LINN KARIK NUMERIK
C O M P A C T D I S C P L A Y B A C K S Y S T E M O W N E R S M A N U A L
IMPORTANT SAFETY INFORMATION
Explanation of symbols used in this manual and on the product:
This symbol is intended to alert the user to the presence of
uninsulated dangerous voltages within the enclosure of
sufficient magnitude to cause electric shock.
This symbol is intended to alert the user to the presence of
importance maintenance and servicing information in the
instruction and service manuals.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: SHOCK HAZARD. DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
CAUTION: REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
ATTENTION: DEBRANCHER AVANT DE REMPLACER LE FUSIBLE.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
i
MAINS PLUGS
This appliance is supplied with a non-rewireable mains plug for the intended
country.
Replacement mains leads can be obtained from your Linn retailer.
Should you need to change the plug please dispose of it carefully.
A plug with bared conductors is dangerous if engaged in a live socket.
The Brown wire must be connected to the Live (Line) supply pin.
The Blue wire must be connected to the Neutral supply pin.
The Green/Yellow wire must be connected to the Earth (Ground) supply pin.
Please contact your retailer or a competent electrician if you are in any doubt.
GENERAL SAFETY INSTRUCTIONS
1. Read Instructions. Read the safety and operating instructions before
operating the appliance.
2. Retain Instructions. Retain the safety and operating instructions for future
reference.
3. Heed Warnings. Observe all warnings on the appliance and in the
operating instructions.
4. Follow Instructions. Follow all operating and use instructions.
5. Water and Moisture. Do not use the appliance near water, for example near
a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near
a swimming pool and the like.
6. Carts and Stands. Use only with a cart or stand that is recommended by the
manufacturer.
6a. An appliance and cart combination should be used with care. Quick stops,
excessive force and uneven surfaces may cause the appliance and cart
to overturn.
7. Wall or Ceiling Mounting. Mount to
recommended by the manufacturer.
a
wall or ceiling only as
8. Ventilation. Site the appliance so that its location or position does not
interfere with its proper ventilation. For example the appliance should not
be situated on a bed, sofa, rug or similar surface that may block the
ventilation openings; or placed in a built-in installation such as a
bookcase or cabinet that may impede the flow of air through the
ventilation openings.
9. Heat. Site the appliance away from heat sources such as radiators, heaters,
stoves or other appliances (including amplifiers) that produce heat.
10. Power Sources. Connect the appliance to a power supply only of the type
described in the operating instructions or marked on the appliance.
ii
11. Grounding or Polarization. Do not defeat the precautions taken to ground or
polarize the supply to the appliance.
12. Power Cord Protection. Route power cords so that they are not likely to
be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, power sockets and at the point where
they exit from the appliance.
13. Protective Attachment Plug. As a safety feature the product is equipped
with an attachment plug containing overload protection. See the instruction
manual about resetting or replacing the plug. Should the plug need
replacing ensure that a replacement is used which has the same overload
protection as the original.
14. Cleaning. The product should be cleaned only as recommended by the
manufacturer.
15. Power lines. An outdoor antenna should be located away from power lines.
16. Outdoor Antenna Grounding. If an outdoor antenna is connected to the
tuner/receiver ensure that the antenna system is grounded to provide some
protection against voltage surges and static build up.
In the USA see article 810 of the National Electrical Code ANSI/NFPA 70
concerning installation requirements.
17. Non-use periods. Unplug the power cord from the outlet if the product will
be unused for a long period of time.
18. Objects and liquid entry. Take care not to let objects or liquids fall into the
product.
19. Damage requiring service. The product should be serviced by qualified
personnel if:
a) the power cord or plug has been damaged.
b) objects or liquid have fallen into the product.
c) the product has been exposed to rain.
d) the product does not appear to operate normally or exhibits a marked
change in operation.
e) the product has been dropped or the enclosure damaged.
20. Servicing. Don’t attempt to service the product beyond that described in the
operating instructions. All other servicing should be referred to qualified
service personnel.
iii
UK USERS PLEASE READ THIS IMPORTANT SAFETY INFORMATION.
FUSE REPLACEMENT
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug
contains a 5 Amp fuse.
If the fuse has blown it can be replaced:
a) pull out the red fuse cover/carrier.
b) remove and dispose of the blown fuse.
c) fit a new 5 Amp BS1362 approved fuse into the carrier and push the
carrier back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use
the plug. Contact your Linn retailer to obtain a replacement fuse cover. Fuses
are for fire protection and do not protect against electric shock.
MAINS PLUG REPLACEMENT
Should your mains plug need replacing and you are competent to do this
proceed as follows. If you are in doubt contact your Linn retailer or a
competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection points
of most quality plugs.
Attach the wires securely to their respective points. The Brown wire must
go to the Live pin, the Blue wire must go to the Neutral pin and the
Green/Yellow wire must go to the Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding
the outer sheath of the cable firmly and that the wires are correctly
connected.
iv
USIC is very important for people. It stimulates the imagination,
helps them relax, can change their mood, and of course provides
entertainment and pleasure.
M
A good hi-fi works well enough to deliver these benefits. It also helps you
appreciate music you never thought you would.
At Linn we devote our energy to improving standards of music reproduction,
because we know that the better the sound the more you'll enjoy music at
home.
The addition of any Linn component will improve the sound quality of your
system. Linn has a policy of continuously improving its equipment allowing
customers to retro-fit most product upgrades.
1
2
NTRODUCTION The Linn KARIK CD Transport and the Linn NUMERIK
digital-to-analogue convertor represent the culmination of several years
research and development, and achieve uncompromised performance
I
standards providing you with an outstanding musical source.
The Linn KARIK CD Transport incorporates an internal digital-to-analogue
convertor (DAC), enabling the KARIK to be used in its own right as a single-box
CD player of the highest possible quality. Consistent with Linn’s philosophy of
ensuring long-term upgrade capability for all our products, the KARIK has the
necessary digital outputs and CD-SYNC input to allow it to be connected to
the Linn NUMERIK at any time in the future, without modification.
The KARIK operates to the highest level of the Compact Disc specifications. It
features advanced error correction, making it tolerant of imperfect disc quality,
giving a significant performance advantage with any chosen disc. It can be
operated from the remote control handset supplied, or directly using the
concealed controls on the front panel.
The Linn NUMERIK digital to analogue converter has been developed from our
professional studio recording system to make this ultimate level of technology
available to the home listener. The NUMERIK is an oversampled DAC using
20-bit convertors which eliminate the low-level distortions found on most
multi-bit DACs. The NUMERIK introduces innovative clock circuitry which cuts
out sound degradation caused by timing jitter. The performance of any high
quality CD Transport with a digital output will be enhanced when combined
with the NUMERIK. Optimum performance is achieved when the NUMERIK is
partnered with the KARIK CD Transport.
3
INSTALLATION Unpack the KARIK and NUMERIK and retain the packing for
future transportation.
Your Linn Dealer is responsible for ensuring correct installation of the KARIK
and NUMERIK. He will be pleased to provide information, address your
queries and resolve any problems. If this is not possible, please contact
the Linn Products factory in Scotland, or your national distributor. For your
information some tips regarding set-up, interconnections and operation are
given below.
WARNING Use the earthed moulded mains lead supplied. Never use an
unearthed plug or adaptor.
WARNING
THIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in this mains lead are coloured in accordance with the following
code:
Green-and-yellow:
Blue:
Brown:
Earth
Neutral
Live
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green-and-yellow must be connected to the
terminal in the plug, which is marked with the letter E, or the earth symbol or
coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
4
SET-UP
KARIK OUTPUT CONNECTIONS The KARIK has two stereo AUDIO OUTPUTS
provided for connection to your preamplifier and direct connection to another
system such as a multi-room application.
The KARIK also has two high quality S/P-DIF digital audio outputs. The
ELECTRICAL OUTPUT is connected to the NUMERIK via the 75 Ohm BNC - BNC
lead provided, or to other external audio processors with phono inputs by the use
of a BNC - Phono adaptor.
The DIAGNOSTIC OUTPUT CONNECTOR is used by your dealer to carry out
diagnostic checks on your KARIK to guarantee quality. He will be able to check for
tracking errors, error rates and most importantly, laser performance. This is an
extremely efficient method of service back-up, assuring you of our continued
product support.
KARIK INPUT CONNECTIONS The KARIK’s SYNC INPUT connection is made
from the NUMERIK by means of a high quality audio phono - phono lead. With this
lead in place the NUMERIK adopts ‘master’ mode operation and superior audio
performance is achieved. When this lead is not in place the NUMERIK will adopt
‘slave’ mode and will operate in a conventional manner.
SLEEP MODE If the DISPLAY switch on the back panel is in, and power is
applied, the KARIK will enter a ‘sleep’ mode. Twenty seconds after the last
operation the display will turn off (show two dashes). Actuation of the door,
front panel controls or remote control will waken the display. This feature, shared
by the Linn Kairn pre-amplifier and Kremlin tuner, saves power and draws less
attention to the products, if required.
When the display switch is out, and power is re-applied, the display will remain
lit continuously.
5
NUMERIK INPUT CONNECTIONS The NUMERIK has two S/P-DIF inputs,
both on BNC connectors. CHANNEL 1 is intended for use with the Linn KARIK CD
transport. CHANNEL 2 is provided for connection to any other high quality digital
audio source.
NUMERIK OUTPUT CONNECTIONS Two stereo AUDIO OUTPUTS are
provided for connection to your pre-amplifier, and direct connection to another
system such as a multi-room application.
A
SYNC OUTPUT is provided for each digital input. This should be connected to
the corresponding SYNC INPUT on the Linn KARIK CD transport to facilitate
Master Mode operation which eliminates data - related clock jitter.
INDICATOR LIGHTS These are located on the rear panel and are there to assist
when setting up the NUMERIK.
When a particular input channel is selected the corresponding input channel
indicator is lit.
When Master Mode is in operation, the indicator labelled MASTER is lit.
When the NUMERIK is correctly synchronised to an input signal, the indicator
labelled LOCK is lit. When this light is off or flashing, the NUMERIK cannot
synchronise to the input signal. This may be due to incorrect connections. Check
all the leads are plugged into their correct sockets. If LOCK is still not achieved,
there is a more fundamental problem, therefore please contact your Linn dealer.
When the sample rate is 44.1 kHz , the light labelled 44.1 kHz is lit. When the
sample rate is 48 kHz , this light is off.
6
ADDITIONAL CONNECTIONS
REMOTE IN/OUT CONNECTIONS The remote in and out facility on the KARIK is
intended for use in a distributed system. This facility enables quick and efficient
access by remote control, to various Linn products throughout your home.
DISTRIBUTED SYSTEM
REMOTE CONTROL LINK UP
7
CD HANDLING
Forgetting all the hype that surrounded the launch of compact disc -
1. Never handle the playing surface of the disc.
2. Scratches on either side of the disc activate correction circuits on a transport.
This process complicates the retrieval of information and may result in
degradation of sound quality.
3. The perimeter of the CD centre hole must be kept in pristine condition, as a
transport relies on an accurate fit of the hole to the spindle to maintain the
highest performance.
4. Keep your disc away from excessive heat. Warped discs complicate the
retrieval of information and may result in degradation of sound quality.
As a general rule CDs should be looked after with the same care as your records.
Remember, the condition of both are vital in achieving the best results from your
hi fi system.
OPERATION The KARIK and NUMERIK have been designed for low power
consumption and cool running. We recommend that they are switched off when
not in use.
SKIP
SEARCH
INDEX
STOP PAUSE TIME TRACK REPEAT DIGITAL
8
KARIK OPERATION Operating the KARIK with the remote control provides
the most efficient method of accessing the functions, and you will probably
use this method on a day-to-day basis. Manual operation of the KARIK, using
the buttons on the control area, is described below.
DISPLAY MODES
TRACK shows TRACK and INDEX information.
At power-up the KARIK will select TRACK display mode. Whenever a disc
stops playing, the KARIK will revert to TRACK mode. When enabled, this mode
will display TRACK and INDEX information.
TIME shows TIME information.
There are four TIME modes: TRACK TIME, which shows time into track;
REMAIN TRACK TIME, which shows the remaining time on the track;
TOTAL TIME, which shows time into disc from start;
9
and TOTAL REMAIN TIME which shows the remaining time on the disc.
Repeated pressing of the TIME button selects the four time modes.
NOTE TRACK and TIME modes are accessed on the remote control handset
via the DISPLAY button.
POWER ON
To switch the KARIK on, press the POWER button. When there is no disc in
the drawer, TRACK, INDEX, DIGITAL and PLAY legends will light and TRACK
display will show ‘00’. The PLAY legend will go out after approximately
8 seconds.
If there is a disc in the drawer (either open or closed) when the KARIK is
switched on, the disc will be loaded and the first track will start to play
automatically.
OPEN
Open the drawer by pressing OPEN once. The second press, or pushing the
drawer, loads the disc into the KARIK.
When the disc is loaded, the TOTAL and TIME legends light and the display
shows briefly the total playing time of the disc in minutes and seconds.
TRACK and INDEX legends will then light and the total number of tracks on
the disc will be displayed.
10
PLAY
To close the drawer and start play, press PLAY once. The TRACK, INDEX,
PLAY and DIGITAL legends will light and the display will show TRACK 1,
INDEX 1, if left to continue, all tracks on the disc will be played, the display
incrementing at the start of each new track and index point.
If you wish to hear the current track from its start point, press PLAY a
second time and the KARIK will return to the beginning of the track and play
will resume. When in time mode, the display will show the current track
number before reverting to the selected time mode.
After completing all the tracks on the disc, the display shows either the total
number of tracks on the disc, or the total playing time of the disc followed by
the total number of tracks on the disc, depending on TRACK or TIME mode
selection.
PAUSE
For a break in play press PAUSE ; the PAUSE legend will light. To release the
pause function and continue play, press PAUSE or PLAY
SKIP or SEARCH commands can be used while in pause mode. This causes
the pick-up to move to a new position. To start play from the new position
press PAUSE or PLAY
If in TRACK mode, TRACK and INDEX display values will remain current until
PAUSE or PLAY is pressed to continue play. When in TIME display mode, the
display will show current selection time.
STOP
Press STOP once to stop the disc.
If in TRACK display mode, TRACK and INDEX legends are lit and the display
shows the total number of tracks on the disc. When in TIME display mode,
TOTAL and TIME legends are lit and the display will show the total playing
time of the disc in minutes and seconds, before reverting to TRACK mode.
11
SKIP FORWARD/SKIP BACKWARD
To select a different track press SKIP i or u SKIP and the pick-up will
advance to the start of the next track, or go back to the start of the current
track.
Pressing and holding will go forwards or backwards through all the tracks in
turn until the button is released.
SKIP i or u SKIP can be used in the same way when the disc is stopped
and audio is muted. When the selected track is reached, press PLAY to
start the disc.
If in TRACK display mode, the display will increment or decrement to the
selected track number. PLAY, TRACK and INDEX legends will be lit. If in TIME
display mode, the display will show the selected track and index numbers
before reverting to the selected TIME display mode.
INDEX FORWARD/INDEX BACKWARD
Some tracks are sub-divided into smaller sections called index points.
To select a different index point press INDEX
or
INDEX once, and the
2
1
pick-up will jump forward to the next index point, or backward to the start of
the current index point.
If in TRACK display mode, the INDEX display changes to the selected index
number. The TRACK and INDEX legends are lit. When in TIME display mode,
the selected index number is displayed, before reverting to the TIME mode
previously selected.
SEARCH FORWARD/SEARCH BACKWARD
To scan through the disc, press and hold SEARCH y or t SEARCH for
fast scan forward or backward through the tracks. The scanning rate will
increase gradually. Audio level is reduced, but audible. Release the button to
start play, audio will return to normal volume.
When searching forward and the end of the disc is reached, the display will
show the total number of tracks on the disc or the total playing time of the
disc depending on whether TRACK or TIME display mode is selected.
12
When searching backwards and the start of the first track is reached, the disc
will start to play automatically.
If in TRACK display mode, the display will increment when the button is held
past a track boundary. If in TIME display mode, the display will increment or
decrement depending on the time mode selection.
REPEAT
To repeat all tracks, or selected sections of the disc, press REPEAT . To
repeat the complete disc at any time during play, press REPEAT . The REPEAT
legend will light.
To cancel disc repeat, and resume normal play, press REPEAT a further two
times.
Play between two points can be repeated by selecting the start point using
SKIP, SEARCH or INDEX. Press REPEAT to store the start point. The REPEAT
legend will light. Select the end of the repeat section using SKIP, SEARCH or
INDEX. Again press REPEAT to store the end point. NOTE Do not press
REPEAT too quickly but allow time for the KARIK to return to play mode.
This passage will be repeated continually from the start point. To cancel
repeat, press REPEAT again while in this mode; normal play will proceed.
If in TRACK display mode, the track numbers between the start and end
points will be shown. The TRACK and INDEX legends will be lit. When in TIME
display mode, the time display will increment or decrement depending on the
time mode selection.
DIGITAL AUDIO OUTPUT
To switch the digital audio output on and off, press DIGITAL . Digital output
is enabled at power-up and the DIGITAL legend is lit. When the KARIK is
connected to CHANNEL 1 on a NUMERIK, the DIGITAL button acts as an
input selector for the NUMERIK.
DIGITAL OUTPUT ‘ON’ - KARIK selected on NUMERIK.
DIGITAL OUTPUT ‘OFF’ - Channel 2 (eg. DAT) selected on NUMERIK.
13
REMOTE CONTROL
One feature of the remote control is that you can enter a track number
directly. Since the numeric section of the remote handset can be used for the
Compact Disc, Preamp and Tuner functions, to link the numbers to the
KARIK player the previous button pressed has to be one from the Compact
Disc section of the handset.
To enter a track number from 1 to 9, press the corresponding digit on
the remote control for less than 0.5 seconds. When the digit is pressed it is
shown on the display. When the button is released, the KARIK plays the
selected track.
To enter a track number from 10 to 99, press and hold down the button for the
first digit. The digit will be shown on the display. After 0.5 seconds, the
displayed digit will move one place to the left and a dash appears in the
original digit position. Press the button for the second digit. The dash on the
display is replaced by the second digit of the track number and the KARIK
plays the track.
NUMERIK OPERATION To switch the NUMERIK on, press the POWER
button. The power indicator light will illuminate. After about five seconds, the
audio output will unmute, and the NUMERIK is ready for operation.
Channel 1 is selected if there is an S/P-DIF signal on the Channel 1 input,
otherwise Channel 2 is selected. This allows the DIGITAL AUDIO OUTPUT
enable facility on the KARIK to be used as an input selector on the NUMERIK.
44.1 kHz or 48 kHz sample rates are automatically selected.
The KARIK’s SYNC Input connection is made from the NUMERIK with a high
quality audio phono-phono lead. With this lead in place the NUMERIK adopts
‘master’ mode operation and superior audio performance is achieved.
When this lead is not in place the NUMERIK will adopt ‘slave’ mode and will
operate in a conventional manner. If the currently selected input has the
Master Mode (CD Sync) link connected, Master Mode will be selected.
In case of difficulty when setting up the NUMERIK, indicator lights are
provided on the rear panel. See the SET-UP section for details.
14
GENERAL SYSTEM INSTALLATION
KARIK AND NUMERIK The KARIK and NUMERIK should be positioned on a
level surface. Extensive internal screening in the KAIRN preamp, KREMLIN
tuner, KARIK and NUMERIK facilitates stacking the products one on top of the
other without interference, if desired.
POWER SUPPLIES Take care not to position too close to signal leads,
turntables or pre-amplifier.
AMPLIFIERS Pre and power amplifiers may hum if positioned too close
together. For minimum hum experiment by moving the components with the
system at full volume but not playing music (although it is best to turn the
volume down whilst actually moving the components).
LOUDSPEAKERS Loudspeakers should be positioned correctly. They should
be mounted on rigid stands, and not subject to any rocking movement.
CLEAN CONTACTS It is important that the electrical contacts in a hi-fi
system are kept mechanically sound and clean. Occasionally unplugging and
replugging all the connectors will effectively clean contacts.
WARNING This should be carried out after the mains supply has been
switched off.
INTERCONNECT LEADS Correct cables should be used. We recommend
2
good quality copper cable for interconnect leads and advise 4mm multicore
copper cable, such as Linn K20, for speaker leads.
Your Linn dealer can supply high quality interconnects for linking all your hi-fi
components.
15
PROGRAMMING THE KARIK
The KARIK can be programmed from the remote control to play a selection of
tracks.
TO PLAY A SELECTION OF TRACKS make sure the disc is loaded but not
playing. You can tell that this is the case if the
indicator is not lit and
2
the display is showing the number of tracks on the disc. (If you have just put
the disc in, allow the KARIK the few seconds necessary to read and display
the number of tracks). Press and hold the button marked DISPLAY for about
2 seconds until the display shows
P - - A
which indicates that programming mode A has been entered. (If the display
shows “P--b” you’ve held DISPLAY too long. Press OPEN twice, and start
again). Release DISPLAY and the display will show
P 00
which indicates that the KARIK is ready for you to enter your selection.
Use SKIP i or u SKIP to enter a track number, or press the appropriate
digits on the remote control. Press DISPLAY again to enter this track as your
selection. The display will show
P 01
indicating that your first selection has been accepted. Enter further track
numbers the same way, pressing DISPLAY to store each track in sequence.
You can enter up to 20 tracks.
The display will show P 02, P 03 ... and so on as each track is programmed in.
TO FINISH THE PROGRAM Press STOP o. The display will show the total
number of tracks you have entered.
TO CHECK OR ADD TO THE PROGRAM after you have pressed STOP o,
press SKIP i and the first track in the program will be shown. Pressing
SKIP i again will display the second track, and so on. The display shows the
track number, followed by its position in the program. So, “703” signifies that
track 7 is 3rd in the program. If you want to add more tracks, press and hold
.
16
DISPLAY until “P--A” appears. Then release DISPLAY and the display will
show “P” followed by the number of program slots used. Enter the additional
tracks using SKIP and DISPLAY as described previously. Press STOP o when
you have finished adding tracks.
TO PLAY THE SELECTION YOU HAVE MADE press PLAY
.
2
TO PREPARE TO PLAY THE SELECTION YOU HAVE MADE press
PAUSE p. This is useful when you are making a tape. When you are ready to
listen or record, press PAUSE p again or PLAY to start your selection.
2
TO ADD MORE TRACKS TO THE PROGRAM after it is playing press
STOP o. You can now check or add to the program as described above.
TO CANCEL THE PROGRAM press OPEN. The program is now cleared.
TO OMIT A SET OF TRACKS make sure the disc is loaded but not playing.
Press and hold the button marked DISPLAY for about 4 seconds until the
display shows
P - - b
which indicates that programming mode b has been entered. Release
DISPLAY, and the display will show
P-00
indicating that the KARIK is ready for you to enter to your selection. Enter
tracks in the same way as for programming mode A. When you now play the
disc the tracks you have entered will not be played.
NOTES ON PROGRAM MODE While the KARIK is playing a stored program
the A-B REPEAT function is disabled and SKIP i or u SKIP will skip to the
next or previous track in the programmed sequence. SEARCH y will search
through the current track, and then into the next track in numerical, rather
than program, sequence. So, you can use SEARCH y to break out of the
stored program. If you do so though, the program will resume at the end of the
track you used SEARCH y to get into.
17
MAINTENANCE
The KARIK and NUMERIK are designed for long life. To reinforce our
commitment to customer satisfaction and extended product life, we have
included in the design of the KARIK a DIAGNOSTIC OUTPUT CONNECTOR
for ease of maintenance. We recommend that you contact your dealer
approximately two years after purchase, to arrange for a free diagnostic check
on your KARIK.
CLEANING Dust or finger marks can be removed using a soft, slightly damp
cloth. Avoid the use of domestic cleaning fluids.
WARNING Disconnect the mains supply first.
FUSE If the fuse in the mains inlet connector should blow, replace it with the
correct type only. To replace the fuse, first switch off and disconnect the
mains lead. Open the fuse drawer on the mains inlet connector by grasping
either side of the drawer front and pulling outwards. The drawer has two
compartments, the inner one contains the active fuse and the outer one
contains a spare fuse. Remove the blown fuse by poking it out from the under
side of the drawer using a small screwdriver or the end of a pen. Insert the
spare fuse into the inner compartment and close the drawer.
If the new fuse blows then there may be a fault and the complete unit should
be returned to your Linn dealer.
18
GUARANTEE AND SERVICE
This product is guaranteed under the conditions which apply in the country of
purchase.
In addition to any statutory rights the customer may have, we undertake to
replace parts which have failed due to faulty manufacture for a period of time.
To help us, please ask your Linn retailer about the Linn warranty scheme in
operation in your country. In many countries registration of your purchase with
Linn or its distributor will enable you to receive copies of the Linn Record
Newsletter to keep you up to date with developments and products from Linn.
WARNING
Refer all enquiries to authorised Linn retailers only. Unauthorised servicing or
dismantling of the product invalidates the manufacturer’s warranty.
If you are in doubt, please contact your nearest Linn retailer. For information
on your nearest retailer, contact the Linn Helpline in Scotland or your
national distributor.
IMPORTANT
1. Please keep a copy of the sales receipt to establish the purchase date of
the product.
2. Please ensure that your equipment is insured by you during any transit or
shipment for repair.
LINN PRODUCTS LIMITED, FLOORS ROAD, WATERFOOT,
GLASGOW G76 0EP, SCOTLAND.
FREEPHONE (GERMANY): 0130 822156
TELEPHONE: 44-(0) 141-307-7777
FAX: 44-(0) 141-644-4262
EMAIL: [email protected]
19
KARIK SPECIFICATIONS
DIMENSIONS
Width - 320mm Depth - 325mm Height - 80mm
Weight - 5.3kg
TRANSPORT
Linn MEKK 001
FOCUS SYSTEM
Triple Beam Laser Pickup
INPUTS
CD SYNC INPUT
Master/Slave Input Connection
Connector - RCA Phono
Level - 0-10V DC
REMOTE INPUT
Current loop remote control input
Maximum DC current source - 40 mA (short circuit protected)
Sensitivity - 5 mA differential signal current
Bias voltage - 10V (to power remote IR sensor)
OUTPUTS
S/P DIF DIGITAL AUDIO ELECTRICAL OUTPUT
Connector - 75 ohm BNC
Level - 0.5 V pp (75 ohms)
DIAGNOSTIC OUTPUT
Interface to Linn KARIK test equipment
Connector - 9-way D-type
Level - TTL
REMOTE OUTPUT
Current loop remote control output
Connector - RCA Phono
Level - 6mA output signal current
20
NUMERIK SPECIFICATIONS
DIMENSIONS
Width - 320mm Depth - 325mm Height - 80mm
Weight - 4.1kg
CONVERSION TECHNOLOGY
20 BIT 8x oversampling, dual convertor
INPUTS
2 DIGITAL AUDIO S/P-DIF INPUTS
Connector - 75 ohms BNC
Level - 0.2 V to 1 V pp (75 ohms)
Frequency - 44.1 kHz or 48 kHz sample rate 150 ppm
OUTPUTS
2 STEREO AUDIO OUTPUTS
Connector - RCA Phono
Output Level - 2.1V rms (peak code)
Output Impedance - 75 ohms
Minimum Load - 1 kohm
2 CD SYNC OUTPUTS
Master/Slave output connection
Connector - RCA Phono
Control Signal - 0-10V DC
PACK 563
|