Bosch Appliances Smoke Alarm FMM 7045 User Manual

FMM-7045, FMM-7045-D  
Installation Instructions  
Multiplex Addressable  
Manual Pull Stations  
EN  
 
FMM-7045, FMM-7045-D | Installation Instructions | 3.0Specifications  
.
2.3  
Wiring  
2.4  
Mounting  
Make sure all power is removed before  
making any electrical connections. Failure  
to do so may result in personal injury and/or  
damage to equipment.  
The FMM-7045/FMM-7045-D mounts to a 3 in. x 2 in.  
x 3½ in. device box (like a Steel City CXW) or a 4 in.  
x 2 1/8 in. square box with a 5/8 in. mud ring (like the  
Steel City 52171 box and 52-C-14-5/8 mud ring) with  
the two provided screws. The multiplex single zone  
input module should easily fit inside.  
Run all wires and make all connections before  
mounting the FMM-7045/FMM-7045-D. All wiring is  
supervised and power limited. See Figure 2 for details.  
The back plate mounting holes on the FMM-  
7045/FMM-7045-D can be accessed by opening the  
key lock on the unit.  
Do not loop wire around each terminal.  
Break terminal wire connections for  
supervision.  
The FMM-7045/FMM-7045-D Pull Stations  
are for indoor use only. If a pull station is  
needed for outdoor use or in an unheated  
area, an FMM-100 Series Pull Station rated  
for the environment should be wired to a  
multiplex module within the interior of the  
building.  
Figure 2: Wiring the FMM-7045  
2
2
4
1
3
3
3.0 Specifications  
Table 1: Specifications  
L
o
o
p
L
o
o
p
+
-
HUNDREDS  
0
1
2
0
1
2
X X X  
Panel  
Programming  
Type  
Single Point  
0
5
0
1
9
1
9
8
7
2
3
8
7
2
3
6
4
6
4
5
ONES  
TENS  
Control Panel  
Requirements  
D7024 or DS9400 Series FACP (with  
ROM version 2.0 or greater and a  
D7039 or DS9431 Multiplex Expansion  
Module installed). Refer to the D7024  
Operation and Installation Guide (P/N:  
31499) or the DS9400M/DS9400i  
Installation Guide (P/N: 44578) for  
specific programming information. Refer  
to the D7039 Installation Instructions  
(P/N: 38685) or the DS9431  
1 - Previous device or D7039/DS9431  
2 - Loop (+)  
3 - Loop (-)  
Installation Instructions  
41831) for multiplex wiring information.  
(P/N:  
4 - Other devices  
Multiplex Bus  
Average Current  
Draw  
Alarm: 0.55 mA  
Standby: 0.55 mA  
Optional  
Equipment  
Replacement Glass Break Rods (FMM-  
100GR)  
Operating  
Temperature  
+32°F to +120°F (0°C to +49°C) non-  
condensing RH  
Listings and  
Approvals  
UL864  
CSFM  
Nominal Bus  
Voltage  
12 VDC  
Bosch Security Systems, Inc. | 8/06 | F01U001402C  
3
 
Bosch Security Systems, Inc.  
130 Perinton Parkway  
Fairport, NY 14450-9199  
Customer Service: (800) 289-0096  
Technical Support: (888) 886-6189  
© 2006 Bosch Security Systems, Inc.  
F01U001402C  
 

Best Ventilation Hood ISER222 SERIES User Manual
Black Box Portable Generator BLACK BOX Pattern GeneratorVGA User Manual
Bosch Power Tools Planer PLH181B User Manual
Bravetti Food Processor BP101H2 User Manual
BRK electronic Fire Extinguisher BF5 User Manual
Brother Sewing Machine BE 0901E User Manual
Cambridge Audio Stereo Receiver 840A V2 User Manual
Cannon Double Oven 10101G User Manual
CFM Fan 165834 User Manual
Chauvet Welder F 40 User Manual