OAKLEY
Use and Installation Instructions
The cooker must be installed in accordance with the regulations in force
and only used in a well ventilated space.
Read these instructions prior to using the cooker and retain them for
future reference.
Part no. 4966200027-02
INTRODUCTION
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET
CAREFULLY.
Your new cooker is guaranteed and will give lasting service. The guarantee is only
applicable if the cooker has been installed in accordance with the Installation
Instructions.
The cooker is designed specifically for domestic use and responsibility will not be
accepted for use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a
window or use an extractor fan) and that persons who may be sensitive to the odour
avoid any fumes. It is suggested that any pets be removed from the room until the
smell has ceased. This odour is due to any temporary finish and also any moisture
absorbed by the insulation.
Our policy is one of continual improvement in design and development,
therefore strict accuracy of illustrations and descriptions cannot be
guaranteed.
This appliance conforms to the following EEC Directive:
Gas Appliances
90/396/EEC
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
3
FOR YOUR SAFETY
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS make sure you understand the controls before using the cooker.
ALWAYS check that all controls on the cooker are turned off after use.
ALWAYS stand back when opening the oven door to allow heat to disperse.
ALWAYS use dry, good quality oven gloves when removing items from the oven.
ALWAYS take care when removing items from the grill when the oven is on, as
the contents may be hot.
ALWAYS keep the oven and grill doors closed when the cooker is not in use.
ALWAYS place pans centrally over the hotplate burners and position them so
that the handles cannot accidentally be caught or knocked or become
heated by other burners.
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can
cause a fire.
ALWAYS allow the cooker to cool before cleaning.
ALWAYS follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ALWAYS keep ventilation slots clear of obstructions.
ALWAYS refer servicing to CORGI registered appliance service engineers.
ALWAYS turn off the electricity supply before cleaning or replacing the oven lamp.
4
FOR YOUR SAFETY
NEVER . . .
NEVER leave children unsupervised where the cooker is installed as all surfaces
will get hot during and after use.
NEVER allow anyone to sit or stand on any part of the cooker.
NEVER store items that children may attempt to reach above the cooker.
NEVER heat up unopened food containers as pressure can build up causing
the container to burst.
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker,
or in cabinets immediately above or next to the cooker.
NEVER fill a deep fat frying pan more than 1/3 full of oil, or use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
NEVER place flammable or plastic items on or near the hotplate.
NEVER use proprietary spillage collectors on the hotplate.
NEVER use the cooker as a room heater.
NEVER dry clothes or place other items over or near to the hotplate or grill
doors.
NEVER wear garments with long flowing sleeves whilst cooking.
NOTE: The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Always ensure that the kitchen is well
ventilated; keep natural ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood).
In particular, when using the grill or more than one hotplate burner, open a window if a
mechanical ventilation device is not operating.
5
HOTPLATE
The hotplate has one large high speed burner, two normal simmering burners and one
small simmering burner which will accommodate pans between 100mm (4”) and
200mm (8”) diameter. All pans should be positioned centrally over the burners.
The pan supports should be fitted on the hotplate such that the indents along one side
of each pan support are inner-most.
The hotplate lid is fitted with a safety device which cuts off the gas supply to the hot-
plate unless the lid is fully open. Do not use the safety device as a means of controlling
the burners.
TO USE THE HOTPLATE
1. Remove any items or spillage from the top of the lid and then raise it to its fully open
position.
2. Press the ignition button and then push in and turn the control knob of the
chosen burner anti-clockwise to the large flame symbol. Continue to press
the ignition button until the sparks light the gas.
3. Turn the control knob anti-clockwise to the desired setting.
Only turn the control knob between the large flame symbol and the small flame
symbol for adjusting the setting.
4. To turn off, turn the control knob fully clockwise to the symbol O.
DO NOT use the hotplate unless all pan supports are in position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
DO NOT use the glass lid (if fitted) as a working surface.
Each burner is fitted with a spark ignitor for lighting the gas. To ensure rapid lighting of
the burners every time they are used, the ignitors must be kept clean and dry. Remove
any food spillage or cleaning materials from the electrode using a small nylon brush
such as a tooth brush. Access to the electrode can be achieved by lifting off the loose
burner parts carefully when the burners are cool.
When the hotplate burner bodies and caps are removed for cleaning, be careful not to
drop any food particles or cleaning materials into the burner bases, to avoid the possi-
bility of blocking the gas jets.
If aluminium based pans are used, a silvery deposit may appear on the top edge of the
pan support fingers. See ‘Care and Cleaning’ section for cleaning information.
6
HOTPLATE
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil or fat.
Frozen foods in particular will cause frothing and spitting if added too quickly.
5. Always keep the outside of the pan clean and free from streaks of oil or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire. Do not
use water or a fire extinguisher as the force of it may spread the burning fat or oil
over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
7
GRILL
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS IN USE.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
GRILL PAN HANDLE
The grill pan handle is detachable from the pan to facilitate cleaning and
storage.The handle can be fixed as follows:
1. Remove the screw and washer from the grill pan bracket.
2. Tilt the handle over the recess (a).
3. Slide the handle towards the centre of the pan (b).
4. Locate the handle over the bracket (c).
For a fixed handle, replace the screw & washer and ensure they are fully
tightened. If a detachable handle is required, do not replace the screw and
washer.
Warning: Ensure when using grill pan handle in the detachable manner it is
centralised and secure.
A
B
C
TO USE THE GRILL
1. Open the grill door and remove the grill pan.
2. Push in and turn the control knob anti - clockwise to the large flame symbol.
Press the ignition button until the spark lights the gas.
3. Turn the control knob anti-clockwise to the desired setting. Only turn the
control knob between the large flame symbol and the small flame
symbol when adjusting the setting.
4. To turn off, turn the control knob clockwise to the symbol O.
Slide the grill pan along the shelf towards the rear of the grill compartment
until it stops.
An odour may be noticed when first using the grill – this should cease after a short peri-
od of use.
DO NOT use the grill with the door closed.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat,
intensify the heat and create a fire hazard.
RELIGHTING THE BURNER
In the event of the burner flames being accidentally extinguished, turn off the
burner control and do not attempt to re-ignite the burner for at least one minute.
8
GRILL
Grilling can be started from cold but for best results preheat for approximately two
minutes. Most cooking is done with the heat on full, but it may be necessary after seal-
ing the food to reduce the heat as required.
For au gratin dishes eg. Macaroni Cheese and meringue toppings eg. Baked Alaska,
place the dish on the floor of the grill compartment.
The base of the grill pan can be used for warming fruit garnishes on the reduced
setting.
NOTE: Strong detergents used in dishwashers may damage the grill pan grid
finish; clean in soapy water as described in CARE AND CLEANING section.
Always ensure that the grill pan handle is correctly fitted to the grill pan.
9
OVEN
The oven has different heat zones – the thermostat settings refer to the temperature
on the middle shelf position; above this shelf it is hotter and below it is cooler. Two
shelves enable full use of the temperatures inside the oven.
Each shelf has a safety stop to prevent if from being pulled out too far when attending
to food. Shelves are removed from the oven by pulling them out to the stop and then
lifting them at the front to withdraw.
The baking dish and grill pan without the handle can be used in the oven. The
maximum size of baking tray that should be used is 300mm x 330mm (12” x 13”).
TO USE THE OVEN
1.
2.
Place oven shelves in the chosen positions (refer to cooking charts).
Push in and turn the oven control knob fully anti-clockwise. Sparking will
continue until the burner has lit.
3.
4.
Turn the control knob clockwise to the required setting (refer to cooking chart).
There is a delay of about one minute whilst the safety device operates before the
burner comes on full.
To turn off, turn the control knob fully clockwise the the symbol O.
Never place dishes on the oven base over the burner.
An odour may be noticed when first using the oven – this should cease after a short
period of use.
RELIGHTING THE BURNER
In the event of the burner flames being accidentally extinguished, turn off the burner
control and do not attempt to re-ignite the burner for at least one minute.
10
OVEN
COLD START COOKING
Anything requiring long slow cooking such as casseroles and rich fruit cakes can be
put into a cold oven. Satisfactory results can also be obtained with creamed mixture,
rich pastries or yeast mixtures, but for perfection we recommend
preheating the oven for about 15 minutes.
ROASTING OF LARGE POULTRY
The maximum weight of poultry that can be accommodated is 22 lbs (10 kgs) of
suitable shape.
It is important to check that the bird DOES NOT overhang the burner at the back of the
oven.
STORAGE AND RE-HEATING OF FOOD
It is vitally important to strictly adhere to the basic principles of food handling and
hygiene to prevent the possibility of bacterial growth.
1. If food is to be frozen or not served immediately, cool it in a clean container as
quickly as possible.
2. Completely thaw frozen food in the refrigerator before re-heating.
3. Re-heat food thoroughly and quickly either on the hotplate or in a hot oven, Mk. 6,
and then serve immediately.
4. Only re-heat food once.
‘COOK CHILL’ DISHES
These should always be placed in a pre-heated oven ideally on the first or second shelf
position. Follow the packet instructions for cooking time.
ALUMINIUM FOIL
If using Aluminium Foil:
1. Remember that it is important to increase the cooking time by one third.
2. Never allow the foil to touch the sides of the oven.
3. Never cover the oven interior with foil.
4. Never cover the oven shelves with foil.
11
OVEN COOKING CHART
The following times and setting are for guidance only. You may wish to alter the setting to give a
result more to your satisfaction. When a different setting to that shown below is given in a recipe, the
recipe instructions should be followed. Allow 15 minutes preheat for best results. Always turn the
thermostat knob to Mark 9 before selecting the appropriate Gas Mark. Shelf position 1 is the highest.
Gas
Shelf
Food
Mark
Position
Approx. Cooking Time and Comments
25-60 mins. depending on recipe
Fish
Oily and white fish
Meat and Poultry
Beef
3 or 4
4
4 or 5
5
4
4
25-30 mins per 450g (1lb) + 25 mins. extra
Ham
40 mins per 450g (1lb) covered in foil plus
40 mins. extra
Lamb
5
4
4
30 mins per 450g (1lb) + 30 mins extra
40 mins per 450g (1lb) + 40 mins extra
25 mins per 450g (1lb) + 25 mins extra
25 mins per 450g (1lb) + 25 mins extra
15-20 mins per 450g (1lb) + 20 mins
2-6 hrs. depending on cut of meat
Pork
5
Chicken
5
5
4
Duckling & Goose
Turkey
4
4 or 5
3
4 or 5
3 or 4
Casseroles
Vegetables
Baked jacket potatoes
Puddings
1
2
4 or 5
3
3
4
1 / - 3 hrs. until soft, depending on size
3
1
4
2
Milk Puddings (500ml/1pt)
1 / - 2 / stand dish on baking tray and
started with warm milk
Baked Custard (500ml/1pt)
Baked Sponge Puddings
Baked Apples
3
4
3
4
3
3
45-60 mins. bain-marie
40 - 50 mins
30-45 mins depending on type and size
of apples
Meringue Topped Puddings
Apple Tart (1 x 205mm/8”)
Fruit Crumble
1
6
5
3 or 4
15 mins or until “tinged” with brown
45-60 mins
3
3
35 - 45 mins
12
OVEN COOKING CHART
Gas
Mark
Shelf
Positions
Food
Approx. Cooking Time and Comments
Cakes, Pastries & Biscuits
Small Cakes (16 per tray) 2 trays
1 tray
5
5
4
5
2
4
2
7
2
4
6
5
7
6
2 and 4
2
17 - 25 mins.
17 - 25 mins.
Victoria sandwich (2 x 180mm / 7”)
Swiss Roll (3 egg quantity)
Christmas cake (1 x 205mm / 8”)
Madeira cake (1 x 180mm / 7”)
Rich Fruit cake (1 x 180mm / 7”)
Scones - 16 per tray
Shortbread (1 x 180mm / 7”)
Biscuits
2 and 4
2
20 - 30 mins
20 - 25 mins.
3 or 4
3
3 - 6 hrs depending on recipe
1
1
4
2
1 / - 1 / hrs.
1
2
3
3 - 3 / hrs.
2 and 4
3
10 - 30 mins. depending on recipe
45 - 60 mins. depending on recipe
15 - 35 mins. depending on recipe.
15 - 60 mins. depending on recipe
20 - 40 mins. depending on recipe
10 - 30 mins. depending on recipe
25 - 35 mins.
2 and 4
2 and 4
2 and 4
2 and 4
2
Shortcrust Pastry
Rich Short Crust
Flaky/Puff Pastry
Choux Pastry
Yeast Mixtures
Bread - rolls
7
2 and 3
15 - 45 mins depending on recipe
Miscellaneous
Yorkshire Pudding:– large
individual
7
7
2
2
35 - 45 mins
20 - 30 mins
4 and
baseplate
2 – 5 hrs. starting on shelf 4 until “set” and then
on the baseplate until dried out, turn if necessary.
Slow Cook
Meringues
When baking with two trays or tins on two levels, the top tray is removed first and the
lower tray moved up to the top position for a few minutes longer.
Soft Margarine – Use the oven settings recommended by the margarine
manufacturer and not those indicated on the cooking chart.
13
OVEN
THE ‘SLOW COOK’ SETTING
This is used for slow cooking, keeping food warm and warming plates for short
periods.
USING THE ‘SLOW COOK’ SETTING FOR SLOW COOKING
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum of
6 hours. They will ‘hold’ at this setting for a further hour but marked deterioration
in appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at Mk 6 for 30 minutes before
turning to the ‘Slow Cook’ setting and never be cooked lower than the middle
shelf position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2kg) should not
be cooked using the ‘Slow Cook’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air
circulation.
5. Pork joints and poultry must be checked for an internal temperature of at
least 88°C using a meat thermometer.
6. This method is unsuitable for stuffed meat and poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be
cooked lower in the oven whilst other dishes requiring greater heat can be
cooked above them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in day
cooking sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten minutes after
soaking, before inclusion in any dish.
14
CLOCK & MINUTE MINDER
CLOCK OPERATION
To Set Time of Day
Step 1
Step 2
Check that the electricity
supply to the cooker is turned
on.
When switched on the
display will show 0.00
flashing intermittently.
❍ ❍ ❍
Step 3
Press the “
“ button and
then press either the “+” or
“-” buttons to set the correct
time of day.
Note: If the electricity supply
has been off, the “+” button
must be pressed once before
the “-” button, if it is required
to reduce the time of day.
❍ ❍ ❍
THE TIME OF DAY IS NOW SET.
15
CLOCK & MINUTE MINDER
MINUTE MINDER OPERATION
To Set the Minute Minder
Step 1
Press the “+” button until the
required time is set. A “Bell”
symbol will light up. During
setting the time adjusts in 10
second intervals up to a
maximum of 99mins 50secs.
❍ ❍ ❍
It can also be adjusted by pressing the “-”
button.
At the end of the set time, a bleeping
sound will be heard and the “Bell” will
disappear.
The bleeper can be cancelled by pressing
the “+” button.
❍ ❍ ❍
The minute minder can be cancelled before the bleeper sounds by pressing the “+”
and “-” buttons together until 0.00 appears in the display window.
BLEEPER SOUND
To adjust the pitch of the bleeper, press the “-” button while the bleeper is sounding.
For example:-
(a) Press the “+” button and set 10 seconds.
(b) When the bleeper sounds, press and release the “-” button, until preferred
pitch is set.
(c) Press and release the “+” button to cancel the bleeper.
NOTE: If the sound of the bleeper appears to be different, it is most likely that the
pitch of the bleeper has been inadvertently adjusted.
16
CARE AND CLEANING
Switch off the electricity supply and allow to cool before cleaning the cooker.
Clean the cooker regularly and wipe up spills soon after they occur to prevent
them from becoming burnt on. Never use biological washing powder, caustic
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or oven
chemical cleaners of any kind.
Before moving your cooker ensure that it is cool and note that it is heavy so you
may require assistance. To move the cooker forward, open the grill door and with
both hands positioned under the roof of the compartment, lift and pull forward.
Replace by pushing the cooker backwards. Check that the cooker is level. Take care to
ensure that any floor covering is not damaged.
OVEN HEAT CLEAN LININGS
The oven roof and side linings are coated with a special enamel which has a
continuous cleaning action. The higher the oven temperature the more effective the
action. In most cases this cleaning operation will proceed during normal cooking.
However, if roasting is done frequently, or high temperatures are not used regularly, it
may be necessary to run the oven empty at Mark 8 for about two hours.
It should not normally be necessary to clean the linings with water, but if desired, wipe
them over with a soapy cloth, followed by a wipe with a damp clean cloth.
REPLACEMENT OF OVEN LIGHT BULB
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC
SHOCK
Light bulbs are not covered by the manufacturer’s guarantee.
A new 15W, 300oC rated SES bulb can be obtained from your cooker supplier or any
major electrical retailer.
1. Remove the shelves from the oven.
2. Unscrew the lens using a thick cloth to protect your fingers in the unlikely
event of a lens fracture.
3. Unscrew bulb.
4. Fit new bulb and refit lens.
17
CARE AND CLEANING
COOKER FINISH
CLEANING METHOD
Cloth wrung out in warm soapy water. Stubborn
stains can be removed with a cream paste,
liquid cleaner or by rubbing with fine steel wool
soap pads.
Check that the cleaning agent is approved by the
Vitreous Enamel Association.
Vitreous Enamel
Hotplate, burner caps,
fascia, roasting dish, grill
pan, oven base and rear,
inside of grill compartment,
inside of doors.
Paint
Side trims, plinth, fascia
bottom trim, side panels.
Lid & rear end caps,
door handles
Wash with a cloth wrung out in warm
soapy water only. DO NOT USE ABRASIVES.
Similar to paint cleaning above. Use a nylon brush to
remove any cleaning materials, water or dirt from the
hotplate burner rings.
Aluminium
Hotplate burner bodies
Glass
Oven/grill door fronts,
Lid
As for enamel cleaning. Polish with a clean dry
cloth or kitchen roll.
Chromium Plating
Oven shelves, grill pan grid,
grill pan handle support
Wipe with a cloth wrung out in warm soapy water.
A fine steel wool soap pad e.g. Brillo, Ajax, or a
chrome or stainless steel cleaner may be used.
Wipe with a cloth wrung out in warm soapy water.
Stubborn stains can be removed with a cream
cleaner.
Plastic
Grill pan handle,
control knobs
Note: To ensure rapid lighting of the hotplate burners every time they are used, the
ignitors must be kept clean and dry. Remove any food spillage or cleaning materials
from the electrode using a small nylon brush such as a toothbrush.
18
SOMETHING WRONG
WITH YOUR COOKER
Before calling a Service Engineer, please check through the following lists.
THERE MAY BE NOTHING WRONG.
Problem
Check
Slight odour or small
amount of smoke when
grill / oven used first
time
This is normal and should cease after a short period.
Check that the gas mark and shelf positions are as recom-
mended in the Oven Cooking Charts. However, it may be
necessary to increase or decrease the recommended setting
slightly to suit your taste.
Oven cooks too fast or too
slow
Ignition does not work.
If all burners fail to ignite:
Check that sparks appear at the burners; a clicking noise
should be heard.
Oven burner
If not
Check that the electricity supply is turned on.
If only one burner fails to ignite:
Burner ports
Ignitor
Check that the burner is dry and that spillage of food or
cleaning fluid remains are not affecting the ignitor or
burner ports.
Grill burner
Clean away any debris with a dry nylon brush such as an
old toothbrush. If a wire wool pad has been used for
cleaning around the burner ensure the ignitor is free from
any stray strands. Any water on the burner should be dried
with a cloth or kitchen towel.
Burner ports
Ignitor
Hotplate burner.
On the hotplate make sure that all the burner parts are
correctly seated.
Burner ports
Ignitor
19
INSTALLATION INSTRUCTIONS
Prior to installation, ensure that the local distribution conditions (nature of the gas and
gas pressure) and the adjustment conditions are compatible. The adjustment condi-
tions for this appliance are stated on the data badge which is fitted on the back panel.
This appliance is not designed to be connected to a combustion products
evacuation device. It must be installed and connected in accordance with current
installation regulations. Particular attention should be given to the relevant require-
ments regarding ventilation.
MODEL NUMBERS 10510G, 10512G, 10515G and 10518G
2H
Category I (GB, IE)
These models are set to burn NATURAL GAS (G20) at 20 mbar ONLY and
cannot be used on any other gas.
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in
accordance with the current edition of the above regulations. It is in your interest and
that of safety to ensure compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice.
The cooker must also be installed in accordance with BS 6172.
Failure to install the cooker correctly could invalidate the warranty liability claims and
could lead to prosecution.
LOCATION
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in
a room containing a bath or shower. The cooker must not be installed in a bed-sitting
room of less than 20m3.
PROVISION FOR VENTILATION
The room containing the cooker should have an air supply in accordance with
BS 5440:Part 2.
The room must have an opening window or equivalent; some rooms may also require
a permanent vent. If the room has a volume between 5 and 10m3, it will require an air
vent of 50 cm2 effective area unless it has a door which opens directly to outside. If the
room has a volume of less than 5m3, it will require an air vent of 100 cm2 effective area.
If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be
consulted to determine air vent requirements.
20
INSTALLATION INSTRUCTIONS
TECHNICAL DATA
DIMENSIONS
Height
900mm
Width
500mm
Depth
600mm (excluding door handles)
GENERAL
Gas connection
1
1
2
2
Rp / ( / ” BSP female)
Pressure test point
Gas rate adjustment
Aeration adjustment
Electrical connection
Grill injector
None
None
Flexible cord fitted with a 3 pin 13 amp plug
230/240V a.c. 50Hz. 3A fuse.
NATURAL GAS
HEAT INPUT
BURNER
INJECTOR
128
HOTPLATE
3.0 kW
2.0 kW
1.0 kW
2.0 kW
3.8 kW
2.5 kW
Front left
HOTPLATE
102
Rear left
HOTPLATE
72
Rear right
HOTPLATE
102
Front right
GRILL
OVEN
150
115
21
INSTALLATION INSTRUCTIONS
SPACE FOR FIXING
The cooker can be close fitted below hotplate level. This requires a minimum
distance of 503mm between cupboard units of hotplate height.
When installing next to a tall cupboard, partition or wall, for a minimum distance of
400mm above hotplate level, allow a side clearance of at least 65mm.
The diagram below illustrates the minimum clearance between the cooker and adja-
cent walls, cupboards etc.
The wall behind the cooker, 150mm below the hotplate and 450mm above, and the
width of the cooker, must be a non-combustible material such as ceramic wall tiles.
If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a
clearance of at least 50mm to allow the main oven door to open fully for when remov-
ing oven shelves.
65 mm Min
503 mm Min
COOKER HOODS
If a cooker hood is to be installed, refer to the cooker hood manufacturers’ instructions
regarding fixing height.
22
INSTALLATION INSTRUCTIONS
UNPACKING THE COOKER
Unpack the components from inside the grill and oven: Check that the following parts
are present.
Grill pan and grid
Baking dish
Oven shelves (2)
Literature
Grill pan handle
Pan supports (2)
Enamelled discs (4)
Aluminium burner bodies (4)
LEVELLING
Four skid feet are fitted which can be adjusted up or down to level the cooker.
CAUTION: Some soft floor coverings may get damaged if the cooker is not moved
carefully.
STABILITY BRACKET
One of the holes in the rear of the cooker can be
used to engage a stability bracket. The bracket
must be fitted to the wall behind the cooker.
The diagram is a guide to the correct height at
which the bracket should be from the floor .
155mm
Floor to bracket.
CONNECTING TO GAS SUPPLY
The cooker is designed to match the depth of standard 600mm worktops. An adaptor
backplate should, therefore, be fitted within the shaded area shown to allow the
cooker to be pushed fully to the wall. If a forward facing backplate is used, it must be
chased into the wall.
250
Connection to the cooker should be made with an approved appliance flexible
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose
chosen should be such that when the cooker is in situ, the hose does not touch the
floor.
The temperature rise of areas at the rear of the cooker that are likely to come in
contact with the flexible hose do not exceed 70oC.
23
ELECTRICAL CONNECTION
WARNING – THIS APPLIANCE MUST BE EARTHED.
CONNECT TO A 230-240V A.C. SUPPLY ONLY.
Connection to the electricity supply should be made via a properly earthed, readily accessible
wall socket which is adjacent to but not directly above, and not more than 1.25m away from the
appliance and capable of electrical isolation.
The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back
panel above a height of 650mm from the floor.
Should this plug not fit the socket outlet in your home it should be cut off and replaced with a
suitable plug as outlined below.
NOTE: The removed plug cannot be used for any other appliance and should therefore be
properly disposed of and not left where children might find it and plug it into a supply
socket – with the obvious consequent danger.
IF THE FITTED PLUG IS REMOVED
The flexible mains lead must be correctly connected as below to a three pin plug of not less
than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which
is approved to B.S. 1362.
IMPORTANT: The wires in the mains lead fitted to
this appliance are coloured in
accordance with the following code:
Green &
Yellow to
Earth
Brown to
GREEN AND YELLOW – EARTH
Blue to
Neutral
Live
BLUE
– NEUTRAL
– LIVE
BROWN
3 Amp
Fuse
Cord Clamp
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:– The wire which is
coloured green and yellow must be connected to the terminal in the plug which is marked with
the letter E or by the earth symbol
or coloured green or green and yellow. The wire which is
coloured blue must be connected to the terminal which is marked with the N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all
strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead
clamp on the plug. As the appliance must be earthed, do not use 2-pin
sockets outlets, if you are in doubt, consult a qualified electrician.
Should the mains lead ever require replacement, it is essential that this operation be
carried out by a qualified electrician and should only be replaced with a flexible cord of the
same size i.e. 0.75mm2 cross sectional area and temperature rating of 850 C e.g. heat resisting
PVC.
IF A MOULDED PLUG IS FITTED
In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362
must be fitted.
NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the
fuse cover the plug must not be used until a replacement fuse cover has been obtained and
fitted. A new fuse cover can be obtained from your local Electricity Board. The colour of the
correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug.
Make sure that the cable does not become trapped when pushing the cooker into position.
24
INSTALLATION INSTRUCTIONS
INSTALLATION AND OPERATIONAL CHECKS
After installation, check for gas soundness. The supply pressure can be checked at the
grill injector. Access to the injector is by first removing the baffle at the front of the grill
fastened by two screws. Then remove the fastening screw on the right hand side of the
burner and slide the burner off the injector. Ensure that the grill burner is correctly
located under the fixing screw on reassembly.
Fit the hotplate burner bodies, enamelled discs and pan supports. Referring to the
instructions for use where necessary,
1. Check that the hotplate and grill burners ignite correctly and burn with a
steady flame. Check for a steady flame on the low setting.
2. Check that with the oven set to mark 9, the burner ignites at low rate, and
then increases to full rate within 60 seconds. Leave the oven full on with
the door closed for 10 minutes, and check that when the control is turned to
the ‘Slow Cook’ setting that the flame reduces. Check that the oven light operates.
3. Check the operation of the timer.
Instruct the user on the operation of the cooker.
25
DISPOSAL OF YOUR PRODUCT
To minimise the risk of injury to children please dispose of your product carefully and
safely. Remove all doors and lids (where fitted). Remove the mains cable (where
fitted) by cutting off flush with the appliance and always ensure that no plug is left in
a condition where it could be connected to the electricity supply.
To help the environment, Local Authority instructions should be followed for the
disposal of your product.
Key Contacts
Service
We have the largest appliance manufacturer’s service team in Europe,
specialists directly employed by us to ensure
your complete confidence.
trained
Repair Service
UK: 08709 066 066
Republic of Ireland: 1850 302 200
You will be asked for the following information:-
Name, address and postcode.
Telephone number
Model / Serial number of the appliance
Clear and concise details of the query or fault
Place and Date of purchase
(Please keep the receipt as evidence will be required when the engineer calls).
Extended Warranty
To join: UK 08709 088 088
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
Mail Order Hotline
UK: 08709 077 077
Republic of Ireland: (01) 842 6836
For further product information 01782 385516
All Cannon Services are offered as an extra benefit and do not affect your statutory rights.
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.
|