15-inch Color LCD Flat Panel Display Monitor
Instruction Manual
EN MON150CL
|
MON150CL | Instruction Manual | Safety Precautions
EN 3
Safety Precautions
For Indoor Product
1. Water and Moisture - Do not use this unit near
water - for example, in a wet basement, in an
unprotected outdoor installation or in any area
classified as a wet location.
CAUTION: TO REDUCE THE RISK OF
2. Object and Liquid Entry - Never push objects of
any kind into this unit through openings, as they
might touch dangerous voltage points or create
short circuits, resulting in a fire or electrical
shock. Never spill liquid of any kind on the unit.
3. Power Cord and Power Cord Protection - For
units intended to operate with 230VAC, 50Hz,
the input and output power cord must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that can cause an electric
shock.
This symbol indicates the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
Power supply cords should be routed so they are
not likely to be walked on or pinched. Pay
particular attention to location of cords and plugs,
convenience receptacles, and the point of exit
from the appliance.
Installation should be performed by qualified
service personnel only in accordance with the
National Electrical Code or applicable local
codes.
4. Overloading - Do not overload outlets and
extension cords; this can result in a risk of fire or
electrical shock.
Power Disconnect. Units with or without
ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. The power cord is the main power
disconnect for all units.
For Outdoor Product
Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines,
electric lights or power circuits, or where it may
contact such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching power lines or
circuits, as this contact might be fatal. U.S.A.
models only - refer to the National Electrical
Code Article 820 regarding installation of CATV
systems.
Cover Removal
WARNING: Removal of the cover should only be
performed by qualified service personnel - not user
serviceable. The unit should always be unplugged before
removing the cover and remain unplugged while the
cover is removed.
For Rack-mount Product
1. Ventilation - Do not place this equipment in a
built-in installation or rack, unless proper
ventilation is provided, or the manufacturer's
instructions were followed. The equipment must
not exceed its maximum operating temperature
requirements.
2. Mechanical Loading - When rack-mounting the
equipment, ensure that a hazardous condition is
not created by uneven mechanical loading.
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | FCC & ICES Information
EN 4
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)
(2)
This device may not cause harmful interference, and
This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer, or an experienced radio/TV technician for
help.
Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance, shall
not be made. Any such changes or modifications could void the
user’s authority to operate the equipment.The user may find the
following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV
Interference Problems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Contents
EN 5
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front and Back Panel Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.0
1.1
2.0
3.0
3.1
4.0
4.1
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
6.0
6.1
6.2
7.0
7.1
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Desktop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting the Composite Video Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting the Y/C (S-video) Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting Audio to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting the Analog VGA Signal to the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
On-screen Display (OSD) Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ON-SCREEN DISPLAY MENU CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
CVBS Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
VGA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
7.2
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Front Panel
EN 6
MON150CL
Key:
A. AUTO (Input)Button
B. +, - Buttons
C. MENU Button
D. Power LED Identification
E. Power Button
A
B
C D
E
Figure 1: Front Panel
A
B
C
D
E
A. DC input
B. VGA input
C. Video(CVBS) input
D. Y/C input
E. Audio input
Figure 2: I/O Connectors
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Unpacking
EN 7
1.0 UNPACKING
3.0 GENERAL FEATURES
This high-performance, 15-inch TFT LCD monitor
with a 1024 X 768 XGA resolution has been designed
to display both PC and Video images. It complies with
the power management regulations of VESA DPMS, it
is supported by Plug & Play, and complies with
DDC1/2B.
This equipment should be unpacked and handled with
care. If an item appears to have been damaged in
shipment, notify the shipper.
Verify that all parts shown in the Parts List have been
included. If any items are missing, notify your Bosch
Security Systems Sales or Customer Service
Representative.
3.1 Features
•
•
•
•
•
•
•
•
100 to 240 VAC Power Supply
NTSC/PAL Auto - Detect
High Resolution (1024 X 768 XGA)
PC Input
The original packing carton is the safest container in
which to transport the unit. Save it for possible future use.
1.1 Parts List
Qty Item
Video Input
1
1
2
Unit (verify model number)
Audio Input
MON150CL Color LCD Flat Panel Monitor
Y/C Input
Power Cords: 3-wire with grounded plug, 1.8 m (6 ft)
long; One (1) with European Continental plug type and
one (1) with U.S plug type
OSD with Multiple Languages
1
1
1
1
1
MON150PS power supply
One (1) analog VGA cable, 1.5 m (5 ft)
One (1) audio cable
4.0 INTRODUCTION
4.1 Monitors
RCA to BNC connector
This installation manual
The MON150CL 15-inch (38 cm) Color Liquid Crystal
Display Monitor displays PAL or NTSC standard color
pictures in CCTV systems. The MON150CL monitor
includes one (1) Composite Video input RCA
connector (one RCA to BNC connector is included),
one (1) Audio input mini phone jack, and one (1) Y/C
(S-video) input using 4-pin mini-DIN. In addition, this
model includes an Analog VGA input using 15-pin
D-sub to accommodate the increasing use of Personal
Computers and digital video devices in security
applications. Monitor control functions are accessed
via the front panel push buttons and the multi-
language On-Screen Display (OSD).
2.0 SERVICE
If the unit needs servicing, contact the nearest Bosch
Security Systems Service Center for authorization to
return and shipping instructions.
Service Centers
USA
Phone:
Fax:
800-366-2283 or 717-735-6638
800-366-1329 or 717-735-6639
CCTV Spare Parts
Phone:
Fax:
800-894-5215 or 408-956-3853 or 3854
408-957-3198
5.0 INSTALLATION
E-mail:
Canada
Phone:
5.1 Power
514-738-2434
Model
No.
Rated
Voltage
Range
Power
Sync
Europe, Middle East & Asia Pacific Region
Phone: 32-1-440-0711
Voltage
at Rated Format
Voltage
For additional information, see
MON150CL 120/230 VAC 100 to 240 V 26 W
NTSC/PAL
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Installation
EN 8
5.2 Desktop Installation
The MON150CL monitor is delivered with a 3-pole
US-style power cord and a 3-pole Euro-style power
cord. Use the US-style power cord where 120 VAC,
60 Hz power is available; and use the Euro-style
power cord where 230 VAC, 50 Hz power is available.
Connect the bayonet connector from the power supply
to the power input connector on the rear side of the
LCD panel, as shown in Photo A. The monitor
automatically adjusts to either power input voltage.
Photo C
5.4 Connecting the Y/C (S-video) Signal
to the Monitor
There is one (1) mini-DIN type connector for the
S-video (Y/C) input (please see Figure 2 on Page 6 and
Figure 3 below).
NOTE: Both Y and C inputs are terminated with 75Ω.
3
4
1. GND
2. GND
3. Y-signal IN
4. C-signal IN
Photo A
2
1
5.3 Connecting the Composite Video
Signal to the Monitor
There is one (1) RCA connector located on the rear of
the monitor for composite video input (please see
Figure 2 on Page 6). Also included is one (1) RCA to
BNC adapter used to connect a BNC cable line as
shown in Photo B and Photo C.
Figure 3: Y/C Connection Pinout
5.5 Connecting Audio to the Monitor
There is one (1) set of mini phone jacks for the audio
connector (please see Figure 2 on Page 6 and Photo D
below).
Photo D
Photo B
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Operation
EN 9
5.6 Connecting the Analog VGA Signal
to the Monitor
Contrast
Adjusts the contrast value
(0-100)
There is one (1) 15-pin D-sub connector (Figure 4) for one
analog VGA input. Refer to Figure 2, item B.
Brightness Adjusts the brightness value
(0-100)
Tint
Adjusts the tint value (NTSC only)
(0-100)
Saturation Adjusts the color value
(0-100)
Figure 4: Analog VGA Connector
Volume
Exit
Adjusts the volume
(0-31)
5.7 Ventilation
To prevent overheating, ensure that the ventilation
openings on the rear of the monitor are not covered.
Exits the OSD menu
6.2.2 Colour Setting (RGB / VGA)
Colour Setting
6.0 OPERATION
6.1
Front Panel Controls (Figure 1)
1. Press Menu to open the OSD Main menu
AUTO (Input)
+/-
Press this button to display the input
signal which is selected on the screen
2. Press the ‘+’ or ‘-’ button to highlight an option,
then press Menu to modify the value of the option
Press the ‘+’ or ‘-’ button to move the
cursor to the targeted parameter in the
OSD main menu. Press the ‘+’ or ‘-’
button to adjust the value of the selected
parameter in the OSD sub-menu.
MENU
Press this button to open the main OSD
menu. Use this button to confirm a value
for a parameter in the OSD Menu.
Power LED
Identification
Power on (Green)
Stand by (Amber)
Contrast
Adjusts the contrast value
(0-100)
POWER
Press this button to turn on or turn off
the monitor
Brightness Adjusts the brightness value
(0-100)
6.2 On-screen Display (OSD) Menu
Gamma Correct
6.2.1 Video Setting (CVBS/S-VIDEO)
Opens an optimum Gamma curve
(0/1/2/3)
Saturation
1. Press Menu to open the OSD Main menu
Colour Adjust
Opens the color menu. Select a color
then press Menu to adjust the value of
the selected color.
2. Press the ‘+’ or ‘-’ button to highlight an option,
then press Menu to modify the value of the option
Exit
Exits the Colour OSD menu setting
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | Operation
EN 10
6.2.5
OSD Menu (CVBS/S-VIDEO / RGB / VGA)
6.2.3
Picture Setting (RGB / VGA)
Language Opens the Language Selection Menu
Select one of the following: English,
Deutsch, Francais, Italiano, Espanol,
Simple Chinese, Traditional Chinese,
Japanese
H Position Adjusts the horizontal position
(0-100)
V Position Adjusts the vertical position
(0-100)
OSD
H. Position
Adjusts the OSD horizontal position
(0-100)
Sharpness Adjusts the sharpness value
(1/2/3/4/5)
OSD
V. Position
Adjusts the OSD vertical position
(0-100)
Phase
Clock
Exit
Adjusts the phase value
(0-31)
OSD Time Adjusts the OSD window display time
Adjusts the clock frequency
(0-200)
(0-30)
Translucent Toggles the OSD window background
Exits the Picture OSD Menu setting
setting
6.2.4
Auto Function Setting (RGB / VGA)
Exit
6.2.6
Exits the OSD menu setting
Miscellaneous (CVBS/S-VIDEO / RGB / VGA)
Auto Adjust Automatically adjusts the H/V
position, phase, and clock
Signal Source
Prompts you to select an input source
Auto Position Automatically adjusts the H/V position
Auto Phase Automatically adjusts the phase
Mode Select
Prompts you to select one of these
modes: 640 X 400 or 720 X 400
Auto Clock Automatically adjusts the clock
frequency
Reset
Exit
Returns the monitor setting to the
factory default
Auto Colour Automatically adjusts the color
temperature
Exit
Exits the Function OSD Menu setting
Exits the Miscellaneous menu setting
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration
EN 11
7.0 ON - SCREEN DISPLAY MENU
CONFIGURATION
7.1
CVBS Mode
CVBS
Video Setting
Contrast
Brightness
Tint
Color
Volume
Exit
OSD Menu
Language
English
Deutsch
Francais
Italiano
Espanol
Simple Chinese
Traditional Chinese
Japanese
OSD H. Position
OSD V. Position
OSD Timer
Translucent
Exit
On
Off
On
Off
D-Sub
CVBS
Miscellaneous
Signal Source
S-Video
Mode Select
Reset
Yes
No
Exit
Exit
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration
EN 12
7.2
VGA Mode
RGB (VGA)
Colour
Contrast
Brightness
Gamma Correct
Colour Adjust
Exit
Red
Green
Blue
Exit
Picture
H. Position
V. Position
Sharpness
Phase
Clock
Exit
Yes
No
Function
Auto Adjust
Auto Position
Auto Phase
Auto Clock
Auto Colour
Exit
Yes
No
Yes
No
Yes
No
Yes
No
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual | On-Screen Display Menu Configuration
EN 13
OSD Menu
Language
English
Deutsch
Francais
Italiano
Espanol
Simple Chinese
Traditional Chinese
Japanese
OSD H. Position
OSD V. Position
OSD Timer
Translucent
Exit
On
Off
On
Off
D-Sub
CVBS
S-Video
Miscellaneous
Signal Source
Mode Select
Reset
Yes
No
Exit
Exit
Error Message: Signal Out of Range
This message appears in VGA
7.2.1 Supported Resolutions
VGA Timing Modes
mode if the PC is operating with a
resolution or timing mode that is
not supported by the MON150CL.
Please change the PC settings to
one of the supported VGA Timing
Mode combinations listed.
640 x 480
800 x 600
1024 x 768
60/72/75 Hz
60/72/75 Hz
50/60/70/75 Hz
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual |
EN 14
Bosch Security Systems | May 20, 2005
|
MON150CL | Instruction Manual |
EN 15
Bosch Security Systems | May 20, 2005
Americas
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 (585) 223 4060
+1 800 289 0096
Europe, Middle East, Africa
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
Phone: +31 (0) 40 27 83955
Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180
Phone: +65 6319 3450
Fax:
+31 (0) 40 27 86668
Fax:
+65 6319 3499
© 2005 Bosch Security Systems GmbH
F01U009193_01 05-20 | Updated May 20, 2005 | Data subject to change without notice.
|