Bose Speaker System 347205 1300 User Manual

Solo  
TV Sound System  
Owner’s Guide | Brugervejledning | Bedienungsanleitung | Gebruikershandleiding  
Guía del usuario | Käyttöohje | Notice d’utilisation | Manuale di istruzioni  
Kezelési útmutató | Podręcznik użytkownika | Manual do Proprietário | Bruksanvisning  
 
Safety Information  
Please read this guide  
Please take the time to follow the instructions in this owner’s guide carefully. It will help you set up and operate your  
system properly and enjoy its advanced features. Please save this guide for future reference.  
All Bose products must be used in accordance with local, state, and federal regulations.  
The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of  
uninsulated, dangerous voltage within the system enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock.  
The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user  
to the presence of important operating and maintenance instructions in this owner’s guide.  
WARNING: This product contains magnetic material. Please contact your physician if you have any  
questions on whether this might affect the operation of your implantable medical device.  
WARNING: Contains small parts which may be a choking hazard. Not suitable for children under age 3.  
WARNING:  
Never place the equipment in an unstable location. The equipment may fall, causing serious personal  
injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions  
such as:  
Using cabinets or stands recommended by the manufacturer of the equipment.  
Only using furniture that can safely support the equipment.  
Ensuring the equipment is not overhanging the edge of the supporting furniture.  
Not placing the equipment on tall furniture (for example, cupboards or bookcases) without anchoring  
both the furniture and the equipment to a suitable support.  
Not standing the equipment on cloth or other materials placed between the equipment and supporting  
furniture.  
Educating children about the dangers of climbing on furniture to reach the equipment or its controls.  
If you doubt your ability to safely mount your television or set up this product, contact a professional  
installer for help.  
WARNING: Allowing children to push, pull, or climb on a television connected to this equipment may  
cause it to tip over, possibly resulting in personal injury or death. For added safety and stability, be sure to  
secure the television using a suitable anti-tip device.  
English - 3  
 
Safety Information  
WARNING:  
To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture.  
Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such  
as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any  
part of the system. Liquids can cause a failure and/or a fire hazard.  
Do not place any naked flame sources, such as lighted candles, on or near the apparatus.  
WARNING:  
Keep the remote control battery away from children. It may cause a fire or chemical burn if mishandled.  
Do not recharge, disassemble, heat above 212ºF (100ºC), or incinerate. Dispose of used batteries  
promptly. Replace only with a battery of the correct type and model number.  
Do not ingest battery, chemical burn hazard. The remote control supplied with this product contains a  
coin/button cell battery. If the coin/button cell battery is swallowed it can cause severe internal burns  
in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery  
compartment does not close securely, stop using the product and keep it away from children. If you  
think the battery may have been swallowed or placed inside any part of the body seek immediate  
medical attention.  
Danger of explosion if battery is incorrectly replaced. Replace only with an agency-approved (e.g. UL)  
CR2032 or DL2032 3-volt lithium battery.  
CAUTION: Make no modifications to the system or accessories. Unauthorized alterations may  
compromise safety, regulatory compliance, and system performance, and may void the warranty.  
Notes:  
Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall  
remain readily operable.  
The product must be used indoors. It is neither designed nor tested for use outdoors, in recreation vehicles, or  
on boats.  
The product label is located on the bottom or the back of the product.  
Please dispose of used batteries properly, following any local regulations.  
Do not incinerate.  
This product conforms to all applicable EU Directive requirements. The complete Declaration of  
Names and Contents of Toxic or Hazardous Substances or Elements  
Toxic or Hazardous Substances and Elements  
Part Name  
Lead  
(Pb)  
Mercury Cadmium Hexavalent  
Polybrominated  
Biphenyl (PBB)  
Polybrominated  
diphenylether (PBDE)  
(Hg)  
(Cd)  
(CR(VI))  
PCBs  
X
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Metal parts  
Plastic parts  
Speakers  
Cables  
X
X
0: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit  
requirement in SJ/T 11363-2006.  
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is  
above the limit requirement in SJ/T 11363-2006.  
4 - English  
 
Safety Information  
Important Safety Instructions  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s  
8. instructions.  
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and  
the point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the manufacturer.  
12. Unplug this apparatus during lightning storms or when unused for long periods of time.  
13. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in  
a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into  
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has  
been dropped.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-  
ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions, may cause harmful interference to radio communica-  
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause harmful interference to radio or television reception, which can be determined by turning the equipment  
off and on, you are encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by Bose Corporation could void the user’s authority to operate  
this equipment.  
Complies with the Canadian ICES-003 Class B specifications.  
Please complete and retain for your records  
The serial and model number can be found on the bottom panel.  
Serial number: _________________________________________________________________  
Model number: ________________________________________________________________  
Purchase date: ________________________________________________________________  
We suggest you keep your receipt with this owner’s guide.  
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are  
registered trademarks of Dolby Laboratories.  
©2013 Bose Corporation. No part of this work may be reproduced, modified, distributed, or otherwise used without  
prior written permission.  
English - 5  
 
Introduction  
ank you…  
®
Thank you for choosing the Bose Solo TV sound system for your home. This  
stylish, unobtrusive speaker system is designed to fit under most TVs with screens  
up to 32 inches, and many TVs with screens up to 42 inches. It delivers superb  
acoustic performance that will greatly enhance your TV viewing experience.  
Unpacking  
Carefully unpack the carton and confirm that you have all the parts shown here:  
Bose Solo TV sound system  
Remote  
Power cord  
Optical digital audio cable  
Analog stereo audio cable  
(The appropriate power cord  
for your region is included)  
Coaxial digital audio cable  
If any part of the product appears to be damaged, do not attempt to use it. Contact  
your authorized Bose dealer immediately or call Bose Customer Service. Refer to  
the contact list enclosed in the carton for contact information.  
Be sure to save the carton and packing materials. They provide the safest means  
for transporting or storing the product.  
6 - English  
 
System Setup  
Step 1: Place the system  
A. Move your TV aside and turn it so you  
A
can see the connection panel.  
B. Place the Solo system where you had  
your TV.  
B
Placement guidelines:  
The Bose Solo system is designed to fit  
under TVs that weigh no more than 40 lb  
(18 kg) and have bases no wider than 20"  
(508 mm) and no deeper than 10¼" (260  
mm). Many 42" and most 32" TVs and  
smaller meet these requirements.  
The base of your TV should be centered on the top of the system and must  
not hang over any of its edges.  
If the TV base is too large to fit on top of the system, place the sound system  
in another location such as on an open shelf under the TV, but keep it close to  
your TV so the audio cable will reach. You also could mount your TV on the  
wall above the system.  
If placing the sound system in a cabinet, or on a shelf, position the front of  
the system as close as possible to the front edge of the shelf for optimum  
audio performance.  
Note: Placing the system in a corner, in a cabinet, or on a shelf may cause the  
system audio to sound heavy or have a booming bass quality. To decrease  
the bass, see “Decreasing the bass” on page 20.  
CAUTIONS:  
DO NOT place a CRT type TV on this system. It is not designed for use with this  
type of TV.  
Allowing the base of your TV to hang over any edge of this speaker system  
increases the risk of the TV tipping, which may result in injury.  
If placing the sound system backed up to a wall, make sure there is a space of at  
least 1" (2.5 cm) between the wall and the rear of the system.  
With any placement of this product, make sure the ventilation openings on the  
rear panel are not blocked.  
If your TV comes with an anti-tip device, install it according to the manufacturer’s  
instructions and adjust the tether as instructed after placing the TV on top of the  
system. Installing an anti-tip device is recommended when using a TV with this  
product. If your TV did not come with an anti-tip device, you can get one from  
most retail TV suppliers.  
English - 7  
 
System Setup  
Step 2: Connect the Solo system to power  
A. Plug one end of the power cord into the AC input connector.  
B. Plug the other end into a live AC power (mains) outlet.  
A few moments after applying power, the system emits two tones indicating  
that it is ready to use.  
AC input connector  
100-240V  
50/60 Hz  
50W  
Note: Bose recommends using a safety agency-approved surge protector on all  
electronic equipment. Voltage variations and spikes can damage electronic  
components in any system.  
8 - English  
 
System Setup  
Step 3: Choose the type of audio cable to use  
On the back of your TV, look for one of the following audio output connections and  
locate the cable for the one you want to use. Refer to the unpacking diagram on  
page 6.  
Choose only one  
Audio OUT connection  
Remove cap  
OR  
OR  
Optical digital audio  
Coaxial digital audio  
Analog stereo audio  
A digital audio output  
that passes digital  
data through a fiber  
optic cable.  
A digital audio output  
that passes digital  
data through a 75-ohm  
coaxial cable.  
The most common  
type of audio output  
where the left and right  
channel are connected  
separately.  
If available, use this  
connection for best  
audio performance.  
Use this connection if  
an optical output is not Use this connection if  
available.  
no digital audio outputs  
are available.  
Tip: If your TV does not have any audio outputs, you can use the audio outputs  
on another device. For example, if a cable or satellite box is connected to  
your TV, you can connect audio outputs from that device to the Solo system.  
See “Alternate Setup Connections” on page 16 for other ways to connect  
the Solo TV sound system.  
English - 9  
 
System Setup  
Step 4: Plug the audio cable into the Solo system  
Tip: If you selected the optical digital audio cable, see “Important instructions for  
optical cable connections” on page 11.  
A. Plug one end of the selected audio cable into the correct Audio IN connector  
on the Solo system.  
Solo system Audio IN  
Make only one connection  
OR  
OR  
Remove cap  
B. If you wish, you can slide the cable behind the built-in cable clip.  
(Optical cable shown only for example.)  
Cable clip  
Audio IN connectors  
10 - English  
 
System Setup  
Important instructions for optical cable connections  
1. Remove the protective cap from both ends of the cable.  
Remove cap  
2. Hold the optical cable plug as shown . Align the plug with the Optical  
connector and insert the plug carefully  
.
Note: The connector has a hinged door that swings out of the way when  
inserting the plug.  
Hinged  
door  
CAUTION: Inserting the plug in the wrong orientation can damage the plug  
and/or the connector.  
3. Firmly push the plug into the connector until you hear or feel a click.  
English - 11  
 
System Setup  
Step 5: Plug the other end of the audio cable into  
your TV  
A. Find the Audio OUT connections on your TV.  
B. Plug the other end of the audio cable into the correct Audio OUT connector.  
CAUTION: If using an optical digital audio cable, make sure you hold the plug in  
the correct orientation for the Audio OUT connector on your TV. You may need to  
rotate the plug differently than you did for the Solo system.  
Optical audio cable  
shown only for example  
TV Audio OUT  
12 - English  
 
System Setup  
Step 6: Place your TV on the Solo system.  
Place your TV on the Solo system, making sure the TV stand is centered on the  
top of the system. Refer to “Placement guidelines:” on page 7.  
CAUTION: Be sure to center the base of your TV on the top of this product.  
CAUTIONS:  
DO NOT place a CRT type TV on this system. It is not designed for use with  
this type of TV.  
Allowing the base of your TV to hang over any edge of this speaker system  
increases the risk of the TV tipping, which may result in injury.  
If placing the sound system backed up to a wall, make sure there is a space of at  
least 1" (2.5 cm) between the wall and the rear of the system.  
If your TV comes with an anti-tip device, install it according to the manufacturer’s  
instructions and adjust the tether as instructed after placing the TV on top of the  
system. Installing an anti-tip device is recommended when using a TV with this  
product. If your TV did not come with an anti-tip device, you can get one from  
most retail TV suppliers.  
English - 13  
 
System Setup  
Step 7: Check your TV settings  
To enjoy the full benefit of hearing TV audio through the Solo TV sound system, the  
internal speakers in your TV should be turned off. Also, you need to make sure that  
some audio settings do not inhibit the audio output signal.  
Note: Check the user manual for your TV for help on using the TV menus and  
changing any TV settings. Manufacturers usually make user manuals  
available on their web sites.  
A. Turn on your TV.  
B. Go to the TV menu and select Audio, Sound, or Speaker Settings.  
C. Look for the menu item that allows you to turn off the TV speakers. This  
menu item may be called Speakers On/Off or something closely related.  
If there is no setting for turning the TV speakers off, adjust the TV volume to its  
lowest setting.  
D. If you decided to use either an optical or coaxial digital audio output, look for a  
menu item in the Audio Settings that may affect digital audio output. You may  
have to select the digital output you want to use.  
E. Look for any setting that selects the type of audio output, such as Stereo or  
5.1 Channel Audio output. You may need to select such a setting in order to  
enable the audio output.  
14 - English  
 
System Setup  
Step 8: Check for sound  
A. Press the power button on the Solo system remote.  
Make sure the system status indicator is solid green.  
System status indicator  
B. Make sure your TV is on.  
C. Check if sound is coming from the Solo system speakers.  
Tip: To confirm your TV speakers are off, press the mute button on the Solo  
system remote and check that no sound is coming from the TV. The system  
status indicator on the front panel blinks green when the system is muted.  
Note: Depending on where you placed your Solo system and the program  
currently playing, you may notice that the audio sounds too heavy or has a  
booming bass quality. To decrease the amount of bass in the audio output,  
see “Decreasing the bass” on page 20.  
If you do not hear sound from the Solo speaker system:  
Make sure the Solo system is on. The system status indicator (page 19)  
on the front panel should be solid green.  
Using the Solo system remote, increase the volume.  
Make sure the audio cable is plugged into a connector on your TV labelled  
Audio Output or Audio OUT, not Audio Input or Audio IN.  
If using the optical digital audio cable, make sure it is seated correctly.  
Refer to “Important instructions for optical cable connections” on page  
11. If you still hear no audio after checking the cable installation, try  
another type of audio connection.  
See “Alternate Setup Connections” on page 16 for other ways to connect  
to the Solo system.  
English - 15  
 
Alternate Setup Connections  
When to use an alternate connection  
You may discover that your TV does not provide audio outputs or when you have  
connected one of its audio outputs to the Solo system your TV may not deliver the  
audio to the Solo system.  
If you have difficulty getting sound from the Solo system when it is directly  
connected to your television, one of these alternate connection schemes may help.  
If your TV does not have any audio output connections or does not deliver  
the audio to the Solo system, see  
“Connecting to a cable box audio output” below, or  
“Connecting to a TV headphones output” on page 17.  
If you do not get sound from a DVD player that is connected to your TV, see  
“Connecting multiple devices to the Solo system” on page 18.  
Connecting to a cable box audio output  
Instead of connecting your TV to the system, you can connect one of the cable box  
audio outputs to the Solo system. Be sure to use only one audio connection.  
CAUTION: If you choose to make an optical digital cable connection, refer to  
“Important instructions for optical cable connections” on page 11.  
Make only one connection  
Remove  
cap  
OR  
OR  
Audio OUT  
Cable box  
Audio IN  
Solo system  
16 - English  
 
Alternate Setup Connections  
Connecting to a TV headphones output  
If your TV only has a headphones jack, you can connect this audio output to the  
Solo system using a Dual RCA to 3.5 mm stereo cable.  
After making this connection, turn your TV volume up to near maximum and control  
the volume with the Solo system remote.  
Audio OUT  
TV headphones or other  
variable audio output  
This connection requires a  
Dual RCA to 3.5mm stereo  
cable (not included).  
Audio IN  
Solo system  
English - 17  
 
Alternate Setup Connections  
Connecting multiple devices to the  
Solo system  
If you have a device such as a DVD player connected to your TV, you may discover  
that your TV does not pass audio from the DVD player to the audio output on your  
TV. The Solo system provides a solution to this problem. You can connect up to  
three devices to the Solo system using a different type of audio cable for each. For  
example, the figure below shows a cable box and a DVD player connected to the  
Solo system.  
Note: This alternate connection scheme may not work with the equipment you  
have in your home because some devices like cable/satellite boxes always  
remain on. When multiple devices are connected to the Solo system, turn  
on only the device you want to use and turn off the others.  
CAUTION: If you choose to make an optical digital cable connection, refer to  
“Important instructions for optical cable connections” on page 11.  
Audio OUT  
Cable box  
Audio OUT  
DVD player  
Audio IN  
Solo system  
18 - English  
 
Operation  
Remote control  
The Solo TV sound system is easily operated using the small remote control.  
Just point the remote at the front of the system and press the buttons.  
Turns the sound system on or off  
Raises (+) the system volume  
Lowers (–) the system volume  
Mutes or unmutes the system sound  
System status indicator  
The system status indicator tells you when the system is on and provides you with  
a system status during operation.  
System status  
indicator  
System status:  
Off.........................................System off (standby)  
Solid green ...........................Power is on  
Fast blinking green...............System is muted  
Very fast blinking green ........Volume is being adjusted  
Solid amber ..........................Decreased bass setting  
Solid red ...............................System error - call Bose Customer Service  
English - 19  
 
Operation  
Decreasing the bass  
Depending on the placement of your Solo system or the program currently playing,  
the audio may produce more bass than you would like.  
To select the decreased bass setting  
1. Point the remote at the system.  
2. Press and hold the Mute button  
until the following happens:  
The system mutes the audio, plays three descending tones (going down) and  
flashes the status indicator (page 19) amber three times. Audio returns and the  
status indicator turns solid amber.  
3. Release the Mute button.  
To return to the normal bass setting  
1. Point the remote at the system.  
2. Press and hold the Mute button  
until the following happens:  
The system mutes the audio, plays three ascending tones (going up) and  
flashes the status indicator (page 19) green three times. Audio returns and the  
status indicator turns solid green.  
3. Release the Mute button.  
Optional universal remote control  
A universal remote control is available from Bose that can operate this system and  
be programmed to control your TV and other components connected to it. Contact  
Bose Corporation or your local dealer for more information. See the contact list  
included in the carton.  
Using a third-party remote  
A third-party remote, such as your set-top box remote, can be programmed to  
control your Solo system.  
Referring to the owner’s guide for your set-top box remote, follow the instructions  
for programming the remote to control a TV. When it is time to enter a device code,  
the owner’s guide for the cable remote should tell you what to enter for a Bose  
system. Once programmed, the third-party remote should control basic functions  
such as power on/off and volume.  
20 - English  
 
Care and Maintenance  
Troubleshooting  
Problem  
What to do  
TV base is too  
large to place on  
the system  
Place the sound system in another location such as on an open shelf  
under the TV.  
If possible mount your TV on the wall above the sound system.  
System will not  
turn on  
Make sure the power cord is securely connected on both ends.  
Make sure the power cord is plugged into a live AC (mains) outlet.  
If the outlet is controlled by a switch, make sure the switch is in the  
ON position or test the outlet using a lamp.  
Reset the system: Unplug the power cord for at least one  
minute. Plug the power in again and listen for the system to emit two  
tones confirming it has power.  
No sound  
Make sure the sound system is turned on and the power  
indicator is on (solid green).  
Make sure the sound system is not muted.  
Increase the volume.  
Make sure the audio cable connection is correct and secure on the  
sound system and the TV.  
Make sure the TV is on and set to the correct input.  
If you are using a digital audio connection, make sure that the digital  
audio output is not disabled in your TV. See your TV owner’s guide  
for information.  
If a digital audio connection is not possible, use an analog stereo  
audio connection.  
If the sound system is connected to a TV output labelled  
VARIABLE (VAR), make sure the TV internal speakers are turned off,  
the TV volume is turned up, and the TV is not muted.  
Turn off all devices connected to the Solo system except the one  
you want to hear.  
Remote control  
is inconsistent or  
does not work  
Check the battery to be sure it is installed properly or if it needs to  
be replaced. See “Replacing the remote battery” on page 22.  
Point the remote control at the sound system when you press a  
button.  
Check that the system status indicator on the sound system flashes  
when you press the remote volume or mute button.  
Audio sounds too Change the bass setting to decrease the amount of bass. See  
heavy, too much  
bass  
“Decreasing the bass” on page 20.  
Change the position or orientation of the system. In some situations  
the system may produce more bass. See Placement Guidelines on  
page 7.  
Sound is  
distorted  
Make sure cable connections are secure on the Solo system and TV.  
If the sound system is connected to a TV output labelled  
VARIABLE (VAR), reduce the TV volume.  
Bypass the TV and connect directly to the source using one of the  
Alternate setup methods (page 16).  
Sound is coming Turn off your TV’s internal speakers.  
from the TV  
Adjust the TV volume.  
System status  
indicator is red  
System error. Call Bose Customer Service.  
English - 21  
 
Care and Maintenance  
Replacing the remote battery  
When the remote stops operating or its range seems reduced, it is time to change  
the remote battery.  
WARNING: Keep battery (or batteries) away from children, May cause a fire or  
chemical burn if mishandled. Do not recharge, disassemble, heat above 212°F  
(100°C), or incinerate. Dispose of used batteries promptly. Replace only with a  
battery of the correct type and model number.  
1. Using a coin, turn the battery cover slightly counterclockwise.  
2. Remove the cover and insert the new battery (CR2032 or DL2032) flat side up,  
with the plus (+) symbol in view.  
3. Re-seat the cover and turn it clockwise to lock into place.  
Cleaning  
You can clean the surface of the speaker with a soft, dry cloth.  
Do not use any sprays near the speaker. Do not use any solvents, chemicals,  
or cleaning solutions containing alcohol, ammonia, or abrasives.  
Do not allow liquids to spill into any openings.  
The speaker grille requires no special care, although you may carefully vacuum  
it with a brush attachment, if necessary.  
22 - English  
 
Care and Maintenance  
Customer service  
For additional help in solving problems, contact Bose Customer Service. Refer to  
the address sheet included with the Solo TV sound system.  
In the U.S. only, call: 800-901-0472.  
Limited warranty  
®
Your Bose Solo TV sound system is covered by a limited warranty. Details of the  
limited warranty are provided on the product registration card that is included in  
the carton. Please refer to the card for instructions on how to register. Failure to  
register will not affect your limited warranty rights.  
Technical information  
Power rating  
100-240V  
50/60 Hz 50W  
Dimensions  
20¾" (525.00 mm) W x 12¼" (308.96 mm) D x 3" (73.50 mm) H  
Weight  
10.1 lb (4.6 kg)  
English - 23  
 

Bissell Carpet Cleaner 1699V User Manual
Bissell Vacuum Cleaner 47R5 User Manual
Bolens Tiller 300 User Manual
Braun Blender MR 6550 M FP HC User Manual
Braun Iron SI 6290 User Manual
Broan Air Cleaner HRV90H User Manual
Canon Camcorder CR 1 MARK II User Manual
Casio Musical Instrument LK300TV User Manual
Celestron Telescope 21013 User Manual
Chevrolet Automobile 2000 User Manual