CDA Refrigerator FW820 User Manual

FW820 extra large integrated  
larder fridge  
Manual for Installation, Use and Maintenance  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 
Before first use  
You must allow the fridge to settle for at least twenty four hours prior to switching the power on.  
It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda  
and warm water and then thoroughly drying the interior.  
The fridge may have an odour to it at first use. This will disappear as the appliance cools.  
Do not load the fridge with food until at least 2 hors have passed and the fridge is closed to correct temperature.  
Please note:  
The appliance will work continuously until it comes down to the correct temperature.  
If the appliance is switched off, you should allow five minutes before switching it on again to prevent unnecessary  
damage to the compressor.  
Defrosting the fridge  
The fridge is self-defrosting. Any water created will run out of the fridge through the channel at the back of the fridge.  
It is important to keep the channel clear at all times. The defrosted water is collected in the evaporating tray at the back  
of the appliance.  
fig. 1  
Use  
Never put liquids in the refrigerator uncovered.  
Never put hot foods in the refrigerator. Warm food should be allowed to cool to room temperature before being  
put into the refrigerator.  
Nothing should rest against the internal rear wall of the refrigerator, as this will cause frost and possible  
condensation problems which will be difficult to remove.  
Setting the temperature  
You must allow the fridge to settle for at least twenty four hours prior to switching the power on.  
The fridge will take some time to adjust to the new settings. This will depend on the difference between the old ad new  
settings, the ambient temperature, the amount of food in the fridge and the number of times the door is opened.  
To adjust the temperature turn the thermostat control knob clockwise (from off) to the required level. The temperature  
becomes colder the higher the number on the control.  
 
Care and cleaning  
Always disconnect the appliance from the power before any cleaning or maintenance.  
The refrigerator should be cleaned using a solution of bicarbonate of soda and lukewarm water.  
Do not use abrasive products or detergents. After washing, rinse and dry thoroughly.  
Clean the shelves and balconies separately by hand using soap and water. Do not put them in the dishwasher.  
The evaporating tray and water drain hole (at the back of the compartment) should be cleaned  
periodically to prevent the defrosted water from collecting inside the compartment. The drain  
plug can be used to clear the drain hole.  
Once cleaning is complete, reconnect the mains power supply.  
If the appliance is not used for prolonged periods of time or in the event of a prolonged power cut unplug and clean  
the appliance. The doors should be left slightly open to prevent the formation of mildew and smell.  
The door sea soul be cleaned periodically.  
Clean the switch, lamp and thermostat control with a dry cloth.  
Changing the light bulb  
Disconnect the appliance from the power.  
Remove the light cover.  
Replace the light cover and reconnect the power after five minutes’ delay as explained on page 3.  
 
Troubleshooting  
If you have any problems with your appliance, you should check the troubleshooting prior to calling CDA Customer Care  
to prevent unnecessary service calls and potential cost.  
If the appliance is not working  
Check there is power to the appliance.  
The house fuses are intact and the fuse in the plug has not blown.  
The thermostat is not set to 0 (off position).  
The plug socket is functioning fine. To check this, plug another electrical appliance in to see if the socket is working.  
The temperature of the room is adequate (10oC or above).  
If the appliance is working, but not very well  
The appliance is not overloaded.  
The thermostat is set to an appropriate temperature.  
The door is closing properly.  
The cooling system at the rear of the appliance is clean and free of dust, and not touching the rear wall.  
There is enough ventilation at the side and rear walls.  
The temperature of the room is adequate (10oC or above).  
If the appliance is noisy  
The appliance is level and stable.  
The side and rear walls are clear, and there is nothing resting on the appliance.  
The cooling gas in the refrigerator will make a slight bubbling noise, even when the compressor is not running.  
If there is water in the lower part of the refrigerator compartment  
The drain hole in the channel at the back of the compartment is clear.  
 
Installation And Ventilation  
This appliance must never be installed close to heat sources i.e. heating  
elements, cookers or in damp places  
The diagram shows the ventilation requirements for your product.  
Failure to provide adequate ventilation can lead to increased running costs and  
premature failure and may invalidate the warranty provided with the product.  
540  
1780-1783  
540  
fig. 2  
 
Reversing the door  
fig. 3  
It is possible to reverse the door on this appliance, if required.  
To do so, follow the steps below:  
1. Loosen the top hinge fixing screws and remove the top hinge,  
taking care to support the weight of the door.  
2. Lift the door from the bottom hinge and place on a soft surface  
to protect the door from damage.  
3. Refit the hinge taken from the top to the opposite lower corner,  
as in figure 3.  
4. Replace the door and refit the hinge taken from the lower corner  
to the opposite top corner.  
5. Adjust the hinges to ensure the door is aligned correctly.  
 
Mounting the Fascia Door  
x4  
Using a screwdriver, x the mounting brackets to the •  
appliance door, as shown in figure 4.  
Position the appliance within the unit. Ensure that there  
is a gap of 3 to 4 mm between the non-hinged side and  
the cabinet wall.  
Locate the slider in the bracket and fix the slider to  
the fascia door 20 to 22 mm from the edge of the  
fascia as shown in figure 5, ensuring that the slider is  
positioned centrally and horizontally within the bracket.  
Tighten securely by hand.  
Fill the gap on the non-hinged side with the seal strip •  
provided, as shown in figure 6.  
fig. 4  
x4  
20 mm  
fig. 5  
door gasket  
fig. 6  
 
Electrical information  
Warning! This appliance must be earthed.  
The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug,  
follow the steps below:  
1. Remove the fuse cover and fuse.  
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.  
3. Replace fuse cover.  
Important: Do not use the appliance without the fuse cover in position.  
How to connect an alternative plug  
If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid possible shock  
hazard. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.  
As the colours of the wires in the mains lead of this appliance may not correspond with the  
coloured markings identifying the terminals in your plug, proceed as follows:-  
The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or  
by the Earth symbol or coloured GREEN and YELLOW.  
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or  
coloured BLACK.  
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or  
coloured RED.  
If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the  
supply cable, the appliance may require removing for servicing.  
N.B. Ensure that the plug socket is situated in an easily accessible place.  
 
 
 
To contact our Customer Care Department, or for Service,  
please contact us on the details below.  
Customer Care Department • The  
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY  
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu  
 

Belkin Switch F1U119 User Manual
Bionaire Air Cleaner BAP1400 User Manual
Blanco Indoor Furnishings 513 688 User Manual
Blaupunkt MP3 Player Compact Drive MP3 User Manual
Bolens Lawn Mower 112 310A User Manual
Bosch Appliances Home Security System DVAS User Manual
Brinkmann Landscape Lighting 822 0408 0 User Manual
Brother Fax Machine FAX 1000 User Manual
Campbell Hausfeld Air Compressor FP260100 User Manual
Carrier Fan 38AK007 User Manual