SPK-SHOWER
showerPOD 900MHz Wireless Shower Speaker
USER MANUAL
Parts Identification
Transmitter
Receiver
Adapter
Transmitter Operation
1. Plug the included AC adapter into a standard wall outlet
2. Turn on the power switch on rear transmitter. A blue indicator flashes
when the AC adapter is plugged in. If the blue POWER indicator does
not illuminate, ensure the adapter is plugged in.
3. Insert the adapter connector plug firmly into the DC jack located at the
back of the transmitter
4. You can pull out a 3.5mm audio cable in front of the transmitter, which
you can connect it to the i-pod’s output jack. After used, just pull it for a
bit and release, then it will roll back automatically
5. The rubber surface of the transmitter is specially designed for you to lay
your I-pod on it to prevent sliding down
6. You can also connect the 3.5mm audio cable to the other end to the
output jack of any of your desired audio sources, like MP3, CD, DVD,
TV, Radio recorder, etc.
7. When an audio signal reaches the transmitter, the Blue indicator
illuminates steady. If the Blue indicator keeps flashing, ensure the audio
source is switched on
Speaker
Battery Operation
1. To operate the speaker using battery power, open the battery
compartment cover located at the rear of the speaker
2. Insert six AA size batteries (purchase separately) into the battery
compartment, observing proper +/- polarities as indicated
3. Replace the battery compartment cover
AC Operation
1. To operate the speaker using AC power, plug the 9V power adapter into
a standard wall outlet
2. To insert the power adapter connector plugs firmly into the DC IN jacks
located underneath the speaker
Speaker Operation
1. To switch on the speaker, press the POWER button located on the front
panel of the speaker. A blue power LED on the speaker illuminates
2. To listen to a desired audio source through the speaker, switch on the
audio device that the transmitter base is connected to. The blue LED on
the transmitter illuminates steady
3. Depending on location, select CHANNEL 1 or 2 on the transmitter base
for optimal performance
4. To locate the strongest operating frequency, press the AUTO TUNE
button located on the front speaker panel. When the Auto Tune function
is engaged, frequency scanning begins automatically and stops when a
signal is detected.
5. You should experience interference-free speaker reception during
normal room to room operation. If interference or poor signal reception
occurs, press the AUTO TUNE button located on the speaker once (the
blue LED indicator illuminates) to locate the strongest operating
frequency.
6. If peak reception remains elusive, switch the CHANNEL setting (1 or 2)
on the transmitter base, then press the AUTO TUNE button on the
speaker to locate the corresponding frequency
7. “The BASS BOOST button can be used to enhance the bass sound
depending on your music preferences. Turn bass / boost effect ON
simply by pressing the button down on the speaker, and pressing it
once again to turn it OFF.“
8. To suit the needs of different users, you can mount the speaker inside
your bathroom
Speaker Operation
Note:
When transmitting over long distances, the audio signal becomes weaker
and interference increases.
If the source signal is too weak for reception, the transmitter automatically
switches off, blue indicator will flash after approximately four minutes to
protect the unit and save power. If the source signal returns to an adequate
level, the transmitter automatically switches back on.
Power Off
To switch off power, press the ON/OFF button on the front panel of the
speaker. And then slide power switch to “OFF” position at rear transmitter.
Volume Control
To adjust speaker sound level, press the +/- buttons located on the front
panel of speaker until the desired volume is reached.
This device must be used with the AC/DC adapter supplied in the
package.
Troubleshooting
No Sound
-
Ensure the AC adapter is securely plugged into the wall outlet and the
transmitter DC IN jack
-
-
Ensure the speaker POWER button is in the ON position
Speaker batteries may be too weak. Replace with new batteries or connect
with the AC/DC adapter (Included)
-
-
Ensure the connected audio device is switched on and producing a signal.
Ensure that the volume level is set to a moderate level
Distortion
-
-
-
Ensure the speaker and transmitter are operating on the same frequency. If
not, press the AUTO TUNE button until both units are operating on the
same frequency
Switch the CHANNEL selector position (1 or 2) on the transmitter base and
press the AUTO TUNE button the speaker until the matching frequency is
reached
Speaker batteries may be too weak. Replace with new batteries or connect
with the AC/DC adapter (not supplied)
-
-
Ensure that the volume level is set to a moderate level
The audio signal input level is too low. Increase the volume level of the
audio source
Specifications
Transmission Mode: UHF mono
Carrier Frequency: 900MHz Digital Hybrid
Operation Voltage: Transmitter, DC 12V 200mA adapter
Speaker, 6 x AA batteries (not supplied) or DC 9V 500mA
adapter (included)
Frequency Response: 40Hz - 12KHz
Distortion: 1%
S/N Ratio: 70dB
Operating Distance: Up to 150 feet
Package includes:
Wireless shower speaker x 1
Audio transmitter x 1
AC/DC power adapters x 2
6.3mm to 3.5mm stereo adapter x 1
User manual x 1
ATTENTION:
The transmitter for this speaker set is designed to work with a wide
variety of devices. Our tests have shown the default volume levels of
iPods, MP3 players and other devices connected to the transmitter
through the headphone jack does not have the signal strength required
by the transmitter. Raising the volume of your device will increase the
signal strength to the transmitter. The blue signal LED will light when the
required signal strength from your device is reached. We recommend
that you keep the volume set on your iPod or MP3 player at a minimum of
¾ of full volume.
|