Breville Water Dispenser AF5 User Manual

Aqua Fountain  
Instructions for Use  
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
These instructions refer to the Breville Water Filter/Chillers AF5 and AF6  
 
FEATURES  
Fig 1  
q
w
e
r
s
t
y
u
i
o
a
1. BRITA Memo - cartridge exchange  
indicator  
6. ON/OFF switch  
7. Red power on indicator  
8. Chilled water indicator  
9. Water dispenser lever  
2. Upper water tank cover  
3. Hinged lid  
4. 1 litre upper water tank  
5. 2 litre filtered water tank  
10. 1 litre chilled filtered water tank  
11. BRITAMAXTRAwater filter  
3
 
BEFOREUSINGYOURWATERFILTER/CHILLER  
Before using your water filter/chiller for  
the first time, it is recommended that the  
unit is flushed through with fresh water.  
Pleaseensurethatyoureadthefollowing  
instructions before flushing your water  
filter/chiller several times.  
5. Position the water filter/chiller on a  
stable flat surface, close to a mains  
power socket, not in direct sunlight  
and out of the reach of children.  
6. Make sure that there is sufficient  
space around the water filter/chiller  
to allow the heat extracted during  
the chilling process to dissipate.  
Leave a gap of at least 15 cm  
between the ventilation slots on the  
rear of the chiller and any wall or  
surface.  
1. Remove your water filter/chiller  
carefully from the box. You may wish  
to store the packaging for future use.  
2. Check the contents:  
Water filter/chiller  
BRITAMAXTRAwater filter cartridge  
User guide  
Do not plug the unit in or install the  
filter cartridge yet.  
7. Lift the hinged lid and using a  
suitable jug, pour 2 litres of clean  
water into the tank. Place a glass  
under the dispenser and push the  
dispensing lever back to drain all of  
the water. It may take some time for  
the water to initially flow through.  
BRITA brochure  
BRITA registration card  
3. Wash the clear plastic lid, upper and  
filtered water tanks in warm soapy  
water, rinse and dry thoroughly.  
4. Reassemble the tanks as shown  
below.  
8. Repeat this process one more time.  
Upper water tank  
cover  
Upper water tank  
Filtered water  
tank  
Chilled and filtered  
water tank  
4
 
PREPARINGTHEFILTERCARTRIDGE  
1. Remove the cartridge from its  
1. Place the upper tank on a suitable  
bowl or jug. Fill with cold tap water  
up to the MAX FILL LEVEL mark on  
the upper water tank and allow the  
water to filter through.  
wrapping (it is normal for the cartridge  
to appear moist during storage - this  
is simply condensation).  
2. Immerse the cartridge in cold water  
and agitate gently to remove any air  
bubbles.  
Maximum fill level mark  
NOTE  
There is no need to pre-soak this  
cartridge before use.  
Discard the first two fillings. These  
first two fillings are used to flush the  
filter cartridge. Place the upper tank  
back into the unit.  
3. Remove the lid from the upper water  
tank.  
4. Insert the filter cartridge into the water  
tank as shown below. Push it firmly  
into place. When correctly fitted, the  
cartridge should remain in place  
when the tank is turned upside down.  
2. Replace the upper water tank lid.  
3. Press and hold the START button on  
the BRITA Memo on the lid until all of  
the bars on the display appear and  
flash twice, see “Using the Memo  
function” on page 8.  
NOTE  
When it is time to replace the cartridge  
after 4 weeks use, simply lift the ring  
pull handle on top of the cartridge to  
remove. The cartridge may be  
disposed of in household waste or  
contact the BRITA-Care customer  
service for advice on recycling  
schemes.  
5
 
USINGYOURWATERFILTER/CHILLER  
1. Lift the hinged lid and using a  
4. Plug the unit into the mains supply.  
Press the chiller ON/OFF switch on  
the front of the unit. The switch will  
illuminate and the machine will begin  
to chill the water.  
suitable jug, carefully pour water into  
the tank up to the MAX FILL LEVEL.  
This may take some time due to the  
action of the filter.  
5. Dispense 2 litres of water from the  
unit to remove any unfiltered water  
from the unit that was used to prepare  
the chiller as instructed on page 4.  
6. Within approximately 3 hours the blue  
indicator on the front of the unit will  
light indicating that the water has  
chilled to approximately 10OC,  
although this may take longer in very  
hot weather. The indicator will cycle  
on and off as the unit maintains its  
temperature, but the unit will continue  
to chill the water down to 8OC then  
stop. If the water temperature rises  
above 8OC the unit will start to chill  
again.  
2. Keep adding water until all the tanks  
are full. Water flows through the  
cartridge at a set rate. This is to  
achieve the best possible filtration.  
Because of this it may take some time  
to fill all the tanks on first use. During  
normal use top up the tanks regularly.  
We recommend that the water chiller  
bekeptoutofdirectsunlightandaway  
from any heat source.  
7. Place a glass under the dispenser  
and push the lever back to dispense  
water.  
NOTE  
After filling, it is important to vent any  
air in the unit otherwise the chiller will  
not function correctly. Do this by  
pressing the dispensing lever until  
the water flows from the dispenser  
without any air bubbles present. Once  
the water is clear of any air bubbles,  
the dispensing lever may be released.  
Top up the water tank if necessary.  
NOTE  
It is normal for the indicator to go off  
when water is drawn. Water inside  
the unit will remain chilled but the  
indicator will not come on again until  
the optimum temperature has been  
reached.  
3. Close the hinged lid.  
8. Top up the water tank as necessary.  
6
 
USINGYOURWATERFILTER/CHILLER  
For optimum enjoyment, we recommend  
NOTE  
that if your water chiller has not been  
used for 1 day or more, you first draw half  
a glass of water and dispose of it. It is  
possible to use the unit without power  
but the water will not be chilled.  
Remember that water is a foodstuff.  
Please consume filtered water within 2  
days.  
There is a risk of leakage from the  
split joint between the top tank and  
filtered water tank. This may occur if  
the unit is moved or disturbed when  
both tanks are at maximum capacity.  
Toavoidleakage, drawoffwaterusing  
the lever to empty the top tank so that  
it does not overflow when moved.  
To empty filtered water from the system,  
use the plug in the base of the chiller as  
instructed in the storage section on page  
10.  
Troubleshooting  
Water is not dispensed:  
When replacing the bottom 2 litre filtered  
water tank, please ensure that there is  
no water in the inner well (illustrated  
below).  
Make sure that there is water in the  
tank.  
Air trapped in the filter cartridge may  
stop water flowing into the filtered  
water tank. The cartridge must be  
immersed in cold water and agitated  
to removed any air bubbles before  
installation.  
Inner well  
Filter is blocked. Replace.  
Air can become trapped in the  
internal tank. Press the dispensing  
lever until clear water dispenses  
without any air bubbles. This may  
take some time.  
Chiller light tuning off and on:  
If there is water present, dispense the  
water using the lever until the well is  
empty.  
The chiller light will not stay on  
permanently. It will cycle on and off  
as the temperature of the water is  
maintained.  
Should water spill from the tank it is not  
dangerous. Do not grasp or pull on the  
tank sections to move or reposition the  
unit.  
7
 
USINGTHEBRITAMEMOFUNCTION  
It is important to change your BRITA  
water filter cartridge regularly to enjoy  
the benefits of BRITA filtered water. The  
BRITA Memo system automatically  
reminds you when your water filter  
cartridge needs to be changed.  
%
100  
75  
50  
When you have fitted and prepared your  
water filter cartridge, start the Memo  
system as follows:  
25  
Press and hold the start button until  
four bars appear in the display and  
flash twice. The Memo is now set.  
The flashing dot in the bottom right  
corner of the display will show that  
the Memo is working.  
Every week one bar will disappear to  
indicate the remaining cartridge life.  
When only one bar is showing, check  
that you have a replacement BRITA  
MAXTRA water filter cartridge  
available.  
%
100  
75  
50  
25  
After four weeks, all four bars will  
disappear and a flashing arrow will  
appear to indicate that the filter  
cartridge should be replaced.  
Insert a new BRITA water filter  
cartridge (as described under  
“Changing the BRITA MAXTRA Filter  
Cartridge” on page 9) and restart the  
Memo as described above.  
Please note: The Memo system is only  
intended for use with BRITA filter  
cartridges.  
8
 
CHANGINGTHEBRITAMAXTRAFILTERCARTRIDGE  
The filter cartridge will need to be  
changed approximately once per month.  
7. Follow the instructions in “Preparing  
the Filter Cartridge” on page 5.  
1. Switch the water filter/chiller off and  
disconnect from the mains supply.  
8. Insert the BRITA MAXTRA filter  
cartridge into its receptacle in the  
upper water tank.  
2. Using the dispenser, (as described  
in Cleaning and Maintenance on  
page 10) completely drain the water  
from the tanks.  
9. Replace the upper water tank lid.  
10. Restart the BRITA Memo system as  
described in “Using the BRITA Memo  
Function” on page 8.  
3. Remove the upper water tank cover.  
4. Pull the BRITAMAXTRAfilter cartridge  
out of the unit and discard it.  
11. Lift the hinged lid and refill the tanks.  
12. Close the hinged lid.  
5. Wash the lid and tanks in warm  
soapy water, rinse and dry thoroughly.  
13. Plug the unit into the mains and press  
the chiller ON/OFF switch on the front  
of the unit and wait for the water to  
chill.  
6. Remove the new BRITAMAXTRAfilter  
cartridge from its wrapping.  
NOTE  
NOTE  
Always make sure you have spare  
cartridges to hand. When buying  
cartridgeslookfortheBRITAMAXTRA  
symbol on the cartridge packaging to  
find the correct filter cartridge in store.  
The cartridge and inside wrapper may  
be moist - this is simply condensation.  
9
 
CLEANINGANDMAINTENANCE  
9. To flush through the system pour  
Cleaning  
approximately 2 litres of water into  
the tank, depress the dispensing  
lever until water starts to come out of  
the dispensing nozzle, and then  
empty using the drain plug at the  
bottom of the unit over a sink or large  
container. Replace the drain plug.  
Theoutercasingofyourwaterfilterchiller  
can be cleaned using a soft damp cloth  
and a non-abrasive cleaner.  
It is important that the inside of the chiller  
is cleaned regularly. We recommend  
that this is done at least monthly e.g.  
whenchangingtheMaxtracartridge.Also,  
ensure that the dispensing nozzle is  
cleaned regularly.  
10. Your chiller is now ready to use. Fill  
the chiller tanks with tap water as per  
chiller instructions, plug the unit into  
the socket and turn on. Use the chiller  
as normal.  
Cleaning Instructions  
1. Disconnect the chiller from the  
electrical socket and drain all the  
water by unscrewing the drain plug  
on the bottom of the unit over a sink  
or large container.  
Storage  
Ifyouarenotgoingtouseyourwaterfilter  
chiller for an extended time disconnect  
the unit from the mains and drain the  
water using the drain plug at the bottom  
of the unit over a sink or large container.  
2. When empty of water replace the  
drain plug.  
3. Remove the lid and top up the water  
tank, leaving the bottom water tank  
in place.  
Remove the filter cartridge and discard.  
Leave the lid off and allow the unit to dry  
thoroughly.  
4. Pour approximately 2 litres of water  
into the bottom tank, and add a non-  
tainting sterilising fluid such as Milton  
(following manufacturer’s guidelines  
for dilution).  
If the chiller has not been used for an  
extended time, follow the internal  
cleaning instructions above before  
reusing.  
5. Depress dispensing lever until fluid  
starts to come out of the dispensing  
nozzle.  
6. Stop depressing the lever when the  
fluid comes through the nozzle.  
7. Leave the fluid to stand in the chiller  
as recommended by the fluid  
manufacturers instructions (normally  
approximately 10/15 minutes).  
8. Drain the chiller using the drain plug  
at the bottom of the unit over a sink or  
large container. Replace the drain  
plug.  
Drain Plug  
10  
 
IMPORTANTSAFETYINSTRUCTIONS  
Always ensure hands are dry before  
handling the plug or switching on the  
appliance.  
Always use the appliance on a  
secure, dry level surface.  
Always unwind the power cord before  
use.  
Never use this appliance outdoors.  
Never use this appliance for other  
than the intended use. This appliance  
is for household use only.  
Never immerse any part of the  
appliance, cordset or plug in water or  
any other liquid to protect against  
electrical hazards.  
Never use harsh, abrasive or caustic  
cleaners to clean this appliance.  
Never let the cable hang over the edge  
of the worktop, touch hot surfaces or  
become knotted.  
Never place this appliance on or near  
a hot gas or electric burner or where it  
could touch a heated oven or microwave  
oven.  
Never operate any appliance with a  
damaged cable or plug or after an  
appliance malfunction or if it has been  
damaged in any manner.  
Never keep the appliance in an  
environment below 0oC. Water in the unit  
will freeze and cause damage.  
Never use any attachment or  
accessory not supplied with the  
appliance or not recommended by the  
appliance manufacturer.  
Always carry out regular checks of  
the supply cord to ensure no damage  
is evident. Should there be any signs  
that the cord is damaged in the slightest  
degree, the entire appliance should be  
returned to the Customer Service  
Department.  
Always allow 15 cm of air space  
above and on all sides for air circulation.  
Do not allow the appliance to touch  
curtains, wall coverings, clothing,  
dishtowels or other flammable  
materials during use.  
Always use BRITA MAXTRA water  
filter cartidges.  
Always unplug the appliance from the  
mains power supply socket before filling  
with water, after use, and before  
cleaning.  
Always return the appliance after a  
malfunction, or if it has been damaged  
in any manner to the Customer Service  
Department for examination, repair or  
adjustment as special purpose tools  
are required.  
Always ensure that the filter is  
securely positioned.  
Always reset the BRITA Memo after  
changing the filter.  
Never fill the water tank with any liquid  
other than water.  
Never use the water filter/chiller  
without a water filter cartridge fitted. The  
Breville water filter/chiller is designed  
to be used with the BRITA MAXTRAfilter  
cartridge.  
Never attempt to filter untreated, raw  
water or water of unknown quality. This  
water filter cartridge must only be used  
with municipally treated tap water.  
Always Remember that water is a  
foodstuff. Please consume filtered water  
within 2 days. To empty filtered water  
form the unit please use plug in the  
base of chiller as instructed in the  
storage section on page 10.  
Always Clean the inside and  
dispenser of the chiller at least every 2-  
3 weeks.  
11  
 
CONNECTION TO THE MAINS SUPPLY  
When using electrical appliances, basic safety precautions should always be  
followed.  
! WARNING  
THIS APPLIANCE MUST BE EARTHED  
If this appliance is fitted with a rewirable BS1363, 13 amp plug, the fuse should be  
rated at 3 amps and be ASTA approved to BS1362. However if the plug is unsuitable,  
it should be dismantled and removed from the supply cord and an appropriate plug  
fitted as detailed below.  
If this appliance is fitted with a moulded BS1363 13 amp plug, the fuse should be  
rated at 3 amps and be ASTA approved to BS1362. If the fuse in a non-rewirable plug  
needs to be changed, the fuse cover must be refitted. The appliance must not be  
used without the fuse cover fitted.  
In the event of the plug being unsuitable, it should be changed and an appropriate  
plug fitted as detailed below. If you remove the plug it must not be connected to a 13  
amp socket and the plug must be disposed of immediately.  
As the colours of the wires in the mains lead of this appliance may not correspond  
with the coloured markings identifying the terminals in your plug, proceed as follows:  
The wires of the mains lead are coloured in accordance with the following code:  
GREEN & YELLOW = EARTH  
BLUE = NEUTRAL  
BROWN = LIVE  
The wire which is coloured GREEN & YELLOW must be connected to the terminal  
in your plug which is marked with an E or by the EARTH SYMBOL  
or coloured  
GREENorGREEN&YELLOW.  
ThewirewhichiscolouredBLUE  
Plug should be BS1363/A approved  
Fit a 3 Amp fuse  
must be connected to the  
terminal in your plug which is  
marked with the letter N or  
colouredBLACK.  
3 Amp  
fuse  
The wire which is coloured  
BROWN must be connected to  
the terminal in your plug which  
is marked with the letter L or  
coloured RED.  
BLUE  
(Neutral)  
BROWN  
(Live)  
Ifanyotherplugisused, a3amp  
fuse must be fitted either in the  
plug or adaptor or at the  
distributor board.  
Ensure that the outer sheath of the cable  
is firmly held by the clamp  
12  
 
AFTER SALES SERVICE  
These appliances are built to the very highest of standards. There are no user-  
serviceable parts. Follow these steps if the unit fails to operate:  
1
2
3
Check instructions have been followed correctly.  
Check fuse has not blown.  
Check mains supply is functional.  
If the appliance will still not operate, return the appliance to the place it was  
purchased for a replacement. To return the appliance to the Customer Service  
Department, follow the steps below:  
1. Pack it carefully (preferably in the original carton). Ensure unit is clean.  
2. Enclose your name and address and quote model number AF7 on all  
correspondence.  
3. Give the reason why you are returning it.  
4. If within the guarantee period, state when and where it was purchased and  
include proof of purchase (eg. till receipt).  
5. Send it to our Customer Service Department at the address below:  
Customer Service Department  
Pulse Home Products Limited  
Vine Mill, Middleton Road,  
Royton,  
Oldham  
OL2 5LN, UK.  
Telephone: 0161 621 6900 Fax: 0161 626 0391  
6. For BRITA/MAXTRAwater filter cartridge and BRITAMemo queries, contact BRITA  
Customer Care Services on:  
Telephone: 0870 487 1000  
13  
 
GUARANTEE  
This product is guaranteed for a period of 1 year from the date of purchase against  
mechanical and electrical defects.  
This guarantee is only valid if the appliance is used solely for domestic purposes  
in accordance with the instructions provided, that it is not connected to an unsuitable  
electricity supply, dismantled or interfered with in any way or damaged through  
misuse. Under this guarantee we undertake to repair or replace free of charge any  
parts found to be defective.  
Nothing in this guarantee or the instructions relating to the product excludes, restricts  
or otherwise affects your statutory rights.  
In line with our policy of continuous development, we reserve the right to change this  
product, packaging and documentation without notice.  
This product is manufactured to comply with the radio interference requirements of  
EEC directive 93/68 EEC.  
14  
 
RECYCLING INFORMATION  
The Maxtra cartridge in the chiller is 100% recyclable. Look out for BRITA recycling  
points in major retailers or visit www.brita.co.uk for more information.  
Waste Electrical and Electronic Equipment (WEEE)  
WEEE is the fastest growing waste stream in the UK, growing by at least 5% each  
year. The UK public alone dispose of over 1.2 million tonnes of electrical and  
electronic waste every year; this would fill the new Wembley Stadium 6 times over.  
Much of the UK’s electronic waste ends up in landfill sites. It has been estimated  
that landfill space in the UK will run out within the next 10 years if we do not increase  
the amount of waste we recycle.  
WEEE that is not recycled can have negative impacts on soil, air and water quality  
which can lead to environmental damage and which can also lead to negative  
impacts on human and animal health.  
Recycling household electrical equipment – regulations  
With effect from July 2007, the UK’s Waste electrical and Electronic Equipment  
(WEEE) Regulation require that all producers of electrical equipment are now  
obliged to pay for recycling of household electrical goods, where previously this bill  
was met by councils or items were not recycled at all. These regulations also require  
that all retailers both actively assist in delivering a UK wide WEEE collection  
infrastructure and encourage the participation of consumers in recycling electronic  
equipment.  
So that you can get your waste electrical goods recycled, we have contributed  
towards a national fund to assist local councils to further develop their existing waste  
electronics collection facilities, which will in turn allow producers of this equipment  
to meet their obligations.  
15  
 
RECYCLING INFORMATION  
The Crossed out Wheeled Bin Symbol  
All new electrical and electronic equipment should be marked with the crossed out  
wheeled bin, which aims to encourage you to separate out WEEE from other  
household waste and to dispose of it at a recycling facility.  
recycle-more.co.uk  
For advice on all aspects of recycling, to find out how to minimise your effect on the  
environment and locate your nearest recycling facilities for electronic waste please  
visit www.recycle-more.co.uk and use the recycle-more bank locator.  
Recycle-more.co.uk also offers top tip and advice on all aspects of recycling, making  
it easier and quicker to protect our environment and recycle-more!  
16  
 
17  
 
18  
 
19  
 
Vine Mill, Middleton Road, Royton, Oldham, OL2 5LN, UK.  
Breville is a registered trademark of Pulse Home Products Limited  
© Pulse Home Products Limited  
92423-6  
AF5_6_Iss_8 02/08  
 

Belkin Computer Drive F5U252ea User Manual
Bissell Vacuum Cleaner 37N1 User Manual
Black Decker Blender BLM2600G User Manual
Blue Rhino Charcoal Grill GBC981W User Manual
Bolens Chipper 452 Thru 465 User Manual
Brother Fax Machine 2440C User Manual
Browning Outboard Motor OtN Series 2000 User Manual
Casio Digital Camera EX Z1 User Manual
Chromalox Thermostat 3001E User Manual
Cisco Systems IP Phone OL 9531 01 User Manual