American DJ Paper Shredder XDM 241 User Manual

User Instructions  
XDM-241  
“SHREDDER”  
PREAMP MIXER  
Thank you for purchasing this American DJ® product. The XDM-241 is ready to be used,  
there is no assembly required. Please read the following instructions before installing  
or using your new unit. The XDM-241 has a 2 year limited warranty!  
Safety Instructions  
Always plug in the power last. Make sure that the Power switch is set to the OFF position before connecting other devices  
to the mixer.  
Keep this device away from rain and moisture!  
Keep away from heaters and other heating sources!  
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch on the mixer  
immediately. The arising condensation of water might damage your device. Leave the device switched off until it has  
reached room temperature.  
Never put any liquids on the mixer or close to it. Should any liquid enter the device, disconnect from main power  
immediately. Have the device checked by a qualified service technician before operating again. Any damage caused by  
liquid entering the device is not subject to warranty!  
Never let the AC cord come in contact with other cables! Handle the AC cord and all AC connections with particular care.  
Make sure that the available voltage is not higher than stated on the AC voltage selector (12).  
Before the device is switched on, all fader and volume controls should be set to 0 or minimum position.  
Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not  
subject to warranty.  
There are no user serviceable parts inside the mixer. For maintenance and/or service, contact an authorized  
American DJ® dealer.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-241 User Instructions page 1  
 
Functions  
8
1
®
5
MASTER LEVEL  
11  
+5  
+5  
10  
0
0
POWER  
0
10  
MASTER  
-5  
-5  
7
-10  
-15  
-10  
-15  
PHONES  
MIC  
5
5
9
5
2
L
dB  
R
0
10  
0
10  
DJ MIC  
CUE LEVEL  
2
PHONO 1  
LINE 1  
PHONO 2  
LINE 3  
LINE 2  
LINE 4  
6
ch1  
ch2  
CUE  
3
3
PREAMP MIXER  
FEATHER FADER  
ch1  
ch2  
CROSS FADER  
PROformer Series  
4
(1) POWER SWITCH  
(2) LINE/PHONO SWITCH - Used to select the input (LINE or PHONO) to be sent to channel 1 or 2. Can also be used for  
TRANSFORMER SCRATCHING.  
(3) CHANNEL FADER CHANNEL 1 / CHANNEL 2 - Used to adjust the input level of each channel.  
(4) CROSSFADER - Mixes the signals of channel 1 and channel 2. When the crossfader is set in the center position, both  
channels can be heard at once.  
(5) CUE LEVEL CONTROL - Adjusts the headphone output level.  
(6) CUE SWITCH DIAL CHANNEL 1 / CHANNEL 2 - Use the cue switch dial in order to select the channel to be moni-  
tored.  
(7) PHONES JACK - Connect headphones to this jack. Headphones from 8 Ohms to 600 Ohms can be used. 16 Ohms is  
recommended.  
(8) MASTER LEVEL DISPLAY - This display shows the signal level of the master output.  
(9) DJ MIC CONTROL - Adjusts the microphone volume.  
(10) MIC INPUT - 1/4 inch (6.3 mm) jack plug for microphone input to mixer.  
(11) MASTER LEVEL KNOB - Adjusts the level of the master output.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-241 User Instructions page 3  
 
Inputs and Outputs  
18  
LINE 3  
LINE 4  
LINE 3  
LINE 4  
L -  
R -  
17  
AMP  
REC  
LINE 2  
PHONO 2  
LINE 1  
PHONO 1  
OUTPUT  
CH 2  
CH 1  
12  
14  
16  
15  
13  
(12) DC POWER IN  
(13), (14) LINE / PHONO INPUT JACK - Input jacks for CH1 & CH2. Connect turntables equipped with MM  
pickup cartridges to the PHONO input. CD Players or Tape Decks should be connected to the LINE input. Line level  
musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to the LINE  
inputs.  
(15) REC OUT - To record your record unit. The REC OUT level is not influenced by the master control.  
(16) AMP OUTPUT - Parallel output for P.A. output. Connect with the input of power amplifier.  
(17) GND (Ground Terminal) - Connect this terminal to ground lead of the turntable. This helps to reduce humming and  
popping noises.  
(18) LINE/PHONO SELECTOR - Used to switch the channel input jacks to line or phono.  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-241 User Instructions page 4  
 
Replacing the Crossfader  
Instructions for replacing the crossfader:  
• Disconnect from main power supply  
• Remove the fader knob.  
• Remove the two outer screws.  
Take the fader out and unplug the connection cable.  
• Connect the new fader and replace back into mixer.  
IMPORTANT! • Only replace cross fader with American DJ® high quality  
Feather Fader™ (FF-1).  
Technical Specifications - model XDM-241  
Inputs:  
Microphone  
Phono  
1.5mV, 600 Ohm  
3mV, 47kOhm  
Line  
Output  
Frequency range  
Distortion  
S/N-ratio  
150mV, 27kOhm  
7V, peak to peak  
20Hz-20KHz, ± 2dB  
<0.08%  
>70dB  
Tone control  
Treble: 10Khz ± 12dB  
Bass: 100 Hz ± 12dB  
16 Ohms  
DC 12V 500mA  
6.5” W x 8.75” D x 3.75” H  
211 x 114 x 285 mm  
3.5 lbs. / 1.5 kg  
Headphone impedance  
Power supply  
Dimensions  
Weight  
© American DJ® AUDIO Los Angeles, CA 90058 USA  
Specifications subject to change without notice. XDM-241 User Instructions page 5  
 

3Com Switch WX3000 User Manual
Abocom Network Router UA600GS User Manual
AEG Food Processor KM 21 User Manual
ALK Technologies GPS Receiver Symbian S60 User Manual
Alpine Car Stereo System IVA D100 User Manual
American Dryer Corp Clothes Dryer ADG 215 User Manual
American Standard Indoor Furnishings 0293 Series User Manual
AO Smith Water Heater ADM 115 User Manual
Avenview TV Cables HDM C5 3X SET User Manual
Axis Communications Security Camera M1103 User Manual