American DJ DJ Equipment Light Station User Manual

Introduction: Thank you for purchasing the Light Station™  
DMX controller from American DJ®. To optimize the performance  
of this product, please read these operating instructions carefully to  
familiarize yourself with the basic operations of this unit.The Ameri-  
can DJ® Light Station™ is a unique, 16 channel programmable DMX  
controller with MIDI capabilities. This unit features 60 programs, 30  
built in programs and 30 that you can create yourself. This unit also  
comes with a memory back up battery to save and retain your data.  
This unit has been tested at the factory before being shipped to you,  
there is no assembly required.  
American DJ  
®
Customer Support:  
American DJ provides a toll free customer support line, to provide  
set up help and to answer any question should you encounter prob-  
lems during your set up or initial operation. You may also visit us on  
Service Hours are Monday through Friday 10:00 a.m. to 5:00 p.m.  
Pacific Time.  
Voice:  
Fax:  
E-mail:  
(800) 322-6337  
(323) 582-2610  
LIGHT STATION  
User Instructions  
Warning! To prevent or reduce the risk of electrical shock or fire,  
do not expose this unit to rain or moisture. Clearing memory often  
may cause damage to the memory chip, be careful not to re initial-  
ize your unit frequency often to avoid this risk. Only use the recom-  
mended AC/DC power adaptor.  
Caution! There are no user serviceable parts inside this unit. Do  
not attempt any repairs yourself, doing so will void your manufac-  
tures warranty. In the unlikely event your unit may require service,  
please contact your nearest American DJ dealer.  
American DJ Supply  
4295 Charter Street  
Los Angeles Ca 90058  
(323) 582-2650  
Conformity: This product complies to EN 50081-1/EN 55022  
pr EN 55103-1 (EMC emission) and EN 50082-1/EN 61000-4-2 pr  
EN 55103-2 (EMC immunity).  
(323) 582-2610  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 2  
 
chase patterns steps, from one to the next. This CROSS FUNC-  
TION will only operate with the fader channel (1-8).  
as long you hold down the button. Releasing the button will switch  
the fixtures off.  
2. When used in conjunction with the ADD/KILL (17) feature, these  
buttons are used to activate stored channel assignments.You  
may group a number of channels to be activated at once, then  
store this group in one of 16 FLASH BUTTONS (1 & 13).  
3. When the BLIND feature is enabled in chase mode, pressing the  
SHIFT BUTTON (16) along with a channel FLASH BUTTON will  
BLIND (black out) that channel.  
5. A & B Indicators: These LED’s are used to indicate two steps cross  
fading into each other during Cross Mode.  
6. LCD Display: This high quality seven (7) segment LCD display  
is used to display the present operating mode and parameters of the  
running function.  
7. Fade Time Fader: This slider is used to fade steps in Chase Mode.  
Fade time may be adjusted from 0.1 seconds to 5 minutes. Fade  
Time is the amount of time it take the chase program to fade from  
one step to the next. A fade time of 1/10 of a second would be  
almost instantaneous. A fade time of 30 seconds would take 30  
seconds for one step to slowly fade out and advance to the next.  
14.Channel Indicators (9-16): These green LEDs will glow indicating  
channel activity for channels 9-16.  
15.Cross Button: This button is used to activate and deactivate Cross  
Mode. Cross Mode’s activity is indicated by the Cross On and Cross  
off LED indicators.  
8. Level Fader: This slider acts as a master output level for the  
patterns when running in Chase Mode.  
16.Shift Button: This button is used in conjunction various other button  
to access different functions.  
9. Dimmer Speed Fader: This slider controls the chase speed for  
Channel Sliders 1-8. Chase speed can be adjusted from eight (8)  
steps per second to one step per minute.  
17.Add/Kill Button: This button is used to toggle through the ADD and  
KILL functions. When in KILL mode, the yellow LED will glow.  
18.Pattern Up/Button Setup Button: This button will serve two  
functions:  
10.Switch Speed Fader: This slider controls the chase speed for  
switched channels 9-16. Chase speed can be adjusted from one  
step every 30 seconds to one step every 10 minutes.  
1. In chase or program mode, this button is used to select the next  
pattern or chase. The current pattern will be displayed in the  
LCD display (6). Holding down this button will quickly advance  
through the patterns. Tapping this button will increase the pattern  
by one.  
11.Audio Fader: This unit can be set to run the chase programs to  
sound. This slider adjusts the sensitivity of the internal microphone.  
12.Latch Buttons (Channels 9-16): These button serve two functions.  
The Latch Buttons levels are independent from Fade Time.  
When operating in Assign Mode, these button will control any  
channels linked by the Assign Function.  
2. When used with the SHIFT BUTTON (16), this button will select  
between Channel Flash and Assign Add/Kill modes.  
19. Pattern Down/Fade Time Setup Button: This button will serve  
two (2) functions:  
1. In Manual Mode, they are used as ON/Off buttons for any  
fixtures connect to channels 9-16.  
2. In program mode, these buttons are used to trigger the various  
1. In chase or program mode this button is used to decrease the  
selected pattern or chase. The current pattern is displayed in the  
LCD display (6). Holding down this button will quickly decrease  
the patterns, tapping this button will decrease the pattern by one.  
2. When used with the SHIFT BUTTON (16) this button will enable  
or disable the Fade Time function. The current Fade Time function  
is noted by LED indicators above the this button.  
programs that may have be assigned to these channels.  
13.Flash Buttons (channels 9-16): These button will serve three  
functions:  
1. In manual mode these buttons will momentarily activate any  
fixtures assigned to those channels. These fixtures will remain on  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 5  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 6  
 
BUTTON (16), is used to delete a program (CHASE) pattern.  
20.Step Up/Cross Setup Button: This has two functions:  
1. In manual chase or program modes, this button is used to  
select the next step, (scene) in the pattern. The current step  
will be displayed by the right two digits in the LCD display (6).  
Holding down this button will quickly advance through the steps  
(scenes). Tapping this button will increase the pattern by one.  
2. When used with the SHIFT BUTTON (16) this button is used to  
activate or disengage the CROSS FUNCTION.  
26.Tap Sync/Manual Step Button: This button has two functions:  
1. In CHASE MODE, this button is used to set a momentary speed.  
Channels 1-8 will then chase to this beat.  
2. When used with the SHIFT BUTTON (16), this button is used to  
activate the MANUAL STEP MODE. This mode allows you to  
manually select chases and control steps for channels 1-8.  
27.Patch/Midi Channel Button: This button is used to activate the  
PATCH FUNCTION or to set the MIDI channel:  
21.Step Down/Blind Button:This has two functions:  
1. In manual chase or program modes this button is used to  
select the previous step (scene) in the pattern. The current step  
will be displayed by the right two digits in the LCD display (6).  
Holding down this button will quickly scroll backward through the  
selected chase steps (scenes). Tapping this button will decrease  
the pattern by one.  
1. To activate the PATCH function, hold down this button for two  
seconds. The red PATCH LED will glow indicating PATCH is  
ready to be set or changed.  
2. To activate the MIDI channel adjustment settings, press and hold  
down the PATCH/MIDI CHANNEL BUTTON for two seconds  
while holding down the SHIFT BUTTON (16).  
2. When used with the SHIFT BUTTON (16) during CHASE MODE,  
this button will engage or disengage the BLIND FUNCTION.  
28.Stand By/Manual Button: This button is used to select Stand By  
and Manual functions:  
22.Loop/Loop Exit Button: This button serves two functions:  
1. This button is used to activate and set chase programs into  
LOOP MODE.  
1. When the unit is powered on, it will always default to Stand By  
mode (no output). Pressing this button will take you in and out  
of Stand By mode.  
2. Hold down the SHIFT BUTTON (16) while pressing this button to  
enter MANUAL OPERATION MODE.  
2. Used with the SHIFT BUTTON (16), this operation will disengage  
and clear LOOP MODE.  
23.Program/End Step Button: This button has three functions:  
1. This button is used to engage PROGRAM MODE.  
2. When in PROGRAM MODE, this button is used to load a scene  
into a chase pattern.  
29.Full On Button: Pressing this button will bring FADER CHANNELS  
1-8 (3) to full output.  
Function and Controls - Rear Panel  
3. When used with the SHIFT BUTTON (16), this button is used to  
finalize a program.  
3 0 3 1 3 2 3 3  
3 4 3 5 3 6  
3 7  
LINE INPUT  
100 mV-1Vpp  
24.Chase/Audio Button: This button has two (2) functions:  
1. This button is used to enter CHASE MODE.  
2. Used with the SHIFT BUTTON (16), this button will activate  
AUDIO MODE.  
DC INPUT  
DC 12V-20V,  
250mA min.  
Polarity Select  
+
-
1-Ground  
2-Data-  
1-Ground  
2-Data-  
POWER  
DMX OUT  
MIDI THRU  
MIDI IN  
FOOT CONTROL  
3-Data+  
3-Data+  
30.Power Input: Connect the included external power supply to this  
connection. Be sure to only a recommened power supply DC 12v-  
20v, 250mA min.  
25.Assign/Delete Program Button: This button serves two functions:  
1. This button activates the ASSIGN function. This functions allows  
you to ASSIGN a group of channels to a single FLASH BUTTON  
(1 & 13).  
31.Power Switch: This switch connects and disconnects main power.  
32.DMX Polarity Switch: This switch changes the DMX line polarity to  
2. In PROGRAM MODE, this button, when used with the SHIFT  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 7  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 8  
 
accomidate the use of some older European fixtures.  
4.Once you have selected a CHASE bank, you may begin to adjust  
the channels (1-16) to your liking.  
33.DMX XLR Output: A maximum of 96 DMX channel output. This is  
the DMX signal output. This is a 3 pin XLR connector. If connecting to  
a 5 pin XLR input connector you must use a 3-5 pin adaptor.  
5.Once you have adjusted the channels to your desired settings press  
the PROGRAM BUTTON (23) once to record your scene into  
memory. When you press the PROGRAM BUTTON (23), all the  
channel LED’s will flash indicating the scene has been stored into  
memory. The right two digits in the LCD DISPLAY (6) will advance  
to the next available step.  
6.You may continue this pattern up to 99 times per each CHASE  
PATTERN.You may mix and match the top and bottom channel  
buttons together in a CHASE PATTERN, however, remember that  
the upper and lower channels chase speeds are controlled  
separately.  
7.When you have completed programming all your steps you must  
record an “End Step” to finalize your CHASE PATTERN. To  
program the “End Step,press and hold down the SHIFT BUTTON  
(16). While holding down the SHIFT BUTTON (16), press and  
release the PROGRAM BUTTON (23).You will see all the LEDs  
flash indicating the “End Step” was successfully programmed.  
8. To exit the program mode, press and hold the PROGRAM  
BUTTON for two (2) seconds.  
34.Midi Thru: This connection is used to connect the incoming MIDI  
signal to another MIDI device.  
35.Midi In: This connection is used to connect a MIDI triggering device,  
such as a keyboard or drum machine.  
36.Audio Line Input: Signal input range from 100mV to 1Vpp. This is an  
audio line input. Connect a mixer or other audio device to trigger this  
unit to sound. When an audio signal is connected it will automatically  
disconnect the unit’s internal microphone.  
37.Foot Control Input: This connection is for the optional external Foot  
Controller.  
Foot Controller Pin Configuration:  
1.  
2.  
3.  
4.  
5.  
Step Up  
Pattern Up  
Stand By  
Full On  
Running Chase Patterns: This function allows you to automati-  
cally run one of the 60 CHASE PATTERNS. The speed of these chase’s  
can be controlled by the DIMMER SPEED (9) and SWITCH SPEED (10)  
faders. The DIMMER SPEED (9) will control channels 1-8 and SWITCH  
SPEED will control channels 9-16. To run a chase pattern:  
1.Press the CHASE BUTTON (24). The chase LED in the LCD Display  
(6) will light indicating you are in CHASE MODE.  
Common  
Operating Instructions  
Programming Scenes (Steps) into Chase Patterns: This  
function allows you to turn on specific channels (1-16) at one time to  
be programmed into a Chase. This controller stores 60 CHASE PAT-  
TERNS, 1-30 are user programmable and 31-60 are preset and cannot be  
changed. You may program SCENES into CHASE PATTERNS 1-30 only.  
To program a scene:  
2.Use the PATTERN BUTTONS (18 & 19) to select the CHASE PAT-  
TERN you wish to run.  
3.Use the SPEED CONTROLS (9 & 10) to adjust your chase speed  
and the LEVEL CONTROL (8) to set your output intensity.  
1.Press and hold down the PROGRAM BUTTON (23) for two  
seconds. The green program LED will turn on indicating you are in  
program mode.  
2.At this point the display should read 01:01.The first two digits display  
the CHASE bank and the second pair of digits displays the SCENE  
bank.  
Using the Built In Programs: This controller comes with 30  
preset programs.These programs are designed to get you up and running  
in minutes. Programs 31-40 control channels 1-8, 41-50 control channels  
9-16, and programs 51-60 combine channels 1-16. Chase Pattern 40 is a  
combination of 31-39. Chase Pattern 50 is a combination of 41-49. Chase  
Pattern 60 is a combination of 51-59. These chases can not be changed  
or edited.  
3.Use these PATTERN BUTTONS (18 & 19) to select a CHASE bank  
to store the scenes you are about to create.  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 9  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 10  
 
1.Run a chase in a normal fashion.  
2.Bring the DIMMER SPEED SLIDER (9) down until “SHO” appears  
in the LCD DISPLAY (6).  
3.When “SHO” appears you may use the STEP UP and DOWN  
BUTTONS (20 &21) to manually step through a CHASE PATTERNS.  
4.In this function you may change your selected CHASE PATTERN  
at any time.  
Cross Mode: Cross mode is a manual adjustment that fades from one  
step to the next.You may use this function in any CHASE PATTERN.This  
function will not effect channels 9-16. To use this function:  
1.Be sure you are in CHASE MODE.  
2.Turn CROSS MODE on by holding down the SHIFT BUTTON (16),  
and pressing the CROSS SETUP BUTTON (20) until the yellow  
CROSS ON LED glows.  
3.Press the CROSS BUTTON (15) to activate the cross function.  
Channels 1-8 will stop chasing and the MASTER FADER (4) LED  
will turn off. Either the “A” or “B” LED on the MASTER FADER  
(4) will begin to glow depending on the position of the fader.  
4.You may now use the MASTER FADER (4) to manually cross fade  
through a CHASE PATTERN’s steps. Sliding the MASTER FADER  
(4) up and down will change the steps from one to the next. The  
slower you move the fader the slower the scenes will fade from one  
to the next.  
Deleting Chases: This function allows you to delete an unwanted  
CHASE PATTERN. Please note that only CHASE PATTERNS 1-30 can be  
deleted, 31-60 are built in programs and can not be deleted or changed in  
any way. Also note that a program is never completely erased unless you  
initialize the controller.The program will simply not be able to be executed.  
It can always be recalled later. To delete a CHASE PATTERN:  
1.Enter PROGRAM MODE as described in “Programming Scenes”  
on page 9.  
2.Use the PATTERN BUTTONS (18&19) to select the pattern you wish  
to delete.  
3.When you reach the program you wish to delete, press the DELETE  
PROGRAM BUTTON (25) while holding down the SHIFT BUTTON  
(16). All the channel LED’s will flash indicating the command  
registered.  
5.In this operation, the FADE TIME (7) level will function.  
6.You may use the CHASE PATTERN BUTTONS (18 & 19) to select a  
different chase at any time.  
Loop Mode: This function allows you to group several CHASES  
together and run them in a sequential repeating pattern.  
1.Be sure you are in CHASE MODE.  
4.To exit this function press the CHASE BUTTON (24).  
2.Go to the first pattern you wish to program into the loop and press  
the LOOP BUTTON (22). After you press the LOOP BUTTON (22),  
the channel green LEDs will flash and “LP” will be displayed in  
the right two (2) digits in the LCD DISPLAY (6).  
3.Repeat step two until you have enter all your desired CHASE  
PATTERNS. If the LOOP BUTTON (22) is not pressed within 10  
seconds, the loop will automatically start to cycle.You may add the  
same CHASE PATTERN more than once.  
4.When you have finished entering all you chases, wait 10  
seconds and “CLwill appear in the right two digits of the LCD  
DISPLAY (6). When this happens the chases will automatically  
begin to run and loop in the same pattern you programmed them in.  
5.To cancel or exit this mode, press the LOOP EXIT BUTTON  
(22) while holding down the SHIFT BUTTON (16).  
Assign Add/Kill:This function allows you to override a chase and turn  
a single or a group of channels on. Channels are assigned to the FLASH  
BUTTON (1 & 13), allowing to have a total of 16 programmed overrides.  
You may use your overrides at different times and may use more than one  
at a time.You can set this function to blackout (“KILL) the chase, so only  
your override channels come on.You may also, set this function to “ADD”  
to the chase. When you “ADD,” your override channels will come on as  
your chase is running. This function will operate in any chase. This will  
be a momentarily function and your chase return to normal as soon as  
release the FLASH BUTTON (1 & 13).  
To program in an override:  
1.Hold down the ASSIGN BUTTON (25) for two seconds until the  
red assign LED come on and “AS” is displayed in the LCD  
Display (6).  
2.While holding down the SHIFT BUTTON (16), use the PATTERN UP  
BUTTON (18) to selected “ASSIGN ADD.ASSIGN ADD will be  
indicated by a red LED above the PATTERN UP BUTTON (18).  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 12  
Show Mode: This function gives you manual control over channels  
1-8 when running in normal chase mode. This function will not effect  
channels 9-16 in any way. To operate in show mode:  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 11  
 
3.Turn on any channels you wish to assign to a FLASH BANK.  
4.After you have turned on your desired channels, press on of the  
FLASH BUTTONS (1 &13) while holding down the ASSIGN  
BUTTON (25). ALL the channel LED will flash indicating that your  
program was placed into that FLASH BUTTON’s memory.  
once. For example, say you have a 4 channel DMX pack with 5 amps  
maximum load per a channel and you want to turn on four 500 watt  
lamps on DMX channel one. Your DMX pack is automatically going to  
assign one 4 DMX channels to your pack one for one. To reduce the  
risk of constantly blowing your pack you can plug each lamp into all  
four (4) of your packs channels. Then you can patch these channels  
to be triggered all at once. Since each of the 16 channels of the Light  
Station™ represent a DMX channel you would only have 16 to work  
with. However, if you patch your DMX channels, you could have a  
maximum of six DMX channels triggered per a channel on the controller.  
So, you could tell your controller to trigger DMX channels 1-4 by slider  
1 on the board. This would then activate all four channels on your  
DMX pack, allowing all four lamps to be turned on at once, therefore  
eliminating the possibility of blowing you pack channels due to excessive  
load per a channel, because now your lamps are spread out through  
your pack. To patch channels:  
Recalling an ASSIGN PATTERN:  
1.You may recall your assign pattern in any chase function.  
2.To add to the chase be sure the yellow LED next to the ADD/KILL  
(17) is off and the red ASSIGN ADD LED is on. Simply press the  
FLASH BUTTON (1 & 13) that stores the scene you wish to recall.  
You’ll notice that the chase remains running and your scene turns  
on.You may recall (ADD) several scenes at once, by pressing as  
many FLASH BUTTON (1 & 13) as you like at one time.  
3.To blackout (KILL) the chase and just turn on your programmed  
scene, press the ADD/KILL BUTTON (17) to turn on the yellow LED.  
Be sure you are in ASSIGN KILL mode. Press the FLASH BUTTON  
(1 & 13) that store the scene you wish to recall.You’ll notice that the  
chase stops and your scene comes on.  
1.Press and hold down the PATCH BUTTON (27) until the red  
indicator LED turns on.  
2.The LCD DISPLAY (6) will read “01:01.The left two digits  
represent the controllers 16 channels (1-8 faders and 9-16 Latch  
Buttons). The right two digits represent the 96 available DMX  
channels.  
4. For both “ADD” and “KILLthe scene will remain on as long as  
hold the FLASH BUTTON (1 & 13) down. Also you may turn several  
ASSIGNS on at once.  
Blind Function:This functions allow you to blackout (BLIND) specific  
channels from your chase programs.To BLIND a channel be sure you are  
in chase mode and:  
3.Use the STEP up and DOWN BUTTONS (20 & 21) to adjust the  
DMX channels you wish to patch.  
4.Use the PATTERN UP and DOWN BUTTONS (18 & 19) to select  
the controller channel (1-16) you wish to patch the DMX channel  
too.  
1.While holding down the SHIFT BUTTON (16) press and release the  
BLIND BUTTON (21) to activate the blind function.  
2.While holding down the SHIFT BUTTON (16) press and release the  
FLASH BUTTON (1 & 13) that corresponds to channel you wish to  
remove from the chase.  
3.You may repeat this process to blind as may channels as you like.  
4.To remove a channel simply reverse the process, hold down the  
SHIFT BUTTON (16) and press and release the FLASH BUTTON (1  
& 13) that correspond to channel you wish to return to the chase.  
5.To cancel the BLIND FUNCTION hold down the SHIFT BUTTON  
(16), press and release the BLIND BUTTON (21). This will disable  
the blind function.  
5.Be sure to select your DMX channel before you select your  
controller channel to complete this function properly.  
6.After you have completed your adjustments, hold down the PATCH  
BUTTON (27) until the red indicator LED shuts off, to exit this  
function.  
Manual Mode: This function shuts off all other functions and allow  
you to use the controller as a basic on/off dimmer. To activate this mode  
press and release the MANUAL BUTTON (28) while holding down the  
SHIFT BUTTON (16).  
Manual Step Mode:This mode allows you to manually control chan-  
nels 1-8 when in chase mode. This function will only effect channels 1-8,  
channels 9-16 will continue to chase normally. In this function you can  
Patch Settings: This function allows you to overlap DMX channels  
together, giving you up to 96 DMX channels to work with. This function  
is useful if you would like several channels on one DMX pack to turn at  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 13  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 14  
 
also change chase patterns normally. To activate this function press and Caution: This operation may be harmful to the controllers internal Flash  
release the MANUAL STEP (26) while holding down the SHIFT BUTTON Memory, please use this operation infrequently.  
(16). The LCD DISPLAY (6) MANUAL STEP LED will light, indicating  
this function has been activated. To exit this function press the CHASE Options:  
BUTTON (24) at any time.  
An optional foot controller may be purchased separately. This controller  
will allow you to control some of the function by remote. With the foot con-  
troller you may control pattern step up, pattern up, stand by mode, full on.  
Please contact you American DJ dealer for pricing.  
Fade Time Function: This function can be operated in any normal  
chase function. This function allows you to control the amount of time it  
takes for one scene to switch off and the next to turn on. Basically one  
scene fades to the next. The amount of fade time varies from instant to  
10 minutes.This function is controlled by the FADE TIME SLIDER (7) and  
only effects the dimmer channels (1-8). When the FADE SLIDER is set  
to zero the amount of time it takes for one scene to fade to the next will  
be instant, when the fader is set to 10, it will take about 10 minutes to  
fade from one scene to the next. To activate this function move the FADE  
TIME SLIDER (7) up and down during any normal chase function.  
Midi Settings: This controller can be triggered by any type of MIDI  
device.To use the MIDI function, plug in a standard MIDI controller to the  
MIDI input jack (35) on the rear of the Light Station.™ When your unit is  
receiving a MIDI signal the yellow MIDI SIGNAL LED will begin to flash  
rapidly. To operate properly the MIDI input channel must match that of  
the controller MIDI receiving channel. The controller’s default MIDI input  
signal is one, you may find it necessary to change this setting if you are  
running several MIDI devices. To adjust the controllers input MIDI signal  
hold down the MIDI CHANNEL BUTTON (27) for two seconds while hold-  
ing down the SHIFT BUTTON (16). “CH:01” will appear in the LCD DIS-  
PLAY (6). Use the STEP UP and DOWN BUTTONS (20 & 21) to change  
the input if necessary. Below you will find the MIDI NOTE DATA:  
Note Number  
22-81  
82-97  
99  
101  
102  
Velocity  
Master Pattern Level  
Channel Dimmer  
Function  
Turns Patterns 1-60 On & Off  
Identical to the Flash Channels 1-16  
Full ON  
Execute the patterns step by step  
Engages and disengages STAND BY mode  
Please note when use a MIDI controller the LEVEL SLIDER (8) will  
not function.  
Controller Reset and Memory Dump:This board may be reset  
to factory settings at any time. You may use this function to erase all  
your programs. This function may also be used to eliminate any system  
FREEZE.  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 15  
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 16  
 

3D Connexion Two Way Radio 7906 User Manual
Aastra Telecom Telephone 1600IP User Manual
Acer Computer Monitor ADPC1940 User Manual
Adaptec Network Card WirelessTM USB Adapter User Manual
Advantech Personal Computer PPC L128T User Manual
Agilent Technologies Power Supply 6625A User Manual
Air O Swiss Humidifier AOS 7147 User Manual
AMD Computer Hardware GA M51GM S2G User Manual
ATON Stereo Receiver AIR3 User Manual
Avenview TV Cables HDMI C5SP 4 User Manual