®
PORTABLE CD PLAYER
WITH AM/FM RADIO RECEIVER
MODEL CD-110
OPERATING INSTRUCTIONS
PLAYS MUSIC COMPACT DISCS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT PLAY
RECEIVES AM/FM BROADCASTS
POWER LED INDICATOR
2 WAY POWER - AC/DC
REQUIRES 6 SIZE D BATTERIES (not included)
PLEASE READ CAREFULLY BEFORE USE
IB-CD110(SY)-WM-E-V1
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the
antenna system is grounded so as to provide some protection against voltage surges and
built up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70 provides
information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
on the bottom of the set.
2
IB-CD110(SY)-WM-E-V1
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you cant resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
IB-CD110(SY)-WM-E-V1
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
AC SOCKET
To a wall outlet
NOTE: One blade of plug
and outlet is wider.
Battery compartment
(on the bottom of the set)
1. Connecting the AC power
cord
TIP
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again.
The plugs are polarized
and only fits one way into
the wall outlet and back of
the set.
Insert one end of the supplied AC power cord
(located in the battery compartment) into the socket
located at the rear of the player, and the other end
to the wall outlet.
2. Using the player on batteries
Insert 6 size D batteries (not supplied) into the
battery compartment.
To use the player on batteries, disconnect the AC
power cord from the player.
TIP
Replace the batteries
when the POWER lamp
dims or when the player
stops operating. Replace
all the batteries with new
ones. Before you replace
the batteries, be sure to
take out the CD from the
player and remember to
check the Battery Safety
Instructions on Page 3.
C
C
C
C
C
C
REMOVE
BATTERY
DOOR
4
IB-CD110(SY)-WM-E-V1
PLAYING A CD
3
2
1
4
Connect the supplied AC power cord or batteries (see page 4).
Rotate the FUNCTION
switch to the CD position.
The POWER lamp will turn
1
2
on.
POWER lamp
Press the OPEN button to
open the CD door and place
the
CD
in
the
CD
compartment. The label side
of the CD should face
upward.
OPEN
NOTE: Make sure the handle
is folded in its position,
otherwise the CD door will be
barred by the erected handle.
Close the CD DOOR by
pushing it down. The display
will show the total tracks on
that CD.
3
4
TRACK
Press the CD PLAY button.
The PLAY/PAUSE lamp will
be steady on, the player
plays all the tracks once.
TRACK
Track
number
PLAY/PAUSE
lamp
5
IB-CD110(SY)-WM-E-V1
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
OPEN BUTTON
STOP
PLAY
FUNCTION SWITCH
HEADPHONES
JACK
VOLUME CONTROL
TIP
(at the left side of the set)
SKIP/SEARCH
When CD play is
paused, the PLAY/
PAUSE lamp will
flash and no music
will play.
To
Press or Adjust
Adjust the volume
VOLUME control (on left side)
Stop playback
STOP
To resume play,
press the PAUSE
button again, the
PLAY/PAUSE lamp
will stop flashing
and music will play.
PLAY/PAUSE
The PLAY/PAUSE lamp will
flash during pause. Press
again to resume play after
pause.
Pause playback
Go to the next track
TIP
FORWARDS
BACKWARDS
If you bump the set
during CD play, the
music will stop or
Go back to the previous
track
skip for
a
few
or
seconds. This is
normal for this type
of player.
Press and hold down while
playing until you find the
point you like.
Locate a point in a song
Insert your headphone plug
into the HEADPHONES jack
(Headphones is not included).
To enjoy the music
without disturbing others
Press the OPEN button
(press STOP first).
Remove the CD
Rotate the FUNCTION switch
to OFF position.
Turn off the power
6
IB-CD110(SY)-WM-E-V1
PLAYING CD TRACKS REPEATEDLY
(REPEAT PLAY)
You can play CD tracks over and over in normal or program play modes (see page 8).
FUNCTION
SWITCH
BACKWARD
REPEAT
BUTTON
PLAY/PAUSE
FORWARD
REPEAT
LAMP
PROGRAM
LAMP
1. Rotate the FUNCTION switch to CD position.
or
2. Select the track by pressing
3. Press the CD REPEAT button.
, and then press
.
Press
To repeat
Repeat Lamp
a single track (song)
Press the REPEAT button once
Press the REPEAT button twice
Flashing
Steady on
all the tracks (all songs)
programmed tracks
During programmed play, press
the REPEAT button twice
Steady on
(the PROGRAM
lamp also on)
To cancel Repeat Play
Press the REPEAT button until the REPEAT lamp goes off.
7
IB-CD110(SY)-WM-E-V1
SELECTING YOUR OWN MUSIC PLAYING ORDER
(Programmed Play)
You can make a program of up to 16 tracks in the order you want them to be
played.
PROGRAM
BUTTON
PROGRAM LAMP
1. Rotate the FUNCTION switch to CD position.
2. Press the PROGRAM button. The letters Pr and
the PROGRAM lamp will flash.
3. Press
or
to select the tracks you want to
PROG.
program in the order you want.
4. Press the PROGRAM button to confirm. The letters
Pr and the PROGRAM lamp will flash.
5. Repeat steps 3 and 4. You can program up to 16
tracks.
6. Press
to start your programmed play. The
PLAY/
PAUSE
PROGRAM lamp will be steady on.
NOTE: Programming is only done during stop mode.
TRACK
PROG.
To check the order of tracks before play
Press the PROGRAM button, the programmed track number appears in the display
automatically.
PLAY/
PAUSE
TRACK
PROG.
PROGRAM
To change the current program
Just create a new program following the programming procedure.
PROGRAM
PROG.
To cancel Program Play
Press the STOP button twice and the PROGRAM lamp goes off.
STOP
IB-CD110(SY)-WM-E-V1
8
LISTENING TO THE RADIO
4
1
2
3
Connect the supplied AC power cord or batteries (see page 4).
Rotate the FUNCTION switch to
RADIO position, the POWER
lamp will be on.
1
2
Rotate the BAND switch to the
proper band position (AM or FM)
that you want.
Tune into the station you prefer
using the TUNING control (at the
right side of the set). Adjust for
the clearest sound.
3
4
The station you are listening will
show in the window of the AM/
FM dial lens.
9
IB-CD110(SY)-WM-E-V1
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
FUNCTION SWITCH
VOLUME
CONTROL
To
Rotate
TIP
Next time you want to
Adjust the volume
VOLUME control (at the
left side of the set)
•
listen to the radio, just
Rotate the FUNCTION
switch to RADIO. The
player automatically
starts playing the
Rotate the FUNCTION
switch to OFF position
Turn off the Radio
previously
station.
tuned
To improve broadcast reception
In steel frame buildings,
you can improve AM
reception by bringing
•
the set closer to
window.
a
Change position of
the antenna for FM.
Move the set itself
for AM.
10
IB-CD110(SY)-WM-E-V1
PRECAUTIONS
On Safety
On Power Sources
For battery operation, use 6 size D
batteries. We recommend alkaline
batteries for longer life.
The laser beam used in the CD
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet. Refer servicing to
qualified personnel only.
When the batteries will not be used
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage or corrosion.
Should any solid object or liquid fall
into the player, unplug the player, and
have it checked by qualified personnel
before operating it any further.
On Operation
If the player is brought directly from a
On Placement
Do not leave the player in a location
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate.
Do not place the player on an inclined
or unstable place.
Do not place anything within 1 inch of
the back of the cabinet. The
ventilation holes must not be covered
for the player to operate properly and
prolong the life of its components.
This CD player is designed to be
played on
a
stable no vibration
position. If you bump the set during
CD play, the music will stop or skip for
a few seconds. This is normal for this
type of player.
If the player is left in a car parked in
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the
sun.
If you have any questions or problems
concerning your player, please contact
our customer service department.
Since a strong magnet is used for the
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the player to
prevent possible damage from the
magnets.
11
IB-CD110(SY)-WM-E-V1
PRECAUTIONS (continued)
Notes on CDs
MAINTENANCE
Cleaning the Lens
If the lens becomes dirty, it may
cause a skipping of sound during CD
operation. Clean with a commercially
available lens cleaner and blower.
Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
Do not use solvents such as benzene,
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Do not expose the CD to direct
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened
with a mild detergent solution. Do
not use any type of abrasive pad,
scouring powder, or solvent, such as
alcohol or benzene.
Do not stick paper or stickers on the
CD, nor scratch the CD.
After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
12
IB-CD110(SY)-WM-E-V1
TROUBLE SHOOTING
Problem
Remedy
Connect the AC power cord to a wall
outlet securely and make sure AC cord is
inserted properly in the back of the set.
Make sure the batteries are inserted
correctly and they are fresh.
The power is not on.
Make sure the FUNCTION switch is at the
right position as you want.
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
appears in the display
Insert the CD with the label side up.
even when a CD is inside.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
CD does not play.
Take out the CD and leave the CD DOOR
open for about an hour to dry moisture
condensation.
Make sure the FUNCTION switch is in the
CD position.
Clean the CD, or replace it if the CD is
badly damaged.
Place the player in a location free from
vibration.
The sound drops out.
Check if your batteries are fresh.
(NOTE: Your batteries may have some life
in them, enough for radio use, but not
enough for CD play.
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
The sound is weak or has
poor quality.
IB-CD110(SY)-WM-E-V1
13
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 12Watts
DC 9V (6 size D batteries)
(Alkaline batteries are recommended)
Speakers:
2 - 3 8 ohm
1.5W/channel
Width: 13
Output power:
Dimensions:
1
Depth: 10 /
2
Height: 5
Weight: 4.5LBs (without batteries)
CD Section
Plays disc type:
Any normal music CD used in portable players
760 - 800 NM
Laser wavelength:
Tracking method:
Frequency response:
3 - spot error detection
50Hz - 15kHz +1/-2dB
3.86 mm lens
NOTE: This CD player will only play NORMAL music CDs (or CD-R CDs).
This set will not play CDRW encoded discs.
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 kHz
LENOXX reserves the right to make design and specification changes for
product improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR
LACQUER FINISH.
For customer service
Dial 1-800-315-5885
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2001 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
IB-CD110(SY)-WM-E-V1
14
|