Candy Washer GC1472D1 User Manual

Washing machine

Instructions for use

M) N.B!

If the appliance is installed on a carpeted floor ensure that the ventilation holes on the

base of the appliance are not obstructed.

N) If the appliance is not running properly or breaks down, switch it off, turn off the tap and do

not tamper with the appliance.

Consult only the Authorised Technical Support Service for possible repair and ask them to

use original spare parts.

Failure to comply with the above can compromise the safety of the appliance.

O) If the appliance’s power cable should ever need replacing, consult the Authorised

Technical Support Service

General delivery notes

Please check that the following items are delivered with the appliance:

- Instruction manual

- Certificate of guarantee

- Inlet hose

Check that no damage has occurred during transit, and if so, call your nearest Authorised

Technical Support Service agent.

Quick start

Washing

Open the door by using the handle “A” (Fig. 1, page 6)

Select laundry and put it in the machine

Close the door

Put detergent in the compartments as indicated in the programme guide in this instruction

manual

Select programme

Wait for the “STOP” indicator light to flash

Safety notes.

Note:

for cleaning or maintenance of the washing machine.

A) Pull out the plug

B) Turn off the tap

Press additional function buttons (if required)

C) Candy equips all its appliances with earthing. Ensure that the mains supply is earthed,

and if it is not, seek assistance from a qualified person.

D) Do not touch the appliance when hands or feet are wet or damp. Do not use the appliance

with bare feet.

Press the “Start/Pause” button (page 7)

After few seconds the appliance starts working.

E) The use of adapters, multiple connectors and/or extensions is not recommended.

After washing

The indicator light “STOP” will go on.

Wait for the door lock to be released

(about 2 minutes after the programme has finished).

The “Door Security” indicator light will go out.

Switch off the washing machine by turning the

selector to “OFF” position.

Note:

water temperature can reach 90°C during the wash cycle.

F) Check there is no water left in the drum before opening the door.

G) Do not allow children or unauthorised persons to use the appliance without supervision.

H) Do not pull the power cable or the appliance itself to remove the plug from the socket.

I) The appliance must not be exposed to weather conditions (rain, direct sun, etc...)

L) When moving the appliance never lift it by the controls or by the detergent drawer.

When in transit never rest the door against the trolley or transport the appliance without

the polystyrene base.

Open the door and remove the laundry.

Ensure that the machine is correctly installed in line with the instructions found on page 27.

Door handle

Press the finger-bar inside the door handle to open the door.

Description of controls

Fig. 1

DOOR SECURITY indicator light

The “Door Security” indicator light is illuminated when the door is fully closed and the machine is ON.

When "Start/Pause" is pressed on the machine with the door closed the indicator will flash

momentarily and then illuminate.

If the door is not closed the indicator will continue to flash.

Aspecial safety device prevents the door from being opened immediately after the end of the cycle.

Wait for 2 minutes after the wash cycle has finished and the “Door Security” light has gone out

before opening the door. At the end of the cycle turn the programme selector to "OFF" .

START/PAUSE button

When a programme is selecting, wait for the “STOP” indicator

light to flash before pressing the "Start/Pause" button.

Press to start the selected cycle (according to the selected cycle one indicator lights will go on) .

NOTE: When the "Start/Pause" button has been pressed,

the appliance can take few seconds before it starts

working.

Door handle

"Door Security" indicator light

"Start/Pause" button

"Fast wash" button

Changing the settings after the programmes has started (PAUSE)

The programme may be paused at any time during the wash cycle by holding down the

"Start/Pause" button for about two seconds. When the machine is in the paused mode, the

indicator light "Time To End", spin speed and option buttons will flash.

To restart the programme, press the "Start/Pause" button once again.

If you wish to add or remove items during washing, wait 2 minutes until the safety device

unlocks the door.

"Allergy care" button

"Stain vanish" button

"Delay Start" button

"Spin Speed" button

When you have carried out the manoeuvre, close the door, press "Start/Pause" button and

the appliance will continue working where it left off.

Spin speed indicator light

"Time To End" indicator light

Buttons indicator light

CANCELLING THE PROGRAMME

To cancel the programme the programme selector should be rotated to the "OFF" position.

Programme selector with "OFF" position

Detergent drawer

The option buttons should be selected before pressing

the "Start/Pause" button.

DELAY START button

Appliance start time can be set with this button, delaying the start by 3, 6 or 9 hours.

FAST WASH button

Press the button to select or deselect this function.

Pressing this button reduces the time of the wash programme by a maximum of 50 minutes

depending on the programme and the temperature selected. The "Super Rapid" button can

be used for washing loads of 1 to 8 kg. This option may only be utilised on COTTONS and

SYNTHETICS programmes.

Proceed as follows to set a delayed start:

Select a programme (“STOP” indicator light blinks)

Press "Delay Start" button (each time the button is pressed the start will be delayed by 3, 6

or 9 hours respectively and the corresponding light will blink).

Press "Start/Pause" to commence the Delay Start operation (the indicator light associated

with the selected Delay Start time stops blinking and remains ON).

ALLERGY CARE button

By pressing this button you can activate a special new wash cycle in the Cotton and Mixed

Fabrics programs, thanks to the new Sensor Activa System. This option treats with care the fibres

of garments and the delicate skin of those who wear them.

At the end of the required time delay the programme will start.

To cancel the Delay Start function :

The load is washed in a much larger quantity of water and this, together with the new combined

action of the drum rotation cycles, where water is filled and emptied, will give you garments which

have been cleaned and rinsed to perfection. The amount of water in the wash is increased so that

the detergent dissolves perfectly, ensuring an efficient cleaning action. The amount of water is also

increased during the rinse procedure so as to remove all traces of detergent from the fibres. This

function has been specifically designed for people with delicate and sensitive skin, for whom even

a very small amount of detergent can cause irritation or allergy.

You are advised to also use this function for children’s clothing and for delicate fabrics in general,

or when washing garments made of towelling, where the fibres tend to absorb a greater quantity of

detergent. To ensure the best performance for your wash, this function is always activated on the

Delicates and Woollens programs.

press the "Delay Start" button until the indicator lights will be off (The "STOP" light blinks)

and the programme can be started manually using the "Start/Pause" button or switch off the

appliance by turning the programme selector to "OFF" position.

Warning: If there is any break in the power supply while

the machine is operating, a special memory stores the

selected programme and, when the power is restored, it

continues where it left off.

SPIN SPEED button

The spin cycle is very important to remove as much water as possible from the laundry without

damaging the fabrics. You can adjust the spin speed of the machine to suit your needs.

By pressing this button, it is possible to reduce the maximum speed, and if you wish, the spin cycle

can be cancelled.

STAIN VANISH Button

By pressing this button, which can only be activated in the Cotton cycles, the sensors in the

new Activa system come into operation. They affect both the selected temperature, keeping

it at a constant level throughout the wash cycle, and the mechanical function of the drum.

The drum is made to turn at two different speeds at crucial moments. When the detergent

enters the garments, the drum rotates in such a way that the detergent is distributed in a

uniform manner; during the wash and rinse procedures, however, the speed increases in

order to maximise the cleaning action. Thanks to this special system, the efficiency of the

wash procedure is improved WITHOUT ANY INCREASE IN THE LENGTH OF THE

PROGRAM.

To reactivate the spin cycle press the button until you reach the spin speed you would like to set.

To prevent damage to the fabrics, it is not possible to increase the speed over that which is

automatically suitable during the selection of the program.

It is possible to modify the spin speed without to pausing the machine.

Note:

The machine is fitted with a special electronic device, which

prevents the spin cycle should the load be unbalanced.

This reduces the noise and vibration in the machine and so

prolongs the life of your machine.

PROGRAMME selector with "OFF" position

Spin speed indicator light

When you set a program, the maximum possible spin speed will be automatically shown by

the relevant indicator light.

Rotates in both directions.

Choosing a smaller spin speed by the appropriate button, the relevant indicator light will go on.

The machine is turned on by

selecting a programme via the

programme selector. This status

will be indicated by the "STOP"

indicator light flashing, this light

will continue to flash until the

machine has started or the

machine is returned to the

"OFF" position.

TIME TO END indicator light

In order to manage your time better, this washing machine features an indicator light system

that keeps you constantly informed on the remaining cycle time.

Indicator light 90:

Remaining time above 60 minutes.

Indicator light 60:

Remaining time less than 60 minutes.

Indicator light 30:

Remaining time less than 30 minutes.

Press the "Start/Pause" button to start the selected cycle.

Indicator light 15:

Remaining time less than 15 minutes.

Once a programme is selected the programme selector remains stationary on the selected

programme till cycle ends.

Indicator light STOP:

End of the programme.

Switch off the washing machine by turning the selector to "OFF".

Note:

Buttons indicator light

The indicator light around the option buttons will light when specific options are selected.

The programme selector must be returned to the "OFF" position

at the end of each cycle or when starting a subsequent wash

cycle prior to the next programme being selected and started.

TABLE OF PROGRAMMES

PROGRAM FOR:

PROGRAMME

SELECTOR ON:

TEMP.

°C

WEIGHT

MAX

CHARGE DETERGENT

Resistant fabrics

9 0 W hite

90°

60°

40°

●

Whites

Cotton, linen

6 0 +

prewas h

Cotton, mixed

resistant

Whites with

Prewash

●

Fast coloureds

6 0 Soiled

Cotton, mixed

4 0

Fast coloureds

Coulorfas t

Please read these notes

3 0

Delicates

30°

Non fast coloureds

●

When washing heavily soiled laundry it is recommended the load is reduced to 4 kg

maximum.

Cotton

Non fast coloureds

cold wash

* Programmes according to CENELEC EN 60456.

6 0 +

Mixed fabrics and synthetics

Fast coloureds with

Prewash

60°

50°

40°

●

prewas h

Mixed, resistant

The spin speed may also be reduced, to match any guidelines suggested on the

fabric label, or for very delicate fabrics cancel the spin completely this option is

available with a spin speed button.

Cotton, mixed fabrics,

synthetics

6 0 Soiled

Fast coloureds

Synthetics (nylon,

perlon), mixed cotton

5 0 Synth’s

Fast coloureds

Non fast coloureds

●

4 0

Coulorfas t

3 0

Shirts

Mixed, delicate

synthetics

30°

Non fast coloureds

cold wash

4 0

40°

30°

Delicates

●

Delicates

“MACHINE

WASHABLE”

woollens

Very delicate fabrics

1,5

Wool

3 0

“MACHINE

WASHABLE”

woollens

1,5

Wool

Hand

●

30°

Hand wash

Rinse

3 0

1,5

●

Rins e

Fast spin

Spin

Drain only

Drain

Mix & Wash system

programme

40°

50°

Mix & Was h

Rapid 3 2 ’

●

Rapid 32 minute

“MIX & WASH SYSTEM” PROGRAMME

This is an exclusive Candy system and involves 2 great advantages for the

consumer:

Programme selector

For the various types of fabrics and various degrees of dirt the washing machine has 4

different programme bands according to: wash cycle, temperature and length of cycle (see

table of washing cycle programmes).

• to be able to wash together different type of fabrics (e.g. cotton + synthetic

etc…) NON-FAST COLOUREDS;

• to wash with a considerable energy saving.

The "Mix & Wash" programme has a temperature of 40°C and alternate

dynamic phases (the drum that turns) to static phases (fabrics in soak in

phase of rest) with the programme duration that almost reaching the 3 hours.

The energy consumption for the complete cycle is only 850 W/h.

1 RESISTANTS FABRICS

COTTONS

The programmes have been designed for a maximum wash and the

rinses, with spin intervals, ensure perfect rinsing.

The final spin gives more efficient removal of water.

Important:

2 MIXED AND SYNTHETIC FABRICS

MIXED/

SYNTHETICS

• the first washing of new coloureds fabrics must be done separately;

• in every case, never mix NON-FAST COLOUREDS fabrics.

The main wash and rinse gives the best results thanks to the rotation

rhythms of the drum and to the water levels.

A gentle spin will mean that the fabrics become less creased.

32 MINUTE RAPID PROGRAMME 50°C

The 32 minute rapid programme allows a complete washing cycle to be

carried out in approximately 30 minutes, with up to a maximum load of 2 kg

and a temperature of 50°C.

When selecting the "32 minute rapid" programme, please note that we

recommend you use only 20% of the recommended quantities shown on

the detergent pack.

3 SPECIAL DELICATE FIBRES

DELICATES

This is a new wash cycle which alternates washing and soaking and is

particularly recommended for very delicate fabrics such as Pure Machine

Washable Wool. The wash cycle and rinses are carried out with high water

levels to ensure best results.

WOOLMARK PROGRAMME

The special cycle, certified by WOOLMARK, enables to thoroughly wash

garments without damaging them. The cycle comprises of alternate periods

of activity and pauses.

FUZZY LOGIC

SPECIAL “HAND WASH”

Through every wash phase Fuzzy Logic allows the Activa Smart to monitor information on

the wash load in the drum.

This washing machine also has a gentle Hand Wash programme cycle.

This programme allows a complete washing cycle for garments specified

as “Hand Wash only” on the fabric care label. The programme has a

temperature of 30°C and concludes with 3 rinses and a slow spin.

So, as soon as the Activa Smart is set in motion it:

• adjusts the amount of water required

• determines the length of the wash cycle

• controls rinsing

4. SPECIALS

according to the type of fabric selected to be washed it:

SPECIAL “RINSE” PROGRAMME

• adjusts the rhythm of drum rotation for the type of fabric being washed

• recognises the presence of lather, increasing, if necessary, the amount of water during

rinsing

This programme carries out three rinses with a intermediate spin (which

can be reduced or excluded by using the correct button). It can be used for

rinsing any type of fabric, eg. use after hand-washing.

• adjusts the spin speed according to the load, thus avoiding any imbalance.

In this way the ACTIVA SMART is able to decide, by itself, the most suitable programme for

each individual wash from the hundreds of possible wash combinations.

SPECIAL “FAST SPIN” PROGRAMME

Programme “FAST SPIN” carries out a maximum spin (which can be

reduced by using the correct button).

Fuzzy Logic meets the need for easy use by permitting a simplified programme selection. In

fact, the user need only tell the machine the type of fabric in the drum (cotton, mixtures,

delicate or woollens) and the degree of soiling, to obtain a perfect wash with the highest

level of drying possible with a spin which really cares for your clothes.

DRAIN ONLY

This programme drains out the water.

Detergent drawer

Detergents, washing aids and amounts to use

Choice of detergent

The detergent drawer is split into 3 compartments:

- the compartment labelled "1" is for prewash detergent;

- the compartment labelled " " is for special additives,

General purpose detergents

Powder detergents, for a thorough wash, with bleaching agent, particularly suitable for

use in hot wash programmes (60°C and over), for heavily soiled and stained laundry.

Liquid detergents, particularly suitable for grease stains, such as greasy skin marks,

cosmetics and oil.

fabric softeners, fragrances, starch, brighteners etc;

These detergents are not suitable for washing stained laundry, as they do not contain

bleach.

Biological detergents, not all the products available give a really thorough wash.

- the compartment labelled "2" is for main wash

detergent.

Additional laundry aids

NOTE:

Water softener, means less detergent can be used where water hardness is classed as

hard to very hard.

Some Detergents are Difficult to

utilise. Ensure to use an in drum

dispenser if recommended by

the detergent Manufacturer.

Prewash substances, for the programmed treatment of stains prior to the main wash.

Using them means the subsequent wash can be at a low temperature or with bleach-free

detergents.

Fabric softener, prevents static build-up in synthetic fabrics and softens fabrics.

If you own a tumble dryer, clothes are softened even without the use of a fabric softener.

Do not put solvents in the washing machine!

Note: only put liquid products in the compartment

labelled “ ” . The machine is programmed to

automatically take up additives during the final rinse

stage for all wash cycles.

Keep detergents and other laundry products out of children’s reach.

Before pouring in the detergent check that there are no foreign bodies in the detergent

drawer.

Dosage details are usually shown on the detergent packaging. Follow those instructions.

Dosages

Useful advice for users

Only use detergents which are suitable for use in a washing machine.

You will obtain the best results from your wash with the minimum use of chemical products

and the best care for your laundry if you take into consideration the degree of soiling as well

as the type of detergent to choose.

Tips on using your domestic appliance in the most environmentally-friendly and economical

way

The amount of detergent to use depends on:

- water hardness: depending on the hardness of the water and the type of detergent used, it

is possible to reduce the amount of detergent.

Do a full load in your washing machine

To prevent any possible waste of energy, water or detergent we recommend that you put a

full load in your washing machine, not exceed the recommended maximum load size.

Up to 50% energy saving can be made with one full load compared to two half load washes

the degree of soiling: it is possible to reduce the amount of detergent used depending on

the degree of soiling.

amount of laundry: it is possible to reduce the amount of detergent when washing only a

small amount of laundry.

When is prewashing really needed?

Only with particularly dirty loads!

Energy savings of 5 to 15% are made by not selecting the prewash option for normal soiled

laundry.

Dosage for powder detergent

For normal and low concentration detergents: for normally soiled laundry choose a

programme without prewash.

Which wash temperature should you choose?

Put the detergent in compartment “2” of the drawer.

For heavily soiled laundry, choose a programme with prewash.

Put 1/4 of the detergent in compartment “1”, 3/4 in compartment “2” of the drawer.

When using water softeners, first put in the detergent, then add the softener to compartment “2”.

For highly concentrated detergents not in single dose format, follow what is shown on pack

exactly as regards type and amount of dosage.

Using stain removers before machine washing reduces the need to wash at temperatures

over 60°C.

Energy savings of up to 50% can be made by using a 60°C wash temperature rather than

90°C

To avoid the difficulty of checking if the detergent has been taken up, use the dosage aids

provided in the detergent packaging.

Liquid detergent dosage

Liquid detergents may be used in accordance with the instructions on the relevant

packaging, for all programmes without prewash, by using the special container which is

placed in the drum or, for those models that have it, in the special insert for liquid detergents.

The correct way to wash

Main wash

Sorting the laundry

Preparing the laundry

A) Select the laundry.

It is recommended you wash only items which are machine washable with water and

detergent and not dry-clean items.

Loading the laundry

B) Open the porthole.

If you need to wash rugs, bedspreads or other heavy items, it is best not to spin them.

C) Put the laundry in the washing machine.

Close the porthole again, ensuring that no items of

laundry are obstructing the lock.

Sort the laundry according to fabric type, degree of soiling and wash temperature: Always

follow the wash care advice on the garment label for the most suitable care and

treatment of the laundry

Putting detergent in machine

Laundry for hot wash

D) Open the drawer, choose the detergent and put in

the correct amount, according to the manufacturer’s

instructions and the advice on page 17.

Add any other laundry aids (see page 17). Close the

drawer again.

Coloured, easy-care materials

Delicates and wool

Wash by hand

Items labelled with the following symbol are not suitable for machine washing:

Dry clean

Selecting the wash programme

For very delicate items, such as net curtains, underwear, tights etc., you are advised to

use a laundry net or wash bag.

Woollen items must be labelled with the "Pure New Wool" symbol to be washed in the

Refer to the programme guide or the programme descriptions on the machine to select the

most suitable programme.

Turning the selector knob, the required programme is activated.

Wait for the “STOP” indicator light to flash.

machine

, and must also be labelled "non-matting" or "machine washable".

Colour often leaks from new coloured items.

This can then colour other lighter items being washed.

We therefore recommend that coloured items should be washed for the first time

separately.

Press additional function buttons (if required).

For future washes, colourfast items can only be washed with whites up to 40°C.

Check that the tap is turned on and that the discharge hose is positioned correctly.

Press the "Start/Pause" button.

When the "Start/Pause" button is pressed the machine sets the working sequence in motion.

Note: when sorting laundry

check there are no metal objects in the laundry

(such as paper clips, safety pins, pins, coins

etc...);

The programme carries out with the programme selector stationary on the selected

programme till cycle ends.

Warning: If there is any break in the power supply while the machine is operating, a special

memory stores the selected programme and, when the power is restored, it continues where

it left off.

button up pillowcases, fasten zips, hook & eye

fasteners, belts and long dressing gown cords;

remove curtain hooks;

pay close attention to the labels on items

if you notice stubborn stains whilst sorting the

laundry, remove them using a special detergent or

a special stain remover.

When the programme is finished

At the end of the programme the indicator light “STOP” will go on.

Wait for the door lock to be released (about 2 minutes after the programme has finished).

The "Door Security" indicator light will go out.

Switch off the machine by turning the programme selector on the “OFF” position. Open the

door and remove the laundry. Turn off the tap.

We recommend that you do not do a full load of towelling items only as these become too

heavy since they absorb a lot of water.

Attention: if the filter needs cleaning while there is

washing still in the drum, follow the instructions on the

following page to empty the water. This will prevent

excessive loss of water via the filter.

Cleaning and routine maintenance

Do not use alcohol-based scourers and / or thinners on the outside of your washing machine,

just a wipe with a damp cloth will suffice. The washing machine needs very little maintenance:

- Cleaning the drawer compartments.

- Cleaning the filter.

- Cleaning the door glass.

Cleaning the door glass

Cleaning the drawer compartments

Even if it is not strictly necessary, it is good to clean the

compartments for bleaching detergents and additives

occasionally.

A) To do this you just need to pull them out firmly, but

without forcing them.

Regularly clean the door glass with a damp cloth. A build

up of soiling and

residues from the water may result in water leaking from

the door.

Do not use abrasive cleaners as they can scratch the

surface.

B) Clean everything in the compartment under running

water.

C) Put everything back in its proper place.

Transporting the appliance or long

periods when appliance is not in

use

Cleaning the filter

The washing machine is fitted with a special filter for

handling large deposits which could block the discharge

hose (coins, buttons etc.) and which can, therefore, be

easily retrieved.

If the appliance is being transported or is out of use for

long periods in unheated places, all remaining water

must be completely removed from the hoses.

Ensure mains power is off, then unclip the hose and

point it downwards into a basin until all the water has

emptied out.

We recommend that the filter be cleaned at least

once a month.

The cleaning operation is as follows:

1) Open the flap

When finished, repeat the operation in the reverse order.

2) Only available on certain models:

Pull out the corrugated hose, remove the stopper and

drain the water into a container.

3) Before removing the filter, place an absorbent towel

below the filter cap to collect the small amount of

water likely to be inside the pump

4) Turn the filter anti-clockwise until it stops in the

vertical position.

Remove and clean.

5) After cleaning, replace the filter and lock by tightening

the filter screw. Then follow all procedures described

above in reverse order.

Note:

The use of environmentally-friendly, phosphate-free detergents can have the following effects:

Investigating malfunctions

waste water from rinsing may be cloudier because of the presence of zeolites held in

suspension, without the rinse performance being adversely affected;

presence of white powder (zeolites) on laundry after washing, which is not absorbed by

the fabric and does not alter the colour of the fabric.

The presence of foam in the final rinsing water is not necessarily an indication of poor

rinsing.

Anionic surfactants used in washing detergent formulae often prove to be difficult to

remove from the laundry itself and, even in small quantities, can still cause considerable

foam production.

What might be the cause of…

Defects you can remedy yourself

MALFUNCTION CAUSE

REMEDY

1. Does not work on any

programme

Plug not in socket.

Not switched on.

Power failure.

Fuse blown.

Plug it in.

Switch on.

Check.

Carrying out more rinse cycles does not serve any purpose in such cases.

Door open.

Close door.

2. Does not fill with water

See cause 1.

Check.

Tap turned off.

Turn on tap.

Programme selector not correctly

positioned.

Fill hoses are kinked

Position programme selector

correctly.

Straighten fill hoses

CUSTOMER SERVICE AND GUARANTEE

3. Water does not drain

away

Kink in discharge hose.

Foreign bodies in filter

House drain is blocked

Straighten discharge hose.

Examine filter (see pages 22-23)

Clean drain

Your new appliance is fully guaranteed by the manufacturer for 12 months against

electrical/mechanical breakdown excluding:

A. Any faults which occur due to bad installation or misuse of the machine.

B. Any faults which occur due to repair of, or interference with, the machine by any person

not authorised by the manufacturer to carry out service.

C. Any faults which arise from parts fitted to the machine which are not the manufacturers

original parts.

D. Any faults arising from non-domestic use or unusual or abnormal use of the machine.

E. Any faults arising from operation at an incorrect voltage.

F. Any faults arising from incorrect operation of the machine.

The guarantee applies to Gt. Britain and Northern Ireland only, and is an addition to your

statutory rights.

4. Water on floor around

the washing machine

Leaking gasket between tap and water

inlet hose.

Replace gasket and tighten hose and

tap well.

House drain is blocked

Clean drain

Soap drawer blocked with soap residues

Clean soap drawer

5. Does not spin

Water has not yet drained away.

"No spin" selected (certain models only).

Wait a few minutes for machine to empty.

Reset button or turn "no spin" knob.

6. Machine vibrates a lot

during spin

Washing machine not completely level.

Transit brackets not removed yet.

Load not distributed evenly.

Adjust the special adjustable feet.

Remove transit brackets.

Rearrange the laundry evenly.

7. Door will not open

Two minutes have not elapsed since the

programme finished.

Wait two minutes.

After Sales Service

If, having investigated the possible malfunctions on the chart on the previous page, you

believe the appliance is not working correctly, please call our After Sales Service dept. on

telephone number:

The machine makes a

different noise when

spinning! This is because it

has a brush motor for better

performance.

Only a small level of water can be

seen in the drum! This is because

new machines do not use much

water, yet achieve the same

standard of washing and rinsing.

Gias Service

Tel: 08705 400 600

(Eire 018301 666)

Support Service

SETTING UP + INSTALLATION

Remove the polystyrene base and place the machine near

its permanent position (diagram 1).

Carefully cut through the hose retaining clip at the rear of

the appliance (diagram 2).

Remove the 4 fixing screws marked (A) and remove the 4

spacers marked (B) (diagram 3).

Cover the 4 holes using the caps provided in the instruction

booklet pack (diagram 4).

Fig. 2

Technical data

8 kg

0,05 ÷ 0,8 MPa

●

Max. load of dry laundry

●

Water pressure

WARNING:

Measurements

●

Width

Depth

Height

DO NOT LEAVE THE PACKAGING WITHIN REACH OF CHILDREN AS IT IS A POTENTIAL

SOURCE OF DANGER.

60 cm

54 cm

85 cm

Apply the insulation sheet of corrugated material to the base

as shown.

NB: For specifications regarding electrical data, see the data panel on the front of the washing

machine (porthole area) - as shown in diagram above.

Use the 4 feet to level the machine with the floor:

a) Turn the nut clockwise to release the screw adjuster on the foot.

b) Rotate the foot to raise or lower it until it stands firmly on the

Appliance complies with European Directives 73/23/EEC and 89/336/EEC, replaced

by 2006/95/EC and 2004/108/EC, and subsequent amendments.

ground.

c) Lock the foot in position by turning the nut

anti-clockwise until it comes up against the bottom of the machine.

Note: we recommend you keep the braces and screws

to immobilise the machine for future transit.

Note: it is advisable to turn off the tap after each wash

to isolate the washing machine from the water supply.

The Manufacturers will not be responsible for any

possible damage to the machine caused by not

following the rules relating to releasing the mechanism.

The user is responsible for all costs of installation.

For the washing machine to function properly the terminal end of the discharge hose (mouth)

must be at a minimum of 50 cm and a maximum of 85 cm from the ground.

ELECTRICAL CONNECTIONS

After installation, the appliance must be positioned so that the plug is accessible.

If the plug we supply does not fit

Water connection

The appliance must be connected to the water mains using new

hose-sets.

CUT IT OFF AND DESTROY IT!

You can’t use it on other appliances, and the exposed wires could be dangerous if plugged in.

To fit a replacement plug, proceed as follows:

The old hose-sets should not be re-used.

The machine has an inlet hose with 3/4" B.S.P threaded end

connection to attach between the threaded connector on the

appliance and the cold water supply.

Connect

to the terminal in the plug

green and yellow wire

marked with the letter E,

OR marked

This machine only uses cold water, therefore

only one hose is needed to connect to the cold

water supply. Do not connect to the hot supply.

Cold fill is an energy efficient system. Only the

water required for the washing is heated.There

is no loss of heat in the pipeline from a hot

water tank or boiler to the machine.

with the symbol,

OR coloured green,

OR coloured green and yellow.

blue wire

marked N

OR coloured black.

brown wire

marked L

OR coloured red.

WARNING

This appliance must be earthed

Fuses and plugs

min 4 cm

This appliance should be used only on a socket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equipped with a 13 amp fuse which is BS 1362 ASTA

approved. Any replacement should be exactly the same.

+2,6 mt max

If the fuse cover is lost, do not use the plug until it is replaced. A correct replacement fuse

cover (obtainable from your local retailer) must be the same colour as shown or named on

the insert on the base of the plug.

min 50 cm

max 85 cm

NOTES

......................................................................................................................................................................................................................

The manufacturer declines all responsibility in the event of any printing mistakes in

this booklet. The manufacturer also reserves the right to make appropriate

modifications to its products without changing the essential characteristics.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste handling of this

product.

The symbol on the product indicates that this product may not be treated as household waste. Instead it shall

be handed over to the applicable collection point for the recycling of electrical and electronic equipment

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your

local city office, your household waste disposal service or the shop where you purchased the product.

Belkin Surge Protector BZ108130IR2M User Manual
Belkin Wireless Office Headset USB 20 pocket hub User Manual
Black Box Headphones Voyager 510 User Manual
Blanco Indoor Furnishings 510 871 User Manual
Bodum Coffeemaker 1308 16 User Manual
Briggs Stratton Portable Generator 10000 Watt User Manual
Brother Sewing Machine XC9110 021 User Manual
Canon Camcorder 2807B005 User Manual
Canon Photo Printer BJC 4200 User Manual
Cisco Systems Camcorder Mino2HD User Manual