number . . . . . . . . . . . . . . . . . . . . . . . 17
Finding contact information . . . . . . . . . . . . . . . . . . . . 18
1
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Caring for the battery . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Understanding screen icons . . . . . . . . . . . . . . . . . . . . . 2
Getting to know your phone . . . . . . . . . . . . . . . . . . . . . 4
Using menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Performing basic functions . . . . . . . . . . . . . . . . . . . . . . 6
5
6
Sending and Receiving
Text Messages . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sending text messages . . . . . . . . . . . . . . . . . . . . . . . . . 20
Retrieving text messages . . . . . . . . . . . . . . . . . . . . . . . 23
Erasing messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Customizing message settings . . . . . . . . . . . . . . . . . . . 25
2
Making and Answering Calls . . . . . . . . . . . . . . . 7
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Answering calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using the speakerphone . . . . . . . . . . . . . . . . . . . . . . . . 8
Dealing with missed calls . . . . . . . . . . . . . . . . . . . . . . . 8
Viewing recent calls . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Speed dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1-Touch dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting up voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Silencing an incoming call . . . . . . . . . . . . . . . . . . . . . 11
Calling emergency services . . . . . . . . . . . . . . . . . . . . . 11
Tracking calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Timing your calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Locking the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Customizing Your Phone . . . . . . . . . . . . . . . . . 26
Silencing all sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Choosing ringers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Adjusting volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting message alerts . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Personalizing the screen . . . . . . . . . . . . . . . . . . . . . . . 30
Creating a secure environment . . . . . . . . . . . . . . . . . . 31
Network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Accessory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Factory reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7
Tools & Games . . . . . . . . . . . . . . . . . . . . . . . . . 35
Brick Attack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
My Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
My Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Alarm Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Tip Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Calculator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
World Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3
4
Entering Text, Numbers,
and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Understanding text entry screens . . . . . . . . . . . . . . . . 13
Capitalization settings . . . . . . . . . . . . . . . . . . . . . . . . . 14
Quick reference to text entry . . . . . . . . . . . . . . . . . . . 15
Storing Contacts. . . . . . . . . . . . . . . . . . . . . . . . 16
Creating a new contact . . . . . . . . . . . . . . . . . . . . . . . . 16
Editing or erasing a contact . . . . . . . . . . . . . . . . . . . . 17
User Guide for the Kyocera K126C Phone
vii
8
9
Using Voice Recognition . . . . . . . . . . . . . . . . 40
Setting up voice dialing . . . . . . . . . . . . . . . . . . . . . . . .40
Making a call using voice tags . . . . . . . . . . . . . . . . . . .41
Making a call using digit dialing . . . . . . . . . . . . . . . . . .41
Using voice features . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Training voice recognition . . . . . . . . . . . . . . . . . . . . . .43
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Customer support . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
10 Consumer Limited Warranty. . . . . . . . . . . . . . 45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
viii
1
GETTING STARTED
Installing the battery
Your phone comes with a removable lithium ion
(LiIon) battery.
Charging the battery
You must have at least a partial
charge in the battery to make or
receive calls. Fully charge the
battery before using the phone.
1. Hold the phone with the back
facing you.
To charge the battery, connect the
AC adapter to the jack on the
bottom of the phone, then plug the
adapter into a wall outlet.
2. Unsnap the battery door by
sliding your fingernail into the
recess located at the bottom of
the battery door.
The battery icon in the upper-right corner of the screen
tells you whether the phone is:
3. Place the battery in the phone
casing with the metal contacts
toward the bottom of the
phone.
•
•
•
Charging (the icon is animated)
Partially charged
Fully charged
4. Place the tab at the top of the
battery door in the opening at
the top of the battery well.
Recharging the battery
You can safely recharge the battery at any time, even if it
has a partial charge.
5. Press the battery door until it
snaps into place.
User Guide for the Kyocera K126C Phone
1
Caring for the battery
Understanding screen icons
These icons may appear on your phone’s home screen.
General safety guidelines
•
•
•
•
Do not take apart, puncture, or short-circuit
the battery.
If you have not used the battery for more than a
month, recharge it before using your phone.
Avoid exposing the battery to extreme temperatures,
direct sunlight, or high humidity.
The phone is operating in IS 2000 (1X)
digital mode.
The phone is receiving a signal. You can
make and receive calls. Fewer bars indicate
a weaker signal.
Never dispose of any battery in or near a
fire – it could explode.
A call is in progress.
The phone is not receiving a signal. You cannot
make or receive calls.
Common causes of battery drain
•
•
•
Playing games.
Keeping backlighting on.
Operating in digital mode when far away from a base
station or a cell site.
The alarm clock is set.
The phone is in privacy mode.
•
•
Using the headset.
You have a text message.
Operating when no service is available, or when
service is available intermittently.
High earpiece and ringer volume settings.
Repeating sound, vibration, or lighted alerts.
Long conversation.
You have a new voice message.
•
•
•
•
The battery is fully charged. The more black
bars, the greater the charge.
Operating in speakerphone mode.
Keyguard is on. The keypad is locked.
2
Getting Started
The phone is set to light up instead of ring.
The phone is set to vibrate or to vibrate and then
ring.
Position location is set to carrier and to
emergency services.
Position location is set to emergency
services only.
Phone is set to Auto Answer.
Speakerphone is on.
RM
Phone is in roaming mode.
User Guide for the Kyocera K126C Phone
3
Getting to know your phone
Home screen.
1
2
3
4
5
OK key selects a menu item or option.
Send/Talk key starts or answers calls.
Keypad for entering numbers, letters, or symbols.
* Shift key changes the text mode in text entry and also activates
the keypad lock.
Back key accesses menu options, erases characters in text entry,
returns to previous screen.
6
7
8
Navigation key positions cursor during text entry. Scrolls through
menu lists.
End/Power key turns the phone on and off, ends a call, returns
to home screen.
# Space key enters a space during text entry.
9
0 Next key cycles through word choices during text entry and is also
10
used for “+” dialing.
Jack for hands-free headset (sold separately)*
11
12
Jack for AC adapter (included)*.
*Warning: Inserting an accessory into the incorrect jack will damage the phone.
4
Getting Started
Using menus
The contents of the main menu are as follows:
Prepaid
Messages (cont’d)
Contacts
Settings
Tools/Games
Brick Attack
My Sounds
My Graphics
Scheduler
Alarm Clock
Tip Calculator
Calculator
Add Airtime
Saved
Drafts
Msg Settings
Group Lists
Erase Msgs
View All
Add New
Find Name
Add Voice Dial
Speed Dial List
Voice Dial List
Business List
Personal List
Information
Silent Mode
Keyguard
Sounds
Display
Voice Services
Security
Buy Airtime*
My Phone Number
Airtime Info
Airtime Display
Serial Number
Code Entry Mode
Recent Calls
All Calls
Incoming Calls
Outgoing Calls
Missed Calls
Erase Lists
Call Information
Network
World Clock
Timer
Stopwatch
Messages
New Text Msg
Voicemail
Inbox
Convenience
Msg Settings
Accessories
Phone Info
Factory Reset
Outbox
*This option may not be available. Check with your service provider for details.
Accessing menu items
•
•
Press
Press
and options*.
to select Menu.
left, right, up, or down to view menus
In this guide, an arrow → tells you to select an option
from a menu. For example, Menu → Settings means
select Menu, then select the Settings option.
•
•
•
Press
Press
Press
to select a menu item.
to back up a menu level.
to return to the home screen.
* To change the way the menus appear, select Menu →
Settings → Display → Main Menu View, then select
Graphic, or List and press
. See “Choosing a menu
view” on page 30 for details.
User Guide for the Kyocera K126C Phone
5
Performing basic functions
To...
From the home screen...
Turn the phone on
Press
and wait until the phone chimes.
Turn the phone off
Make a call
Press and hold
until the phone beeps.
Enter the number, and press
.
End a call
Press
Press
.
Answer a call
.
Access voicemail
Verify your phone number
Press and hold
and follow the system prompts.
Select Menu → Settings → Phone Info → Build Info and
scroll down to Your Number.
Silence the ringer on an incoming call
Press
-or-
, then
to answer.
Press
up or down, then
to answer.
Silence all sounds
Press and hold
Press and hold
Press and hold
Press and hold
Press and hold
.
Access contacts list
Access ringer volume
Access the Messages menu
Send a text message
down.
right.
left.
up.
6
Getting Started
2
MAKING AND ANSWERING CALLS
Note: If the contact has more than one phone number
assigned to it, press to select the contact’s name,
highlight the phone number you want to call, and
press
Making a call
1. Make sure you are in an area where a signal can be
received. Look for
on the home screen.
.
Note: The more bars you see in this symbol, the
stronger the signal. If there are no bars, move to
where the signal strength is better.
Answering calls
When a call comes in, the phone rings and
2. Enter the phone number.
“
Incoming Call” appears on the screen. The phone
3. Press
.
number of the caller also appears if it is not restricted. If
the number is stored in your Contacts directory, the
4. Press
to end the call.
contact name appears. To answer the call, press
.
Redialing a number
To silence or ignore the call
To redial the last number called, received, or missed,
press
three times.
When an incoming call is received, you can choose to
do one of the following:
Calling a saved number
•
•
•
•
Press
Press
Press
down to silence the ringer.
to silence the ringer.
If you have already saved a phone number, you can use
the Contacts list to find it quickly.
. Then press
to answer the call.
1. Press
down to view all Contacts.
Select Ignore Call to immediately send the caller to
voicemail. “Missed Calls” appears on your screen.
Note that in the absence of voicemail, this feature
drops the call.
2. Scroll down the list to find the contact you want
to call.
3. Highlight the name and press
to dial
the number.
User Guide for the Kyocera K126C Phone
7
Adjusting the volume during a call
•
Viewing recent calls
To adjust the earpiece volume during a call, press
up or down.
Details on the last calls you made, received, and missed
(10 each, 30 total) are stored in the Recent Calls list
and are identified by the following icons:
Using the speakerphone
Note: The speakerphone can only be activated during
Outgoing call
Incoming call
a call.
Missed call
(flashing)
•
•
To activate the speakerphone during a call, press
right once and then press
to
Recent call details
select
On.
To deactivate the speakerphone during a call,
select Off.
1. To view details of recent calls, select Menu →
Recent Calls.
2. Select from All Calls, Incoming Calls,
Dealing with missed calls
When you have missed a call, “Missed Calls” appears on
your screen.
Outgoing Calls, or Missed Calls.
3. Select a recent call and press
. Select from
the following:
•
•
To clear the screen, press
To return the call, highlight Missed Calls, press
then press
.
–
–
–
Time displays the time the call was made,
received, or missed and its duration.
Number displays the phone number of
the call.
Send Msg allows you to send a text message to
the phone number.
.
Setting missed call alerts
You can set an alert to beep every five minutes after you
have missed a call.
•
Select Menu → Settings → Sounds →
Missed Call → Enabled.
8
Making and Answering Calls
–
–
Prepend allows you to add an area code to the
number if you plan to save the number as
a contact.
Save New adds the phone number to the
Contacts list.
Erasing recent calls
1. Select Menu → Recent Calls → Erase Lists.
2. Select an option: Incoming Calls, Outgoing Calls,
Missed Calls or Erase All.
3. Press
right and press
to select Yes.
-or-
View Contact allows you to view the contact
information to make changes, if necessary.
Add to adds the phone number to a
saved contact.
Speed dialing
Speed dialing allows you to quickly dial a stored phone
number by entering a one- or two-digit speed dialing
–
–
location number and pressing
.
Erase deletes the call from the list of recent calls.
Note: Before you can use speed dialing, you must save a
phone number as a contact and assign a speed dial
location to it.
Note: If the phone number has been classified as
“secret,” you must enter your four-digit lock code to
view or edit it. For information on the lock code,
see “Changing your lock code” on page 31. To classify a
phone number as secret, see “Creating a new contact”
on page 16.
Refer to “Creating a new contact” on page 16 to create a
new contact, or “Editing or erasing a contact” on
page 17 to add speed dial to an existing contact.
Using speed dialing
Calling recent calls
To call a contact that has a speed dial location:
1. Select Menu → Recent Calls.
•
From the home screen, enter the one- or two-digit
speed dialing location and press
2. Select a list: All Calls, Incoming Calls, Outgoing
.
Calls, or Missed Calls.
3. Highlight the number you want to call.
4. Press
.
User Guide for the Kyocera K126C Phone
9
1-Touch dialing
1-Touch dialing is the fastest way to speed dial a contact
that has a speed dial location.
Setting up voicemail
Before your phone can receive voicemail messages, you
must set up a password and record a personal greeting
with your service provider. When you have set up your
voicemail, all unanswered calls to your phone are
automatically transferred to voicemail, even if your
phone is in use or turned off.
Note: You must (1) enable 1-Touch dialing on your
phone and (2) have a speed dial location assigned to
a contact.
Enabling 1-Touch dialing
1. From the home screen, press and hold
2. Press at the message.
.
1. Select Menu → Settings → Convenience →
1-Touch Dialing → Enabled.
3. Follow the system prompts to create a password and
record a greeting.
2. Press
.
Note: If you are having trouble accessing your
voicemail, contact your service provider.
Using 1-Touch dialing
To call a contact that has a speed dial location:
Checking voicemail messages
•
From the home screen, press and hold the speed
dialing number. If it is a two-digit number, press the
first digit briefly, then press and hold the second
digit. For example, if the speed dialing location is
When a voice message is received, your screen displays
“1 New Voicemail(s)” along with the
top of your screen.
symbol at the
15, press
briefly, then press and hold
.
If you see “1 New Voicemail(s)”
1. Press
your voicemail number.
2. Follow the prompts to retrieve the message.
to select Call, which initiates a call to
10
Making and Answering Calls
To clear the screen without checking messages:
Press right and press to select Ignore.
To exit Emergency mode
•
When you have completed the emergency call:
If you see only the symbol
1. Press
to select Exit.
1. Select Menu → Messages.
2. Press
again to confirm your choice.
2. Select Voicemail (1) to connect to your voicemail.
Tracking calls
You can track the number and duration of calls made
and received on your phone.
3. Follow the prompts to retrieve the message.
•
You can set the phone to beep or vibrate every five
minutes to remind you that you have voicemail. See
“Setting message alerts” on page 29.
1. Select Menu → Settings → Call Information →
Call Timers.
Silencing an incoming call
To silence an incoming call quickly, press
2. Select a timer:
•
or
–
Recent Calls Timer—Tracks all calls you have
made and received since you last reset this timer.
To reset this timer to zero, select Reset and
press
up or down. Then press
to answer
the call.
press
.
This action silences the current call only. The next call
will ring as normal.
–
Dialed Calls Timer—Tracks all outgoing calls
you have made since you last reset this timer. To
reset this timer to zero, select Reset and
Calling emergency services
•
press
.
Dial the 3-digit emergency code (911) and
press
.
You can call the code even if your phone is locked or
your account is restricted. When you call, your phone
enters Emergency mode. To make or receive regular
calls after dialing the code, you must exit this mode.
User Guide for the Kyocera K126C Phone
11
3. Press
to return to the Call Information menu to
Changing the keyguard setting
select one of the following:
1. Select Menu → Settings → Keyguard.
–
All Calls Timer—Tracks all calls you have made
and received. This timer cannot be reset.
Reset All Timers—Resets timers for recent and
dialed calls.
2. Highlight an option. You can set the phone to lock
the keypad immediately, or automatically if no key is
pressed after 30 seconds, 1 minute, or 5 minutes.
–
3. Press
to save.
Timing your calls
You can set your phone to beep 10 seconds before each
minute passes when you are on a call.
•
Select Menu → Settings → Sounds →
Minute Alert → Enabled.
Locking the keypad
The Keyguard locks your keypad to prevent accidental
key presses when the phone is turned on and a call is
not in progress. You can still answer or silence an
incoming call.
•
To lock the keypad from the home screen, press and
hold
To unlock the keypad, press
.
•
and then
.
12
Making and Answering Calls
3
ENTERING TEXT, NUMBERS, AND SYMBOLS
You can enter letters, numbers, and symbols in
Contacts, text messages, and your banner.
Entering numbers
To enter a number while in
number key once.
To enter a number while in
press and hold a number key until the number
appears on the screen.
•
•
mode, press a
or mode,
Understanding text entry screens
The current text entry mode (and capitalization setting,
when applicable) are indicated by icons.
Entering words letter by letter
text entry
field
Use normal alpha to enter letters.
text entry
mode
1. Press a key once for the first letter, twice for the
second letter, and so on. If your phone is set to
Spanish, accented letters are available.
2. Wait for the cursor to move right and enter the
Text entry modes
There are five text entry modes:
next letter.
Entering words quickly
Case change
Rapid Entry
Add Symbol
Normal alpha
Numbers only
When you press a series of keys using
checks its dictionary of common words and guesses at
the word you are trying to spell.
mode,
Note: The mode you start in depends on the task you
are doing. For example, when entering a phone number,
you’re in number mode. When entering a name for a
contact, you’re in normal text mode.
1. For each letter of the word you want, press the key
once. For example, to enter the word “any” press:
→
→
.
User Guide for the Kyocera K126C Phone
13
2. If the word doesn’t match what you want, press
Changing modes
to look at other word matches.
Sometimes you need to change modes. For example, to
enter numbers in an email address while in
you must change to
and then change back to
the address.
3. When you see the word you want, press
up.
mode,
mode, enter the numbers,
mode to complete
Entering symbols
While entering text, you can enter symbols by pressing
until you see the symbol you want. Using this
method, you have access to the following symbols:
To change text entry modes:
•
Highlight
, press
and scroll through
.
@ ?
!
-
,
&
:
’
1
the options.
To access the full set of symbols:
1. Select
2. Select
3. Press
.
Capitalization settings
Three capitalization settings are available in
modes:
Symbols and press
.
and
up or down to view the list of symbols.
4. Press the number key corresponding to the symbol
Capitalize next letter
Lower case next letter
you want.
Switching default text entry modes
Capitalize first letter of every word (in a contact)
or sentence (in a text message)
You can change the default text entry mode when
creating a text message. This setting applies only to the
message body screen, not the “Send To” screen.
If no icon appears, all letters will be in lower case.
1. Select Menu → Messages → Msg Settings →
To change capitalization settings:
•
Default Text.
Press
until the icon for the setting you
want appears.
2. Select Normal Alpha or Rapid Mode.
14
Entering Text, Numbers, and Symbols
Quick reference to text entry
This table gives general instructions for entering letters, numbers, and symbols.
To...
Do this...
Enter a letter
Use
mode and press a key until you see the letter you want. For more
information, see page 13.
Enter a number
Use
mode and press a key once to enter its number. For more options,
see page 13.
Enter a symbol
Press
until you find the symbol you want. See page 14.
Enter a space
Press
Press
.
Erase a character
.
Erase all characters
Move the cursor right or left
Change text entry modes
Change to uppercase
Change to lowercase
Select options on the screen
Press and hold
Press up or down.
Press and hold
.
.
In
mode, press
. Choose
. Choose
.
In
mode, press
.
.
Press
User Guide for the Kyocera K126C Phone
15
4
STORING CONTACTS
Use your phone’s Contacts directory to store
information about a person or company. Your phone
can hold up to 150 phone numbers.
–
–
–
–
Speed Dialing to assign a speed dial number to
your phone number.
Secret hides the number from view in the
contacts list and other areas of the phone.
Primary Number assigns phone number as
primary number for contact.
Classify Contact as Personal, Business,
or Neither. (See page 27 to set the phone to ring
differently for personal and business calls.)
Creating a new contact
1. From the home screen, enter the phone number you
want to save, including the area code.
-or-
Select Menu → Contacts → Add New →
Phone Number, then enter the phone number you
want to save, including the area code.
5. Select Save when done.
Adding a code or extension
2. Select Save New or Next.
When you save the phone number of an automated
service, you may include a pause where your phone
would stop dialing; for example, where you would wait
to dial an extension.
3. Enter a name for the contact. If you need to learn
how to enter letters, see page 13.
4. Press
right twice and select Options to add
information to the contact’s number.
1. Enter the first portion of the phone number.
–
–
Save the contact to the Contacts list.
Assign or Unassign Ringer to identify an
incoming call from this contact.
Number Type to designate a number as Work,
Home, Mobile, Pager, or Fax.
2. Select a type of pause:
–
Press
left once to select Hard Pause, which
stops dialing until you select Release. The
icon is displayed.
-or-
–
–
Add Voice Dial to add a voice dialing tag to
this number.
16
Storing Contacts
–
Press
stops dialing for two seconds, then continues to
dial. The icon is displayed.
left twice to select Time Pause, which
–
–
Classify Contact to designate the contact as
Personal, Business, or Neither.
Exit to return to the home screen.
3. Enter the remaining numbers.
Editing a phone number
1. Select Menu → Contacts.
4. Select Save New or Next and follow the prompts.
Editing or erasing a contact
To make changes to a contact, take these steps.
1. Select Menu → Contacts.
2. Select View All or Find Name to find the contact you
want to edit.
3. Highlight the contact to edit and press
4. Press down to highlight the phone number or
email address you want to edit and press
5. Choose from the following options:
.
2. Select View All or Find Name to find the contact you
.
want to edit.
3. Highlight the contact to edit and press
.
–
–
–
–
–
Send Text Msg to send a text message to that
number or email address.
View Number to see the phone number
you selected.
Add Voice Dial to add a voice dialing tag to
this number.
Speed Dialing to assign or remove the location
you use to speed dial the number.
Edit Type to assign a type: work, home, mobile,
pager, or fax. The type icon appears next to the
phone number in the Contacts list.
Erase Number to erase the number from
the contact.
4. Select Options.
5. Highlight an option and press
to select it:
–
Add New to add a new Phone Number,
Email Address, Street Address, URL, or Note
to the contact.
–
–
–
Assign Ringer or Unassign Ringer to identify an
incoming call from this contact.
Erase Contact to delete this contact from
the phone.
Edit Name to change the name that the contact is
stored as.
–
User Guide for the Kyocera K126C Phone
17
–
Erase Voice Dial to erase any voice tags from
the contact.
Edit Number to change the phone number.
Edit Voice Dial to change the voice dialing tag for
this number.
Checking the Frequent List
Press
down. The last 15 of your most frequently
–
–
called contacts appear when the Frequent List is
enabled. Scroll past the double line for an alphabetical
list of all contacts.
–
Secret to make the number secret so that it will
not appear on the screen until the lock code is
entered. Secret numbers can be called without a
lock code. (For more information, see
“Restricting calls” on page 32.)
To enable the Frequent List setting
•
Select Menu → Settings → Convenience →
Frequent List → Enabled.
Searching the Contacts directory
–
–
Primary Number to make this number
the first one that shows up when you open
the contact.
Press
down for a list of all contacts.
To quickly get down the list, enter the first letter
of the contact. The menu skips to that letter
of the alphabet.
-or-
Exit to return to the home screen.
6. Enter the new information and follow the prompts.
1. Select Menu → Contacts.
7. Select Save, if necessary.
2. Select from the following:
Finding contact information
–
–
View All: List all contacts.
Find Name: Locate a specific name. Enter part of
the contact name, then select Find.
To find a phone number or contact, you can (1) check
the frequent contacts list, (2) search the Contacts
directory, or (3) use Fast Find.
–
Speed Dial List, Voice Dial List, Business List, or
Personal List: Select a contact from a list.
18
Storing Contacts
3. Scroll down until you find the name you want, then
press
To call the contact, highlight the number and
press
.
–
.
Using Fast Find
To set Fast Find
With Fast Find, you press one or two keys to view close
matches of the number you are looking for.
•
From the home screen, select Menu → Settings →
Convenience → Fast Find → Enabled.
To use Fast Find
1. From the home screen, press the keys
corresponding to the letters of the name you want to
find. A matching contact appears.
2. When the name you want is displayed, press
to
select View.
3. Press
then press
down to select the number,
to call.
User Guide for the Kyocera K126C Phone
19
5
SENDING AND RECEIVING TEXT MESSAGES
This chapter describes how to send, receive, and erase
text messages from your phone. For information on
voicemail messages, see page 10.
–
Enter a New Address manually.
(To learn how to enter text, see page 13.)
3. To add another recipient to this message, choose
a method:
Important: The features and menus described in this
chapter may vary depending on services available in
your area. In addition, usage charges may apply to each
message. For details, check with your service provider.
–
Scroll right to Options and press
. Select
Recent List, Contacts, or Group Lists.
-or-
–
Enter a space after the first number. Then enter
another recipient manually.
Sending text messages
You can only send text messages to phones that are
capable of receiving them.
Note: You can send a message to up to 10 recipients
at once. The messages will be sent one at a time,
once to each addressee.
Creating a text message
Note: You can not send messages to
secret numbers.
1. Select Menu → Messages → New Text Msg.
-or-
4. When you are done entering addresses, select Next.
Press and hold
up.
5. Enter the message. To learn how to enter text, see
2. Enter the recipient’s phone number or
page 13.
email address:
–
To add smileys or prewritten text, press
right to Options and press
Insert... → Smileys or AutoText.
–
Select a saved number from the Recent List or
Contacts List, or select from the Group Lists you
have created. For more about group lists,
see page 25.
. Select
20
Sending and Receiving Text Messages
6. Once you have completed the message, select Send
–
Save AutoText—Save the message you have
just entered as a prewritten message, then
return to the message entry screen so you can
send the message.
to send the message immediately.
-or-
Select Options and choose one of the following:
When you have finished setting options, press
to return to the message window, then select Send to
send the message.
–
Insert...—Insert a smiley, prewritten text,
contact information, picture, or sound into your
text message.
–
Add Address—Return to the “To” screen to add
another recipient without losing the message
text. Enter the new address, then select Next to
return to the message entry screen.
Set Priority—Label the message as “Urgent.”
Callback Number—Include a callback number
with the message to let recipients know at what
number they can call you back. Select Yes to
include your own number or Edit to enter a
different callback number.
Adding a signature
The signature you create does not display in the
message creation screen; however, the signature is
included at the end of all outgoing messages and is
counted as characters in your messages.
–
–
To create a signature:
1. Select Menu → Messages → Msg Settings →
Signature.
2. Enter your signature in the text field.
3. Select
to save the setting.
–
–
Send Later—Schedule when to send
the message.
Save Message—Save the message in your Drafts
folder. This prevents the message from being
deleted if you have activated AutoErase, and
enables you to send the message to others.
If you cannot send messages
You may not be able to send or receive messages if your
phone’s memory is full, or if digital service is not
available at the time. To free up memory, erase old
messages. See “Erasing messages” on page 24.
User Guide for the Kyocera K126C Phone
21
To view the Outbox
Receiving incoming calls while creating
messages
1. Select Menu → Messages → Outbox.
2. Press
up or down through the list of messages.
•
If you don’t wish to answer the call, select Ignore.
One of the following symbols appears next to
The phone returns to the message screen.
each message:
•
To answer the call, press
. Your message is
saved to the Drafts folder. To return to the message,
select Menu → Messages → Drafts and select
Resume.
The scheduled message will be sent at the
scheduled time. You cannot cancel delivery of
the message.
Viewing the Outbox
The message cannot be sent because service is
not available. An alert appears on your phone if
the message cannot be sent.
You can check the status of messages you have sent as
long as they have been saved to the Outbox.
To set the Outbox
The scheduled message has been sent and will
be delivered as scheduled. You cannot cancel
delivery of the message.
The Outbox default is set to disabled to conserve
memory. If you want to save your sent messages:
•
Select Menu → Messages → Msg Settings →
The message has been sent to more than one
recipient.
Save to Outbox.
–
–
Select Enabled to save all sent messages to
the Outbox.
Select Prompt to alert you to choose whether or
not to save your message.
22
Sending and Receiving Text Messages
3. Press
of messages.
4. Press
up or down to scroll through the list
Retrieving text messages
When a text message is received, your screen displays
to read a message.
“1 New Text Message(s)”, along with the
symbol at
the top of your screen. The
message is urgent.
symbol flashes if the
Reading the message
The options available to you may vary. Check with your
service provider.
If you see “1 New Text Message(s)”
You can choose to:
Note: Sounds embedded in text messages will not play if
the phone is set to Silent Mode.
•
•
View the message—Press
Ignore the message—Press
.
right, then
1. If the text message is long, press
down to view
press
.
the entire message.
Note: If you receive a new message while you are
reading a message, the one you are reading will be
replaced by the new one. You can find the older
message in the Inbox:
2. When you are finished, you can Reply to the sender,
Erase the message, Save the message to your Saved
folder, or set additional Options for the message:
–
–
View Sender information.
Select Menu → Messages → Inbox.
Save New Address to save the sender’s phone
number or email address in your Contacts list.
Forward to forward the message.
Reply with Copy to reply to the message with a
copy of the original attached.
If you see the
symbol
If the symbol is flashing, the message is urgent.
–
–
1. Select Menu → Messages.
2. Select Inbox (1) to see a list of all your
–
Save AutoText to save the text from the message
as AutoText, which you can insert into other
messages. Graphics and sound will not be saved
as part of AutoText.(For more about AutoText,
see page 25.)
received messages.
New, unread messages appear in bold.
indicates an “Urgent” or “Emergency” message.
User Guide for the Kyocera K126C Phone
23
3. Select Done.
Note: You can erase a scheduled message from the
Outbox, but you cannot cancel delivery of the message.
Setting message alerts
Erasing all messages
You can set your phone to alert you of incoming text
messages or pages. For more information, see “Setting
message alerts” on page 29.
1. Select Menu → Messages → Erase Msgs.
2. Select a folder to erase all messages from: Inbox,
Outbox, Saved Folder, or Drafts. To erase messages
from all folders, select All Messages.
Erasing messages
It is a good idea to erase old messages, as messages take
up memory in your phone. You have the option of
erasing text messages and pages as you send or read
them, erasing them one at a time from the list in the
Outbox or Inbox, or erasing them all at once.
3. A message appears: “Erase all messages?” Select Yes
to erase messages or No to cancel.
Erasing messages automatically
Use this setting to have old messages automatically
erased from the Inbox when memory is low.
Erasing single messages
1. Select Menu → Messages → Msg Settings →
Auto-Erase.
1. Select Menu → Messages.
2. Press
down to find the type of text message
2. Highlight Old Inbox Msgs and press
. Older
you want to erase: Inbox, Outbox, Saved Msgs,
or Drafts.
messages will now be erased as new messages
are received.
3. Press
.
•
To disable this setting select Menu → Messages →
Msg Settings → Auto-Erase → Disabled.
4. Highlight the message to erase and press
.
5. Press
to select Erase. A notification appears:
“Erase this message?”
6. Select Yes to erase the message.
24
Sending and Receiving Text Messages
7. When finished, select Done.
Customizing message settings
To make messaging easier, you can customize settings
for sending and receiving messages.
8. To send a message to your new group, see “Sending
text messages” on page 20.
Creating and editing prewritten messages
(AutoText)
Creating group lists
You can create and save a list of multiple recipients.
Your phone stores five group lists with up to 10
recipients per list.
Your phone comes with prewritten (AutoText)
messages, such as “Please call me,” which you can
insert into the body of a text message. You can create
new ones. Your phone will store up to 20 AutoText
messages, with up to 100 characters per message.
1. Select Menu → Messages → Group Lists →
Create New.
2. Enter a name for the list. For help entering text, see
1. Select Menu → Messages → Msg Settings →
page 13.
Edit AutoText.
3. Press
to select Next.
2. To create a new pre-written message, select
4. To enter the first phone number or email address,
New AutoText.
-or-
To edit an existing pre-written message, highlight the
select an option:
–
–
–
Recent List to select numbers from your
Recent List.
New Address to enter the phone number or
email address manually.
Contacts List to select numbers or email
addresses from your phone book.
message and press
.
3. Enter or edit the text and press
to select Done.
For help entering text, see page 13.
5. Select Options to select the next number.
6. Select Recent List or Contacts then the contact
to add.
User Guide for the Kyocera K126C Phone
25
6
CUSTOMIZING YOUR PHONE
The contents of the Settings menu are as follows.
Silent Mode
Display
Call Information
Accessories
Vibrate Only
Vibrate, Ring
Lights Only
Backlighting
My Banner
Main Menu View
Auto-Hyphen
Language
Call Timers
All Calls Timer
Reset All Timers
Pwr Backlight
Headset Ring
Auto Answer
TTY Device
Norm. Sounds
Network
Hearing Aid
Keyguard
Privacy Alert
Location
Time Format
Phone Info
Guard Now
30sec auto
1min auto
5min auto
Disabled
Voice Services
Build Info
Icon Keys
Convenience
Add Voice Dial
Erase Voice Dial
Voice Training
Voice Wake-Up
Voice Answer
Fast Find
Frequent List
1-Touch Dialing
Factory Reset
Sounds
Msg Settings
Ringer Volume
Ringer Type
Voicemail Num.
Alerts
Signature
Edit AutoText
Callback Number
Save to Outbox
Auto-Erase
Security
Business Ring
Personal Ring
Earpiece Volume
Spkrphone Vol.
Key Volume
Lock Phone
Limit Calls
Lock Code
Erase Contacts
Emergency #’s
Key Length
Missed Call
Default Text
Smart Sound
Minute Alert
26
Customizing Your Phone
Note: The phone will ring when it is attached to an
external power source (such as a charger), even if all
sounds have been silenced.
Silencing all sounds
Your phone is set to make sounds when you receive
calls, press keys, navigate through menus, and receive
alerts (such as new messages).
Choosing ringers
Your phone has several preset ringers you can choose to
use for incoming calls.
You can silence all sounds and set the phone to vibrate
or light up when you receive calls and alerts.
Setting the phone to vibrate or light up
1. Select Menu → Settings → Sounds →
Ringer Type.
1. Select Menu → Settings → Silent Mode.
2. Scroll down the list to hear the different rings.
2. Choose an option and press
:
3. Press
to select a ringer from the list.
–
Vibrate Only—Causes the phone to vibrate for
the duration of the incoming call or other alert.
appears.
Vibrate, Ring—Causes the phone to vibrate for
the first 10 seconds and then ring for the
remainder of the incoming call alert.
appears.
Assigning business and personal ringers
You can assign ringers to contacts classified as business
or personal in your Contacts directory.
–
Note: To classify a contact as Business or Personal,
see page 16.
–
–
Lights Only—Causes the phone to light up for
the duration of the incoming call or other alert.
appears.
Norm. Sounds—Causes the phone to ring for the
incoming call or alert (in effect, returns phone
to a non-silent mode).
1. Select Menu → Settings → Sounds.
2. Ηighlight Business Ring or Personal Ring and
press
.
3. Select a ringer and press
.
3. Press
to return to the home screen.
User Guide for the Kyocera K126C Phone
27
2. Press
right to increase the volume, or left to
to save.
Smart Sound
decrease the volume.
This setting automatically adjusts the volume during a
call, based on surrounding noise levels.
3. Press
1. Select Menu → Settings → Sounds →
Smart Sound.
Adjusting the ringer volume
1. Select Menu → Settings → Sounds →
2. Highlight Disabled or Enabled and press
.
Ringer Volume.
2. Press
right to increase the volume, or left to
to save.
Adjusting volume
You can adjust the earpiece, speakerphone, and ringer
volume as well as key tones.
decrease the volume.
3. Press
Adjusting key tone volume
Adjusting the earpiece volume
You can change the volume of the tones the phone
makes when you press the keys.
To adjust the earpiece volume manually during a call,
press
up or down.
1. Select Menu → Settings → Sounds →
To set the earpiece volume:
Key Volume.
1. Select Menu → Settings → Sounds →
2. Press
right to increase the volume, or left to
to save.
Earpiece Volume.
decrease the volume.
2. Press
right to increase the volume, or left to
to save.
3. Press
decrease the volume.
3. Press
Setting key length
You can change duration of the tones the phone makes
when you press the keys.
Adjusting the speakerphone volume
1. Select Menu → Settings → Sounds →
1. Select Menu → Settings → Sounds →
Speakerphone Volume.
Key Length.
28
Customizing Your Phone
2. Choose Normal or Long.
3. Press to save.
•
•
•
•
Up begins a new text message.
Down lists the phone’s Contacts directory.
Left opens the Messaging menu.
Setting message alerts
You can choose how you want be alerted of incoming
voicemail, pages, or text messages.
Right accesses the ringer volume control.
Creating a shortcut to frequent contacts
By default, your phone lists your entire contacts list
when you select Contacts. You can also set the phone to
show a list of your most frequent contacts.
1. Select Menu → Settings → Msg Settings → Alerts.
2. Select the type of alert: Message Alert, Page Alert, or
Voicemail Alert.
1. Select Menu → Settings → Convenience →
3. Press
to select an option:
Frequent List.
–
–
Disabled—Turn off message alerts.
2. Select Enabled to include the list or Disabled to
Vibrate, Beep, HiYa!, Rock!, Happy, sets the
phone to alert you once when a new message
is received.
remove it.
Using the Frequent Contacts shortcut
•
From the home screen, press
down. Your 15
–
Vibe, remind; Beep, remind; HiYa! remind; Rock!
remind; Happy, remind sets the phone to notify
you once when a new message is received and
then notify you again every five minutes. To stop
most frequently called contacts appear at the top of
the list, followed by your complete Contact list.
a reminder alert, press
to select Ignore.
Using shortcuts
From the home screen, you can access shortcuts by
pressing and holding in four different directions.
These shortcuts are automatically programmed into
your phone.
User Guide for the Kyocera K126C Phone
29
2. Press
to return to the home screen. The next
Personalizing the screen
time you select Menu, you will see the menu view
Changing your banner
you selected.
The banner is the personal label for your phone.
It appears on the home screen above the time and date.
The banner can be up to 14 characters long.
Adjusting the backlighting
Your screen lights up while you are in a call or when
you press a key on the keypad. However, you can set the
length of time that bright backlighting remains on.
Note: The banner only appears if you have disabled
Airtime Balance Display.
1. Select Menu → Settings → Display →
Note: If the banner displays an “RM” at the end, the
phone is in roaming mode.
Backlighting.
2. Select an option from the list:
1. Select Menu → Settings → Display → My Banner.
–
–
Disabled—Turns backlighting off.
2. Press
right and then
to select Edit.
5 seconds, 10 seconds, 30 seconds, 1 minute —
Turn backlighting on for 5, 10, or 30 seconds,
or 1 minute after your last keypress.
3. Enter your new text. Press
to clear
any characters.
4. Press
to select Save.
–
5 sec/in call, 10 sec/in call, 30 sec/in call,
1 min/in call—Turn backlighting on for the
duration of a call, and for 5, 10, or 30 seconds,
or 1 minute after your last keypress. Note: These
settings drain the battery more quickly and
reduce talk and standby times.
Choosing a menu view
Two menu views are available:
1. Select Menu → Settings → Display → Main Menu
View, then the option you want:
–
–
Graphic displays a graphical icon view of
menu items.
List displays menu items in text format.
Note: When the keypad is locked (see “Locking the
keypad” on page 12), the backlight will not activate,
even when keys are pressed.
30
Customizing Your Phone
Setting power backlighting
Creating a secure environment
You can set backlighting to remain on when an
external power source, such as the AC adapter, is
used with the phone.
This section describes all the features involved in
securing your phone and preventing access to personal
information. All security features are shielded by a four-
digit lock code.
1. Select Menu → Settings → Accessories →
Pwr Backlight.
Changing your lock code
2. Select Always On to keep backlighting on.
The lock code is typically 0000 or the last 4 digits of
your phone number.
Note: The battery charges more slowly when power
backlighting is on.
1. Select Menu → Settings → Security.
Setting numbers to auto-hyphenate
2. Enter your four-digit lock code.
Auto-hyphenation, when enabled, automatically inserts
hyphens into your phone numbers to be consistent with
the U.S. dialing plan. For example, 1-222-333-4444.
3. Select Lock Code. A message appears:
“Change Code?”
4. Press
to select Yes and enter a new
•
Select Menu → Settings → Display →
Auto-Hyphen → Enabled.
four-digit code.
5. Enter your new lock code again.
Choosing a different time/date format
Locking your phone
1. Select Menu → Settings → Display →
When your phone is locked, you can call only
emergency numbers or your service provider number.
You can still receive incoming calls.
Time Format.
2. Highlight the option you want.
3. Press
to save the setting.
1. Select Menu → Settings → Security.
2. Enter your four-digit lock code.
3. Select Lock Phone.
User Guide for the Kyocera K126C Phone
31
4. Highlight an option:
Designating emergency numbers
–
–
Never does not lock the phone.
On power up locks the phone every time you
turn it on.
The emergency numbers feature allows you to specify
three personal phone numbers that can be called when
the phone is locked.
–
Now locks the phone immediately.
1. Select Menu → Settings → Security.
2. Enter your four-digit lock code.
3. Select Emergency #’s.
5. Press
.
Unlocking the phone
4. Select an Unassigned slot.
1. From the home screen, press
to
Note: Enter the phone number, including
select Unlock.
the area code. Do not enter 1 before the area code.
2. Enter your four-digit lock code.
5. Press
Notes:
to select Done.
Restricting calls
You can restrict the calls that can be made from your
phone to emergency numbers, your contacts, and
service provider numbers.
•
You can view these numbers only when they’re being
entered for the first time.
You cannot edit these numbers.
To make a call to an emergency number from
a locked phone, you must dial the number
(including area code) exactly as it was stored
in Emergency Numbers.
•
•
1. Select Menu → Settings → Security.
2. Enter your four-digit lock code.
3. Select Limit Calls.
4. Choose an option:
–
–
No Limit limits no calls.
Limit Out [going] calls only. Incoming calls can
still be received and answered.
–
Limit All calls, both incoming and outgoing.
32
Customizing Your Phone
Note: This feature works only when your phone is in
digital mode. You do not have the option of turning off
the locator to emergency services.
Erasing all contacts
You can erase all entries from your Contacts directory.
1. Select Menu → Settings → Security.
2. Enter your four-digit lock code.
3. Select Erase Contacts.
1. Select Menu → Settings → Network → Location.
2. Select 911 Only or Location on.
–
911 Only (default) shares your position
information only with emergency services when
you call your 3-digit emergency code (911, 000,
111, etc.).
4. Select Yes. A message appears:
“Erase ALL contacts?”
5. Select Yes and press
to erase all contacts.
–
Location on shares your position information
with your carrier’s network, in addition to
emergency services.
Network settings
Setting privacy alerts
This setting enables or disables privacy alerts. A privacy
alert is displayed whenever digital CDMA privacy is lost
or regained.
Accessory settings
Connecting to a TTY/TDD device
1. Select Menu → Settings → Network →
You can connect the phone to a TTY device for the
hearing impaired. Note: Enable TTY only when using the
phone with a TTY device.
Privacy Alert.
2. Select Enabled or Disabled.
1. Connect the TTY device to the phone.
Setting position location
2. Select Menu → Settings → Accessories →
This setting allows you to share your location
information with network services other than
emergency services (For example: 911, 111, 999, and
000) in markets where service has been implemented.
TTY Device.
3. Select OK.
User Guide for the Kyocera K126C Phone
33
3. A confirmation message appears: “There is NO
undo. Select Back to cancel. Select Reset to
proceed.” Select Reset to confirm and reset the
phone, or Back to cancel.
Using a Hearing Aid device
You can reduce interference while using the phone with
a hearing aid device by activating the phone’s T-Coil HAC
feature. Note: Enable this feature only when using the
phone with a hearing aid device.
1. Select Menu → Settings → Accessories →
Hearing Aid.
2. Select OK.
Factory reset
This function resets the phone to the state it was in when
it was shipped from the factory. It erases all saved
messages, contacts, and recent calls.
Note: A factory reset PERMANENTLY erases ALL of your
stored information!
To perform a factory reset:
1. Select Menu → Settings → Factory Reset.
2. A message appears: “Factory Reset erases all your
messages, contacts, recent calls and settings. Are
you sure you want to do this?” Select Yes to confirm,
or No to cancel.
34
Customizing Your Phone
7
TOOLS & GAMES
If you receive an incoming call alert while you
are playing Brick Attack™, the game is paused and
exited. You can return to play once the call alert ends.
Games do not remain paused if the phone is turned off
or loses power.
My Sounds
The My Sounds menu displays sounds stored on
your phone.
To access stored sounds:
1. Select Menu → Tools/Games → My Sounds.
2. Press
up or down to scroll through the sounds.
to select it:
Play allows you to listen to the sound.
Send opens a new message entry screen.
Brick Attack
The goal of this game is to eliminate bricks arranged in
levels. You send a moving ball upward using a paddle at
the bottom of the screen.
3. Highlight an option and press
–
–
1. Select Menu → Tools/Games → Brick Attack.
My Graphics
The My Graphics menu displays graphics stored on
your phone.
2. Press
to select New.
–
To pause the game, press
to Resume.
or
. Press
–
–
To move the paddle, press
To exit the game, highlight Exit and press
left or right.
To access stored graphics:
.
1. Select Menu → Tools/Games → My Graphics.
2. Press
the pictures.
3. Highlight an option and press
Send opens a new message entry screen.
up or down to scroll through
to select it:
–
User Guide for the Kyocera K126C Phone
35
4. Select Edit or Erase. Follow the prompts.
5. Press to return to the home screen.
Scheduler
The Scheduler allows you to schedule events and set
reminder alerts.
Alarm Clock
Use the Alarm Clock to set an alert for a specific time.
The alert occurs only if the phone is on.
Creating an event
1. Select Menu → Tools/Games → Scheduler.
2. Press
down to select Add Event and
1. Select Menu → Tools/Games → Alarm Clock.
2. Select Set.
press
.
3. Enter a name for the event. For help entering text,
–
–
–
Press
and minutes.
Press
minutes, and a.m./p.m.
Use the phone keypad to enter numbers.
up or down to change the hour
see page 13.
4. Select Next.
left or right to switch between hours,
5. Enter the time, length, and alarm for the event.
–
Press
minutes, and timing of alarm.
Press left or right to move between fields.
up or down to change date, hour,
3. Press
to select Done and save the setting.
–
4. When the alarm rings, select Off to turn off the alarm
6. Select Next, enter a note if required.
or Snooze to silence the alarm for 10 minutes.
7. Select Next.
Tip Calculator
The Tip Calculator helps you calculate how much tip to
include on a bill.
Viewing, editing, or erasing an event
1. Select Menu → Tools/Games → Scheduler.
2. Select View Day or View Month to find the event you
1. Select Menu → Tools/Games → Tip Calculator.
2. Enter the amount of your bill.
3. Select Next.
want to view, edit, or erase.
3. Press
up, down, left, or right to highlight an
to select it.
event and press
36
Tools & Games
4. Select the amount you want to include as a tip (10%,
6. Press
to return to the home screen.
15%, 18%, 20%, Other) and press
bill appears, including tip.
. Your total
Options
Changes the number to positive or negative.
Clears the last entry
5. To split the bill, select Split and press
.
C
.
6. Enter the number of guests and press
to select
Next. The amount each guest pays is calculated.
Inserts a decimal point.
7. Select Done.
M+ Adds displayed digit to the value stored in memory.
Calculator
MR
Displays currently stored value on screen.
Use the calculator for basic mathematical equations.
1. Select Menu → Tools/Games → Calculator.
2. Use the keypad to enter numbers.
MC
Clears value currently stored in memory.
World Clock
The World Clock lets you check times in cities around
the world in relation to local time.
3. Use
to navigate left and right to select
mathematical operations.
4. Select = to calculate the result.
1. Select Menu → Tools/Games → World Clock.
Example: Enter 5, press
, enter 2, and then press
obtain the result of 10.
right to select X, press
Your local time and date is on the first line, followed
by your selected world city and that city’s time
and date.
to select = and
5. Press
to clear the screen.
When you first access World Clock, you are
prompted to select a city.
2. Press
displayed, showing 85 world cities in
alphabetical order.
to select Cities. The Cities menu is
User Guide for the Kyocera K126C Phone
37
3. Press
You can also use the number keys
(2-9) to alphabetically tab through the list.
up or down to scroll through the cities.
4. If you search by Country, the Find Country screen
is displayed.
a. Use your number keys (2-9) to enter the
4. Press
to select a city, like Athens. The World
Clock menu is displayed again, with Athens’ time
and date.
letter(s) by which you want to search. For
example, press
once to enter the letter A.
b. Press Search.
From the World Clock menu, you can also select Search
to search by city or country.
c. Countries beginning with A are displayed, like
Afghanistan, Algeria, and Australia.
1. Select Search from the World Clock menu.
The Search By menu is displayed.
2. Select your type of search.
5. Use
to move through the list, then press
to select a country. A list of cities in that country is
displayed.
6. Use
to move through the list, then press
–
–
Press
Press
to search by City.
down, then press
to select a city.
to search
by Country.
Timer
3. If you search by City, the Find City screen
This timer counts down for a specified
amount of time. It beeps when that amount of time
has elapsed.
is displayed.
a. Use your number keys (2-9) to enter the
letter(s) by which you want to search. For
example, press
1. Select Menu → Tools/Games → Timer.
once to enter the letter A.
2. Select Set.
b. Press Search.
3. Press
and seconds. To move the cursor, press
or right.
up or down to set the hours, minutes,
c. Cities beginning with A are displayed, like
left
Anchorage, Athens, and Atlanta.
d. Use
to move through the list, then press
to select a city.
38
Tools & Games
4. Select Start and begin the countdown.
Select Stop to pause the countdown.
Select Reset to clear the timer.
5. Press
to silence the alarm.
Stopwatch
1. Select Menu → Tools/Games → Stopwatch.
2. Select Start to begin counting.
3. Select Stop to stop counting.
4. Select Reset to clear the counter.
5. Press
to return to the home screen.
User Guide for the Kyocera K126C Phone
39
8
USING VOICE RECOGNITION
Voice recognition allows you to make and
answer calls by speaking commands into the
phone’s microphone.
2. Follow the voice prompts. You will need to say
the name twice.
3. Select Add New to create a new contact
with the voice tag (see “Creating a new contact” on
Note: You cannot use voice recognition to end a call;
page 16).
you must press
.
-or-
Select Add to existing to add the voice tag to an
existing contact.
Setting up voice dialing
To make or receive calls using voice dialing, contacts
must be saved with associated voice tags.
a. Select the desired contact and press
b. Select the desired number for the contact and
press
.
Creating a voice tag for a contact
.
1. Select Menu → Contacts → View All.
Viewing entries with voice tags
2. Highlight the contact and press
.
•
Select Menu → Contacts → Voice dial list.
A list of all contacts with assigned voice
tags appears.
3. Press
down to highlight the number and
.
select
4. Highlight Add Voice Dial and press
.
Editing a voice tag
5. Follow the voice prompts. You will need to say the
name twice.
1. Select Menu → Contacts → Voice dial list.
2. Highlight the contact to edit and press
3. Highlight the phone number and press
-or-
.
1. Select Menu → Settings → Voice Services →
.
Add Voice Dial.
4. Select Edit Voice Dial and press
.
5. Follow the prompts.
40
Using Voice Recognition
4. If the name you said matches a contact in the Voice
Dial List, the phone responds: “Calling (Name).”
Remain silent to make the call, or say No to cancel.
Erasing a voice tag
1. Select Menu → Contacts → Voice dial list.
2. Highlight the contact to edit and press
3. Highlight the phone number and press
.
Note: If the phone finds multiple voice tags that
sound like the name you said, you will be asked to
verify which name you want to call. Say Yes when
you hear the correct name. Say No when you hear an
incorrect name.
.
4. Select Erase Voice Dial and press
5. Press right once and then press
Yes, or simply press to select No.
.
to select
5. When you are finished with the call, press
.
Erasing all voice tags
To erase all voice name dial recordings in your phone:
Making a call using digit dialing
When using digit dialing, you speak digits to dial a
phone number.
1. Select Menu → Settings → Voice Services →
Erase Voice Dial.
2. Select Yes. A message appears: “Erase all voice
Note: You cannot speak a string of digits. You must
speak one digit at a time and wait for the prompt.
name dial recordings?”
3. Press
right once and then press
to select No.
to select
1. From the main screen, press
. The phone
Yes, or simply press
responds: “Say a name or say ‘Dial’.”
2. Say “Dial”. The phone responds: “Speak a digit.”
Making a call using voice tags
1. If you haven’t already done so, record a voice tag for
3. Speak the first digit of the phone number you want
to call. Once the phone repeats the digit, you can
speak the next digit.
the person you wish to call.
2. From the main screen, press
. The phone
If you pause, the phone will prompt you with the
following five options. After the prompt, speak
an option.
responds: “Say a name or say ‘Dial’.”
3. Say the name of the person you want to call.
User Guide for the Kyocera K126C Phone
41
–
Say “Clear” to erase the last digit entered.
The phone responds: “Digit cleared.”
To clear the entire phone number, say “Clear”
again. When the phone prompts you with “Clear
entire phone number?”, say “Yes” to clear or
“No” to cancel.
Say “Call” to dial the number.
Say “Verify” to cause phone to repeat the set of
digits that you input.
Say “Cancel” to exit voice recognizer and return
to the main screen.
Speak a digit to enter the next digit. Once the
phone repeats the digit, you can speak the next
digit or pause to hear the prompt.
To activate the Voice wake-up setting:
•
Select Menu → Settings → Voice Services →
Voice wake-up → Enabled with ext. power.
To wake up the phone:
1. Say “Wake up” and listen for a tone.
2. Say “Wake up” again until you hear two tones.
–
–
Answering the phone
You can set your phone to (1) answer automatically or
(2) answer using a voice command.
–
–
Answering automatically
You can set your phone to answer automatically.
Note: This setting also works with the portable hands-
free headset.
Using voice features
•
Select Menu → Settings → Accessories →
Auto Answer → After 5 seconds.
You can use voice commands to make a phone call or to
answer the phone only if your phone is connected to the
AC adaptor.
Answering using voice commands
If Auto Answer is turned off, you can use a voice
command to answer an incoming call when using a
hands-free headset.
Waking up the phone
If your phone is connected to a Kyocera hands-free
headset, you can use the voice command to activate the
phone to make a phone call.
•
Select Menu → Settings → Accessories →
Auto Answer → Disabled.
42
Using Voice Recognition
To activate the Voice Answer setting:
2. Read the message and press
to continue.
Cancel returns you to the previous screen.
1. Select Menu → Settings → Voice Services→
Voice Answer.
3. Select Train All or the item you want to train.
2. Highlight Enabled and press
.
4. Follow the prompts for each word until training
is complete.
To answer a call:
When you receive an incoming call, the phone
responds: “Incoming call, answer?” If the caller is
recognized as a contact entry in your phone, then the
phone will say “Incoming call from (Name), answer?”
•
Say “Yes” or press any key except
Ignoring an incoming call
To ignore an incoming call, do one of the following:
.
•
•
Say “No” and press
to silence the alert.
Remain silent. The voice alert repeats twice
and the phone rings once, then returns to the
main screen.
Training voice recognition
If your phone is having trouble recognizing your voice,
you can train it with the commands Yes, No, and
Wake up.
1. Select Menu → Settings →
Voice Services → Voice Training.
User Guide for the Kyocera K126C Phone
43
9
GETTING HELP
•
•
The steps you took to reproduce the problem.
The phone’s Mobile Equipment Identifier (MEID).
Customer support
Your service provider’s customer support department
may be accessible directly from your phone when you
dial a number such as *611 (check with your service
provider). They can answer questions about your
phone, phone bill, call coverage area, and specific
features available to you, such as call forwarding
or voicemail.
–
To locate the MEID select Menu → Settings →
Phone Info → Build Info and scroll down to
MEID: for the 18-digit number.
Qualified service
If the problem with your phone persists, return the
phone with all accessories and packaging to the dealer
for qualified service.
For questions about the phone features, refer to the
materials provided with your phone, or visit
Phone accessories
For additional questions, you may contact the Tracfone
Customer Care Center in either of the following ways:
To shop for phone accessories, visit
www.kyocera-wireless.com/store. You may also call us
at 1-800-349-4188 (U.S.A. only) or 1-858-882-1410.
•
•
Phone: 1-800-867-7183 or 1-877-TEN-CENT
Become a product evaluator
Before requesting support, please try to reproduce and
isolate the problem. When you contact the Customer
Care Center, be ready to provide the following
information:
To participate in the testing and evaluation of Kyocera
Wireless Corp. products, including cellular or PCS
phones, visit beta.kyocera-wireless.com.
•
•
The name of your service provider.
The actual error message or problem you
are experiencing.
44
Getting Help
10 CONSUMER LIMITED WARRANTY
IN THE EVENT YOU REQUIRE WARRANTY SERVICE DO NOT
RETURN YOUR PRODUCT DIRECTLY TO KYOCERA. For warranty
service information, please contact TracFone/NET-10 at the
following telephone number from anywhere in the continental
United States: Tracfone 1-800-867-7183 / NET-10 1-877-TEN-CENT.
Kyocera Wireless Corp. (“KYOCERA”) offers you a limited
warranty that the enclosed product or products (the “Product”)
will be free from defects in material and workmanship for a
period that expires one year from the date of sale of the Product
to you, provided that you are the original end user purchaser of
the Product and provided that your purchase was made from an
authorized supplier. Transfer or resale of a Product will
automatically terminate warranty coverage with respect to that
Product. This limited warranty is not transferable to any third
party, including but not limited to any subsequent purchaser or
owner of the Product.
KYOCERA shall, at its sole and absolute discretion, either repair
or replace a Product (which unit may use refurbished parts of
similar quality and functionality) if found by KYOCERA to be
defective in material or workmanship, or if KYOCERA determines
that it is unable to repair or replace such Product, KYOCERA
shall refund the purchase price for such Product, provided that
the subject Product (i) is returned, with transportation prepaid,
to a KYOCERA authorized service center within the one year
warranty period, and (ii) is accompanied by a proof of purchase
in the form of a bill of sale or receipted invoice which evidences
that the subject Product is within the one year warranty period
(“Proof of Purchase”). After the one year warranty period, you
must pay all shipping, parts and labor charges.
This limited warranty does not cover and is void with respect to
the following: (i) any Product which has been improperly
installed, repaired, maintained or modified; (ii) any Product
which has been subjected to misuse (including any Product used
in conjunction with hardware electrically or mechanically
incompatible or used with accessories not approved by
KYOCERA), abuse, accident, physical damage, abnormal
operation, improper handling, neglect, exposure to fire, water
or excessive moisture or dampness or extreme changes in
climate or temperature; (iii) any Product operated outside
published maximum ratings; (iv) cosmetic damage; (v) any
Product on which warranty stickers or Product serial numbers
have been removed, altered, or rendered illegible; (vi) cost of
installation, removal or reinstallation; (vii) signal reception
problems (unless caused by defects in material and
workmanship); (viii) damage the result of fire, flood, acts of
God or other acts which are not the fault of KYOCERA and which
the Product is not specified to tolerate, including damage caused
by mishandling, shipping and blown fuses;
(ix) consumables (such as fuses); or (x) any Product which has
been opened, repaired, modified or altered by anyone other
than KYOCERA or a KYOCERA authorized service center.
USE ONLY KYOCERA APPROVED ACCESSORIES WITH KYOCERA
PHONES. USE OF ANY UNAUTHORIZED ACCESSORIES MAY BE
DANGEROUS AND WILL INVALIDATE THE PHONE WARRANTY IF
User Guide for the Kyocera K126C Phone
45
SAID ACCESSORIES CAUSE DAMAGE OR A DEFECT TO THE
PHONE.
EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION OR
ADDITION TO THIS WARRANTY.
KYOCERASPECIFICALLY DISCLAIMS LIABILITY FOR ANY AND ALL
DIRECT, INDIRECT, SPECIAL, GENERAL, PUNITIVE, EXEMPLARY,
AGGRAVATED, INCIDENTAL OR CONSEQUENTIAL DAMAGES,
EVENIF ADVISED OF THE POSSIBILITY THEREOF, WHETHER
FORESEEABLE OR UNFORESEEABLE OF ANY KIND
Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or allow limitations on
how long an implied warranty lasts, so the above limitations or
exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may
also have other rights which vary from jurisdiction to
jurisdiction.
WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSS OF
PROFITS, UNANTICIPATED BENEFITS OR REVENUE,
ANTICIPATED PROFITS ARISING OUT OF USE OF OR INABILITY
TO USE ANY PRODUCT (FOR EXAMPLE, WASTED AIRTIME
CHARGES DUE TO THE MALFUNCTION OF A PRODUCT) OR
CONTRIBUTION OR INDEMNITY IN RESPECT OF ANY CLAIM
RELATED TO A PRODUCT.
IN THE EVENT YOU REQUIRE WARRANTY SERVICE DO NOT
RETURN YOUR PRODUCT DIRECTLY TO KYOCERA. For warranty
service information, please contact TracFone/NET-10 at the
following telephone number from anywhere in the continental
United States: Tracfone 1-800-867-7183 / NET-10 1-877-TEN-
CENT.
REPAIR OR REPLACEMENT OF A DEFECTIVE PRODUCT OR
REFUND OF THE PURCHASE PRICE RELATING TO A DEFECTIVE
PRODUCT, AS PROVIDED UNDER THIS WARRANTY, ARE YOUR
SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF THE
LIMITED WARRANTY, AND SUBJECT TO THIS WARRANTY, THE
PRODUCTS ARE APPROVED AND ACCEPTED BY YOU "AS IS".
KYOCERA MAKES NO OTHER WARRANTIES, REPRESENTATIONS
OR CONDITIONS OF ANY KIND, ORAL OR VERBAL, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE, WITH RESPECT TO THE
PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR AGAINST INFRINGEMENT OR
ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF
TRADE USAGE OR OUT OF A COURSE OF DEALING OR COURSE
OF PERFORMANCE. NO DEALER, DISTRIBUTOR, AGENT OR
46
Consumer Limited Warranty
INDEX
Numerics
1-touch dialing, 10
emergency mode, 11
exit emergency mode, 11
position location, 3, 33
M
symbol mode, 14
T
memory, saving, 24
menu view, 30
My Sounds, 35
N
A
technical support, 44
text entry, 13
text messages, 20
time format, 31
timer, 38
timing calls, 11
Tools
erasing
accessories, 42
alarm clock, 2, 36
alerts
for messages, 29
for missed calls, 8
assigning business and personal finding contact information, 18
ringers, 27
auto-hyphenation, 31
AutoText, 25
B
contact entries, 33
text messages, 24
number mode, 13
O
F
fast find, 19
outbox, 22
P
frequent contacts, 18
alarm clock, 36
calculator, 37
scheduler, 36
stopwatch, 38
timer, 38
phone numbers
editing, 17
G
games
verifying your own, 6
Brick Attack, 35
My Sounds, 35
H
phone, unlocking, 31
position location, 3, 33
banner, 30
battery, 1
blocking outgoing calls, 32
Brick Attack, 35
C
world clock, 37
TTY/TDD, 33
R
hands-free headset, answering
using voice, 42
hard pause, 16, 18
recent call icons, 8
resetting the phone, v
ringers
U
unlocking the phone, 32
V
calculator, 37
call counters, 11
calls
answering, 7
missed, 8
redialing, 7
contacts
voice dialing, 40
contacts directory, 16
countdown timer, 38
D
I
choosing types, 27
silencing, 6
volume, 28
vibrate, 3, 27
Voice Answer, 42
voice dialing, 40
voice recognition, 40
voicemail, 10
setting up, 6
volume
icons, 2
inbox, 23
K
S
keyguard, 2, 12
keypad, locking, 12
saved phone numbers
editing, 17
scheduler, 36
screen icons, 2, 13, 22, 27
secret contacts, 9
security, 31
shortcuts, 29
silent mode, 3, 27
sound files, 35
speakerphone, 3
stopwatch, 39
L
lights-only mode, 3, 27
limiting calls out, 32
lock code, 31
locking
earpiece, 8, 28
key beep, 28
ringer, 28
digital mode, 2
E
W
warranty, 45
world clock, 37
keypad, 12
phone, 31
emergency
calls, 11
User Guide for the Kyocera K126C Phone
47
|