VHSIM-G02
User’s Guide
VHSIM-G02
1
2
9034001
Only qualified personnel should perform installation
procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867
1999 by Cabletron Systems, Inc.
All Rights Reserved
Printed in the United States of America
Order Number: 9034001 October 1999
Cabletron Systems and LANVIEW are registered trademarks and SmartSwitch is a trademark of
Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
VHSIM-G02 User’s Guide
i
Notice
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
ii
VHSIM-G02 User’s Guide
Notice
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron
software program (“Program”) in the package. The Program may be contained in firmware, chips or
other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON ORYOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE
OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
VHSIM-G02 User’s Guide
iii
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
iv
VHSIM-G02 User’s Guide
Notice
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED
STATES OF AMERICA AND BY UNITED STATES OF AMERICA
GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems
Sales and Service, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the
laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
VHSIM-G02 User’s Guide
v
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
vi
VHSIM-G02 User’s Guide
Notice
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE
FOLLOWING GEOGRAPHICAL REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,
CAREFULLY READ THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron
Systems Limited (“Cabletron”) that sets forth your rights and obligations with respect to the
Cabletron software program (“Program”) in the package. The Program may be contained in firmware,
chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO
BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS
FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON
SYSTEMS +1-603-332-9400. Attn: Legal Department.
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3.
APPLICABLE LAW. This License Agreement shall be governed in accordance with English
law. The English courts shall have exclusive jurisdiction in the event of any disputes.
4.
EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to
regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which
prohibit export or diversion of certain technical products to certain countries, unless a license to export
the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under
the U.S. Export Administration Regulations, You agree that You are a civil end user of the Program
and agree that You will use the Program for civil end uses only and not for military purposes.
VHSIM-G02 User’s Guide
vii
Notice
If the Program is exported from the United States pursuant to the License Exception TSR under
the U.S. Export Administration Regulations, in addition to the restriction on transfer set forth in
Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the Program, the source
code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania,
Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan,
Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other
countries as may be designated by the United States Government), (ii) export to Country Groups D:1
or E:2 (as defined herein) the direct product of the Program or the technology, if such foreign
produced direct product is subject to national security controls as identified on the U.S. Commerce
Control List, or (iii) if the direct product of the technology is a complete plant o r any major
component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as
identified on the U.S. Commerce Control List or is subject to State Department controls under the
U.S. Munitions List.
5.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i)
was developed solely at private expense; (ii) contains “restricted computer software” submitted with
restricted rights in accordance with section 52.227-19 (a) through (d) of the Commercial Computer
Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data
belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product is considered
commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and
use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its
documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING
WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE
USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED
WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY
NOT APPLY TO YOU.
viii
VHSIM-G02 User’s Guide
Notice
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a
Commercial or Light Industrial
Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged
with this notice conforms to the above directives.
Manufacturer
Legal Representative in Europe
Mr. Ronald Fotino
Mr. J. Solari
___________________________________
___________________________________
Full Name
Full Name
Compliance Engineering Manager
Managing Director - E.M.E.A.
___________________________________
___________________________________
Title
Title
Rochester, NH, USA
Newbury, Berkshire, England
___________________________________
___________________________________
Location
Location
VHSIM-G02 User’s Guide
ix
Notice
x
VHSIM-G02 User’s Guide
FIGURES ............................................................................................... xiii
TABLES.................................................................................................xiv
CHAPTER 1
INTRODUCTION
1.1 Structure of this Guide................................................................. 1-2
1.2 Overview...................................................................................... 1-2
1.5 Getting Help................................................................................. 1-4
CHAPTER 2
2.2.1 Installing the VHSIM-G02 in an Interface Module........... 2-2
2.3 Network Connections .................................................................. 2-7
CHAPTER 3
LANVIEW LEDs
3.2 Redundancy ................................................................................ 3-2
CHAPTER 4
4.1 Requirements .............................................................................. 4-1
4.2 Gigabit Port Mode........................................................................ 4-1
APPENDIX A
VHSIM-G02 SPECIFICATIONS
A.1 Physical and Environmental Specifications.................................A-1
A.2 Regulatory Compliance ...............................................................A-1
A.3 Gigabit Port Pin Assignments......................................................A-2
VHSIM-G02 User’s Guide
xi
Contents
xii
VHSIM-G02 User’s Guide
Figure
Page
1-1
2-1
2-2
2-3
3-1
VHSIM-G02.............................................................................. 1-1
Removing the VHSIM Coverplate from the Host Platform ....... 2-3
Installing the VHSIM-G02 in the Host Platform ........................ 2-4
Connecting a Twisted Pair Gigabit Ethernet Segment............. 2-7
LANVIEW LEDs on the VHSIM-G02........................................ 3-1
VHSIM-G02 User’s Guide
xiii
Table
Page
3-1
A-1
A-2
A-3
A-4
VHSIM-G02 LED Functionality .................................................3-2
Physical Properties of the VHSIM-G02.................................... A-1
Environmental Requirements of the VHSIM-G02.................... A-1
Regulatory Compliance of the VHSIM-G02............................. A-1
RJ45 Port Pin Assignments..................................................... A-2
xiv
VHSIM-G02 User’s Guide
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems VHSIM-G02 User’s Guide. This
manual describes the VHSIM-G02 and provides information concerning
features, installation, troubleshooting, information on Local Management,
and specifications for the VHSIM-G02 (Very High Speed Interface
Module).
A general working knowledge of IEEE 802.3z (Gigabit Ethernet),
IEEE 802.3ab (Gigabit Copper) and IEEE 802.3x (Flow Control and
Auto-Negotiation) data communications networks and their physical
layer components is helpful when installing the VHSIM-G02.
The VHSIM-G02 can be installed into compatible Cabletron Systems
2000 and 6000 series products.
The VHSIM-G02 (Figure 1-1) has two ports that provide Gigabit
Ethernet connections. There are two possible modes of operation for the
VHSIM-G02. In mode one, both ports are active and transmit/receive data
simultaneously. This mode can only be selected if the host platform has
16 or less fixed front panel ports. In mode two, one port is active and the
other is redundant. Redundancy is triggered based on link activity; if port
one loses link then port two becomes active. Port one is active by default.
The default mode for the VHSIM-G02 is redundancy.
VHSIM-G02
1
2
Gigabit Ethernet Ports
25491_01
Figure 1-1 VHSIM-G02
The term “host platform” may be used to refer to the module or
standalone device in which the VHSIM-G02 is installed.
NOTE
VHSIM-G02 User’s Guide
1-1
Chapter 1: Introduction
1.1
STRUCTURE OF THIS GUIDE
Read through this manual completely to familiarize yourself with its
the VHSIM-G02. The following list provides an overview of each section
of this manual:
Chapter 1, Introduction, outlines the contents of this manual, describes
the VHSIM-G02 features and concludes with a web site address where
Chapter 2, Installation, describes how to install a VHSIM-G02 into an
Chapter 3, LANVIEW LEDs, describes how to use the VHSIM-G02
LEDs to monitor performance and status.
Chapter 4, Local Management, gives information on Local Management
for the VHSIM-G02.
Appendix A, VHSIM-G02 Specifications, lists the operating
specifications and regulatory compliance for the VHSIM-G02.
1.2
OVERVIEW
The VHSIM-G02 has two RJ45 ports for twisted pair connections to
Gigabit Ethernet networks. The VHSIM-G02 extends the functionality of
various Cabletron Systems interface modules or standalone devices by
providing high-speed uplink capability through copper Gigabit Ethernet
technology (IEEE 802.3ab).
VHSIM-G02 features include the following:
•
•
•
RMON support (Statistics, History, Alarms, Events)
Management
Flow control and Auto-Negotiation (IEEE 802.3x)
1.2.1
LANVIEW Diagnostic LEDs
Cabletron Systems provides a visual diagnostic and monitoring system
called LANVIEW. The VHSIM-G02 LANVIEW LEDs help you quickly
identify transmit, receive, and link status. Chapter 3 provides information
on the VHSIM-G02 LEDs.
1-2
VHSIM-G02 User’s Guide
Document Conventions
1.2.2
Connectivity
The VHSIM-G02 supports two modes of operation for the Gigabit
interfaces. In one mode, the VHSIM-G02 supports one active and one
redundant Gigabit Ethernet twisted pair port. In the other mode, both of
the interfaces can be active at the same time, if the host platform has 16 or
less fixed front panel ports.
The VHSIM-G02 supports Gigabit Ethernet connections on the RJ45
ports using twisted pair. The VHSIM-G02 module supports the
IEEE 802.3ab Gigabit specification and the IEEE 802.3x specification for
flow control and auto-negotiation. The VHSIM-G02 operates in full
duplex mode.
1.3
DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
NOTE
Caution symbol. Contains information essential to avoid
damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action
that could result in personal injury or death due to an electrical
hazard.
1.4
RELATED DOCUMENTATION
The documentation for the host platform in which the VHSIM-G02 is to
be installed, whether standalone device or module, provides additional
information about the setup of the VHSIM-G02. This user’s guide
references procedures in these documents, where appropriate, but does
not repeat them.
Documents can be obtained on the World Wide Web in Adobe Acrobat
Portable Document Format (PDF) at the following site:
VHSIM-G02 User’s Guide
1-3
Chapter 1: Introduction
1.5
GETTING HELP
For additional support related to this device or document, contact
Cabletron Systems using one the following methods.
World Wide Web
Phone
(603) 332-9400
Internet mail
FTP
anonymous
Login
Password
your email address
To send comments or suggestions concerning this document, contact the
Cabletron Systems Technical Writing Department via the following
Make sure to include the document Part Number in the email message.
Before calling Cabletron Systems, have the following information
ready:
•
•
•
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
•
The serial and revision numbers of all involved Cabletron Systems
products in the network
•
•
•
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
•
Any previous Return Material Authorization (RMA) numbers
1-4
VHSIM-G02 User’s Guide
CHAPTER 2
INSTALLATION
Only qualified personnel should install or service this unit.
To install the VHSIM-G02 you need the following items:
•
•
•
Phillips screwdriver
Antistatic wrist strap (shipped with the VHSIM-G02)
Standoff screws (shipped with the VHSIM-G02)
Before using the VHSIM-G02 you should be familiar with the
NOTE
IEEE 802.3z, IEEE 802.3ab, and IEEE 802.3x specification.
The network installation must meet the guidelines contained in
the specification to ensure satisfactory performance.
2.1
UNPACKING THE VHSIM-G02
The VHSIM-G02 and the host platform are sensitive to static
discharges. Use an antistatic wrist strap and observe all static
precautions during this procedure. Failure to do so could result
in damage to the VHSIM-G02 or host platform.
!
CAUTION
Do not use sharp metal objects to open the VHSIM-G02’s
antistatic bag. They can damage the VHSIM-G02.
Unpack the VHSIM-G02 as follows:
the antistatic bag until you are ready to install it.
2. Attach the antistatic wrist strap. Refer to the instructions on the
antistatic wrist strap package.
3. After removing the VHSIM-G02 from the antistatic bag, visually
inspect the device. If there is any sign of damage, contact Cabletron
Systems immediately. Refer to Section 1.5 for instructions. Save the
antistatic bag in the event the VHSIM-G02 must be reshipped.
VHSIM-G02 User’s Guide
2-1
Chapter 2: Installation
2.2
INSTALLING THE VHSIM-G02
You can install a VHSIM-G02 in any Cabletron Systems device that
supports VHSIM technology (e.g., 2E253-49R, 6H252-17).
Refer to the release notes for the version of firmware running
on the Cabletron Systems device to ensure that the
NOTE
VHSIM-G02 is supported.
The following sections provide instructions for installing a VHSIM-G02
in an interface module or in a standalone device. Refer to your specific
interface module or standalone device documentation for exact VHSIM
slot and connector locations.
2.2.1
Installing the VHSIM-G02 in an Interface Module
To install a VHSIM-G02 in an interface module that supports VHSIM
technology, perform the following steps:
1. Note the ports of the interface module that have cables attached to
them. Write down the ports and label the cables to make it easier to
reattach the network properly after the installation. Then disconnect
the cables from the ports.
2. Attach the antistatic wrist strap (refer to the instructions outlined in the
interface module User’s Guide).
The VHSIM-G02 and the host module are sensitive to static
discharges. Use an antistatic wrist strap and observe all static
precautions during this procedure. Failure to do so could result
in damage to the VHSIM-G02 or host module.
!
CAUTION
3. If the module is installed in a chassis, unlock the top and bottom plastic
locking tabs of the module faceplate, and remove the module from the
chassis.
2-2
VHSIM-G02 User’s Guide
Installing the VHSIM-G02
4. Lay the module down with the internal components facing up.
5. Refer to Figure 2-1 and remove the two faceplate mounting screws
and the VHSIM coverplate. Save the screws.
VHSIM Coverplate
Faceplate Mounting Screws
Host Platform
2549_03
Figure 2-1 Removing the VHSIM Coverplate from the Host Platform
VHSIM-G02 User’s Guide
2-3
Chapter 2: Installation
6. Refer to Figure 2-2 and position the VHSIM-G02 behind the module
faceplate, above the connectors.
Standoff Screws
Connectors
(top view)
Connectors
Cutaway view of connectors
VHSIM-G02
1
2
VHSIM-G02
Standoff
SP
Connectors
Standoff
Faceplate Mounting Screws
Host Platform
25491_36
Figure 2-2 Installing the VHSIM-G02 in the Host Platform
7. Align the VHSIM-G02 connectors with the VHSIM connectors on the
module.
When installing the VHSIM-G02, ensure that the pins on the
module align with the connector to prevent bending the pins.
Damage to both the VHSIM-G02 and the module can result if
they are not properly aligned.
!
CAUTION
2-4
VHSIM-G02 User’s Guide
Installing the VHSIM-G02
8. Press down firmly on the VHSIM-G02 until the connectors slide all
the way onto the pins. Ensure that the standoffs on the interface
module align with the standoff screw holes on the VHSIM-G02.
9. Secure the VHSIM-G02 to the module faceplate using the mounting
screws saved in step 5.
10. Secure the VHSIM-G02 to the module standoffs using the standoff
screws shipped with the VHSIM-G02.
11. Reinstall the interface module in the chassis.
12. Reattach the network cabling to the interface module.
2.2.2
Installing the VHSIM-G02 in a Standalone Device
To install a VHSIM-G02 into a standalone device (e.g., 2H252-25R) that
supports VHSIM technology, perform the following steps:
1. Power down the device and remove the power cord.
2. Note the ports that have cables attached to them. Write down the ports
and label the cables to make it easier to reattach the network properly
after the installation. Then disconnect the cables from the ports.
To install the VHSIM-G02 in a standalone device, the device
must first be powered down. Ensure that you remove the power
cord and ONLY the screws required to remove the chassis
cover.
3. Attach the antistatic wrist strap (refer to the instructions outlined on
the antistatic wrist strap package).
The VHSIM-G02 and the device are sensitive to static
discharges. Use an antistatic wrist strap and observe all static
precautions during this procedure. Failure to do so could result
in damage to the VHSIM-G02 or device.
!
CAUTION
4. Remove the standalone device chassis cover. Refer to your specific
standalone device documentation for instructions on removing the
chassis cover.
VHSIM-G02 User’s Guide
2-5
Chapter 2: Installation
5. Refer back to Figure 2-1 and remove the two faceplate mounting
screws and the VHSIM coverplate. Save the screws.
6. Refer back to Figure 2-2 and place the VHSIM-G02 module behind
the standalone device faceplate.
7. Align the VHSIM-G02 connectors with the pins on the standalone
device.
When inserting the VHSIM-G02 onto the device pins, ensure
that the pins do not bend, as this can damage both the device
and the VHSIM-G02.
!
CAUTION
8. Press down firmly on the VHSIM-G02 until the connectors slide all
the way onto the pins. Ensure that the standoffs on the standalone
device align with the standoff screw holes on the VHSIM-G02.
9. Secure the VHSIM-G02 to the device faceplate using the mounting
screws saved in step 5.
10. Secure the VHSIM-G02 to the device standoffs using the standoff
screws shipped with the VHSIM-G02.
Ensure that the chassis cover is in place before reconnecting
the power cord.
11. Reattach the chassis cover to the standalone device, reconnect the
power cord, and reconnect the standalone device to the network.
2-6
VHSIM-G02 User’s Guide
Network Connections
2.3
NETWORK CONNECTIONS
The VHSIM-G02 has two RJ45 connectors for the Gigabit Ethernet
connections, Port 1 and Port 2. The cable used for connections is 4-pair
Category 5 Unshielded Twisted Pair, conforming to the IEEE 802.3ab
specification. The maximum distance supported is 100 meters. Refer to
Appendix A for the pin assignments for the RJ45 port.
The VHSIM-G02’s Gigabit Ethernet front panel ports support
Category 5 Unshielded Twisted Pair (UTP) cabling with an
NOTE
impedance between 85 and 111 ohms.
Connect a twisted pair segment to the Gigabit Ethernet port on the
VHSIM-G02 as follows:
1. Ensure that the device connected to the other end of the segment is
powered ON.
2. Connect the twisted pair segment to the VHSIM-G02 by inserting the
RJ45 connector on the twisted pair segment directly into the RJ45 port
as shown in Figure 2-3.
.
VHSIM-G02
1
2
4001_01
Figure 2-3 Connecting a Twisted Pair Gigabit Ethernet Segment
VHSIM-G02 User’s Guide
2-7
Chapter 2: Installation
3. Verify that a link exists by checking that the port RCV (Receive) LED
is ON (flashing amber, blinking green, or solid green). If the RCV
LED is OFF and the XMT (Transmit) LED is not blinking amber,
perform the following steps:
impedance between 85 and 111 ohms. To operate at 1 Gbps,
category 5 cabling must be used.
b. Verify that the device at the other end of the twisted pair segment
is on and properly connected to the segment.
the proper pinouts (see Appendix A) and check the cable for
continuity.
4. Repeat steps 1 through 3 above, for a second connection, as needed.
5. If a link cannot be established, refer to Chapter 3 for LED
troubleshooting details. Contact Cabletron Systems if a problem
persists. Refer to Getting Help in the Introduction.
Refer to Chapter 4 for information on Local Management for the
VHSIM-G02.
2-8
VHSIM-G02 User’s Guide
CHAPTER 3
LANVIEW LEDs
This chapter describes how to use the LANVIEW LEDs to monitor the
VHSIM-G02 status and diagnose VHSIM-G02 problems. Figure 3-1
shows the location of the VHSIM-G02 LEDs. Refer to Table 3-1 for a
description of the LEDs. Section 3.2 describes redundancy.
3.1
LED DESCRIPTIONS
VHSIM-G02
1
2
Receive (RX)
25491_02
Transmit (TX)
Receive (RX)
Transmit (TX)
Figure 3-1 LANVIEW LEDs on the VHSIM-G02
The terms flashing, blinking, and solid used in Table 3-1
indicate the following:
NOTE
Flashing indicates an irregular LED pulse.
Blinking indicates a steady LED pulse (approximately 50% on
and 50% off).
Solid indicates a steady LED light. No pulsing.
VHSIM-G02 User’s Guide
3-1
Chapter 3: LANVIEW LEDs
Table 3-1 VHSIM-G02 LED Functionality
LED
Color
Definition
Green (Flashing)
Amber (Blinking)
Off
Activity, port enabled.
Port in standby.
Transmit
No activity, port enabled or disabled.
Transmit fault or error.
Diagnostic failure.
Red (Flashing)
Red
Green (Solid)
Green (Blinking)
Amber (Flashing)
Link, no activity. Port enabled.
Link, port disabled.
Link, activity. Port enabled.
Receive
No link, no activity. Port enabled or
disabled.
Off
Red
Diagnostic failure.
3.2
REDUNDANCY
The VHSIM-G02 supports two modes of operation. In the active mode,
both interfaces are enabled, and all LED descriptions will apply to both
ports. In the redundancy mode, one port is active while the other is
redundant.
In the redundancy mode, only one of the two ports on the VHSIM-G02 is
active at one time. The port with link status showing (either a green LED,
solid or blinking, or an amber LED) is the active port. If both ports show a
link, Port 1 is the active port. The default port for the primary port link is
Port 1.
The interfaces can be set in the active mode only if the host platform has
16 or less fixed front panel ports. If the host platform has more than 16
fixed front panel ports, the ports on the VHSIM-G02 will be in
redundancy mode. The host platform will allow the redundancy mode to
be set regardless of the number of fixed front panel ports.
3-2
VHSIM-G02 User’s Guide
CHAPTER 4
LOCAL MANAGEMENT
This chapter provides information about using Local Management with
the VHSIM-G02. The VHSIM-G02 is managed using the Local
Management Ethernet screens for configuration and statistics on the host
platform.
The host platform is the interface module or standalone device
in which the VHSIM-G02 is installed.
NOTE
4.1
REQUIREMENTS
Make sure that the following requirements have been met before
accessing the VHSIM-G02 through Local Management:
•
•
•
The VHSIM-G02 is installed in the host platform.
The device is powered up and running with no error LED conditions.
A Local Management terminal is properly configured and connected
to the host platform. Refer to the host platform user’s guide to establish
a Local Management connection.
4.2
GIGABIT PORT MODE
Local Management Network Tools can be used to change the status of the
Gigabit Port Mode. Either both ports can be enabled at the same time, or
Port 1 can be active and Port 2 can be set up as redundant. Use the
gigabit_port_mode command for this process. Refer to the host
platforms’ Local Management documentation for details on this process.
Refer to Section 3.2 for hardware restrictions on setting redundancy.
Important
The Local Management screens are used by the host platform for both
configuration and statistics information. These screens will not be
repeated in this manual. Refer to the host platform documentation for
information on Local Management screens. Refer to Section 1.4 for
information on how to obtain host platform manuals.
VHSIM-G02 User’s Guide
4-1
Chapter 4: Local Management
4-2
VHSIM-G02 User’s Guide
APPENDIX A
VHSIM-G02 SPECIFICATIONS
This chapter lists the specifications and regulatory requirements for the
VHSIM-G02. Cabletron Systems reserves the right to change these
specifications at any time without notice.
A.1 PHYSICAL AND ENVIRONMENTAL
SPECIFICATIONS
Table A-1 Physical Properties of the VHSIM-G02
3.18 H x 16.51 W x 29.21 D (cm)
1.25 H x 6.5 W x 11.5 D (in)
Dimensions
Weight
0.34 kg (0.75 lb)
911,920 hours
MTBF (Predicted)
Table A-2 Environmental Requirements of the VHSIM-G02
Operating Temperature
5°C to 40°C (41°F to 104°F)
-30°C to 73°C (-22°F to 164°F)
5% to 90% (non-condensing)
Storage Temperature
Operating Humidity
A.2 REGULATORY COMPLIANCE
This equipment meets the following safety and electromagnetic
compatibility (EMC) requirements:
Table A-3 Regulatory Compliance of the VHSIM-G02
UL 1950, CSA C22.2 No. 950,
EN 60950, IEC 950, and 72/73/EEC
Safety
FCC Part 15, ICES-003/NMB-003,
Electromagnetic Compatibility (EMC)
EN 55022, VCCI V-3, EN 50082-1,
89/336/EEC, and AS/NZS 3548
VHSIM-G02 User’s Guide
A-1
Appendix A: VHSIM-G02 Specifications
A.3 GIGABIT PORT PIN ASSIGNMENTS
The following pin assignments are for the RJ45 Gigabit Ethernet ports on
the VHSIM-G02. The twisted pair ports conform to the IEEE 802.3ab
specification. The cables are 4-pair Category 5 UTP, up to 100 meters in
length.
Table A-4 RJ45 Port Pin Assignments
Pin
Function
1
2
3
4
5
6
7
8
TRDA+
TRDA-
TRDB+
TRDC+
TRDC-
TRDB-
TRDD+
TRDD-
A-2
VHSIM-G02 User’s Guide
|