Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #: 8207BCC
DELUXE TREND NURSERY CENTER
Instruction Manual
Convenience through Innovation and thoughtful design
05.07
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
TO ASSEMBLE PLAYARD
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA
CONTENTS (Fig. 1-1):
1 Playard
1 Mattress
1 Organizer
2 Leg extensions (1 Left,1 Right)
2 Leg extensions (1 Left, 1 Right) with Wheels,
and hardware
Figure 1-1.
1 Travel or Storage bag
BEFORE YOU BEGIN: The Baby Trend Playard is designed so that,
when properly setup, the fabric of the playard places pressure on the 4
top rails making them nearly impossible to unlock. This safety feature
is activated when you push down on the playard floor to lock the bottom
rails. When setting up the playard, if you allow the bottom rails to lock
before locking the top rails, the fabric pressure will not allow you to lock
the top rails. Please see (Fig. 7.) for the proper position of the bottom of the
playard when locking the top rails. Always keep fingers away from corners
when setting playard up.
Figure 1.
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 Velcro straps
and set mattress aside (Fig. 2).
Figure 2.
2. Turn the playard upside down. (Fig. 3). Push each leg extension into the
bottom of the leg until both sides of extension snap into place. (Fig. 4).
Check that the extension is firmly connected. Attach the wheels to the
playard with the axle and nut as shown in figure (Fig. 5). The brake cluster
on the wheel must face to the inside. The axle is inserted from the outside
to the inside. (Fig. 6). Check that the wheels are firmly connected.
3. Stand Playard on legs keeping feet of playard close together as shown in
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.
Leg extensions
* READ IMPORTANT: In order to continue, the handle in the center
of the floor of the Playard MUST remain raised in order for the
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard
should almost touch each other. All 4 bottom rails must be pointed
upward in order to LOCK top rails.
4. Push down on center of Playard floor until it is flat and locks into
position (Fig. 8). The center lock mechanism will lock automatically.
The center lock will rotate clockwise about 90 degrees as it locks.
Wheels
NOTE: Test rails to make sure they are locked. Push down on each
rail making sure they are rigid and in a set position.
Figure 3
3
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
WARNING: All top rails MUST be
straight and locked in position or child may
become entrapped and suffocate.
See figure 9 and 10.
5. Place mattress in Playard with padded side up (Fig. 11).
Figure 4
Right
Left
NOTE: DO NOT insert mattress if using bassinet feature. Go to
bassinet instructions.
6. Feed the 3 hook and loop straps (found underneath the mattress),
through the slots on the bottom of the sides of the Playard. Fasten
the hook and loop straps to the underside of Playard to prevent the
mattress from moving (Fig. 12) (Fig. 13).
Insert
axle from
outside
Insert
axle from
outside
WARNING: To prevent child from
becoming entrapped under the mattress pad
and suffocating, hook and loop straps MUST
Left
Figure 5
Right
be secured to underside of Playard.
7. The organizer can attach to any side of the playard. Insert the plastic
hooks into the organizer as shown in (Fig 14 ). For best results, attach
the organizer on the long side of the playard.
Outside
Inside
8. Attach the organizer, by pushing the plastic clips down over the top
rail. (Fig. 14 A). The maximum weight capacity of the organizer
is 3 pounds.
Figure 6
9. To operate the brakes on the wheels, press downward on the brake
lever as shown in figure 15. To release, lift upward on the lever.
Figure 7
Assembly is now complete and playard is ready to use.
Figure 8
Figure 10
Figure 9
Figure 11
Figure 13
Figure 14
Figure 14A
Figure 15
Figure 12
4
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
FOLDING PLAYARD
1. Undo the 3 hook and loop straps holding mattress from underneath
Playard floor. (If mattress is not used in the bassinet). Remove mattress
and set aside.
2. Grasp the center floor lock handle pushing down. Rotate the handle
counter-clockwise about 90 degrees and lift upward until handle is as
high as the top rails. Gather the four feet of the playard together so that
they nearly touch each other. See figures 1 and 2.
Rotate before
lifting
Figure 1
NOTE: TOP RAILS OF THE PLAYARD ARE STILL IN THE
“LOCKED” POSITION.
3. Locate release button on the center of the bottom of each top rail. Lift
slightly while squeezing button until the rail clicks. Push down on rail
(while still holding release button in) until side forms a “U”. Repeat for
remaining sides (Fig. 3).
NOTE: If top rail(s) do not form the “U” completely do not force. Check
the floor of your Playard to make sure all bottom rails are unlocked and
pull up on middle handle of floor again. Repeat step 3.
Figure 2
4. Pull up on handle in center of Playard (Fig. 4). Gather legs of
Playard together.
5. Wrap mattress around Playard frame with padded side facing in.
6. Secure the 3 hook and loop straps by feeding through loops on end of
mattress and folding back onto itself (Fig. 5).
7. Place Playard in carry bag so handle comes through opening
between zippers.
Figure 3
WARNING: NEVER LEAVE INFANT IN
PRODUCTWITH SIDES DOWN. Infant may
roll into space between pad and loose mesh
side causing suffocation.
Figure 5
Figure 4
5
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
PLAY YARD BASSINET / CHANGING AREA
WARNING:FAILURE TO FOLLOW THESE WARNINGS AND THE
ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless
otherwise advised by your physician.
• Always provide the supervision necessary for the continued safety of your child. When used for playing,
never leave child unattended.
• Adult supervision is always necessary when using your bassinet.
• Your playard, including side rails and bottom pad, must be fully erected prior to use.
• Top rails must be locked.
• Bottom rails must be in flat, locked position.
• SUFFOCATION HAZARD: To help prevent suffocation from entrapment, use only the mattress provided
®
by Baby Trend . Never use additional mattress or padding. Never use plastic shipping bags or other plastic
film as mattress covers not sold and intended for that purpose. Avoid SUFFOCATION HAZARD caused by
a loose sheet. A fitted sheet is recommended. The fitted sheet must fit the mattress tightly.
• STRANGULATION HAZARD: DO NOT place items with a string around child’s neck, such as hood
strings or pacifier cords. DO NOT suspend string over bassinet or attach strings to toys.
• DO NOT add padding or other objects inside your bassinet which will permit a child to climb out.
• To prevent your child from falling out of the bassinet discontinue using your bassinet when
your child is too active, able to climb out, weighs over 15 lbs.. (6.8 kgs.), or is over 4 months old.
• Use changer with infant who’s weight is less than 18 lbs (8.2 kg ) and is less than 25 inches (63.5 cm) tall.
• Discontinue use of changer if infant can push up on hands and knees or sit unassisted.
• DO NOT use a water mattress with this bassinet.
• Use your bassinet with only one child at a time.
• Keep bassinet away from stoves, heaters, campfires and other hazards.
• Never place a child under the bassinet.
• Never leave changer on top of playard with a child in the playard. Always flip changer to the outside
when not in use.
• DO NOT store the bassinet in the playard.
• The bassinet must be fully assembled and installed, including top rails and bottom pad, before using.
• Before each use or assembly, inspect the playard and bassinet / changing area for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use playard or bassinet if any parts are missing or
broken. Call our Customer Service department at 1-800-328-7363 for replacement parts.
• To protect your child from falls and other injuries: always use safety belt when child is on the changing
table, always stay within arm’s reach of your child when using the changing table, never leave child
unattended.
Baby Trend, Inc.
1567 S. Campus Ave.
Ontario, CA 91761, U.S.A.
Customer Service Hot Line:
1-800-328-7363
8:00 A.M. to 4:30 P.M. Pacific Standard Time
6
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
TO ASSEMBLE YOUR BASSINET
NOTE: Playard MUST be in a locked set-up position before
installing and using the bassinet feature.
CONTENTS (Fig. 1):
1 Nylon bassinet insert
4 Metal support tubes 2 (male) (2 female)
ASSEMBLY
1. Insert the 2 female tubes into the two male tubes. (Fig. 2)
2. Insert the 2 assembled tubes through the loops provided on the
bassinet insert. (Fig. 3).
3. Place assembled bassinet onto the Playard. Push down each of the
bassinet supports onto the playard frame as shown in (Fig. 4).
Figure 1
NOTE: The printed warning label should be facing toward the
inside of the bassinet so that it is readable.
4. Place the Playard mattress into the bassinet with the padded side
facing up (Fig. 5).
Figure 2
5. Connect the canopy to the Playard frame as shown in (Fig. 6)
PLEASE NOTE THE CANOPY IS INTENDED FOR INDOOR
USE ONLY.
Figure 3.
Figure 6.
Figure 5.
Figure 4.
7
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
TO ASSEMBLE CHANGING AREA
CONTENTS (Fig. 1):
•
•
•
2 Long curved bars
2 Short bars with connector knobs
1 Changing area fabric
WARNING:
Figure 1
Avoid serious injury or death:
• Always use restraint belt to prevent falls
• Use changer with infant who’s weight is less
than 18 lbs (8.2 kg ) and is less than 25 inches
(63.5 cm) tall.
• Discontinue use of changer if infant can push
up on hands and knees or sit unassisted.
Figure 2
• DO NOT carry changer with infant in it.
• Always stay within arms reach of your child
when using the changing area.
WARNING: Strangulation Hazard
Child can lift the changing table and get
neck trapped between the changing table
frame and the play yard frame. Never leave
the changing table in place when the child is
in the bassinet or the play yard. Always flip
changer to the outside when not in use.
Holes face
down
Figure 3
WARNING FALL HAZARD:
To prevent death or serious injury, always
keep child within arm’s reach.
Figure 4.
ASSEMBLY
1. Connect the two Long Curved Bars together as shown in figure 2.
2. Insert the assembled Curved Bars into the Changing Area Fabric
such that the holes in the ends of the Curved Bars face downward
as shown in Figure 3.
3. Slide the Curved Bars around inside the sleeve of the Changing
Area Fabric.
4. Connect the Short Bars with Connector Knobs to the Curved
Bars as shown in figure 4. When assembling the Short Bars with
Connector Knobs make sure that the knobs will be facing inward
when assembled and the snap buttons are facing downward.
Completed assembly
Figure 5.
8
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
NOTE: Short bar with connector knobs should be facing
inward.
5. Place connector knob prongs into holes located on corner pieces
of Playard (Fig. 5).
6. Turn connector knobs counter clockwise to lock (Fig. 6).
7. Flip changing area to inside of Playard (Fig.7).
8. Snap flap from changing area to side of Playard (Fig. 8).
9 Check that changing area is secure before using.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
REMOVALAND FOLDING CHANGING AREA
REMOVAL
1. Flip changing area to the outside of the Playard. Unsnap fabric flap
of changing area from Playard.
2. Twist connector knobs clockwise to unlock (Fig. 1).
3. Remove changing area from Playard (Fig. 2).
4. Disconnect the short bars from the curved bar by pressing on the
snap buttons and pulling apart. Remove curved bar from changing
area sleeve.
Figure 1.
The changing area is now ready for storage.
Figure 2.
9
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
REMOVAL OF BASSINET
REMOVAL OF BASSINET
1. Remove mattress from bassinet (Fig.1).
2. Remove canopy (Fig. 2).
3. Un snap all clips and lift bassinet out of playard (Fig. 3)
The bassinet is now ready for storage.
NOTE: Store bassinet and changing area with folded Playard
in carry bag.
Figure 1
Figure 3
Figure 2
TO REMOVE CANOPY
REMOVAL OF CANOPY
To remove the bassinet canopy, pull upward on the ends of the canopy
from the side of the playard. The canopy can be stored in the travel
bag.
USING THE MUSIC CENTER
WARNING: Keep batteries out of child’s
reach. Old and new batteries should not be
mixed. Alkaline, standard carbon-zinc, and
rechargeable nickel-cadium batteries should
notbemixed. Removebatteriesbeforestoring
music center for a long period of time.
10
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
MUSIC CENTER
attach here
The music center is designed to be attached to the playard. Flip
changing table to the outside of the playard and attach music center
to the corner as shown in figure 1.
MUSIC OPERATION
The music center requires 4 AA batteries. Please see figure 2 for
battery installation. Unscrew the battery door screws and pull
outward on the battery door. Install batteries as shown. Re-install
battery door and secure with screws.
Figure 1
ON
To active the unit, press the on/off button. Press button a second time
OFF
to enable voice activation. Press button a third time to switch unit off.
To listen to SLEEP music, press the SLEEP button. You may use the
vol
vol
_
+
_
previous / next button to change the song. The Vol
or Vol
buttons
sleep
control the units volume.
To listen to PLAY music, press the PLAY button. You may use the
previous / next button to change the song. The Vol
control the units volume
To listen to NATURE sounds, press the NATURE button you may use
the previous / next button to change the sound. The Vol
buttons control the units volume.
+
_
vol
vol
or Vol buttons
+
_
play
vol
vol
+
or Vol
nature
VIBRATION
To use the vibration button press down once
to active the speed,
Figure 2
press again for a Medium speed and once more for the faster speed.
Press to reduce the speed.
NIGHT LIGHT
To use the night light, press the
brightness and is controlled by the
button. The light has 3 settings of
button.
Recording Indicator
rec
play
VOICE RECORDER
rec
play
To use the Voice record function press the
button and speak into the
play
microphone to record your 10 second voice message. Press
the message.
to hear
rec
vol
ON
VOICE ACTIVATION
sleep play nature
OFF
To use the Voice Activation function press the OONFF button twice if the
unit is power off. If the unit is already power on, press the
once. The voice activation light will be illuminated when in voice
activation mode. If your infant cries his/her voice will activate the
sleep music to come on and play. When voice activation is enabled,
sleep mode is active for 2 hrs.
nxt
prev
ON
OFF
vol
ON
Voice Activation
Indicator
button
OFF
mp3
input
MP3 FUNCTION
MP3 Indicator
mp3
Use the input jack to attach your MP3 player into the unit . Press the
button to select the MP3 input. Your MP3 music will then be played
thru the unit and will over-ride the unit’s music. To listen to the unit’s
input
music, depress the
player.
button. Volume will be controlled by the MP3
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE CONTACT OUR CUSTOMER
SERVICE DEPARTMENT AT 1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC
STANDARD TIME FOR ASSISTANCE.
11
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
|