Bose Stereo System AM189930 User Manual

The Bose® Wave® Radio  
Owner’s Guide  
January 4, 2002  
AM189930_01_V.pdf  
FPO  
 
Safety Instructions  
For your safety  
1. Read, Follow, And Save All Instructions – Read and follow the complete safety and operating  
instructions in this owner’s guide before using the unit. Save this guide for future reference.  
2. Pay Attention To Warnings – Observe all warnings on the unit and in the guide.  
3. Do Not Let Objects Or Liquid Enter The Unit – Take care to prevent objects or liquids  
from entering this unit. Do not use near a bathtub, washbowl, kitchen sink, laundry tub, in  
a wet basement, near a swimming pool, or anywhere else that water is present. Clean only  
as directed on page 18.  
4. Maintain Proper Ventilation – Place the unit so nothing interferes with its proper ventilation.  
Do not place on a bed, sofa, or similar surface that mayblocktheventilation openings. Do not put  
it in a bookcase or cabinet that may keep air from flowing through its ventilation openings.  
5. Avoid Excessive Heat – Do not place the unit near heat sources such as radiators, stoves,  
or other appliances (including amplifiers) that produce heat.  
6. Use Proper Power Sources – Plug the unit into a proper power supply, as described in the  
operating instructions or as marked on the unit. This unit has a polarized alternating current  
line plug (one blade is wider than the other). As a safety feature, the plug fits into the power  
outlet only one way. If you have trouble inserting it, reverse the plug. If it still does not fit,  
your outlet may be obsolete and needs to be replaced. Contact an electrician. Do not  
change the plug to defeat this safety feature.  
7. Protect The Power Cord – Route all power cords so that they are not likely to be walked on  
or pinched. Pay particular attention to cords at plugs, at the point where the cord connects  
to the unit, and at outlets on the unit.  
8. Take Precautions When Unit Is Not In Use – If the unit will not be used for an extended  
period, unplug from the outlet and remove the batteries.  
9. Be Careful With Carts And Stands – Do not place this unit on an unstable cart, stand,  
tripod, bracket, or table. The unit may fall, causing serious injury to a person or damage to  
the unit. For advice on use of a particular cart, stand, tripod, bracket, or table, contact  
Bose® Corporation. Be careful when moving the unit and cart combination. Quick stops,  
excessive force, and uneven surfaces may cause it to overturn.  
10. Avoid Power Lines – Do not install external antennas near overhead power lines or other  
electric light or power circuits, nor where an antenna can fall into such circuits or power lines.  
Antenna  
Lead In Wire  
11. Ground All Outdoor Antennas – If an external antenna or cable system is connected to this  
unit, be sure the antenna or cable system is grounded. This will provide some protection  
against voltage surges and built-up static charges.  
Ground  
Clamp  
Antenna  
Discharge Unit  
(NEC Section 810-20)  
Section 810 of the National Electrical Code ANSI/NFPA No. 70 provides information with  
respect to proper grounding of the mast and supporting structure, grounding of the lead-in  
wire to an antenna discharge unit, size of the grounding conductors, location of antenna-  
discharge unit, connection to grounding electrodes, and requirements for the ground  
electrode. Refer to the antenna grounding illustration.  
Grounding  
Conductors  
(NEC Section 810-21)  
Electric  
Service  
Equipment  
Ground Clamps  
Power Service Grounding  
Electrode System  
(NEC ART 250 Part H)  
Note to CATV system installer:  
This reminder calls the CATV system  
installer’s attention to Article 820-40 of  
the NEC (of USA) that provides  
12. Obtain Authorized Service When It Is Indicated – Do not attempt to service this unit  
yourself. All servicing should be provided by authorized service personnel when:  
A. The power supply cord or the plug has been damaged, or  
guidelines for proper grounding. It  
specifies that the cable ground shall be  
connected to the grounding system of  
the building, as close to the point of  
cable entry as is practical.  
B. Objects have fallen or liquid has spilled into the unit, or  
C. The unit has been exposed to rain, or  
D. The unit does not appear to operate normally or exhibits a marked change in performance, or  
E. The unit has been dropped or the cabinet damaged.  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
3
Contents  
Please read this owner’s guide  
The Bose® Wave® radio is carefully engineered to provide sound quality far beyond other  
radios. This guide will help you set up and operate your radio properly.  
Where to find...  
Safety Instructions  
Cautions ................................................................................................................. 3  
For your safety ....................................................................................................... 3  
Setting Up  
Unpack the carton.................................................................................................. 5  
Install the batteries ................................................................................................. 5  
Connect the power cord ........................................................................................ 6  
The remote control ................................................................................................. 7  
The Display  
How to read the clock display ............................................................................... 8  
How to read the radio display ................................................................................ 8  
How to customize the display................................................................................ 9  
Functions  
Radio functions .................................................................................................... 10  
Clock functions .................................................................................................... 12  
Other Components  
Connecting other components ............................................................................ 16  
Using other components...................................................................................... 17  
Product Information  
Maintaining the Wave radio ................................................................................. 18  
For best radio reception....................................................................................... 18  
Features................................................................................................................ 18  
Bose® Corporation  
Warranty ............................................................................................................... 19  
Customer service ................................................................................................. 19  
4
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Setting Up  
Unpack the carton  
Carefully unpack the carton. Do not attempt to use the Wave® radio if any part appears  
damaged. Instead, repack the carton and notify Bose® or your authorized Bose dealer immedi-  
ately.  
It is best to place the radio across the room from where you will be listening. Place the radio on  
a table or other flat surface. Do not put it on a metal surface or table that could interfere with  
AM reception. If you will use the radio with your television or VCR, do not place it on top of the  
television. It may interfere with the picture quality.  
Locate the power cord, AA batteries, remote control, and lithium battery.  
Figure 1  
What comes with your radio.  
• Wave radio  
• Power cord  
• Remote control  
• Lithium battery  
• AA batteries  
Wave  
radio  
3 AA batteries  
®
SLEEP  
TIME ALARM  
.
STA  
ING  
TUN  
3
2
1
PRESET STATIONS  
5
6
4
MUTE  
VOLUME  
Remote control  
AM  
FM  
ON/OFF  
AUX  
RC-1  
NTROL AW  
R
EMOTE CO  
CEIVER  
WAVE RE  
ACOUSTIC  
Power cord  
Lithium  
battery  
Install the batteries  
The Wave radio’s three AA batteries maintain the memory and backup alarm system for up to a  
week during a power failure, or while the radio is unplugged. Operating without batteries leaves  
the memory unprotected, but will not harm the radio. Use AA batteries (IEC-R6 in Europe),  
available at many retail stores.  
Note: The batteries will not power the radio or  
light the display.  
Figure 2  
Installing the batteries.  
+ +  
1. Carefully turn your radio upside down (avoid  
scratching its top).  
2. Locate the battery compartment on the  
bottom (see Figure 2).  
3. Press the arrow on the cover to slide the  
compartment open.  
4. Place the batteries inside, matching the +  
and – symbols with the symbols inside the  
compartment.  
V A R I A B L E O U T  
5. Slide the cover back and turn the radio right  
side up.  
A U X I N  
R
L
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
5
Setting Up  
Connect the power cord  
1. Plug the small end of the power cord into the power jack on the back of your radio (see  
Figure 3). Line up the flat edge of the plug with the flat edge on the side of the jack.  
Figure 3  
Connecting the power cord.  
R
AUX IN  
L
120V AC  
50/60Hz 50W  
VARIABLE OUT  
2. The FM antenna is built into the power cord. To improve FM reception, unwind the power  
cord completely.  
3. Plug the other end of the power cord into an electric outlet.  
4. The display panel lights and the time display begins flashing after the power is connected.  
Press the CLOCK SET button once to stop the flashing.  
6
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Setting Up  
Note:  
The remote control  
Replace only with a Duracell,  
Eveready, Maxell, or Toshiba  
CR2032 or DL2032 lithium battery  
(available at most electronics  
stores). If you have difficulty finding  
a replacement battery, contact  
Bose® Customer Service (see  
phone numbers on the inside back  
cover).  
Install the battery  
Your Wave® radio remote control has a security lock to prevent children from reaching the small  
battery. Follow these steps to insert or remove the battery.  
1. Place the remote control upside down and face down (as shown in Figure 4a).  
2. Insert the tip of a pen into the small hole in the security lock (Figure 4a). If your pen does  
not have a long fine point, you can use a straightened paper clip instead.  
3. Tilt the pen to push the lock in the direction shown by the arrow in Figure 4b. Push the  
lock until the battery compartment clicks open.  
Note: If you have difficulty getting the lock to click open, use the pen to hold the lock to  
the side while pulling the battery carrier out. You can place a thin coin or other object in  
the battery carrier slot to help pull the battery carrier out.  
Figure 4  
Push the security lock toward the  
battery carrier slot, until the battery  
compartment lock clicks open.  
battery carrier slot  
b
a
b a t t e r y t o b e u s e d  
i n s t r u c t i o n s f so r et y cp ue s rio tf y  
lock  
S e e o p e r a t i n g  
b a t t e r y t o b e u s e d  
o n o r t y p e s o f  
r a t i n g  
o p e  
r u c t i  
4. Slide the battery carrier out. Insert the battery into the battery carrier, with the + symbol  
facing up, as shown in Figure 5.  
5. Slide the battery carrier closed. Do not force it. It automatically locks in place.  
Figure 5  
Insert the battery with the + symbol  
facing up.  
WARNING:  
The remote control battery may  
cause a fire or chemical burn if  
mishandled. Keep it away from  
children. Do not recharge,  
See operating  
battery to be used  
instructions for types of  
disassemble, heat above 100˚C  
(212˚F), or incinerate. Dispose of  
used battery promptly. Replace  
with a battery of the type and  
model mentioned in the note  
above. Using another battery may  
cause a fire or explosion.  
battery carrier  
How to operate  
Aim the remote control at your Wave radio. Use the remote keys in the same way you use the  
radio control panel. The remote normally works up to 20 feet in front of the radio, and 6 feet to  
either side. Replace the remote control battery when it stops operating, or its range seems  
reduced (normally every year or two).  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
7
The Display  
How to read the clock display  
Figure 6A  
The clock display.  
[Numeric display] – Shows current time, wakeup time, time remaining before  
automatic shutoff, station frequency, or volume setting.  
Lights to indicate  
Alarm 1 is on.  
Lights to indicate  
sound selected for  
Alarm 1.  
ALARM  
AM  
PM  
Lights to indicate  
sound selected for  
Alarm 2.  
ALARM 2  
SLEEP  
One will light to  
indicate AM or PM.  
Lights to indicate  
Sleep Mode is selected.  
Lights to indicate  
Alarm 2 is on.  
Note:  
The display automatically adjusts  
as the light in your room changes.  
In normal lighting the display is  
bright. In darker rooms the display  
dims.  
How to read the radio display  
Figure 6B  
The radio display.  
Lights to show auxiliary source, FM, or  
AM band selected.  
Lights while  
[Numeric display] –  
Shows station  
frequency, current  
time, wakeup time,  
time remaining before  
automatic shutoff, or  
volume setting.  
receiving FM  
stereo broadcast.  
AUX FM  
STEREO  
Lights while  
VOL AM  
SEEK  
volume setting  
is displayed.  
PRESET  
1
2
3
4
5
6
Lights while  
radio  
automatically  
searches for a  
strong signal.  
Lights when you  
preset a station.  
Lights when you select  
a preset station.  
8
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
The Display  
How to customize the display  
Function  
Keys  
Action  
Press ON/OFF once to turn your Wave®  
radio off.  
AM/PM (12 hour)  
or  
ON/OFF  
Military (24 hour)  
time  
Hold down CLOCK SET and press ON/OFF  
to switch between AM/PM (12 HR) or military  
(24 HR) formats.  
CLOCK  
SET  
ON/OFF  
AM/FM  
and  
In clock mode, the display shows the time  
while the radio is on; in radio mode, the display  
shows the radio station that is selected.  
Clock or radio  
mode  
CLOCK  
SET  
With the radio turned on, hold down the  
CLOCK SET button and press the AM/FM  
button to switch between clock and radio modes.  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
9
Radio Functions  
Radio Control Operation  
To turn on/off  
Press ON/OFF once to turn on (automatically selects the last  
source played) or to turn off. Selecting any preset also turns  
the radio on.  
ON/OFF  
Press AM/FM to turn the radio on. Press again to  
switch between FM and AM.  
AM/FM  
AUX  
Press AUX once to listen to a component connected to the  
AUX IN jacks. (This does not turn on the component).  
To shut off  
automatically  
Press SLEEP/SNOOZE to set automatic shutoff. The display  
shows 75 minutes. Press again, or press and hold, to reduce  
the time until shutoff to 60, 45, 30, 15, 10, 5, or 0 minutes.  
SLEEP/SNOOZE  
ON/OFF  
AM/FM  
Press ON/OFF to turn off the radio before automatic shutoff.  
To select AM  
or FM  
If the radio is off or in AUX mode, press AM/FM to select  
the radio. Press again to select AM or FM.  
To adjust  
volume  
While the radio is on or off, press either VOLUME button and  
hold to reset the volume.  
The display shows the volume level from 0 (soft) to 99 (loud).  
VOLUME  
To display  
the station  
If the display is in clock mode and the radio is on, press both  
TUNING buttons simultaneously to display the current station  
for several seconds.  
TUNING  
To tune in  
a station  
Press and hold either TUNING button until the desired station  
is selected.  
TUNING  
To seek  
a station  
Press and hold either TUNING button until you hear a beep.  
Then release to find the next strong signal. Turn the volume  
up, if necessary, to hear the beep.  
TUNING  
To preset up  
to 6 AM and  
6 FM stations  
Use the TUNING buttons to find the desired station. Then,  
hold down any PRESET button until you hear a beep. The  
station is now preset to that button.  
TUNING  
PRESET STATIONS  
To tune in  
a preset  
Choose AM or FM. Press the PRESET button for the station  
you want.  
PRESET STATIONS  
AM/FM  
10  
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Radio Functions  
Remote Control Operation  
To turn on/off  
Press ON/OFF once to turn on (automatically selects the last  
source played) or to turn off. Selecting any preset also turns  
the radio on.  
ON/OFF  
AM  
FM  
Press AM/FM to turn the radio on. Press again to  
switch between FM and AM.  
Press AUX once to listen to a component connected to the  
AUX IN jacks. (This does not turn on the component).  
AUX  
To shut off  
automatically  
Press SLEEP to set automatic shutoff. The display shows 75  
minutes. Press again, or press and hold, to reduce the time  
until shutoff to 60, 45, 30, 15, 10, 5, or 0 minutes.  
SLEEP  
ON/OFF  
Press ON/OFF to turn off the radio before automatic shutoff.  
To select AM  
or FM  
If the radio is off or in AUX mode, press AM/FM to select  
the radio. Press again to select AM or FM.  
AM  
FM  
To adjust  
volume  
While the radio is on or off, press either VOLUME button and  
hold to reset the volume.  
The display shows the volume level from 0 (soft) to 99 (loud).  
Press MUTE to silence the radio.  
VOLUME  
MUTE  
Press again to restore volume.  
To display  
the station  
If the display is in clock mode and the radio is on, press STA.  
STA.  
To tune in  
a station  
Press and hold either TUNING button until the desired station  
is selected.  
TUNING  
To seek a  
station  
Press and hold either TUNING button until you hear a beep.  
Then release to find the next strong signal. Turn the volume  
up, if necessary, to hear the beep.  
TUNING  
To preset up  
to 6 AM and  
6 FM stations  
Use the TUNING buttons to tune to the desired station. Then  
hold down any PRESET button until you hear a beep. The  
station is now preset to that button.  
TUNING  
1
4
2
3
6
PRESET STATIONS  
5
To tune in  
a preset  
Choose AM or FM. Press the PRESET button for the station  
you want.  
1
4
2
3
6
AM  
FM  
PRESET STATIONS  
5
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
11  
Clock Functions  
Radio Control Operation  
While holding down the CLOCK SET button,  
press either TUNING button. The time display  
changes slowly at first, then more quickly. It  
stops when you release the TUNING button.  
To set the  
clock  
CLOCK  
SET  
TUNING  
To set  
Alarm 1  
wake up  
time and  
alarm sound  
Note: You can set the alarm with the radio on or off.  
ALARM  
SET  
Hold down ALARM SET and press either TUNING  
button. The time display changes slowly at first, then  
more quickly. It stops when you release any button.  
TUNING  
To change the Alarm 1 sound, press ALARM MODE.  
For tone only, press until the ( ) indicator lights.  
When the alarm goes off, the tone volume gradually  
increases to your preset level.  
ALARM MODE  
For radio only, press until the ( ) indicator lights.  
When the alarm goes off, the radio volume gradually  
increases to your preset level.  
For tone and radio, press until both indicators (  
)
light. When the alarm goes off, the tone sounds. After  
you press SLEEP/SNOOZE, the radio turns on.  
To set  
Alarm 2  
wake up  
time and  
alarm sound  
Note: You can set the alarm with the radio on or off.  
ALARM  
SET  
Hold down ALARM SET and press ALARM MODE. The  
Alarm 2 indicator flashes. You now have 10 seconds to  
begin setting Alarm 2.  
ALARM MODE  
Note: The Alarm 2 indicator must be flashing while setting  
Alarm 2 wake up time or sound.  
TUNING  
To set Alarm 2 wake up time, hold down ALARM SET and  
press either TUNING button.  
ALARM MODE  
To change Alarm 2 sound, press ALARM MODE while the  
Alarm 2 indicator flashes.  
For tone only, press until the ( ) indicator lights. When the  
alarm goes off, the tone volume gradually increases to your  
preset level.  
For radio only, press until the ( ) indicator lights. When the  
alarm goes off, the radio volume gradually increases to your  
preset level.  
For tone and radio, press until both indicators (  
) light.  
When the alarm goes off, the tone sounds. After you press  
SLEEP/SNOOZE, the radio turns on.  
Note: The Alarm 2 indicator continues flashing for 10  
seconds after wake up time and sound are set.  
12  
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Clock Functions  
Remote Control Operation  
You cannot set the clock with the remote control.  
To set the  
clock  
Note: You can set the alarm with the radio on or off.  
To set  
Alarm 1  
wake up  
time and  
alarm sound  
TIME ALARM  
TUNING  
Press TIME. The alarm indicator begins flashing.  
Press either TUNING button. The time display changes  
slowly at first, then more quickly. It stops when you  
release any button.  
Press TIME to return the display to the current time.  
TIME ALARM  
To change the Alarm 1 sound, press  
.
For tone only, press until the ( ) indicator lights. When  
the alarm goes off, the tone volume gradually increases  
to your preset level.  
For radio only, press until the ( ) indicator lights. When  
the alarm goes off, the radio volume gradually increases  
to your preset level.  
For tone and radio, press until both indicators (  
)
light. When the alarm goes off, the tone sounds. After  
you press SLEEP, the radio turns on.  
Note: You can set the alarm with the radio on or off.  
To set  
Alarm 2  
Press TIME, then  
now have 10 seconds to begin setting Alarm 2.  
. The Alarm 2 indicator flashes. You  
wake up  
time and  
alarm sound  
TIME ALARM  
TIME ALARM  
Note: The Alarm 2 indicator must be flashing while setting  
Alarm 2 wake up time or sound.  
To set Alarm 2 wake up time, press either TUNING button.  
Press TIME to return to the regular display.  
To change Alarm 2 sound, press TIME to return to regular  
display. Then press  
while the Alarm 2 indicator flashes.  
For tone only, press until the ( ) indicator lights. When the  
alarm goes off, the tone volume gradually increases to your  
preset level.  
For radio only, press until the ( ) indicator lights. When the  
alarm goes off, the radio volume gradually increases to your  
preset level.  
For tone and radio, press until both indicators (  
) light.  
When the alarm goes off, the tone sounds. After you press  
SLEEP, the radio turns on.  
Note: The Alarm 2 indicator continues flashing for 10  
seconds after wake up time and sound are set.  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
13  
Clock Functions  
Radio Control Operation  
To use  
Auto Reset  
While the alarm sounds, press ON/OFF once. The alarm  
stops and resets to go off at the same time tomorrow. If you  
do not turn off the alarm, it continues to sound for 30  
minutes. Then it stops and resets to go off at the same time  
tomorrow.  
ON/OFF  
To check  
Alarm 1  
Press ALARM SET. The display shows the wake up time  
for Alarm 1.  
ALARM  
SET  
To check  
Alarm 2  
Simultaneously press both ALARM SET and ALARM MODE.  
The display shows the wake up time for Alarm 2.  
ALARM  
SET  
ALARM MODE  
For the radio ( ), use the VOLUME buttons to set the volume.  
To set the  
volume of  
the alarm  
For tone (  
), choose the alarm sound (see page 12).  
VOLUME  
Set the alarm to go off. When the alarm sounds, press either  
VOLUME button to adjust the volume.  
Press ON/OFF to silence the alarm. This automatically resets  
the alarm to repeat tomorrow.  
ON/OFF  
To snooze  
When the alarm is in tone ( ) or radio ( ) mode, press  
SLEEP/SNOOZE to pause the alarm for ten minutes.  
SLEEP/SNOOZE  
When the alarm is in tone and radio (  
) mode, press  
SLEEP/SNOOZE to pause the tone and hear the radio. The  
tone sounds again in ten minutes. Press again to silence the  
radio. The alarm indicator flashes while paused.  
To stop  
the alarm  
Press ON/OFF once. The indicators remain lit. The alarm  
repeats tomorrow.  
ON/OFF  
To turn off the alarm function, press ALARM MODE until  
To disable  
Alarm 1  
the ( ) and (  
) indicators do not appear on the display.  
ALARM MODE  
The alarm must be reset for next use.  
Hold down ALARM SET and press ALARM MODE. Alarm 2  
flashes on the display. Release ALARM SET. Press ALARM  
To disable  
Alarm 2  
ALARM  
SET  
ALARM MODE  
MODE until the ( ) and (  
) indicators no longer appear.  
To wake to  
your favorite  
station  
Simultaneously press ALARM SET and any PRESET button.  
The preset indicator and the station frequency flash on the  
display.  
ALARM  
SET  
PRESET STATIONS  
Release the ALARM SET button. Alarm 1 plays this station  
until you reset the alarm.  
Alarm  
operation  
during a  
Press ON/OFF to silence. Backup batteries run the alarm  
for approximately a week during power failure. To conserve  
power, only the tone sounds, even if radio is selected. Normal  
operation resumes when power is restored. Batteries should  
be replaced after an extended power failure.  
ON/OFF  
power failure  
14  
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Functions  
Remote Control Operation  
To use  
Auto Reset  
While the alarm sounds, press ON/OFF once. The alarm  
stops and resets to go off at the same time tomorrow. If you  
do not turn off the alarm, it continues to sound for 30  
minutes. Then it stops and resets to go off at the same time  
tomorrow.  
ON/OFF  
Press TIME on your remote control. The display shows the  
wake up time for Alarm 1. Press TIME again to return to  
normal display.  
To check  
Alarm 1  
TIME ALARM  
TIME ALARM  
Press TIME. Then press  
up time for Alarm 2.  
. The display shows the wake  
. The normal display returns.  
To check  
Alarm 2  
Press TIME. Then press  
To set the  
volume of  
the alarm  
For the radio ( ), use the VOLUME buttons to set the volume.  
For tone ( ), choose the alarm sound (see page 13).  
Set the alarm to go off. When alarm sounds, press either  
VOLUME button to adjust the volume.  
VOLUME  
ON/OFF  
Press ON/OFF to silence the alarm. This automatically resets  
the alarm to repeat tomorrow.  
To snooze  
When the alarm is in tone (  
) or radio ( ) mode, press  
SLEEP to pause the alarm for ten minutes.  
SLEEP  
When the alarm is in tone and radio (  
) mode, press  
SLEEP on your remote control to pause the tone and hear the  
radio. The tone sounds again in ten minutes. Press again to  
silence the radio. The alarm indicator flashes while paused.  
To stop  
the alarm  
Press ON/OFF once. The indicators remain lit. The alarm  
repeats tomorrow.  
ON/OFF  
To turn off the alarm function, press  
and ( ) indicators do not appear on the display. The  
alarm must be reset for next use.  
until the (  
)
To disable  
Alarm 1  
TIME ALARM  
Press TIME. Then press  
TIME again. Press  
tors no longer appear on the display.  
. Alarm 2 flashes. Press  
until the ( ) and ( ) indica-  
To disable  
Alarm 2  
TIME ALARM  
To wake to  
your favorite  
station  
Use the radio control panel to select this feature.  
Alarm  
operation  
during a  
Press ON/OFF to silence. Backup batteries run the alarm for  
approximately a week during power failure. To conserve power,  
only the tone sounds, even if radio is selected. Normal opera-  
tion resumes when power is restored. Batteries should be re-  
placed after an extended power failure.  
ON/OFF  
power failure  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
15  
Other Components  
Connecting other components  
Use your Wave® radio to improve the sound of a CD player, cassette player, or TV. You can also  
use your radio as extension speakers for the Bose® Lifestyle® music system. Connect one of these  
components to the right and left AUX IN jacks. Or add powered Bose speakers connected to the  
right and left VARIABLE OUT jacks. Audio cables for these connections are available at electron-  
ics stores, or by calling Bose.  
Most audio cables are color coded. Match the red plugs to the right (red) jack and the black or  
white plugs to the left (white) jack (see Figure 7).  
Connecting components or speakers to the VARIABLE OUT jacks will shut off the radio’s  
speakers.  
Figure 7  
Location of jacks to use in connect-  
ing other components.  
R
AUX IN  
L
120V AC  
50/60Hz 50W  
VARIABLE OUT  
R
AUX IN  
L
Connect red  
plugs here  
Connect white or  
black plugs here  
VARIABLE OUT  
16  
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
Other Components  
Connection at  
component  
Connection at  
Wave® radio  
Note  
Component  
Cable  
One miniplug-to-  
stereo audio cable  
Headphone jack (set  
the headphone volume  
control to 7).  
Portable CD or  
tape player  
AUX IN jacks  
Recording from your Wave radio  
is not recommended because  
connections to the VARIABLE  
OUT jacks shut off the radio  
speakers, preventing you from  
monitoring the recording volume.  
Audio output jacks  
CD player, tape  
deck, or VCR  
One stereo audio  
cable  
AUX IN jacks  
If there are two sets of  
outputs, use the fixed  
outputs.  
Television  
TVs with stereo output  
jacks need a standard  
RCA cord.  
Audio output jacks  
AUX IN jacks  
To make sure the sound seems to  
come from the screen, place the  
Wave radio close to the TV.  
If there are two sets of  
outputs, use the fixed  
outputs.  
TVs with single (mono)  
audio output jacks use  
a standard Y adapter.  
To prevent interference with the TV  
picture, do not place the Wave radio  
directly on top of the TV.  
TVs with earplug outlets  
may need a special  
earplug adapter.  
Bose® Lifestyle®  
music system  
25 to 100 foot stereo  
cable with male-to-  
male RCA plugs.  
TAPE (REC) jacks  
AUX IN jacks  
Powered Bose  
speakers  
Use the audio-input  
cables that came with  
your speakers.  
Speaker system input  
as described in the  
speaker owner’s  
manual.  
VARIABLE OUT jacks  
Some Bose audio-input cables have  
three connectors at each end. Use  
only the two connectors that look  
alike. DO NOT INSERT THE THIRD  
CONNECTOR into the speaker’s  
SYSTEM CONTROL jack.  
Using other components  
Choose your CD player, tape player, or other auxiliary source by pressing the AUX key. Adjust  
the listening volume with the VOLUME keys. Control all other functions at the source, referring  
to its owner’s manual, if necessary. Control your auxiliary powered speakers from the Wave  
radio. If these speakers have a volume control, you may use it.  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
17  
Product Information  
®
Maintaining the Wave radio  
The only necessary maintenance is periodic battery replacement and cleaning.  
Replace the batteries  
To protect your Wave radio’s memory and backup alarm system, replace the batteries every  
year and when you have an extended power loss. Dead batteries may leak and cause damage.  
Do not unplug your Wave radio from the power outlet while replacing the batteries. If you do  
unplug it, you will need to reset the clock, alarm settings, and station presets. For further  
information on replacing batteries, see “Install the batteries” on page 5.  
For information on replacing the remote control battery, see “Install the battery” on page 7.  
How to clean  
Use only a cloth to clean the outside of the Wave radio. Do not use any solvents, chemicals, or  
cleaning solutions containing alcohol, ammonia, or abrasives. Do not allow liquids to spill into  
any openings on the radio. If necessary, you may use a soft-bristled attachment to gently  
vacuum the front of the radio.  
For best radio reception…  
The Wave radio has an internal antenna. You may adjust the antenna by turning the radio  
slightly.  
You may adjust the FM antenna by moving the power cord. If you still have problems with FM  
reception, you may need an external antenna. Call Bose® Customer Service to request one.  
Features  
• Acoustic Wave® speaker technology provides deep, full bass from a small enclosure.  
• High performance stereo tuner allows 6 AM and 6 FM station presets.  
• Automatic protection circuitry prevents speaker damage from excessive volume.  
• Dual independent alarms let you set two wakeup times.  
• Credit card-size remote offers convenient operation of the radio and clock functions.  
Size  
Dimensions  
• 4.5"H x 14"W x 8"D (11.4 x 35.6 x 20.3 cm)  
Weight  
• 7 lb (3.2 kg)  
Power rating  
• USA/Canada: 120VAC~ 50/60 Hz 50W  
18  
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.  
AM189930_01_V.pdf  
®
Bose Corporation  
Warranty period  
The Bose Wave® radio is covered by a limited 1-year transferable warranty. Details of the  
warranty are provided on the warranty card that came with your radio. Please fill out the  
information section on the card and mail it to Bose.  
Customer service  
For additional help in solving problems, contact Bose customer service.  
USA  
1-800-637-8781 Monday through Friday, 8:00 a.m. to 9 p.m. ET  
Canada  
1-800-444-BOSE (1-800-444-2673) Monday through Friday, 9 a.m. to 5 p.m. ET  
AM189930_01_V.pdf  
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.  
19  
Warranty  
© 1996 Bose Corporation  
The Mountain, Framingham, MA 01701-9168 USA  
JN97832 PN189930 Rev.01 AM189930 Rev.01  
 

BenQ Projector W1070 User Manual
Bogen Car Speaker HS7EZ User Manual
Bosch Power Tools Trimmer ART EASYTRIM Accu NIMH User Manual
Boston Acoustics Music Mixer VRI595 User Manual
Broan Range 463002 User Manual
Bushnell Telescope 78 7846 User Manual
Cadco Toaster CBF 4M User Manual
Canon All in One Printer 5293B002 User Manual
Chamberlain Universal Remote 956D User Manual
Cisco Systems Network Card CE 100T 8 User Manual