OPERATING INSTRUCTIONS FOR THE
SPEEDBREW™ COFFEEMAKER
MODEL: DSP10
R
For better
UNBLEACHED
tasting tea and coffee,
use Mr. Coffee® 8-12 cup basket filters.
Mr. Coffee Replacement
Decanter Model DD10
FOR HOUSEHOLD USE ONLY
FOR QUESTIONS OR SERVICE, CALL
1-800-MR COFFEE
1-800-672-6333 U.S.A.
Monday through Friday,
8:30 am to 5:00 pm Eastern Standard Time
SPECIAL CORD SET INSTRUCTIONS
1. A short power supply cord is provided to reduce the hazards resulting
from becoming entangled in or tripping over a longer cord.
2. An extension cord may be purchased and used if care is exercised in
its use.
3. If an extension cord is used, the marked electrical rating of the exten-
sion cord must be at least 10 amps and 120 volts. The resulting
extended cord must be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children or
tripped over accidentally.
*
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not modify the plug in any way.
If Service Is Required, Do Not Return to Your Store
For Service, call 1-800- MR COFFEE (1-800-672-6333 U.S.A.);
8:30am to 5:00 pm Eastern Standard Time, Monday through Friday
To assist us in serving you, please have the model number
(DSP10) and date of purchase available.
All repairs must be made by an authorized Mr. Coffee Service Center.
Please call us for assistance or for the location of the nearest authorized Mr. Coffee
Service Center. Please do not return this appliance to your store.
We welcome your questions, comments or suggestions.
Please include your complete name, address and telephone number.
Consumer Affairs Department
MR. COFFEE
A Product of Signature Brands, Inc.
Cleveland, OH 44139
3
Introduction
®
Congratulations! You are the owner of a Mr. Coffee SPEEDBREW ™, restaurant style
displacement 10 cup coffeemaker. The SPEEDBREW ™ coffeemaker is faster than
conventional coffeemakers and brews 10 cups of regular coffee in about 3 minutes (after
initial setup). Decaffeinated coffee will take longer. A convenient brew control dial adjusts
water flow so you can brew regular or decaffeinated coffee simply by turning the dial.
Please read all of the instructions in this booklet carefully before you begin to use
this appliance. Proper care and maintenance will ensure the long life of this appliance
and its trouble-free operation. Save these instructions and refer to them often for clean-
ing and care tips.
Table of Contents
Page
Important Safeguards ..................................................................................................2
Special Cord Set Instructions.......................................................................................3
If Service is Required...................................................................................................3
Introduction ..................................................................................................................4
Diagram of Parts..........................................................................................................4
Important Things You Should Know ............................................................................5
Prepare Your Brewer for Use.......................................................................................6
Brewing Coffee ............................................................................................................7
To Get Hot Water Only ................................................................................................8
Draining Water Reservoir.............................................................................................8
Routine Cleaning/Decanter Cleaning...........................................................................9
Troubleshooting Guide...............................................................................................10
Limited Warranty........................................................................................................11
Diagram of Parts
Regular/
Water Reservoir
Lid
Decaffeinated
Brew Control
Dial
Warmer Plate
Switch
Water
Reservoir
Brew Basket
Shower
Head
10 Cup Decanter
Warmer Plate
Reservoir
Power
Switch
(ON/OFF
Switch)
4
Important Things You Should Know
•
The SPEEDBREW™ coffeemaker is designed to remain plugged in at all times
(except during draining and extended periods of non-use). Brewing begins after
water is poured into the water reservoir.
•
A Reservoir Power Switch (ON/OFF switch) is located on the lower left side to com-
pletely shut off all electrical components when your plans take you away from home
for several days or when your coffeemaker will not be in use for an extended period.
Your SPEEDBREW ™ coffeemaker has safety features which make the daily use of
this switch unnecessary.
•
Whenever the SPEEDBREW ™ Reservoir Power Switch has been turned OFF, or
the unit unplugged, allow the water in the tank to heat to the proper temperature
before using. (This will take approximately 15 minutes after the Reservoir Power
Switch has been turned on).
•
•
Your SPEEDBREW ™ coffeemaker unit has an especially designed water reservoir
to keep the water at the proper temperature. This constant supply of hot water
allows you to brew regular coffee in about 3 minutes.
When a pitcher of cold water is poured into the water reservoir, the cold water enters
the internal tank and pushes out hot water to start the brewing process. This cold
water is then heated to the proper temperature and stored until the next brew cycle is
started. Make sure the decanter is on the warmer plate before water is added.
•
Brewed coffee flows into the decanter where it is kept at serving temperature by the
warmer plate. The warmer plate is controlled by the ON/OFF switch located above
the brew basket. NOTE: The Warmer Plate Switch only controls the decanter
warmer. The warmer plate switch should be turned off when the decanter is empty
or the coffeemaker is not in use. (For the Warmer Plate Switch to operate, the
Reservoir Power Switch must be on.)
•
•
The decanter lid reduces coffee evaporation and heat loss. Always place the lid
on the decanter when brewing coffee.
The two position Regular/Decaffeinated Brew Control Dial is located behind the
water reservoir lid. This allows for proper brewing of regular or decaffeinated coffee.
Decaffeinated coffee takes longer to brew than regular coffee.
•
WARNING: To avoid risk of scalding or other injury, do not move your
SPEEDBREW ™ coffeemaker once you have filled the water reservoir.
5
IMPORTANT
Before Using Your SPEEDBREW™ Coffeemaker the First Time
Wash decanter,decanter lid and removable brewer basket in mild detergent and water.
Rinse each thoroughly.
Prepare Your Coffeemaker Before First Use
NOTE:To avoid the risk of damage to coffeemaker, do
not plug in your SPEEDBREW™ coffeemaker until you
complete these steps.
1.Raise the water reservoir lid. (see Figure 1)
2.Turn the brew control dial to “regular”. Using the provided
pitcher, pour one full pitcher of water into the water reservoir
area on top of the SPEEDBREW ™ coffeemaker. Close
the lid and wait three minutes. (see Figure 2) NOTE: Do
not fill the water reservoir with any liquid other than cold
water (or white household vinegar for cleaning - see
“Routine Cleaning” on page 8)..
Figure 1
3.Place the decanter on the warmer plate. Open the lid. Pour a
second full pitcher of water into the water reservoir. The water
will flow into the internal tank. When the water reservoir is full,
a small amount of water will flow into the decanter. NOTE: To
avoid overfilling the water reservoir, you must wait three
minutes before adding the second pitcher of water.
4. When the flow of water into the decanter stops, empty the
decanter.
5. To flush out the machine for first use, repeat steps 3 and 4
two additional times.
Figure 2
6. Place the empty decanter onto the warmer plate.
7. Now you may plug your SPEEDBREW™ coffeemaker into
a 120V, AC outlet.
8. Press the Reservoir Power Switch located on the lower
left side of the SPEEDBREW ™ coffeemaker to ON. (see
Figure 3) Wait at least fifteen minutes for the water in the
internal tank to reach the ideal brewing temperature. Follow
the “Brewing Coffee” instructions on page 7 to brew a perfect
pot of coffee.
Figure 3
6
Brewing Coffee
1. Slide the brew basket open and insert a Mr. Coffee® 8-12 cup
paper basket filter into the brew basket.
2. Add desired amount of coffee according to the coffee
measurement chart found below. Shake lightly to level coffee.
If decaffeinated coffee is used, then turn the brew control dial
to “Decaffeinated” (see Brew Control Dial – Decaffeinated
Coffee on page 8).
Figure 5
3. Be sure the paper filter is properly centered before sliding the
brew basket into place.
4. Place the decanter on the warmer plate. Turn ON the warmer
plate switch located on the front of the machine. (see
Figure 5). This will keep your coffee warm when it has
finished brewing.
5. Raise the water reservoir lid. Fill the pitcher with cold tap
water. (1 cup equals 5 ounces) Pour the water from the
pitcher into the water reservoir. NOTE: Do not fill the water
reservoir with any liquid other than cold water (or white house-
hold vinegar for cleaning - see “Routinge Cleaning” on page 8).
Figure 6
6. Close the water reservoir lid. Your SPEEDBREW ™
coffeemaker will begin brewing coffee as soon as the water is added. (see Figure 6)
After initial start up, you can brew 10 cups of regular coffee in about 3 minutes.
CAUTION: The SPEEDBREW ™ coffeemaker will begin to brew as soon as
water is added.
7. To insure proper brewing temperature please wait at least 10 minutes before
brewing your next pot of coffee. This will allow the water to heat to proper brewing
temperature. Attempting to brew faster than this may result in cold coffee.
WARNING
To avoid the risk of personal injury or damage to property, be sure that the
brew basket is securely in place and that the decanter is centered under the
brew basket before the brewing begins.
WARNING
BREWED COFFEE AND GROUNDS, BOTH IN THE BREW BASKET AND
DECANTER, ARE VERY HOT. HANDLE WITH CARE TO AVOID SCALDING. IF
THE BREW BASKET OVERFLOWS, OR IF THE BREW BASKET FAILS TO
DRAIN INTO THE DECANTER DURING THE BREW CYCLE, DO NOT OPEN OR
HANDLE THE BASKET. RAISE THE RESERVOIR LID, UNPLUG THE COF-
FEEMAKER, AND WAIT FOR CONTENTS TO COOL BEFORE HANDLING.
SUGGESTED COFFEE MEASUREMENT
For the best results, use drip grind recommended for automatic drip coffeemakers.
TO BREW
REGULAR GROUND COFFEE:
13 tablespoons
10 cups (50 ozs.)
8 cups (40 ozs)
6 cups (30 ozs.)
4 cups (20 ozs.)
11 tablespoons
9 tablespoons
7 tablespoons
* Use more or less coffee to suit your taste.
1 cup = 5 oz. brewed coffee
PLEASE NOTE: Decaffeinated coffee may require additional amounts of coffee.
7
Brew Control Dial - Decaffeinated Coffee
Your Mr. Coffee SPEEDBREW ™ coffeemaker comes with a special feature that allows
you to brew a perfect decanter of decaffeinated coffee. Just turn the brew control dial to
“decaffeinated”. This feature allows for the additional time needed when brewing decaf-
feinated coffee. Please note that only decaffeinated coffee should be used when your
brew control dial is in this position. Caution: To avoid overflowing the brew basket do not
use decaffeinated coffee unless the brew control dial is on the decaffeinated setting.
To Get Hot Water Only
The same steps listed on page 7 under “Brewing Coffee” can be used to obtain hot water.
Keep the brew basket in place and omit the filter and coffee. NOTE: This water is hotter
than the water from your faucet and must be handled with care.
Draining the Water Reservoir
The water reservoir in your Mr. Coffee SPEEDBREW ™ coffeemaker should be emptied
whenever the coffeemaker will be moved, shipped, or stored. Please follow these steps:
1. Turn Reservoir Power Switch OFF, unplug the SPEEDBREW ™ power cord and
allow the hot water to cool in the tank. Place the empty decanter on the warmer
plate. Pour a full pitcher of COLD water
Figure 1
into the water reservoir. Close the lid and
wait for the water to stop flowing from the
brew basket. Empty the decanter and
repeat. This will cool the water in the water
reservoir.
2. Remove the brew basket. Grasp the back
of the SPEEDBREW™ coffeemaker and
tip the unit forward over a sink as far as
possible. Most of the water in the water
reservoir will flow from the shower head.
Continue tipping the coffeemaker until the
flow of water stops. (see figure 1)
8
Routine Cleaning
The decanter and brew basket should be rinsed after each use. NOTE: The decanter,
decanter lid, and brew basket are top-rack dishwasher safe ONLY. The outside of
the coffeemaker, including the area above the brew basket, can be wiped with a damp
cloth. Do not immerse the coffeemaker.
In addition, your coffeemaker must be cleaned when you begin to notice excessive
steaming or the brewing time increases considerably. This condition is caused by a
buildup of lime and mineral deposits from your water. It is recommended that you clean
your coffeemaker once a month. To clean your Mr. Coffee® Speedbrew™ coffeemaker
follow the steps listed below.
1. Place a paper filter into the brew basket.
2. Place the decanter onto the Warmer.
3. Pour one full pitcher of undiluted white household vinegar into the Water
Reservoir. NOTE: Do not use any other cleaning products in your
Speedbrew™ coffeemaker. Hot water will flow into the decanter (Do not turn on
the Warmer Plate Switch. The Reservoir Power Switch should remain ON).
4. Let the unit sit for 2 hours. This will allow the vinegar to break down the lime and
mineral deposits.
5. After 2 hours, empty the decanter and return to warmer plate.
6. Pour a full pitcher of water into the Water Reservoir. (The water/vinegar mixture
will flow into the decanter.)
7. Empty the decanter and repeat Step 5 and 6 an additional six (6) times. This will
ensure that all the vinegar will be flushed out of the internal tank.
8. Remove the paper filter from the brew basket and discard.
9. After cleaning, wait at least 15 minutes before brewing your next pot of coffee.
This will allow the water in the internal tank to heat to the proper brewing temperature.
Decanter Cleaning
Hard water can leave a whitish mineral deposit inside the decanter. Coffee can discolor
these deposits, sometimes leaving a brownish stain inside the decanter. To remove these
stains, follow these simple steps:
1. Use a solution of equal parts white vinegar and hot water.
2. Let solution stand in decanter for about 20 minutes and then discard.
3. Wash and rinse the decanter thoroughly using a soft cloth. Do not use harsh
abrasive cleaners. These may cause scratches which can lead to breakage.
9
Troubleshooting Guide
Mr. Coffee SPEED BREW™ Troubleshooting Guide
Problem
Solution
The brewed coffee is lukewarm
or cold immediately after brew-
ing.
•Make sure that the SPEEDBREW™ coffeemaker
is plugged into an outlet.
•Make sure that the Reservoir Power (ON/OFF)
switch is ON.
•Allow the water inside the coffeemaker proper
time to rise to brewing temperature. Refer to the
“Prepare Your Brewer for First Use” section on
page 6.
You have brewed two decanters
of coffee within ten minutes and
the temperature of the coffee in
the second batch is cold or luke
warm.
•Allow the water inside the SPEEDBREW™
coffeemaker proper time to heat to brewing tem-
perature. Refer to the “Brewing Coffee” section on
page 7.
The brewed coffee is hot imme-
diately after brewing, but
becomes cold in the decanter.
•Make sure the warmer switch is ON.
The SPEEDBREW™ cof-
feemaker does not brew a full
decanter of coffee after a full
decanter of water has been
poured into the reservoir.
•Because of infrequent use, your SPEEDBREW™
coffeemaker may have lost water due to evapora-
tion. Please follow these steps:
- If your SPEEDBREW™ coffeemaker
did brew a partial batch of coffee then
the lost water has already been replen
ished and you should be able to conti-
nue with normal brewing.
- If your SPEEDBREW™ coffeemaker
did not brew any coffee then the lost
water has not yet been fully replenished.
Promptly unplug your SPEEDBREW™
coffeemaker and follow the steps in the
section titled Prepare Your Brewer
Before First Use.
The SPEEDBREW™
•The minimum amount of coffee that your SPEED-
BREW™ coffeemaker is designed to brew is 20
ounces (FOUR, 5 oz. cups). When brewing a
partial batch of coffee, pour no less than 20 ounces
of water into the reservoir.
coffeemaker does not brew any
coffee when you attempt to
brew less than a full decanter
of coffee
The SPEEDBREW™
coffeemaker requires more than
four minutes to brew regular
coffee.
•Set your brew control dial to “Regular”.
•Your SPEEDBREW™ coffeemaker may require
cleaning. Refer to “Routine Cleaning” section on
page 8
The brew basket of the
•Set your brew control dial to “Decaffeinated”.
This will lengthen the brew cycle and should
prevent overflow.
SPEEDBREW™ coffeemaker
overflows when you brew with
decaffeinated coffee.
10
Notes
Limited Warranty
Mr. Coffee warrants to the purchaser that the DSP10
coffeemaker by Mr. Coffee® (except for cord set and glass parts)
is free from manufacturer’s defects in material and workmanship
for a period of three years from the date of original purchase when
used in compliance with directions as outlined in the manufactur-
er's instructions, which will constitute reasonable and necessary
maintenance by the purchaser.
In case of manufacturer defects in material or workmanship,
Mr. Coffee agrees to repair (remedy) a defective coffeemaker
without charge. The purchaser's exclusive remedy against Mr.
Coffee shall be for the repair or replacement of a defective Mr.
Coffee product.
All repairs must be made at an authorized Mr. Coffee Service
Center. To locate a Mr. Coffee Service Center, call 1-800-MR
COFFEE (1-800-672-6333). Mr. Coffee shall not be responsible
for any repairs performed at any facility which is not an authorized
Mr. Coffee Service Center.
This warranty gives you specific legal rights, and you may have
other rights which vary from state to state. Any implied warranty
is limited in duration to the three years provided in this, the only,
expressed warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not
apply to you.
In no event shall Mr. Coffee be responsible for incidental or
consequential damages, nor damage due to misuse or the use
of any unauthorized attachment; nor damage caused by use of an
electrical circuit not specified on the Mr. Coffee product. Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may
not apply to you.
A Product of Signature Brands
Cleveland, Ohio 44146-1399
FORM 7070
PRINTED IN CHINA
5/98
|