Cambridge Audio Speaker SS10 User Manual

SS10  
6.5” Passive Ceiling Speakers  
Installation Guide  
 
SS10Passiveceilingspeakers
INTRODUCTION  
Thank you for purchasing these Cambridge Audio incognito SS10  
Passive Ceiling Speakers. Incognito is a cost-effective, modular based  
system using standard Cat-5 or Cat-6 cable to distribute hi-fi quality  
sound and video images around the home. The SS10 are for use  
primarily in conjunction with the KP10 amplified keypad.  
About this unit  
Your new Incognito in-ceiling speakers have been designed specifically to  
enhance the performance of your home entertainment system.  
They are the result of an extensive research and development programme  
undertaken to provide you with accurate, uncompromised reproduction  
of movie soundtracks and music. With attention to detail second to  
none, these speakers are designed to deliver maximum enjoyment.  
They mount flush with the ceiling, and you can paint their frames and  
grilles to match the room's decor.  
Please take time to read this guide, as it contains important installation  
information. The SS10 can only be as good as the system it is  
connected to. Please do not compromise on your audio/visual source  
components. Naturally, we recommend products from the Cambridge  
Audio Azur range.  
Now we invite you to sit back, relax and enjoy!  
Matthew Bramble  
Technical Director  
Incognito passive ceiling speakers 3  
 
PREPARING THE LOCATION  
It is advisable to plan all aspects of installation in advance of work  
beginning, preferably with the house/flat building schematics if available.  
Great care should be taken to ensure that all building regulations are  
followed. If in doubt consult an expert.  
2. Use the template to mark the position for the mounting hole at the  
selected location.  
Before cutting ceiling speaker holes, it is suggested that the area is  
tested for clearance by making an L-shaped probe from strong wire  
(see illustration below), drilling a small hole in the target area,  
inserting the probe and slowly turning. Any obstructions will be  
immediately obvious, and the target area can be moved to a more  
suitable position.  
When placing the SS10 speakers, thought should be given to positions  
which give the best desired sound coverage throughout a room, while  
not interfering with existing or planned light fittings or joists. Also, locate  
speakers taking into account location of furnishings for optimal stereo  
reproduction.  
Use an L-shaped probe  
110mm  
Follow these steps to prepare the mounting location:  
to check available void  
space before cutting  
loudspeaker holes  
1. Remove the round cardboard pad from inside the supplied template  
(see below).  
3. Cut the mounting hole with a drywall or keyhole saw.  
Be sure the mounting surface is between 10 and 30mm thick, and  
that there is at least 80mm of clearance behind the mounting  
surface. Also, be sure no wall studs or other objects block the back  
of the speaker.  
SS10  
207mm diameter  
mounting hole  
4 Incognito passive ceiling speakers  
 
SS10 Passive ceiling speakers  
PAINTING THE FRAME AND GRILLE  
CARE AND MAINTENANCE  
Remove grille by inserting a small hook or similar small implement into  
one of the grille openings, then pulling on the grille.  
Your speakers are an example of superior design and craftsmanship.  
These suggestions will help you care for them so you can enjoy them  
for years.  
Fit the clear plastic painting mask provided when painting the speaker  
surround to avoid getting paint getting on the speaker cone.  
Keep the speakers dry. If they get wet dry immediately. Liquids can  
contain minerals that can corrode electronic components.  
Keep the speakers away from dust or dirt, which can cause premature  
wear of parts.  
Wipe the speaker frame occasionally with a damp cloth to keep it  
looking new. Do not use harsh chemicals, cleaning solvents or strong  
detergents.  
Incognito passive ceiling speakers 5  
 
MOUNTING THE SS10  
Before mounting, ensure that the four fixing screws are slackened off so  
that the red mounting dog-legs can move freely.  
2. Separate about 100mm of speaker cable at each end.  
3. Using a wire stripper, remove about 10mm of insulation from  
both ends of each conductor, and then twist the strands of each  
conductor (fig.1).  
Move each red dog-leg foot to the LEFT into it’s holding slot, and then  
insert the speaker into the mounting hole.  
Using a cross-head screwdriver, slowly turn each fixing screw clockwise.  
This will move the mounting dog-legs out of their slots.  
4. Observing polarity is of the utmost importance while connecting  
your speakers. Ensure that the red (+) terminals on your  
amplification system are connected to the red (+) on the  
speakers, and black (-) on your amplification system to black (-)  
on your speakers (fig.2).  
Tighten each fixing screw until the mounting dog-legs grip the ceiling.  
CONNECTING THE SS10  
The speaker cable is coded with a bead or stripe down one  
lead’s insulation, or has differently coloured wires.  
Press the spring-loaded red or black tab back to reveal the  
connecting hole. Insert the stripped end of the speaker wire,  
then release the tab.  
Do not compromise the performance of your system by using  
inferior quality speaker cables. We recommend that high quality  
cables of 16 gauge or higher be used. Your professional dealer will  
give you good advice. Always unplug all A.C. powered components  
before making any loudspeaker or component connections. This will  
avoid the risk of electric shock or damage to your equipment.  
5. If your speakers are wired incorrectly they will be out of phase  
and sound hollow and indistinct, with a weak bass. Re-check  
your connections for correct polarity and reverse the connections  
if necessary.  
Follow these steps to connect the speaker to your amplification system:  
1. Route the speaker cable from your amplification system to the  
speakers.  
Avoid routing the speaker cable near electrical wires  
100mm  
10mm  
Do not nail or staple the cable  
fig.1.  
fig.2.  
6 Incognito passive ceiling speakers  
 
SS10 Passive ceiling speakers  
TROUBLESHOOTING  
SPECIFICATIONS  
+
Frequency response  
Impedance  
60Hz–20kHz ( / 2dB)  
-
There is no sound  
4 Ohms  
Ensure that the amplifier is set correctly.  
Operational efficiency  
Weight  
90dB for 2.83V  
1.1kg / 2.4lbs  
240 x 75mm (9.4 x 3”)  
Check that the interconnects are inserted correctly.  
The sound is distorted or garbled  
Dimensions  
Check aerial connections and placements.  
The crossed-out wheeled bin is the European Union  
symbol for indicating separate collection for electrical  
and electronic equipment. This product contains  
electrical and electronic equipment which should be  
reused, recycled or recovered and should not be  
disposed of with unsorted regular waste. Please return  
the unit or contact the authorised dealer from whom you  
purchased this product for more information.  
There is a hum coming from the speaker  
Ensure that all cable connections are secure.  
There is unwanted background noise and interference  
Move the tuner (or other source) away from any other electrical  
equipment that may be likely to cause interference.  
The remote handset will not function  
Check that the batteries have not expired.  
Ensure that nothing is blocking the remote sensor.  
Incognito passive ceiling speakers 7  
 
LIMITED WARRANTY  
Cambridge Audio warrants this product to be free from defects in  
materials and workmanship (subject to the terms set forth below).  
Cambridge Audio will repair or replace (at Cambridge Audio’s option)  
this product or any defective parts in this product. Warranty periods may  
vary from country to country. If in doubt consult your dealer and ensure  
that you retain proof of purchase.  
Audio dealer, or authorised service agent which is authorised to do  
Cambridge Audio warranty work. Any unauthorised repairs will void this  
warranty. This warranty does not cover products sold AS IS or WITH  
ALL FAULTS.  
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY  
ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO  
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN  
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS  
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND  
IMPLIED WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED  
TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A  
PRACTICAL PURPOSE.  
To obtain warranty service, please contact the Cambridge Audio  
authorised dealer from which you purchased this product. If your dealer  
is not equipped to perform the repair of your Cambridge Audio product,  
it can be returned by your dealer to Cambridge Audio or an authorised  
Cambridge Audio service agent. You will need to ship this product in  
either its original packaging or packaging affording an equal degree  
of protection.  
Proof of purchase in the form of a bill of sale or receipted invoice, which  
is evidence that this product is within the warranty period, must be  
presented to obtain warranty service.  
Some countries and US states do not allow the exclusion or limitation of  
incidental or consequential damages or implied warranties so the above  
exclusions may not apply to you. This warranty gives you specific legal  
rights, and you may have other statutory rights, which vary from state to  
state or country to country.  
This warranty is invalid if (a) the factory-applied serial number has been  
altered or removed from this product or (b) this product was not  
purchased from a Cambridge Audio authorised dealer. You may call  
Cambridge Audio or your local country Cambridge Audio distributor to  
confirm that you have an unaltered serial number and/or you purchased  
from a Cambridge Audio authorised dealer.  
This warranty does not cover cosmetic damage or damage due to acts  
of God, accident, misuse, abuse, negligence, commercial use, or  
modification of, or to any part of, the product. This warranty does not  
cover damage due to improper operation, maintenance or installation,  
or attempted repair by anyone other than Cambridge Audio or a Cambridge  
8 Incognito passive deckenlautsprecher  
 
incognito SS10  
Part No. AP17791/1  
 

Bogen Microphone GDU150 User Manual
Bosch Appliances Home Security System LBB3580 User Manual
Bowers Wilkins Speaker CASA ACM 60 User Manual
Broan TV Mount 52WH244DP User Manual
Brother Car Stereo System HL 4040CN User Manual
Brother Sewing Machine 885 X06 X08 X16 X18 X26 X28 User Manual
Bushnell Binoculars 110833 User Manual
Cabletron Systems Switch SEH 24 User Manual
Can Am Offroad Vehicle DS250 User Manual
Chauvet Surge Protector DMX 4 LED User Manual