INTRODUCTION
BASIC SAFETY INFORMATION
USER’S MANUAL
120V PLUG-IN CARBON MONOXIDE ALARM
WITH SILENCE FEATURE
•
•
•
Dangers, Warnings, and Cautions alert you to important operating
instructions or to potentially hazardous situations. Pay special
attention to these items.
THIS IS NOT A SMOKE ALARM! This CO Alarm is designed to detect
carbon monoxide from ANY source of combustion. It is NOT designed
to detect smoke, fire, or any other gas.
This CO Alarm is approved for use in single-family residences.
It is NOT designed for marine use.
•
•
This CO Alarm will only indicate the presence of carbon monoxide
gas at the sensor. Carbon monoxide gas may be present in other
areas.
120V AC ~ 60 Hz
.085A Standby .087A Alarm
The Silence Feature is for your convenience only and will not correct
a CO problem. Always check your home for a potential problem after
any alarm. Failure to do so can result in injury or death.
M08-0016-000 P 06/02
Model FCD2N
•
•
This CO Alarm cannot operate without continuous electricity. It does
not operate during a power failure.
NEVER ignore your Carbon Monoxide Alarm if it alarms. Refer to
“If Your CO Alarm Sounds” for more information. Failure to do so can
result in injury or death.
IMPORTANT!
PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about your Carbon
Monoxide (CO) Alarm’s operation. If you are installing this CO Alarm for use
by others, you must leave this manual—or a copy of it—with the end user.
•
•
Test the CO Alarm once a week. If the CO Alarm ever fails to test
correctly, have it replaced immediately! If the CO Alarm is not work-
ing properly, it cannot alert you to a problem.
This product is intended for use in ordinary indoor locations of family
living units. It is not designed to measure CO levels in compliance
with Occupational Safety and Health Administration (OSHA) commer-
cial or industrial standards. Individuals with medical conditions that
may make them more sensitive to carbon monoxide may consider
using warning devices which provide audible and visual signals for
carbon monoxide concentrations under 30 ppm. For additional infor-
mation on carbon monoxide and your medical condition contact your
physician.
THIS USER’S MANUAL HAS BEEN RESIZED TO
PRINT OUT ON 8-1/2 x 11” PAGES.
BLACK page numbers reference the original printed document.
RED page numbers reference this web version.
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Basic Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
How Your CO Alarm Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
What the Lights and Alarm Tones Mean . . . . . . . . . . . . . . . . . . . . . . . .2
HOW YOUR CO ALARM WORKS
GENERAL INFORMATION
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Where to Install CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Where CO Alarms Should NOT Be Installed . . . . . . . . . . . . . . . . . . . . .2
How to Install Your CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
If Your CO Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
If the Alarm Signal Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Finding the Source of CO After an Alarm . . . . . . . . . . . . . . . . . . .3 & 4/3
Using the Silence Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Testing and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
What You Need To Know About CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
What is CO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Symptoms of CO Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Potential Sources Of CO In The Home . . . . . . . . . . . . . . . . . . . . . . . . .4
How Can I Protect My Family? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Leave your CO Alarm plugged in year-round. CO problems can occur any
time during the year, and this Alarm can only alert you if it is plugged in
and receiving power.
This CO Alarm is intended for use in a standard, unswitched 120V AC wall
outlet. It is not intended for use in extension cords, power strips, or outlets
controlled by a switch or dimmer. These may not provide continuous power to
the unit.
When fully powered, it samples the air and takes a new reading about every
second. A microchip inside the unit stores each reading, and remembers the
levels of CO it has been exposed to over time. The unit goes into alarm mode
when it has been exposed to a “critical” level of CO (measured in parts per
million or “ppm”) within a specified time (measured in minutes).
This Carbon Monoxide Alarm features a permanently installed sensor, three
colored indicator lights, and an 85dB alarm horn. It also has a Silence Feature
to temporarily quiet the alarm horn.
Underwriters Laboratories Inc. UL2034 . . . . . . . . . . . . . . . . . . . . . . . .5-6/5
General Limitations Of CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6/5
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6/6
Five-Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6/6
THE COVER OF YOUR CO ALARM
1
2
3
4
5
6
Test/Silence Button
POWER Light (Green)
SERVICE Light (Yellow)
ALARM Light (Red)
Air Vents
All Rights Reserved. © 2002 BRK Brands, Inc.
BRK Brands, Inc., 3901 Liberty Street Road, Aurora, IL 60504-8122
Consumer Affairs: (800) 323-9005
(Behind the Cover) Alarm
Horn: 85dB audible alarm
for test, alarm, and unit
malfunction warning.
MALFUNCTION WARNING
This unit performs self-diagnostic tests approximately every second.
If the Alarm malfunctions, it should be replaced immediately.
1
HOW TO INSTALL YOUR CO ALARM
USING THE SILENCE FEATURE
This CO Alarm cannot operate without continuous electricity. It does not
operate during a power failure. Do not use in an extension cord, or out-
let controlled by a dimmer or switch—unit must have a constant power
supply.
The Silence Feature is for your convenience only and will not correct a
CO problem. Always check your home for a potential problem after any
alarm. Failure to do so can result in injury or death.
NEVER unplug your CO Alarm to silence the horn. Use the silence fea-
ture. Unplugging the CO Alarm removes your protection! See “If Your
CO Alarm Sounds” for details on responding to an alarm.
Leave your CO Alarm plugged in year-round. CO problems can occur any
time during the year, and this alarm can only alert you if it is plugged in
and receiving power.
The Silence Feature is intended to temporarily silence your CO Alarm’s alarm
horn while you correct the problem—it will not correct a CO problem. While
the alarm is silenced, it will continue to monitor the air for CO.
1. Plug the unit into a standard UNSWITCHED 120V AC outlet. In horizontally
or vertically positioned wall outlets, mount unit with Test/Silence button
facing upward.
When CO reaches alarm levels, the alarm will sound— repeating horn pattern:
4 beeps, a pause, 4 beeps, etc. Press and hold the Test/Silence button until
the horn is silent. The initial Silence cycle will last approximately 4 minutes.
2. Make sure green light shines when you plug in the unit. It will shine contin-
uously when unit is receiving power. The horn will “chirp” once during
power up, or when power is restored after an outage.
NOTE:
3. Test by pressing the Test/Silence button firmly until the unit sounds: four
loud beeps, pause, 4 beeps. The sequence should last 5-6 seconds.
During testing, the green, yellow, and red lights flash. This is normal.
After initial 4-minute Silence cycle, the CO Alarm re-evaluates present CO
levels and responds accordingly. If CO levels remain potentially dangerous—
or start rising higher—the horn will start sounding again.
4. While testing the unit, have a family member check that the horn can be
easily heard from the sleeping areas. The unit should be located where it
can wake you if it alarms at night.
While the detector is silenced:
If the CO Alarm...
This means...
5. Find the pair of self-adhesive labels included with this CO Alarm.
Is silent for only 4 minutes, then
starts sounding loudly—4 beeps,
then a pause, 4 beeps, then a
pause. Red light continues
flashing...
CO levels are still potentially
dangerous.
• On each label write in the phone number of your emergency responder
(like 911) and a qualified appliance technician.
• Place one label near the CO Alarm, and the other label in the “fresh air”
location you plan to go if the alarm sounds.
NOTE: A qualified appliance technician is defined as “a person, firm, corpora-
tion, or company that either in person or through a representative, is engaged in
and responsible for the installation, testing, servicing, or replacement of heating,
ventilation, air conditioning (HVAC) equipment, combustion appliances and
equipment, and/or gas fireplaces or other decorative combustion equipment.”
If the CO Alarm...
This means...
Remains silent.
Only the green light is on....
Unit has returned to
normal operation.
IF YOUR CO ALARM SOUNDS
Actuation of your CO alarm indicates the presence of carbon monoxide
(CO) which can kill you. In other words, when your CO Alarm sounds,
you must not ignore it!
TESTING AND MAINTENANCE
WEEKLY TESTING
IF THE ALARM SIGNAL SOUNDS:
1. Operate the Test/Silence button.
Test the CO Alarm once a week. If the CO Alarm ever fails to test correct-
ly, have it replaced immediately! If the CO Alarm is not working properly,
it cannot alert you to a problem.
2. Call your emergency services, fire department or 911. Write down the
number of your local emergency service here:
__________________________________________________________________
Push and hold the Test/Silence button on the cover until a loud alarm
sounds— 4 beeps, a pause, then 4 beeps. The alarm sequence should last for
5-6 seconds. If the CO Alarm ever fails to test properly, replace it immediately.
3. Immediately move to fresh air—outdoors or by an open door or window.
Do a head count to check that all persons are accounted for. Do not re-
enter the premises, or move away from the open door or window until the
emergency services responder has arrived, the premises have been aired
out, and your CO Alarm remains in its normal condition.
If the CO Alarm is not working properly, refer to the “Limited Warranty” at the
end of this manual.
4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour
period, repeat steps 1-3 and call a qualified appliance technician to inves-
tigate for sources of CO from fuel-burning equipment and appliances, and
inspect for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately. Note any
combustion equipment not inspected by the technician, and consult the
manufacturers’ instructions, or contact the manufacturers directly, for
more information about CO safety and this equipment. Make sure that
motor vehicles are not, and have not, been operating in an attached
garage or adjacent to the residence. Write down the number of a qualified
appliance technician here:
The Test/Silence button is the only proper way to test the CO Alarm.
NEVER use vehicle exhaust! Exhaust may cause permanent damage and
voids your warranty.
DO NOT stand close to the CO Alarm when the horn is sounding.
Exposure at close range may be harmful to your hearing. When testing,
step away when horn starts sounding.
REGULAR MAINTENANCE
_________________________________________________________________
To keep the CO Alarm in good working order:
•
•
Test it every week using the Test/Silence button.
Vacuum the CO Alarm cover at least twice a year, using the soft brush
attachment. Test the CO Alarm again after vacuuming.
“ALARM-MOVE TO FRESH AIR”
If you hear the alarm horn and the red light is
flashing, move everyone to a source of fresh air.
DO NOT unplug the CO Alarm!
DO NOT spray cleaning chemicals or insect sprays directly on or near
the CO Alarm. DO NOT paint over the CO Alarm. Doing so may cause
permanent damage.
FINDING THE SOURCE OF CO AFTER AN ALARM
Because CO may dissipate by the time an investigator arrives, it may be diffi-
cult to locate the source of CO. See “What You Need to Know About CO.”
BRK Brands, Inc. shall not be obligated to pay for any carbon monoxide
investigation or service call.
Household cleaners, aerosol chemicals and other contaminants can affect the
sensor. When using any of these materials near the CO Alarm, make sure the
room is well ventilated.
If your home is being fumigated, unplug the unit temporarily and put it where
it will not be exposed to chemicals or fumes. When fumigation is complete
and all traces of fumes clear, plug the unit back in and retest it.
3
The following conditions can result in transient CO situations:
WHAT YOU NEED TO KNOW ABOUT CO
WHAT IS CO?
1. Excessive spillage or reverse venting of fuel appliances caused by outdoor
conditions such as:
CO is an invisible, odorless, tasteless gas produced when fossil fuels do not
burn completely, or are exposed to heat (usually fire). Electrical appliances
typically do not produce CO.
• Wind direction and/or velocity, including high, gusty winds. Heavy air in
the vent pipes (cold/humid air with extended periods between cycles).
• Negative pressure differential resulting from the use of exhaust fans.
These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline,
kerosene, and propane.
• Several appliances running at the same time competing for limited
fresh air.
Common appliances are often sources of CO. If they are not properly main-
tained, are improperly ventilated, or malfunction, CO levels can rise quickly.
CO is a real danger now that homes are more energy efficient. “Air-tight”
homes with added insulation, sealed windows, and other weatherproofing can
“trap” CO inside.
• Vent pipe connections vibrating loose from clothes dryers, furnaces, or
water heaters.
• Obstructions in or unconventional vent pipe designs which can amplify
the above situations.
2. Extended operation of unvented fuel burning devices (range, oven,
fireplace).
SYMPTOMS OF CO POISONING
These symptoms are related to CO POISONING and should be discussed
with ALL household members.
3. Temperature inversions, which can trap exhaust close to the ground.
4. Car idling in an open or closed attached garage, or near a home.
Mild Exposure:
Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).
These conditions are dangerous because they can trap exhaust in your
home. Since these conditions can come and go, they are also hard to recreate
during a CO investigation.
Medium Exposure:
Throbbing headache, drowsiness, confusion, fast heart rate.
Extreme Exposure:
Convulsions, unconsciousness, heart and lung failure. Exposure to carbon
monoxide can cause brain damage, death.
HOW CAN I PROTECT MY FAMILY?
A CO Alarm is an excellent means of protection. It monitors the air and
sounds a loud alarm before carbon monoxide levels become threatening for
average, healthy adults.
Some individuals are more sensitive to CO than others, including people
with cardiac or respiratory problems, infants, unborn babies, pregnant
mothers, or elderly people can be more quickly and severely affected by
CO. Members of sensitive populations should consult their doctors for
advice on taking additional precautions.
A CO Alarm is not a substitute for proper maintenance of home appli-
ances.
To help prevent CO problems and reduce the risk of CO poisoning:
•
Clean chimneys and flues yearly. Keep them free of debris, leaves, and
nests for proper air flow. Also, have a professional check for rust and cor-
rosion, cracks, or separations. These conditions can prevent proper air
movement and cause backdrafting. Never “cap” or cover a chimney in
any way that would block air flow.
FINDING THE SOURCE OF CO AFTER AN ALARM
Carbon monoxide is an odorless, invisible gas, which often makes it difficult
to locate the source of CO after an alarm. These are a few of the factors that
can make it difficult to locate sources of CO:
•
•
•
House well ventilated before the investigator arrives.
Problem caused by “backdrafting.”
•
•
Test and maintain all fuel-burning equipment annually. Many local gas or
oil companies and HVAC companies offer appliance inspections for a
nominal fee.
Transient CO problem caused by special circumstances.
Make regular visual inspections of all fuel-burning appliances. Check
appliances for excessive rust and scaling. Also check the flame on the
burner and pilot lights. The flame should be blue. A yellow flame means
fuel is not being burned completely and CO may be present. Keep the
blower door on the furnace closed. Use vents or fans when they are
available on all fuel-burning appliances. Make sure appliances are
vented to the outside. Do not grill or barbecue indoors, or in garages
or on screen porches.
BRK Brands, Inc. shall not be obligated to pay for any carbon monoxide
investigation or service call.
POTENTIAL SOURCES OF CO IN THE HOME
•
Check for exhaust backflow from CO sources. Check the draft hood on
an operating furnace for a backdraft. Look for cracks on furnace heat
exchangers.
•
•
Check the house or garage on the other side of shared wall.
Keep windows and doors open slightly. If you suspect that CO is escaping
into your home, open a window or a door. Opening windows and doors
can significantly decrease CO levels.
In addition, familiarize yourself with all enclosed materials. Read this
manual in its entirety, and make sure you understand what to do if your
CO Alarm sounds.
Fuel-burning appliances like: portable heater, gas or wood burning fireplace,
gas kitchen range or cooktop, gas clothes dryer.
Damaged or insufficient venting: corroded or disconnected water heater
vent pipe, leaking chimney pipe or flue, or cracked heat exchanger, blocked or
clogged chimney opening.
Improper use of appliance/device: operating a barbecue grill or vehicle in an
enclosed area (like a garage or screened porch).
Transient CO Problems: “transient” or on-again-off-again CO problems can
be caused by outdoor conditions and other special circumstances.
4
UNDERWRITERS LABORATORIES INC. UL2034
Standards: Underwriters Laboratories Inc. Single and Multiple Station carbon
WHAT LEVELS OF CO CAUSE AN ALARM?
Underwriters Laboratories Inc. UL2034 defines 3 specific alarm points by
which all residential CO Alarms must alarm. They are measured in parts per
million (ppm) of CO over time (in minutes).
monoxide alarms UL2034.
According to Underwriters Laboratories Inc. UL2034, Section 1-1.2: “Carbon
monoxide alarms covered by these requirements are intended to respond to
the presence of carbon monoxide from sources such as, but not limited to,
exhaust from internal-combustion engines, abnormal operation of fuel-fired
appliances, and fireplaces. CO Alarms are intended to alarm at carbon
monoxide levels below those that could cause a loss of ability to react to
the dangers of Carbon Monoxide exposure.” This CO Alarm monitors the air
at the Alarm, and is designed to alarm before CO levels become life threat-
ening. This allows you precious time to leave the house and correct the
problem. This is only possible if Alarms are located, installed, and main-
tained as described in this manual.
UL2034 Required Alarm Points*:
•
•
•
If the alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN
4 and 15 MINUTES
If the alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN
10 and 50 MINUTES.
If the alarm is exposed to 70 ppm of CO, IT MUST ALARM BETWEEN
60 and 240 MINUTES.
Gas Detection at Typical Temperature and Humidity Ranges: The CO
Alarm is not formulated to detect CO levels below 30 ppm typically. UL tested
for false alarm resistance to Methane (500 ppm), Butane (300 ppm), Heptane
(500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol (200 ppm) and Carbon
Dioxide (5000 ppm). Values measure gas and vapor concentrations in parts
per million.
* Approximately 10% COHb exposure at levels of 15% to 95% Relative
Humidity (RH).
The unit is designed not to alarm when exposed to a constant level
of 30 ppm for 30 days.
Audible Alarm: 85dB minimum at 10 feet.
CO Alarms are designed to alarm before there is an immediate life threat.
Since you cannot see or smell CO, never assume it’s not present.
•
•
An exposure to 100 ppm of CO for 20 minutes may not affect average,
healthy adults, but after 4 hours the same level may cause headaches.
An exposure to 400 ppm of CO may cause headaches in average, healthy
adults after 35 minutes, but can cause death after 2 hours.
This CO Alarm measures exposure to CO over time. It alarms if CO levels are
extremely high in a short period of time, or if CO levels reach a certain mini-
mum over a long period of time. The CO Alarm generally sounds an alarm
before the onset of symptoms in average, healthy adults.
Why is this important? Because you need to be warned of a potential CO
problem while you can still react in time. In many reported cases of CO expo-
sure, victims may be aware that they are not feeling well, but become disori-
ented and can no longer react well enough to exit the building or get help.
Also, young children and pets may be the first affected. The average healthy
adult might not feel any symptoms when the CO Alarm sounds. However,
people with cardiac or respiratory problems, infants, unborn babies, pregnant
mothers, or elderly people can be more quickly and severely affected by CO.
If you experience even mild symptoms of CO poisoning, consult your doctor
immediately!
GENERAL LIMITATIONS OF CO ALARMS
This CO Alarm is intended for residential use. It is not intended for use in
industrial applications where Occupational Safety and Health
Administration (OSHA) requirements for carbon monoxide detectors must
be met.
CO Alarms are not a substitute for a smoke alarm. Although fire is a source
of carbon monoxide, this CO Alarm does not sense smoke or fire. This CO
Alarm senses CO that may be escaping unnoticed from malfunctioning fur-
naces, appliances, or other sources. Early warning of fire requires the installa-
tion of smoke alarms.
CO Alarms will not work without power. This CO Alarm requires a continu-
ous supply of AC power. Plug into an unswitched 120V AC outlet only.
CO Alarms are not a substitute for life insurance. Though these CO Alarms
warn against increasing CO levels, BRK Brands, Inc. does not warrant or imply
in any way that they will protect lives from CO poisoning. Homeowners and
renters must still insure their lives.
This CO Alarm will not sense carbon monoxide that does not reach the
sensor. This CO Alarm will only sense CO at the sensor. CO may be present in
other areas. Doors or other obstructions may affect the rate at which CO
reaches the CO Alarm. For this reason, if bedroom doors are usually closed at
night, we recommend you install a CO Alarm in each bedroom and in the hall-
way between them.
CO Alarms have a limited life. Although the CO Alarm and all of its parts
have passed many stringent tests and are designed to be as reliable as possi-
ble, any of these parts could fail at any time. Therefore, you must test your CO
Alarm weekly.
CO Alarms may not sense CO on another level of the home. For example,
a CO Alarm on the second level, near the bedrooms, may not sense CO in the
basement. For this reason, one CO Alarm may not give adequate warning.
Complete coverage is recommended. Place CO Alarms on each level of the
home.
CO Alarms are not foolproof. Like all other electronic devices, CO Alarms
have limitations. They can only detect CO that reaches their sensors. They
may not give early warning to rising CO levels if the CO is coming from a
remote part of the home, away from the CO Alarm.
CO Alarms may not be heard. The alarm horn loudness meets or exceeds
current UL standards of 85 dB at 10 feet. However, if the CO Alarm is installed
outside the bedroom, it may not wake up a sound sleeper or one who has
recently used drugs or has been drinking alcoholic beverages. This is espe-
cially true if the door is closed or only partly open. Even persons who are
awake may not hear the alarm horn if the sound is blocked by distance or
closed doors. Noise from traffic, stereo, radio, television, air conditioner, or
other appliances may also prevent alert persons from hearing the alarm horn.
This CO Alarm is not intended for people who are hearing impaired.
5
TROUBLESHOOTING GUIDE
PROBLEM...
THIS MEANS...
YOU SHOULD...
Green light is OFF. Unit will not alarm when you press
the Test/Silence button.
CO Alarms may not be plugged all the way in, or is
not receiving power.
Gently push unit all the way into outlet.
Make sure it is not plugged into an outlet controlled
by a switch.
Unit “chirps” about twice a minute. Green and Yellow
Malfunction. CO Alarm needs to be replaced.
CO levels are still potentially dangerous.
Make sure unit is plugged in securely. CO Alarms
under warranty should be returned to manufacturer
for replacement. See “Limited Warranty” for details.
lights are ON. Red light FLASHES
CO Alarm goes back into alarm 4 minutes after you
press the Test/Silence button.
Refer to “If Your CO Alarm Sounds” for details on
how to respond to an alarm. If anyone is feeling ill,
EVACUATE your home immediately.
CO Alarm sounds frequently even though no high lev-
els of CO are revealed in an investigation.
The CO Alarm may be improperly located. Refer to
“Where to Install CO Alarms.”
Relocate your Alarm. If frequent alarms continue,
have home rechecked for potential CO problems.
You may be experiencing an intermittent CO problem.
If you have any questions that cannot be answered by reading this manual, call Consumer Affairs at 1-800-323-9005.
FIVE-YEAR LIMITED WARRANTY
Coverage: BRK Brands, Inc. ("BRK") the maker of First Alert® brand products, warrants that for a period of 5 years from the date of purchase, this product will be
free from defects in material and workmanship. BRK, at its option, will repair or replace this product or any component of the product found to be defective during
the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be
made with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase
is required to obtain warranty performance. BRK dealers, service centers, or retail stores selling BRK products do not have the right to alter, modify
or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage
or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than BRK or an authorized service center. Further, the war-
ranty does not cover acts of God, such as fire, flood, hurricanes and tornadoes or any batteries that are included with this unit.
BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by
applicable law, any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Some states,
provinces, or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so
the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to
state, or province to province.
How to Obtain Warranty Service:
Service: If service is required, do not return the product to your retailer. In order to obtain warranty service, contact the Consumer Affairs Division at
1-800-323-9005, 7:30 AM to 5:00 PM, Central Standard Time, Monday through Friday. To assist in serving you, please have the model number and date
of purchase available when calling.
3920 Enterprise Court, Aurora, IL 60504-8132.
For your records, please record:
Date Purchased: ____________________________
Where Purchased: ___________________________
First Alert® is a registered trademark of the First Alert Trust.
M08-0016-000 P 06/02
6
|