Cannon Electric Pressure Cooker 10390G Mk2 User Manual

WINCHESTER Mk2  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
Use and Installation Instructions  
The cooker must be installed in accordance with the regulations in force and  
only used in a well ventilated space.  
Read these instructions prior to installing or using the cooker and  
retain them for future reference.  
The Data Badge is located below the oven door.  
Part no. 4466200011-02  
 
CONTENTS  
CONTENTS  
PAGE  
INTRODUCTION  
FOR YOUR SAFETY  
2
3
USER’S INSTRUCTIONS  
Automatic Cooking  
Electronic Clock Operation  
Hotplate  
5
6
7
12  
14  
15  
18  
20  
23  
Grill  
Oven  
Oven Cooking Chart  
Care and Cleaning  
Something Wrong With Your Cooker?  
INSTALLATION INSTRUCTIONS  
SERVICE INFORMATION  
25  
Back Cover  
1
 
INTRODUCTION  
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET  
CAREFULLY.  
Your new cooker is guaranteed and will give lasting service. The guarantee is only  
applicable if the cooker has been installed in accordance with the Installation  
Instructions.  
The cooker is designed specifically for domestic use and responsibility will not be  
accepted for use in any other installation.  
When first using the cooker ensure that the room is well ventilated (e.g. open a  
window or use an extractor fan) and that persons who may be sensitive to the odour  
avoid any fumes. It is suggested that any pets be removed from the room until the  
smell has ceased. This odour is due to any temporary finish and also any moisture  
absorbed by the insulation.  
Our policy is one of continual improvement in design and development,  
therefore strict accuracy of illustrations and descriptions cannot be  
guaranteed.  
This appliance conforms to the following EEC Directives:  
Gas Appliances  
90/396/EEC  
Low Voltage Equipment  
72/23/EEC  
93/68/EEC  
Electromagnetic Compatibility  
89/336/EEC  
92/31/EEC  
93/68/EEC  
2
 
FOR YOUR SAFETY  
Please read the precautions below before using your cooker.  
ALWAYS make sure you understand the controls before using the cooker.  
ALWAYS check that all controls on the cooker are turned off after use.  
ALWAYS stand back when opening oven door to allow heat to disperse.  
ALWAYS use dry, good quality oven gloves when removing items from the  
ovens.  
ALWAYS keep the oven door closed when the cooker is not in use.  
ALWAYS place pans centrally over the hotplate burners and position them so  
that the handles cannot accidentally be caught or knocked or become  
heated by other burners.  
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can  
cause a fire.  
ALWAYS allow the cooker to cool before cleaning.  
ALWAYS follow the basic principles of food handling and hygiene to prevent the  
possibility of bacterial growth.  
ALWAYS turn off the electricity supply before cleaning or replacing the oven  
lamp.  
ALWAYS refer servicing to CORGI registered appliance service engineers.  
3
 
FOR YOUR SAFETY  
NEVER leave children unsupervised where the cooker is installed as all surfaces  
will get hot during and after use.  
NEVER allow anyone to sit or stand on any part of the cooker.  
NEVER store items that children may attempt to reach above the cooker.  
NEVER heat up unopened food containers as pressure can build up causing  
the container to burst.  
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker,  
or in cabinet immediately above or next to the cooker.  
NEVER fill a deep fat frying pan more than 1/3 full of oil, or use a lid. DO NOT  
LEAVE UNATTENDED WHILE COOKING.  
NEVER place flammable or plastic items on or near the hotplate.  
NEVER use proprietary spillage collectors on the hotplate.  
NEVER use the cooker as a room heater.  
NEVER dry clothes or place other items over or near to the hotplate or oven/grill  
doors.  
NEVER wear garments with long flowing sleeves whilst cooking.  
NOTE: The use of a gas cooking appliance results in the production of heat and  
moisture in the room in which it is installed. Always ensure that the kitchen is well  
ventilated; keep natural ventilation holes open or install a mechanical ventilation  
device (mechanical extractor hood).  
In particular when using the grill or more than one hotplate burner, open a window if  
a mechanical ventilation device is not operating.  
4
 
USER’S INSTRUCTIONS  
Grill Top Cover  
Grill Cover  
Side Panels  
Timer  
Grill Pan  
Grill Pan  
Grid  
Grill Shelf  
Splashback  
Splash Back  
Side Trim  
Pan Supports  
Hotplate  
Top  
Hotplate  
Burners  
Control  
Knobs  
Hotplate Control  
Fascia  
Outer  
Side Panel  
Oven Door  
Handle  
Ignition Button  
Oven Door  
Glass Panel  
Storage  
Compartment  
Plinth Panel  
5
 
OVEN TIMER OPERATION  
The oven timer offers you the following features:  
1. Time of Day  
2. Automatic Cooking  
3. Minute Minder  
AUTOMATIC COOKING  
The main oven can be controlled automatically.  
GUIDANCE ON AUTOMATIC COOKING  
1. Select foods which will take the same time to cook.  
2. Set the oven timer so that the food has just finished or is just about to finish  
cooking on your return to the oven. This will ensure the food has not cooled  
down and does not require reheating before serving.  
3. Food should be as cold as possible when it goes into the oven, ideally  
straight from the refrigerator. Frozen meat and poultry should be thawed  
thoroughly before it is put in the oven.  
4. We advise that warm food should never be placed in the oven if there is to be a  
delay period. Stews prepared by frying the meat and vegetables should be  
cooked as soon as possible.  
5. We advise dishes containing left-over cooked poultry or meat, for example  
Shepherds Pie, should not be cooked automatically if there is to be a delay  
period.  
6. Stews and joints should be cooked by the long slow method, so that the delay  
period is kept to a minimum.  
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,  
joints, etc) the delayed start should be kept to a minimum.  
8. Wine or beer may ferment and cream may curdle during the delay period, so it  
is best to add these ingredients just before serving.  
9. Foods which discolour should be protected by coating in fat or tossing in water  
to which lemon juice has been added, prior to placing food in the oven.  
10. Dishes containing liquid should not be filled too full to prevent boiling over.  
11. Food should be well sealed (but not airtight) in a container to prevent the loss  
of liquid during cooking. Aluminium foil gives a good seal.  
12. Ensure food is cooked thoroughly before serving.  
TIMER OPERATION  
1. make sure all oven controls are turned OFF.  
2. Check that the electricity supply to the cooker is turned ON.  
3. Check that the timer is set to the correct time of day.  
6
 
KNOW YOUR TIMER  
CLOCKFACE  
The timer incorporates a 24 hour clock.  
Ensure correct time of day is always set, before using your cooker.  
PLEASE NOTE THAT THE DISPLAY WILL DIM BETWEEN 22.00  
HOURS AND 06.00 HOURS TO PREVENT GLARE.  
However, should you operate the timer during these hours the display will  
return to normal brightness for a few seconds and then dim again.  
SYMBOLS  
will light up when you select a Minute Minder Period and will remain  
lit for the period set. At the end of the Minute Minder Period, the timer  
will emit an audible tone for 2 minutes, the symbol will start to flash  
and will continue to flash until the Minute Minder function is cancelled.  
This “Cookpot” symbol will light up either:–  
– When you press the Cook Period Button and set a length of time for  
an Auto Cooking Programme. (It will go out again a few seconds after  
you release the timer buttons).  
– During the actual Cook Period.  
Minute Cook End  
Minder Period Time  
Manual  
“AUTO” will light up:–  
– When the timer is first turned on it will flash. (It will go out when a  
time of day is set.  
A
U
T
O
– When an Auto Cooking Programme has been set.  
The “Auto” symbol will flash at the end of an Auto Cooking programme  
to indicate that the programme has finished.  
Minute Cook End  
Minder Period Time  
Manual  
(When the “Auto” symbol is flashing, to return the oven to Manual  
operation, turn the oven controls off, ensure that the correct time  
of day is set, and press the “Manual” button twice – The “Auto”  
symbol will go out.  
TIMER FUNCTION BUTTONS  
Minute Minder  
Button  
Here you can set a time period of up to 23 hours 59 minutes, that will count down.  
When it reaches zero, the timer will emit an audible tone.  
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.  
AUTO COOKING PROGRAMME  
Cook Period Button  
Cook Period is the actual length of time for which, the timer will switch the oven(s)  
on as part of an “Auto Cooking” programme.  
(e.g. If you set 2 hours, the food will be cooked for 2 hours).  
The time of day at which you want an “Auto Cooking” programme to end.  
End Time Button  
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The  
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will  
hear a audible tone at 11:00, to indicate that the Auto  
Cooking Programme has finished.  
Notes:  
– When setting an Auto Cooking programme you will need to set the oven con-  
trols(s) to the required temperature(s) when you set the timer.  
_ If an Auto Cooking programme has been set the oven(s) will only operate during  
the pre-programmed time.  
Manual Button  
Needs to be pressed to cancel an Auto Cooking programme and return the  
ovens(s) to Manual operation.  
“+” and “–” Buttons  
Used to adjust the various timer function settings.  
7
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
SETTING THE TIME OF DAY  
A
U
Step 1 Make sure all oven controls are turned Off.  
T
O
Step 2 Check the electricity supply to the cooker is turned on.  
Minute Cook End  
Minder Period Time  
Step 3 When switched on the display will show 0.00 and Auto symbol  
Manual  
will be flashing intermittently.  
Step 4 Press & hold in both the “Minute Minder” & “Cook Period” button  
together.  
Step 5 With the “Minute Minder” & “Cook Period” buttons still held in,  
press either the “+” or “–” buttons to set the correct time of day.  
Minute Cook End  
Minder Period Time  
Manual  
Step 6 Release all the buttons simultaneously.  
THE TIME OF DAY IS NOW SET.  
To change the time of day repeat Steps 4, 5 & 6 above.  
Note: You cannot adjust the time of day if the timer has been set  
for an Auto Cooking Programme.  
Bell Symbol  
SETTING THE MINUTE MINDER  
Step 1 Ensure the time of day is set correctly.  
Step 2 Press and hold the Minute Minder Button, a symbol will light up.  
Step 3 With the “Minute Minder” button held in, set the required Minute  
Minute Cook End  
Minder Period Time  
Minder time using the “+” and “–” buttons.  
Manual  
Release all buttons and the timer display will revert back to the time of day.  
Bell symbol will remain lit to signify that a Minute Minder period has been set.  
At the end of the set time a bleeping sound will be heard, and the  
symbol will flash for approximately 2 minutes.  
After approximately 2 minutes the bleeping sound will stop and the  
symbol will go out automatically.  
Minute Cook End  
Minder Period Time  
Manual  
Step 4 To cancel the bleeping sound within the two minutes press the  
Minute Minder button.  
Note 1 When the Minute Minder has been set, the time remaining can be  
checked at any time by simply pressing the Minute Minder button.  
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds  
by pressing and holding the Minute Minder button and then at the same  
time pressing the “–” button until 0.00 appears in the display window.  
8
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
AUTO COOKING PROGRAMMES  
There are two Auto Cooking programmes that can be selected using your timer:–  
(a) To set the timer to switch the oven(s) On and Off Automatically  
(b) To set timer to switch on immediately and OFF automatically after a set cook period.  
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY  
This allows you to cook at a specified time for a chosen period before the oven  
switches off Automatically.  
Step 1 Check that the correct time of day is set, if not follow instructions for setting the  
time of day.  
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).  
Cooktop Symbol  
Step 3 Press and hold in the Cook Period button.  
The display will read 0.00 with the cookpot ( ) symbol lit.  
Step 4 With the Cook Period button still held in, set the required Cook  
Period using the “+” and “–” buttons.  
Minute Cook End  
Manual  
Minder Period Time  
A
Release the buttons and the timer display will revert to the time of day  
with the Auto symbol and Cookpot ( ) symbol lit.  
U
T
O
Step 5 Press and hold in the “End Time” button.  
A
U
The display will read the earliest possible end time for the Cook  
T
O
Period that you have set above.  
The Auto symbol and Cookpot ( ) symbol lit.  
Step 6 With the End Time button still held in, use the “+” and “–”  
Minute Cook End  
Minder Period Time  
Manual  
buttons to set the “End Time” (i.e. The time you require the oven  
to switch off).  
Release all the buttons and the timer will revert back to the time of day.  
A
U
The “Auto” symbol will remain lit to signify that an Auto Cooking  
Programme has been set. The ( ) symbol will go out.  
T
O
Step 7 Turn the oven control(s) to the required temperature, and if  
Minute Cook End  
Manual  
Minder Period Time  
necessary select the appropriate oven function.  
Note: If your appliance has two ovens: When the timer has been  
set for one oven it is possible to use the other oven only during the same  
Automatic programme.  
At the end of the Automatic Cook Period the Auto Symbol will flash and  
an intermittent bleeping sound will be heard.  
The bleeping sound will continue for approximately 2 minutes unless  
cancelled. The “Auto” symbol will continue to flash until the timer is  
returned to Manual operation (see below).  
Step 8 Press the Manual button to cancel the bleeping sound. (If 2  
minutes has not elapsed).  
Minute Cook End  
Minder Period Time  
Manual  
Step 9 Turn the oven control(s) to the OFF position.  
Step 10 Press the manual button again to return the oven(s) to Manual  
Operation. (The Auto symbol will go out)  
9
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
Note 1 When cooking automatically the Cook Period can be checked at any time  
by simply pressing the Cook Period button.  
Note 2 When cooking automatically the End Time can be checked at any time by  
simply pressing the End Time button.  
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY  
AFTER A SET COOK PERIOD  
Step 1Check that the correct time of day is set, if not follow instructions for setting the time of day.  
Step 2Place food onto the correct shelf position in the oven and close the oven door(s).  
Step 3Turn the oven control(s) to the required temperature, and if necessary select the appropriate  
oven function.  
Cookpot Symbol  
Step 4 Press & hold in the “Cook Period” button, the display will read  
0.00 and the cookpot ( ) symbol will light up.  
With the Cook Period button still held set the required Cook Period  
using the “+” and “–” buttons. Example: 1hr 30 minutes (as shown).  
Minute Cook End  
Minder Period Time  
Manual  
Note: Cook Period is the length of time the food requires to cook.  
Step 5 Release all buttons.  
A
U
The timer display will revert to the time of day with the Auto symbol lit &  
Cookpot symbol remaining lit.  
T
O
Note: Cookpot symbol disappears  
At the end of the Cook Period the “Auto” symbol will flash and an  
A
intermittent bleeping sound will be heard.  
U
The bleeping sound will continue for approximately 2 minutes unless  
T
O
cancelled. The “Auto” symbol will continue to flash until the timer is  
returned to Manual operation (see below).  
A
Step 6 Press the manual button to cancel the bleeping.  
U
(If 2 minutes has not elapsed)  
T
O
Minute Cook End  
Manual  
Minder Period Time  
Step 7 Turn the oven control(s) to the OFF position.  
A
Step 8 Press the “Manual” button again to return the cooker to Manual  
operation. (The Auto symbol will go out).  
Minute Cook End  
Minder Period Time  
Manual  
10  
 
ELECTRONIC CLOCK & AUTOMATIC OVEN  
TIMER OPERATION  
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE  
THE COOK PERIOD HAS FINISHED.  
Step 1 Turn the oven control(s) to the OFF position.  
Step 2 Press and hold in the “Cook Period” button.  
Minute Cook End  
Minder Period Time  
Manual  
Step 3 With the “Cook Period” button still held in, return the display to  
0.00 by pressing the “–” button.  
A
U
T
Step 4 Release the “Cook Period” and “–” buttons and the display will  
O
revert to the time of day and the “Auto” symbol will flash.  
Step 5 Press the “Manual” button to return the oven(s) to “Manual”  
operation. The “Auto” symbol will go out.  
Minute Cook End  
Minder Period Time  
Manual  
Note 1  
When cooking automatically the Cook Period can be checked at any time by  
simply pressing the Cook Period button.  
OTHER NOTES ON TIMER OPERATION  
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the  
Cook Period button.  
2. When cooking Automatically the End Time can be checked at any time by simply pressing the  
End Time button.  
3. Having set a Cook Period and End Time an electronic device stores the information. The device  
within the timer will switch the oven(s) on and off at the required times.  
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–  
(a) Press and hold in the “Cook Period” button.  
A
U
(b) With the Cook Period button still held in, return the display to  
by pressing the “–”  
T
O
button.  
(c) Release the “Cook Period” & “–” buttons, and the display will revert to the time of day and  
the “Auto” symbol will flash.  
(d) Press & release the “Manual” button.  
(e) Start the sequence again.  
5. If at any time the display shows three flashing zero’s 0.00. It is likely that the electricity supply  
to the oven has been interrupted. Reset the timer to the correct time of day.  
Food in the oven may, therefore, not have been cooked, before serving check food is  
thoroughly heated and completely cooked.  
6. To set each function always press and hold the required function button and at the  
same time press “+” or “–” buttons.  
Note: Between the hours of 22.00 & 06.00 the display dims to prevent glare.  
However, if you should operate a button during this period, the timer will return to  
normal brightness for a few seconds and then dim again.  
11  
 
HOTPLATE  
The hotplate has two high speed burners and two simmering burners which will  
accommodate pans between 100mm (4”) and 230mm (9”) diameter. All pans should  
be positioned centrally over the burners.  
Simmering aids such as steel plates should not be used because they can cause  
damage to the pan supports.  
TO USE THE HOTPLATE  
1. Check that the electricity supply is turned on.  
2. Push in and turn the control knob of the  
chosen burner anti-clockwise to the large flame symbol. Continue to press  
the ignition button until the sparks light the gas.  
3. Turn the control knob anti-clockwise to the desired setting.  
Only turn the control knob between the large flame symbol and the small  
flame symbol for adjusting the setting.  
4. To turn off, turn the control knob fully clockwise to the symbol G  
DO NOT use mis-shapen pans which may be unstable.  
DO NOT use round base woks directly on the pan supports.  
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of  
the burners every time they are used, the ignitors must be kept clean and dry. Remove  
any food spillage or cleaning materials from the ignitor using a small nylon brush such  
as a tooth brush. Access to the ignitor can be achieved by lifting off the loose burner  
parts carefully when the burners are cool.  
When the hotplate burner bodies and caps are removed for cleaning, be careful not to  
drop any food particles or cleaning materials into the burner bases, to avoid the possi-  
bility of blocking the gas jets.  
If aluminium based pans are used, a silvery deposit may appear on the top edge of the  
pan support fingers. See ‘Care and Cleaning’ section for cleaning information.  
When the hotplate burners are turned down, a slight ‘popping’ noise may be heard. This  
is perfectly normal.  
12  
 
HOTPLATE  
SAFETY REQUIREMENTS FOR DEEP FAT FRYING  
1. Never fill chip pans more than one third full with oil or fat.  
2. Never leave oil or fat unattended during the heating or cooling period.  
3. Never heat fat or fry with a lid on the pan.  
4. Always dry food thoroughly before frying, and lower it slowly into the  
hot oil or fat. Frozen foods in particular will cause frothing and spitting if  
added too quickly.  
5. Always keep the outside of the pan clean and free from streaks of oil or fat.  
HOW TO DEAL WITH A FAT FIRE  
1. Do not move the pan.  
2. Turn off the hotplate burners.  
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire.  
Do not use water or a fire extinguisher as the force of it may spread the  
burning fat or oil over the edge of the pan.  
4. Leave the pan for at least 60 minutes before moving it.  
13  
 
THE GRILL  
The high level grill is fitted with a grill pan carrier that provides two grilling  
levels. The grill pan can be pulled out to safety stops for viewing and for turning the  
food. To remove the pan: pull it forward to the stop, lift it upwards and remove  
outwards.  
TO USE THE GRILL  
1.  
2.  
3.  
Check that the electricity supply is switched on.  
Insert the grill pan in the required position.  
Push in and turn the control knob anti - clockwise to the large flame  
symbol. Press the ignition button until the spark lights the gas.  
Turn the control knob anti - clockwise to the desired setting. Only turn the  
control knob between the large flame symbol and the small flame symbol  
for adjusting the setting.  
4.  
5.  
To turn off, turn the control knob fully clockwise to the symbol G.  
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat,  
intensify the heat and create a fire hazard.  
Grilling can be started from cold but for best results preheat for approximately two  
minutes. Most cooking is done with the heat full on but it may be desirable to reduce  
it for thicker pieces of meat, fish, chicken portions or for keeping food warm.  
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska,  
place the dish on the grill shelf. The base of the grill pan can be used for warming fruit  
garnishes on the reduced setting.  
NOTE: Strong detergents used in dishwashers may damage the grill pan grid  
finish; clean in soapy water as described in CARE AND CLEANING section.  
PLATE RACK  
A plate rack can be obtained as an optional  
extra from your local Cannon Spares Centre.  
(See Back Cover)  
Fitting instructions are supplied with the  
plate rack.  
14  
 
OVEN  
The oven has different heat zones – the thermostat settings refer to the temperature  
on the middle shelf position; above this shelf it is hotter and below it is cooler. Two  
shelves provide five possible cooking levels enabling full use of the different  
temperatures inside the oven.  
Each shelf has a safety stop to prevent if from being pulled out too far when attending  
to food. Shelves are removed from the oven by pulling them out to the stop and then  
lifting them at the front to withdraw.  
The maximum size of baking tray that should be used is 300mm x 350mm  
(12” x 14”).  
TO USE THE OVEN  
1.  
Check that the electricity supply is switched on and the timer is set to  
manual mode.  
2.  
3.  
Place oven shelves in the chosen positions (refer to cooking charts).  
Push in and turn the oven control knob fully anti-clockwise. Sparking  
will continue until the burner is lit.  
4.  
5.  
Turn the control knob clockwise to the required setting (refer to cooking  
chart). There is a delay of about one minute whilst the safety device  
operates before the burner comes on full.  
To turn off, turn the control knob fully clockwise to the symbol G.  
NEVER leave the oven door open for long periods as this could cause damage to the  
control knobs.  
Never place dishes on the oven base over the burner.  
An odour may be noticed when first using the oven – this should cease after a short  
period of use.  
COLD START COOKING  
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be  
put into a cold oven. Satisfactory results can also be obtained with creamed mixture,  
rich pastries or yeast mixtures, but for perfection we recommend  
oven for about 15 minutes.  
preheating the  
ROASTING OF LARGE POULTRY  
The maximum weight of turkey that can be accommodated is 25lbs (11.5kg)  
provided it is of suitable shape.  
It is important to check that the bird DOES NOT overhang the burner at the back of the  
oven.  
15  
 
OVEN  
THE ‘E’ SETTING  
This is used for slow cooking, keeping food warm and warming plates for short  
periods.  
USING THE ‘E’ SETTING FOR SLOW COOKING  
1. All dishes cooked by the ‘E’ setting should be cooked for a minimum of 6 hours.  
They will ‘hold’ at this setting for a further hour but marked deterioration in  
appearance will be noticed in some cases.  
2. Joints of meat and poultry should be cooked at Mk 6 for 30 minutes before  
turning to the ‘E’ setting and never be cooked lower than the middle shelf  
position.  
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2kg) should not be  
cooked using the ‘E’ setting.  
4. Always stand covered joints on a rack over the meat tin to allow good air  
circulation.  
5. Pork joints and poultry must be checked for an internal temperature of at least  
88°C using a meat thermometer.  
6. This method is unsuitable for stuffed meat and poultry.  
7. Always bring soups, casseroles and liquids to the boil before putting in the oven.  
8. Cover casseroles with foil and then the lid to prevent loss of moisture.  
9. Always thaw frozen food completely before cooking.  
10. Root vegetables will cook better if cut into small pieces.  
11. Adjust seasonings and thickenings at the end of the cooking time.  
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be  
cooked lower in the oven whilst other dishes requiring greater heat can be  
cooked above them.  
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day  
cooking sessions, when they can be observed from time to time.  
14. Dried red kidney beans must be boiled for a minimum of ten minutes after  
soaking, before inclusion in any dish.  
REPLACEMENT OF OVEN LIGHT BULB  
Light bulbs are not covered by the manufacturer’s guarantee.  
A new 25W, 300°C rated SES bulb can be obtained from your cooker supplier or any  
major electrical retailer.  
1. Disconnect the electricity supply to the cooker and remove the shelves from the  
oven.  
2. Unscrew the lens using a thick cloth to your protect fingers in the unlikely event  
of a lens fracture.  
3. Unscrew bulb.  
4. Fit new bulb and refit lens.  
16  
 
STORAGE & REHEATING OF FOOD  
STORAGE AND RE-HEATING OF FOOD  
It is vitally important to strictly adhere to the basic principles of food handling and  
hygiene to prevent the possibility of bacterial growth.  
1. If food is to be frozen or not served immediately, cool it in a clean container  
as quickly as possible.  
2. Completely thaw frozen food in the refrigerator before re-heating.  
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven,  
mk 6, and then serve immediately.  
4. Only re-heat food once.  
‘COOK CHILL’ DISHES  
These should always be placed in a pre-heated oven ideally on the first or  
second shelf position. Follow the packet instructions for cooking time.  
17  
 
OVEN COOKING CHART  
The following times and setting are for guidance only. You may wish to alter the setting to give a  
result more to your satisfaction. When a different setting to that shown below is given in a recipe, the  
recipe instructions should be followed. Allow 15 minutes preheat for best results. Always turn the  
thermostat knob to Mark 9 before selecting the appropriate Gas Mark. Shelf position 1 is the highest.  
Gas  
Mark  
Shelf  
Positions  
Food  
Approx. Cooking Time and Comments  
STARTERS  
Patés and Terrines  
FISH  
1
2
3 or 4  
4
1 / - 2 hrs  
25 mins - 1 hr, depending on recipe  
and size of fish  
Oily Fish (whole)  
4 or 5  
4 or 5  
3
3
White Fish (fillets & steaks)  
25 - 30 mins.  
MEAT AND POULTRY  
Veal  
5
4
25 mins per lb + 25 mins  
Beef  
4 or 5  
4
25 - 30 mins per lb + 25 mins  
40 mins per lb covered in foil  
+ 40 mins per lb uncovered  
Ham  
5
4
Lamb  
5
4
30 - 35 mins per lb + 30 mins  
40 mins per lb + 40 mins  
25 mins per lb + 25 mins  
25 mins per lb + 25 mins  
15 - 20 mins per lb + 20 mins  
Pork  
5
4
4
Chicken  
Duckling & gosling  
Turkey  
5
5
4 or 5  
6
4
4 or 5  
4
50 mins. Remove bacon for last 15 mins.  
Add extra 15 mins if roasting brace  
Game birds  
Casseroles  
1
2
3
3 or 4  
1 / - 6 hrs. (depending on type of meat)  
PUDDINGS  
1
1
4
2
2 / - 2 / hrs on a baking tray and  
Milk Puddings  
3
3 or 4  
started with warm milk  
Baked Custard  
3
3 or 4  
45 mins in bain-marie  
40 - 50 mins  
Baked sponges  
4
3
30 - 45 mins depending on the size  
and type of apples  
Baked Apples  
3
1
4
4 or 5  
3
Meringue puddings  
Apple Pie 1x9" (230mm)  
Fruit crumbles  
15 mins or until 'tinged' with brown  
45 - 55 mins on a baking tray  
35 - 45 mins  
6
5 or 6  
3
If using aluminium foil:  
1. Remember it is important to increase the cooking time by one third.  
2. Never allow the foil to touch the sides of the oven.  
3. Never cover the oven interior with foil.  
4. Never cover the oven shelves with foil.  
18  
 
OVEN COOKING CHART  
Gas  
Mark  
Shelf  
Food  
Positions  
Approx. Cooking Time and Comments  
CAKES, PASTRIES AND BISCUITS  
Small cakes - 2 trays  
5
5
4
5
2
4
2
6
5
7
2 & 4  
2 or 3 only  
2 & 4  
2
17 - 25 mins  
"
- 1 tray  
Victoria sandwich 2x8" (205mm)  
25 - 35 mins  
Fatless sponge 2x7" (180mm) -  
3 egg mix  
20 - 25 mins. 2 tins side by side  
1
2
Christmas cake  
3 or 4  
3
4 - 6 / hrs depending on recipe  
1
1
4
2
Madeira cake 7" (180mm)  
Rich Fruit cake 9" (230mm)  
Shortcrust pastry  
1 / - 1 / hrs  
1
2
3
3 - 3 / hrs.  
2 or 3  
2
15 mins - 1 hr depending on recipe  
20 - 40 mins depending on recipe  
10 - 30 mins depending on recipe  
Rich Shortcrust pastry - 1 tray  
Flaky & puff pastry - 2 trays  
- 1 tray  
1 & 3  
2 or 3  
2
"
"
"
"
Choux pastry - éclairs 1 tray  
Scones - 2 trays  
6
7
35 - 40 mins  
10 - 15 mins  
"
2 & 4  
2 or 3  
4
- 1 tray  
Shortbread - 7" (180mm) round  
Biscuits - 2 trays  
2
4
55 - 1hr depending on thickness  
15 - 20 mins depending on recipe  
1 and 3  
2 or 3  
- 1 tray  
"
"
"
"
YEAST MIXTURES  
Bread  
7 or 8  
7 or 8  
5
3 or 4  
2 or 3  
2 or 3  
45 - 50 mins  
15 - 20 mins  
30 - 40 mins  
Rolls  
Chelsea buns  
MISCELLANEOUS  
Yorkshire Pudding - large  
7
7
1 or 2  
1 or 2  
3
45 - 50 mins  
25 - 30 mins  
30 mins  
- individual  
Soufflés  
4
2 - 5 hrs starting on shelf 4 until 'set'  
and then on the baseplate until dried  
out - turn when necessary.  
4 &  
baseplate  
Meringues  
'E'  
1
2
Baked Potatoes  
4 or 5  
3
1 / - 3 hrs until soft, depending on size  
When baking with two trays or tins on two levels, the top tray is removed first and the lower tray  
moved up to the top position for a few minutes longer.  
Soft Margarine – Use the oven settings recommended by the margarine manufacturer and not those  
indicated on the cooking chart.  
 
19  
CARE AND CLEANING  
Switch off the electricity supply before cleaning the cooker.  
Clean the cooker regularly and wipe up spills after they occur to prevent them  
from becoming burnt on. Never use biological washing powder,  
caustic cleaners harsh abrasives, scouring pads, aerosol cleaners or oven chemi-  
cal cleaners of any kind.  
To move the cooker forward, open the oven door and with both hands positioned  
under the roof of the compartment lift and pull forward. Replace by pushing the cook-  
er backwards. Check that the cooker is level. Take care to ensure that any floor cover-  
ing is not damaged.  
OVEN HEAT CLEAN LININGS  
The oven roof, back and side linings are coated with a special enamel which has a  
continuous cleaning action. The higher the oven temperature the more effective the  
action. In most cases this cleaning operation will proceed during normal cooking.  
However, if roasting is done frequently, or high temperatures are not used regularly, it  
may be necessary to run the oven empty at Mark 8 for about two hours.. If desired,  
they can be wiped with a cloth wrung out in hot soapy water followed by a clean  
damp cloth.  
OVEN DOOR  
The inner glass panel can be removed for easy cleaning. Unscrew the two screws  
securing the glass panel, taking care not to allow the glass to fall. The glass panel can  
then be washed at the sink. Refit the glass panel according to the instruction on it.  
Warning: The oven must not be operated with the inner glass panel removed.  
20  
 
CARE AND CLEANING  
COOKER PART AND FINISH  
CLEANING METHOD  
Vitreous Enamel  
Grill cover top  
Splash back  
Hotplate control fascia  
Hotplate top  
Pan supports  
Burner caps  
Roasting tin  
Grill pan  
Clean with a cloth wrung out in hot  
soapy water.  
Stubborn stains can be removed with  
a cream, paste or liquid cleaner or by  
gently rubbing with well moistened,  
liberally soaped very fine steel wool  
pads e.g. Brillo, Ajax etc.  
Check that the cleaning agent used is  
approved by the Vitreous Enamel  
Development Council.  
Oven baseplate  
Inside of the oven door  
Paint  
Grill cover side panels  
Grill fascia  
Wash with a cloth wrung out in hot  
soapy water only.  
DO NOT USE ABRASIVES  
Oven door sides  
Splash back side trims  
Outer side panels (oven)  
Storage drawer & Handle  
Aluminium  
Burner bodies  
Use a nylon brush to remove any cleaning  
materials, water or dirt from the hotplate burner  
burner bodies.  
Glass  
Oven door panel  
Grill fascia  
As for enamel cleaning above.  
Polish with a clean dry cloth or  
kitchen roll.  
21  
 
CARE AND CLEANING  
COOKER PART AND FINISH  
CLEANING METHOD  
Chromium plated  
Oven shelves  
Grill shelf  
Grill pan handle supports  
Grill pan grid  
Wipe with a cloth wrung out in hot  
soapy water. A liberally soaped very  
fine steel wool pad e.g. Brillo, Ajax  
etc., or a chrome or stainless steel  
cleaner may be used.  
Plate rack (optional extra)  
Plastic  
Grill fascia side cheeks  
Grill pan handles  
Control knobs and buttons  
Oven door handle  
Wipe with a cloth wrung out in hot  
soapy water.  
Stubborn stains may be removed with  
a cream cleaner, carefully applied  
22  
 
SOMETHING WRONG  
WITH YOUR COOKER  
Before contacting your Service Centre or Installer, check the problem guide  
below, there may be nothing wrong with your cooker.  
PROBLEM  
CHECK  
If all burners fail to ignite:  
Check that sparks appear at the burners; a clicking  
noise should be heard.  
Ignition does not work.  
Oven burner  
If not  
Check that the electricity supply is turned on.  
If the electricity supply has failed, the hotplate  
burners and grill can be lit by a match.  
If only one burner fails to ignite:  
Burner ports  
Ignitor  
Check that the burner is dry and that spillage of food  
or cleaning fluid remains are not affecting the ignitor  
or burner ports.  
Grill burner  
Clean away any debris with a dry nylon brush such as  
an old toothbrush. If a wire wool pad has been used  
for cleaning around the burner ensure the ignitor is  
free from any stray strands. Any water on the burner  
should be dried with a cloth or kitchen towel.  
Ignitor  
Burner ports  
Hotplate burner.  
On the hotplate make sure that all the burner parts  
are correctly seated.  
Burner ports  
Ignitor  
23  
 
SOMETHING WRONG  
WITH YOUR COOKER  
PROBLEM  
CHECK  
Slight odour or small  
amount of smoke when  
grill / oven used first  
time  
This is normal and should cease after a short period.  
Check that the gas mark and shelf positions are as recom-  
mended in the Oven Cooking Charts. However, it may be  
necessary to increase or decrease the recommended  
setting slightly to suit your taste.  
Oven cooks too fast or too  
slow  
The electricity supply to the cooker may have been been  
interrupted, but has now come back on again. Set the cor-  
rect time of day by following the instructions given in the  
timer section of this book.  
Timer Display shows "0:00"  
with "Auto" Flashing.  
Oven does not work, but the  
grill and hotplate burners do  
work.  
Ensure that the timer is set to the correct time of day.  
Ensure that the timer is set to manual mode by pressing  
the ‘Manual’ button until the ‘Auto’ symbol is off.  
Cannot set an “Auto Cook”  
programme or cannot get the  
timer to turn the oven on or  
off at the required times.  
The ‘Cook period” button on the timer refers to the  
duration of cooking (the time required to cook the food).  
When you have set the required ‘Cook period’ and ‘end  
time’ the timer will calculate the start time for you.  
The oven lamp is not covered by the guarantee. The part  
is easily changed (see the section on oven lamp replace-  
ment) A new lamp may be obtained from our Spare Parts  
department by calling: 0541 530530  
Oven lamp does not work  
DISPOSAL OF YOUR PRODUCT:  
To minimise the risk to injury to children please dispose of your product carefully and safely.  
Remove all doors and lids (where fitted). Remove the mains cable (where fitted) by cutting off  
flush with the appliance and always ensure that no plug is left in a condition where it could be  
connected to the electricity supply.  
To help the environment, Local Authority instructions should be followed for the disposal of  
your product.  
24  
 
INSTALLATION INSTRUCTIONS  
Prior to installation, ensure that the local distribution conditions (nature of the gas and  
gas pressure) and the adjustment conditions are compatible. The adjustment condi-  
tions for this appliance are stated on the data badge which is fitted below the oven  
door.  
This appliance is not designed to be connected to a combustion products evacuation  
device. It must be installed and connected in accordance with current installation reg-  
ulations. particular attention should be given to the relevant requirements regarding  
ventilation.  
MODEL NUMBERS 10390G Mk2 AND 10395G Mk2  
Category I2H (GB. IE)  
These models are set to burn NATURAL GAS (G20) at 20 mbar ONLY and can not be  
used on any other gas.  
GAS SAFETY (INSTALLATION & USE) REGULATIONS  
It is the law that all gas appliances are installed by competent persons in  
accordance with the current edition of the above regulations. It is in your interest and  
that of safety to ensure compliance with the law.  
In the UK, CORGI registered installers work to safe standards of practice.  
The cooker must also be installed in accordance with BS 6172: 1990.  
Failure to install the cooker correctly could invalidate the warranty liability claims and  
could lead to prosecution.  
LOCATION  
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in  
a room containing a bath or shower. The cooker must not be installed in a bed-sitting  
room of less than 20m3.  
PROVISION FOR VENTILATION  
The room containing the cooker should have an air supply in accordance with  
BS 5440: Part 2: 1989.  
The room must have an opening window or equivalent; some rooms may also require  
a permanent vent. If the room has a volume between 5 and 10m3, it will require an air  
vent of 50cm2 effective area unless it has a door which opens directly to outside. If the  
room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area.  
If there are other fuel burning appliances in the same room, BS 5440: Part 2: 1989  
should be consulted to determine air vent requirements.  
25  
 
TECHNICAL DATA  
Dimensions:  
Height  
1460mm  
Width  
538mm  
Depth  
Height to Hotplate  
590mm Excluding Handles  
900mm  
General  
Gas connection  
Gas supply  
1
1
2
2
Rp / ( / " B.S.P. Female)  
G20 at 20 mbar  
Pressure Test Point  
Gas Rate Adjustment  
Aeration Adjustment  
Grill Injector  
None  
None  
Electric  
Flexible cord fitted with a 3 pin 13 amp plug  
230/240V a.c. 50 Hz, 3A fuse  
NATURAL GAS MODELS  
BURNER  
Hotplate L/H Front R/H Rear  
Hotplate R/H Front L/H Rear  
Grill  
HEAT INPUT  
3.0 kW  
INJECTOR  
134  
1.8 kW  
109  
4.8 kW  
170  
Oven  
2.7 kW  
120  
26  
 
INSTALLATION INSTRUCTIONS  
SPACE FOR FIXING  
The cooker can be close fitted below hotplate level. This requires a minimum  
distance of 540mm between cupboard units of hotplate height.  
Cupboards or walls to the side of the cooker must be 125mm away  
Wall cupboards above hotplate level must also be 125mm away as shown  
Where cupboards or any overhead surfaces are fitted above the cooker allow  
a clearance of 500mm from the top of the grill to the underside of the overhead sur-  
f
500mm MIN  
125mm  
MIN.  
125mm  
MIN.  
540mm MIN  
COOKER HOODS  
If a cooker hood is to be installed, refer to the cooker hood manufactures’ instructions regarding  
fixing height.  
27  
 
INSTALLATION INSTRUCTIONS  
UNPACKING THE COOKER  
Unpack the components. Check that the following parts are present.  
Grill pan, grid & Grill pan carrier  
Baking dish  
Enamelled burner caps (4)  
Aluminium burner bodies (4)  
Pan supports (4)  
Main oven shelves (2)  
Literature  
LEVELLING  
Two rear wheels and two front feet are fitted which can be adjusted up or down to set  
the height (900mm - 915mm) and level the cooker.  
1.  
The rear wheels can be raised or lowered from the BACK of the cooker by  
adjusting the levelling screws ‘A’ in the plinth.  
The front feet can be simply screwed in or out to lower or raise the front of the  
cooker.  
2.  
CAUTION: Some soft floor coverings may get damaged if the cooker is not moved  
carefully.  
STABILITY BRACKET  
The back of the cooker has a slot for engagement of a stability bracket, which can be  
obtained, as an extra, from the cooker supplier. The leaflet included with the bracket  
should be read in conjunction with the following instructions.  
Push cooker to its intended position.  
Draw pencil lines on the floor in line with the front and left side of the  
plinth.  
Remove the cooker.  
Position stability bracket in accordance with diagram below and secure to the  
floor.  
Measure height from floor level to the bottom of the slot in the back of the  
cooker.  
Add 3mm to the dimension and assemble the stability bracket to that height.  
(i.e. from floor level to the underside of the top member).  
‘A’  
92  
mm  
‘B’  
410mm  
PENCIL LINE  
28  
 
INSTALLATION INSTRUCTIONS  
FIT GRILL PAN CARRIER  
1.  
2.  
3.  
Carefully locate the grill pan carrier under the grill canopy at the front. DO  
NOT ENGAGE IT IN THE SLOT.  
Support the carrier, swing it upwards at the rear and locate it in the holes  
in the splashback.  
Locate the front pegs of the carrier into the slots at the front of the  
grill. Carefully pull the carrier downwards until it locks into position.  
3. LOCATE FRONT PEGS OF  
CARRIER INTO  
SLOTS AT FRONT OF  
1. LOCATE UNDER  
GRILL AND PULL CARRIER  
GRILL FRAME  
DOWN UNTIL LOCKED INTO  
DO NOT ENGAGE  
POSITION.  
IN SLOT.  
SPLASHBACK HOLE  
LOCATION  
2. SWING REAR OF ASSEMBLY  
UPWARDS AND  
LOCATE IN HOLES IN  
SPLASHBACK  
FRONT PEG  
LOCATION SLOTS  
GRILL CANOPY  
REAR PEG  
FRONT ARMS  
LOCATION  
HOLES  
GRILL PAN CARRIER  
SPLASHBACK  
29  
 
GAS CONNECTION  
CONNECTING TO THE GAS SUPPLY  
The cooker is designed to match the depth of standard 600mm work tops. An  
adaptor backplate should, therefore, be fitted within the shaded area shown in to  
allow the cooker to be pushed fully to the wall. If a forward facing backplate elbow is  
used it must be chased into the wall.  
75  
225  
540  
CONNECTING TO GAS SUPPLY  
Connection to the appliance should be made with an approved appliance  
flexible connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of  
hose chosen should be such that when the cooker is in situ, the hose does not touch  
the floor.  
The temperature rise of areas at the rear of the cooker that are likely to come in  
contact with the flexible hose do not exceed 70°C.  
30  
 
ELECTRICAL CONNECTION  
WARNING – THIS APPLIANCE MUST BE EARTHED.  
CONNECT TO A 230-240V A.C. SUPPLY ONLY.  
Connection to the electricity supply should be made via a properly earthed, readily accessible  
wall socket which is adjacent to, and not more than 1.25m away from the appliance and capable  
of electrical isolation.  
Should this plug not fit the socket outlet in your home it should be cut off and replaced with a  
suitable plug as outlined below.  
WARNING: The removed plug cannot be used for any other appliance and should therefore be  
properly disposed of and not left where children might find it and plug it into a supply socket –  
resulting in a danger of electric shock.  
IF THE FITTED PLUG IS REMOVED  
The flexible mains lead must be correctly connected as below to a three pin plug of not less  
than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which  
is approved to B.S. 1362.  
IMPORTANT: The wires in the mains lead fitted to this appliance are coloured in accordance  
with the following code:  
Green &  
Yellow to  
Earth  
GREEN AND YELLOW – EARTH  
BLUE  
BROWN  
– NEUTRAL  
– LIVE  
Brown to  
Live  
Blue to  
Neutral  
3 Amp  
Fuse  
Cord Clamp  
As the colours of the wires in the mains lead of this appliance may not correspond with the  
coloured markings identifying the terminals in your plug, proceed as follows:– The wire which is  
coloured green and yellow must be connected to the terminal in the plug which is marked with  
the letter E or by the earth symbol  
or coloured green or green and yellow. The wire which is  
coloured blue must be connected to the terminal which is marked with the N or coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with the  
letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely  
retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the  
appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a  
qualified electrician.  
Should the mains lead ever require replacement, it is essential that this operation be carried out  
by a qualified electrician and should only be replaced with a flexible cord of the same size i.e.  
0.75mm2 cross sectional area and temperature rating of 850 C e.g. heat resisting PVC.  
Ensure that the replacement lead is securely clamped and positioned using both the on-board  
clamp and ‘P’ clip, prior to fitting the terminal cover.  
IF A MOULDED PLUG IS FITTED  
In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362  
must be fitted.  
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse  
cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A  
new fuse cover can be obtained from your local Electricity Board. The colour of the correct  
replacement fuse cover is that of the coloured marks or inserts in the base of the plug.  
31  
 
INSTALLATION INSTRUCTIONS  
INSTALLATION AND OPERATIONAL CHECKS  
After installation, check for gas soundness. The supply pressure can be checked at the  
grill injector. Access to the injector is by first removing the grill rear panel (4 screws)  
and the left hand side panel (2 screws). Then remove the 2 fastening screws on the left  
hand side of the burner and slide the burner off the injector.  
Fit the hotplate burner bodies and caps, pan supports and grill pan. Referring to the  
instructions for use where necessary,  
1. Check that the hotplate and grill burners ignite correctly and burn with a  
steady flame. Check for a steady flame on the low setting.  
2. Check that with the oven set to mark 9, the burner ignites at low rate,  
and then increases to full rate within 60 seconds. Leave the oven full on with  
the door closed for 10 minutes, and check that when the control is turned to  
the ‘E’ setting that the flame reduces.  
3. Check the operation of the oven timer and oven light.  
Instruct the user on operation of the cooker.  
32  
 
 
Key Contacts  
Service  
We have the largest appliance manufacturer’s service team in Europe,  
specialists directly employed by us to ensure  
your complete confidence.  
trained  
Repair Service  
UK: 08709 066 066  
Republic of Ireland: 1850 302 200  
You will be asked for the following information:-  
Name, address and postcode.  
Telephone number  
Model / Serial number of the appliance  
Clear and concise details of the query or fault  
Place and Date of purchase  
(Please keep the receipt as evidence will be required when the engineer calls).  
Extended Warranty  
To join: UK 08709 088 088  
Republic of Ireland: 1850 502 200  
Genuine Parts & Accessories  
Mail Order Hotline  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
For further product information 01782 385516  
All Cannon Services are offered as an extra benefit and do not affect your statutory rights.  
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
 

Beko Washer WM85135LW User Manual
BenQ Projector mw814st User Manual
Bolens Lawn Mower 128 250A User Manual
Bowers Wilkins Portable Speaker CDM 9NT User Manual
Brother All in One Printer 7840W User Manual
Brother Sewing Machine CS 8060 User Manual
Bushnell Binoculars 13 7507 User Manual
CDA Convection Oven SV470 User Manual
Chauvet Work Light 1 TRI IP User Manual
Chicago Electric Grinder 97588 User Manual