Analog Door Phone
Model ADP1
Installation and Use Manual
© 2004 Bogen Communications, Inc.
All rights reserved.
Specifications subject to change without notice.
54-2098-01B 0607
Description
TheADP1 is a convenient remote,weatherproof,hands-free two-way terminal device for
telephone systems.
The unit is telephone line powered and includes adjustable microphone and speaker vol-
ume levels as well as a selectable Auto Answer feature to allow for remote monitoring.
The ADP1 also includes an adjustable and defeatable call timer and can respond to
forward disconnect signals.
The ADP1 features a heavy-gauge stainless steel gasketed faceplate, plastic cone speaker,
and faceplate to electrical box (user supplied) gasketing to protect against vandals and
varying weather conditions. A dress bezel is included with the unit for trimming out
rough openings in flush mount applications.
Package Contents
•
•
•
•
•
(1) ADP1
(4) Hex drive screws
(1) Hex wrench
(1) Bezel
(1) Bezel gasket
3
Settings
ADP1
PC Board
7
NOISE
REDUCTION OFF
4
5
1. TEL Line Connector - Analog station line connection (Tip and Ring) is made via
an RJ11 connector that is pre-wired to a 2-position pluggable terminal block. The
connections to the terminal block are not polarity sensitive. (See Wiring, pg. 5.)
2. Speaker Volume POT - The Speaker Volume POT controls the speaker volume
level of the unit. Clockwise rotation (looking at POT) increases the volume.
3. Microphone Level POT - The Microphone Level POT adjusts the microphone
return talk level of the unit. In certain noisy locations (e.g., background traffic,
machinery, or wind) the microphone threshold level may need to be decreased, oth-
erwise the unit might detect the background noise as valid audio thereby causing the
unit to remain in the talk mode. Clockwise rotation (looking at POT) increases the
return talk level.
4. Noise Reduction - Slowly mutes the level to the phone when only
background noise, not active audio, is detected.
5. Active LED - For use when installing and troubleshooting, the LED indicates that
the unit is active (off hook) when lit.
6. Timer / Timer Duration POT - The ADP1 can be configured to
automatically disconnect a call after a preset amount of time has
elapsed.The timer can be set between 15 seconds and 2 minutes.The
timer is activated by pressing the button on the unit or when the unit answers (Auto
Answer) an incoming call.With the timer disabled, the call time will be unlimited and
the ADP1 will not disconnect the call until a 300 ms or longer loss of loop current
is detected.If the telephone line/phone system extension does not supply a loop cur-
rent break when the calling party hangs up, then the call timer feature must be used
(enabled). Clockwise rotation of the POT increases the duration.
7. Auto Answer - The ADP1 can be configured to automatically
answer an incoming call.This feature can be enabled or disabled using
a jumper located on the PC board.
4
Wiring
Phone Connection
TheADP1 comes with an RJ11 wired to the pluggable terminal block. Connect theADP1
to the phone system’s analog station line programmed for ring down operation using the
RJ11 or directly to the screw terminals depending on how the lines are terminated.The
connections to the terminal block are not polarity sensitive.
Surge Protection
To increase surge protection, connect a protective Earth Ground to the spare lug
provided. A ring lug is provided to which the protective ground lead is crimped.
Reassemble the lug to post as shown.
5
Installation
The ADP1 is designed to fit in most standard dual gang electrical boxes. Make sure to
use the proper box type for intended installation (e.g., flush or surface mount, indoor
or outdoor location, etc.).
Flush Mounting the ADP1 (Indoor/Outdoor)
1. Cut rough opening and install
appropriate electrical box.
Note: The box must be flush with the
surface within 1/16".
2. For outdoor installations, caulk
around the box, filling any gaps
between the box and the rough
opening.
3. Attach the self-adhesive gasket to
the back side of the bezel.
4. Make electrical connections and
attach the faceplate to the electrical
box while capturing the bezel
between the two using the four hex
drive screws (tool provided).The
faceplate fits into the depression in
the bezel.
Surface Mounting the ADP1
(Indoor/Outdoor)
1. Mount electrical box.
2. Make electrical connections and
attach the faceplate to the electrical
box using the four hex drive screws
(tool provided). Do not use the
bezel for surface mount installations
as the elevated sharp corners of the
bezel could pose a hazard.
6
Specifications
Power:
Telephone line powered
(18V DC / 20 mA minimum)
Timer Duration:
Loop Current Loss Disconnect:
RingVoltage:
15 seconds to 2 minutes
300 ms minimum
40V AC RMS minimum
0.7A
REN:
Connections:
2-position pluggable terminal block
Earth Ground lug
1
Dimensions:
5" W x 5" H x 2 /4" D (fully assembled)
45/8" W x 45/8" H x 2" D (aluminum box)
4 lb.
Product Weight:
7
Warranty
The ADP1 is warranted to be free from defects in material or workmanship for two (2)
years from the date of sale to the original purchaser.Any part of the product covered by
this warranty that, with normal installation and use, becomes defective will be repaired
or replaced by Bogen, at our option, provided the product is shipped insured and prepaid
to: Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. The
product will be returned to you freight prepaid.This warranty does not extend to any of
our products that have been subjected to abuse, misuse, improper storage, neglect, acci-
dent, improper installation or have been modified or repaired or altered in any manner
whatsoever, or where the serial number or date code has been removed or defaced.
THE FOREGOING LIMITEDWARRANTY IS BOGEN'S SOLEAND EXCLU-
SIVEWARRANTY ANDTHE PURCHASER'S SOLE AND EXCLUSIVE REM-
EDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER
EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HERE-
BY DISCLAIMED AND EXCLUDEDTOTHE MAXIMUM EXTENT ALLOW-
ABLE BY LAW. Bogen's liability arising out of the manufacture, sale or supplying of
products or their use or disposition,whether based upon warranty,contract,tort or oth-
erwise, shall be limited to the price of the product. In no event shall Bogen be liable for
special, incidental or consequential damages (including, but not limited to, loss of profits,
loss of data or loss of use damages) arising out of the manufacture, sale or supplying of
products, even if Bogen has been advised of the possibility of such damages or losses.
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you.This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
Products that are out of warranty will also be repaired by the Bogen Factory Service
Department — same address as above or call 201-934-8500.The parts and labor involved
in these repairs are warranted for 90 days when repaired by the Bogen Factory Service
Department. All shipping charges in addition to parts and labor charges will be at the
owner's expense.All returns require a Return Authorization number.
8/10/2004
50 Spring Street, Ramsey, NJ 07446, U.S.A.
|