Capresso Coffeemaker 464 User Manual

CoffeeTEAM GS, #464  
10-Cup Digital Coffee Maker/  
Conical Burr Grinder  
Combination  
• Operating Instructions  
• Warranty  
• Product Registration  
 
SPECIAL CORD SET INSTRUCTIONS  
CAUTION:  
This appliance is for household use. Any servicing other than  
cleaning and user maintenance should be performed by an  
authorized service representative.  
This appliance has a polarized plug (one blade is wider than  
the other). As a safety feature,this plug will fit in a polarized  
outlet only one way. If the plug does not fit fully in the outlet,  
reverse the plug. If it still does not fit, contact a qualified  
electrician. Do not attempt to defeat this safety feature.  
• Do not immerse base in water or try to disassemble.  
To reduce the risk of fire or electric shock, do not remove the  
base. No user serviceable parts inside. Repair should be done  
by authorized service personnel only.  
A. A short power supply cord is provided to reduce the risk  
resulting from becoming entangled in or tripping over a long  
cord.  
• Check voltage to be sure that the voltage indicated on the  
name plate agrees with your voltage.  
B. Longer extension cords are available and may be used if care  
is exercised in their use.  
• Never use warm or hot water to fill the water container. Use  
cold water only!  
C. If an extension cord is used,  
• Keep your hands and the cord away from hot parts of the  
appliance during operation.  
1) the marked electrical rating of the extension cord should  
be at least as great as the electrical rating of the appliance,  
and  
• Never clean with scouring powders or hard implements.  
2) the longer cord shall be arranged so that it will not drape  
over the counter top or tabletop where it can be pulled  
on by children or tripped over.  
1. WELCOME AND THANK YOU  
Thank you for choosing the CAPRESSO CoffeeTEAM GS. Please  
read all of the instructions in this booklet before operating your new  
machine. Understanding and complying with these instructions is  
essential to ensure that the machine is utilized without risk and  
to ensure safety during operation and maintenance.  
3.  
 
2. HOW TO CONTACT CAPRESSO  
4.  
Fig. 1  
Should you require further information or if particular  
problems occur that are not covered in this manual, please  
• CALL our toll free HELP LINE: 1-800-767-3554  
Monday-Thursday 8AM to 9PM, Friday 8AM to 8PM and  
Saturday 9AM to 5PM Eastern Standard Time. Feel free to  
call at any time. If you are connected to our voicemail,  
PLEASE DO NOT HANG UP. Leave your name, telephone  
number and time to call back. Please leave the model number  
of your Capresso product, in this case it is #464.  
1.  
5.  
6.  
2.  
3.  
7.  
8.  
9.  
• FAX us at 1-201-767-9684  
• E-MAIL us at [email protected]  
10.  
11.  
• WRITE to JURA Inc., Customer Service,  
P.O. Box 775, Closter, NJ 07624  
3. CUSTOMER SERVICE  
If you require any assistance, please call our toll free number  
1-800-767-3554 or email us at [email protected] or  
fax us at 201-767-9684.  
12.  
1. GoldTone filter  
7. Water tank lid  
2. Filter insert with drip stop  
3. Filter holder  
8. Feeder channel (Fig. 6 & 7)  
9. Water tank  
4. Charcoal filter holder (Fig. 12)  
5. Bean container lid  
6. Bean container  
10. User panel (Fig. 2)  
11. Filter release button  
12. Scoop  
4.  
 
User Panel  
AM  
Display  
Grinder fineness setting  
Fig. 4  
Filter release  
button  
Fig. 2  
Fig. 3  
Drip stop  
in filter insert  
Charcoal  
filter  
Fig. 5  
Fig. 6  
Fig. 7  
Fig. 8  
5.  
 
4. COFFEE BEANS AND THE BUILT-IN BURR GRINDER  
Grinding the beans just before brewing will maximize the flavor  
and aroma of your coffee. Conical burr grinders are considered  
bean container. The coating might stick to the burrs and, over  
time, will reduce the performance of the grinding mechanism.  
• Do not add any liquid flavorings or syrups to the beans.  
the best way of grinding beans. The slower grinding speed of the • If you like flavored coffee we recommend buying liquid flavorings  
conical burrs creates less heat thus preserving more aroma of  
the ground coffee. Following the recommendations below will  
make your coffee taste better and your machine last longer.  
at your local coffee store. Add a few drops into the carafe  
before or after brewing.  
e. Stones And Beans  
a. Storing Coffee Beans in the Freezer?  
Every coffee specialty store will tell you that occasionally small  
stones can be found in between coffee beans. Very small stones  
will be processed through the burr grinder without any harm  
(the stone will end up in your filter - not in your brewed coffee).  
However, larger stones can block the burr grinder permanently.  
If this happens, the grinder will make a loud noise. Push the  
On/Off button to stop grinding and call our customer service toll  
free number: 1-800-767-3554. Here is how you can avoid stones  
entering the bean container:  
Coffee Stores do not store beans in the freezer or refrigerator!  
Coffee will act like baking soda, absorbing all odors and  
tastes surrounding it. Coffee beans will stay fresh for several  
weeks as long as you keep them in a dry, dark container. (It’s the  
ground coffee which will lose aroma rapidly!) If you must store  
coffee beans in the freezer, take them out the day before use.  
This way they will absorb less odors and have time to thaw.  
Important: If you fill beans from the freezer directly into the  
grinder, moisture will seep into the burrs and the feeder channel.  
The moisture makes the ground coffee stick in the feeder channel  
and will clog it up over time.  
• Shake your bean bag thoroughly so that a stone will fall to  
the bottom of the bag.  
• Before emptying the bottom half of the bag of beans into the  
bean container, check to see whether there are any particles  
that look like stones, and remove them.  
b. Finer or Coarser Grind?  
The five grind settings (Fig. 4) of your CoffeeTEAM are calibrated  
for grinding drip coffee. Choose the coarser settings for darker,  
oilier beans. Choose the finer settings for light or medium roasts.  
5. PLEASE, NEVER... (the following voids the warranty):  
• Never fill instant coffee into the bean container; it can damage  
the functioning of the grinder and the machine.  
• Never fill coated coffee beans into the bean container.  
• Never fill water or any other liquid into the bean container.  
• Never fill anything other than coffee beans into the bean  
container (no chocolate, no nuts, no spices).  
c. Dark Beans versus Light Beans  
Your CoffeeTEAM burr grinder is calibrated to work with all  
different kinds of roasts. Dark, oily beans will leave some oil  
residue in the feeder channel. Over time this can slow down the  
flow of ground coffee. For cleaning the feeder channel see page 12.  
• Never fill anything but fresh, cold clean water into the water  
container.  
• Never remove or attempt to disassemble the bean container.  
d. Flavored beans, liquid flavorings, syrups  
• Do not use sugar or powder coated beans in the grinder (e.g.  
cinnamon, chocolate, vanilla etc). Coated beans can pit the  
6.  
 
• Never grind into the GoldTone filter unless it is empty of  
previously used coffee grounds.  
• Never operate the machine when the feeder channel cover is  
removed.  
• 150 gram bean container holds enough beans for up to two  
pots of coffee.  
• Set to grind for 2, 4, 6, 8 or 10 cups (Indicator in LCD display).  
• Fine-tune for mild, regular or strong coffee (Indicator in LCD  
display).  
6. EQUIPMENT  
Turn the bean container from left to right to change the grind  
settings from finer to coarser in five steps.  
• Charcoal filter removes chlorine and other impurities in the  
water before brewing.  
The CoffeeTEAM GS comes with:  
• instruction book (includes warranty)  
• order form for parts and accessories  
• one measuring scoop*  
• one glass carafe (model #464)  
• one GoldTone filter  
• filter holder insert  
8. BEFORE INITIAL USE  
• Carefully unpack your machine and remove packing materials.  
• Wipe the machine with a damp cloth.  
• charcoal filter holder and one charcoal filter cartridge*  
If any of these parts are missing, please call toll-free:  
1-800-767-3554.  
* The scoop and the cartridge are located inside the carafe.  
Empty carafe before using.  
• Push the filter holder button (fig. ), remove the goldtone filter  
and the filter insert and clean.  
• Make sure the drip stop of the filter insert is working properly.  
• Open the water container lid and remove the charcoal holder.  
If you intend to use the charcoal filter insert, see chapter 9.6.  
• Remove the charcoal cartridge and measuring scoop from the  
carafe.  
7. FEATURES AND BENEFITS OF THE COFFEETEAM  
• After grinding, the CoffeeTEAM automatically starts the  
brewing process.  
• Drip-stop function lets you pull out carafe and serve a cup or  
two before brewing is finished.  
Please note:  
The filter holder, the basket, the glass carafe (Model #464) and  
carafe lid are dishwasher safe (upper rack, away from any  
heating element).  
• CoffeeTEAM GS, #464 (glass carafe): Warming plate keeps  
coffee hot for 2 hours, then the warming plate shuts off.  
• Easy to read LCD display with AM/PM clock and auto-on  
programming.  
Caution: Do not immerse the machine in water or any other liquid.  
• Machine can be used with or without grinder to accommodate  
pre-ground coffee.  
• Heavy duty, conical burr grinder delivers slow, precise and  
no-heat grinding to preserve natural coffee bean aroma.  
• Grinds directly into filter holder.  
7.  
 
Important:  
• Push and hold the PROG button until the display shows AUTO  
and a random number is blinking.  
• Keep the PROG button depressed.  
• CoffeeTEAM GS (glass carafe): when brewing, always have the  
lid in place.  
• Push and hold the H, then the M button to set Auto-On time.  
• Release the PROG button. The display reverts to the actual time.  
• Let some water brew through the machine without any coffee  
as follows.  
• Plug in machine and make sure the GoldTone filter and filter  
insert are in place.  
• Fill the water tank with approx. 20 oz. of water and place the  
carafe with lid in the machine.  
• Push the BREW button, then the ON/OFF button (Fig. 2).  
The machine starts processing the water into the carafe.  
• After all water has passed through, push the ON/OFF button  
again to turn off machine.  
c) To change the Auto-On Time  
• Push and hold the PROG button until the display shows AUTO.  
Keep the PROG button depressed.  
• Push and hold the H and then the M button to set a new  
Auto-On time.  
• Release the PROG button. The display reverts to the actual time.  
d) Checking the Auto-On Time  
• Push and hold the PROG button. The display shows the word  
“AUTO” and the Auto-On time.  
• Empty carafe  
9. PREPARING THE COFFEETEAM  
9.1 CLOCK AND GRINDER SETTINGS  
Plug in machine. The display shows “0:00” blinking and either  
the “BREW” or the “GRIND/BREW” light is illuminated (Fig. 2).  
Please note: You must set the actual time before you can operate  
the coffee maker.  
• Release the PROG button. The display reverts to the actual time.  
e) Activating the Auto-On Time  
• Push the PROG button briefly. The display shows “AUTO” and  
the green Auto-On light illuminates, indicating the Auto-On  
setting is active. The machine will show the actual time. At the  
pre-programmed time the machine starts grinding and brewing  
(or brewing only). For details see chapter 10.2 & 11.1.  
a) Setting the Actual Time  
• The display shows “0:00” blinking  
• Push and hold the H button until the actual hour is displayed.  
The display will also show AM or PM.  
• Push and hold the M button until the minutes are displayed.  
The time is now set.  
f) Grind Volume Setting: the “2-10” button  
Please note: the CoffeeTEAM lets you set two different grinder  
settings: one for immediate use and one for Auto-On use. For  
both uses the default setting is “10”.  
For immediate use: Push the “2-10” button repeatedly to select  
from 2, 4, 6, 8, 10.  
For Auto-On use: Push and hold the PROG button until the  
word “AUTO” is displayed. Keep the PROG button depressed  
and then push the “2-10” button to select from 2, 4, 6, 8, 10.  
Please note: You must change the clock when the time changes  
(Standard time/Daylight Savings time).  
b) Setting the Auto-On Time  
You can only set the Auto-On Time after the actual time is set.  
8.  
 
g) Strength Setting: the “AROMA” button.  
Please note: the CoffeeTEAM lets you set two different “Aroma”  
settings: one for immediate use and one for Auto-On use.  
9.4 SETTING THE GRINDER FINENESS / FILLING THE BEANS  
• Select the fineness setting (Fig. 4) by turning the bean container  
until the white triangle matches up with one of the five dots in  
front of the bean container. The largest dot to the right indicates  
the coarsest grind setting.  
• For first time use, use the coarsest setting – the largest dot.  
• For dark oily beans use the coarsest setting. For light, dry  
beans use the finer settings.  
The display shows the “middle” bean (default setting). You can  
select a lighter or darker bean by pushing the “AROMA” button.  
The lighter bean will reduce the grinding time by one second,  
the darker bean will increase the grinding time by one second.  
The result will be a somewhat milder or stronger coffee.  
For Auto-On use: Push and hold the PROG button until the  
word “AUTO” is displayed. Keep the PROG button depressed  
and then push the AROMA button to make your selection.  
Fill the bean container (Fig. 1.6) with beans. Make sure that the  
water container lid is closed to prevent beans from spilling into  
the water container.  
Caution: Check beans for foreign objects (page 6, chapter 4e).  
The bean container will hold approximately 150 grams of beans,  
good for two full pots of coffee in grinder setting 10.  
Note: Never fill the bean container with frozen or coated beans  
(chapters 4a and 4d, page 6).  
9.2 COFFEE STRENGTH RECOMMENDATION  
In setting “10” with “AROMA” set to the dark bean, the machine  
will grind for about 40 seconds (producing the maximum amount  
of coffee). In setting “2” and “AROMA” set to the light bean, the  
machine grinds for about 7 seconds.  
9.5 FILLING THE WATER CONTAINER  
Open the water container lid (Fig. 1.7) and fill the water container  
with the desired amount of fresh, cold water.  
Please note: Never fill water above the 10-cup marking. The  
water container has an overflow opening in the back.  
• For 10 cups of strong coffee we recommend the setting 10 and  
the middle bean.  
• If the coffee tastes too strong, change the grinder setting to  
the number 8 or lower.  
• If the coffee is not strong enough, set the aroma setting to the  
darker bean. If the coffee is still not strong enough, reduce the  
amount of water.  
9.6 CHARCOAL WATER FILTRATION  
CoffeeTEAM comes with one charcoal cartridge and a charcoal  
filter holder. You can brew coffee with or without the water  
filtration system.  
9.3 POWER INTERRUPTION  
Note: If you use distilled, spring or bottled water or if your water  
has little or no chlorine you may not find a difference in taste in  
your coffee when using the water filtration system. However,  
most tap water is treated with chlorine. The water filter cartridge  
removes up to 82% of the chlorine found in your tap water.  
• If the machine is unplugged or power is interrupted all settings  
described in chapters 9.1 and 9.2 must be reset.  
• If the machine was set to Auto-On and power was interrupted,  
the machine will not brew coffee at the programmed time.  
9.  
 
Initial Preparation:  
• Open the water container lid and remove the charcoal filter  
holder.  
• Remove the charcoal filter from poly bag.  
• Soak the filter in a glass with cold water for a few minutes.  
This will activate the filter.  
• Insert the cartridge into the charcoal filter holder (Fig. 12).  
• Place the charcoal filter holder back into the water tank.  
9.8 MODEL #464: USING THE GLASS CARAFE  
The CoffeeTEAM GS, model #464, comes with a glass carafe.  
Always make sure that the lid of the carafe is in place when  
brewing coffee. Without the lid, the drip stop cannot be activated.  
If you lose the lid, you cannot brew coffee. Use the enclosed  
mail order form or call 1-800-767-3554 to order a new lid. Do  
not place carafe in microwave, oven or stove.  
10. GRINDING AND BREWING COFFEE NOW  
• Coffee maker is plugged in and the time, auto-on time are set.  
• Beans are in the bean container.  
• Fill the water tank with the desired amount of water.  
• Make sure the filter insert and GoldTone filter are in place and  
the GoldTone filter is empty.  
When to replace the cartridge:  
• Replace the filter after 60 pots of coffee or 6 weeks after first  
use, whichever comes first. Unused cartridges can be stored  
indefinitely.  
• Replacement cartridges are available through your local  
Capresso dealer or by using the enclosed mail order form or  
• Make sure the Filter holder is closed.  
• Insert the carafe with lid into the machine.  
• Make sure the “GRIND/BREW“ button is illuminated.  
• Push the ON/OFF button (Fig. 2). The red ON/OFF light  
illuminates. The grinder will start grinding and the ground  
coffee will push into the GoldTone Filter. Through the window  
in the feeder channel cover, you can see the ground  
coffee move forward. Once grinding is finished, the brewing  
process starts.  
CAUTION: As long as the grinder is in operation, do not open  
the bean container lid and do not insert your finger or any other  
object into the grinder.  
9.7 GOLD TONE FILTER AND FILTER INSERT  
• Push the Filter Release button (Fig. 1.11). The filter holder swings  
open. The Goldtone filter and the filter insert can be removed.  
• Before grinding/brewing coffee always make sure that the  
GoldTone filter is empty and placed into the filter insert.  
CAUTION/ DANGER!  
• Never use the coffee maker without the filter insert and  
GoldTone filter. Extremely hot water can overflow onto the  
warming plate and counter. If this occurs, turn the machine off  
and wait until the brewing stops.  
• Then push the Filter Release button, add the filter insert and  
the GoldTone filter and close the filter holder. Place the carafe  
underneath and continue brewing until the water tank is empty.  
10.  
 
CoffeeTEAM GS (glass carafe):  
• Make sure the “GRIND/BREW” light is illuminated.  
• Push the PROG button briefly. The green light turns on and the  
display shows “AUTO”. At the preprogrammed time, the green  
light will turn off, the red ON/OFF light will illuminate and the  
grinding and brewing will start.  
• After brewing is finished remove the carafe from the platform.  
Slowly pour coffee. Return the carafe to the heating platform.  
• The CoffeeTEAM GS will keep the coffee hot for two hours  
after brewing. Then the ON/OFF light will turn off, indicating  
that the heating element is turned off.  
Recommendation: If you want your coffee ready by 7:30, set  
the auto-on time to 7:15.  
To keep coffee hot longer:  
First push the BREW button, then push the ON/OFF button.  
This prevents the machine from grinding again.  
11. BREWING COFFEE WITHOUT THE GRINDER  
You can use your CoffeeTEAM like a regular drip coffee maker  
with pre-ground coffee (without using the grinder).  
• Open the water container lid (Fig.1.7) and fill the desired  
amount of cold water into the water container.  
• Push the Filter Release button to open and fill ground coffee  
into the GoldTone filter. Close the Filter Holder.  
10.1 DRIP STOP / STOP AND SERVE  
• While the coffee is brewing you can remove the carafe to pour  
a cup or two. The drip stop will close automatically.  
To avoid any overflow, replace the carafe within 20 seconds.  
CAUTION: The drip stop might not close completely allowing  
coffee to drip onto the platform. In this case immediately place  
carafe back into the machine and let all the coffee flow into the  
carafe.  
• After brewing is finished, check the GoldTone filter for any  
clogging and rinse the filter insert to remove any coffee  
particles from the drip stop (Fig. 5).  
• Insert the carafe with lid into the machine.  
• Push the “BREW” button. The red “BREW” light illuminates.  
• Push the ON/OFF button. The red ON/OFF light illuminates and  
the brewing process starts immediately.  
11.1 BREWING PREGROUND COFFEE LATER ("AUTO")  
• Coffee maker is plugged in and the time, auto-on time are set.  
• Fill the water tank with the desired amount of water.  
• Push the Filter Release button to open and fill ground coffee  
into the GoldTone filter. Close the Filter Holder.  
10.2 GRINDING AND BREWING LATER ("AUTO")  
• Coffee maker is plugged in and the time and auto-on time are set.  
• Beans are in the bean container.  
• Fill the water tank with the desired amount of water.  
• Make sure the Filter Insert and GoldTone filter are in place and  
the GoldTone filter is empty.  
• Insert the carafe with lid into the machine.  
• Push the “BREW” button. The red “BREW” light illuminates.  
• Push the PROG button briefly. The green light turns on and  
the display shows “AUTO”. At the preprogrammed time, the  
green light will turn off, the red ON/OFF light will illuminate and  
the brewing will start.  
• Make sure the Filter holder is closed.  
• Insert the carafe with lid, into the machine.  
11.  
 
12. CLEANING  
recommend to descale at least twice a year. If you use hard  
water, it might be necessary to descale more often.  
Important:  
• Before decalcifying, remove the Goldtone Filter and Charcoal  
Filter.  
CAUTION: Make sure machine is turned off and cooled down.  
Never use scouring agents. Never immerse the machine in any  
liquid. Never clean machine under running water. Dishwasher  
safe (upper rack): GoldTone Filter and Filter Insert.  
Special Cleaning Tips:  
12a. GoldTone Filter: Clean after brewing. Do not let used  
coffee sit for hours in the filter. Coffee oils will clog the mesh,  
causing the coffee to overflow the next time you brew coffee.  
12b. Filter Insert /Drip Stop: Clean the Filter Insert and the drip  
stop under running water. Test that the drip stop closes  
completely under running water (Fig 5).  
12c. Bean Container: When the bean container is empty, use a  
dry cloth to wipe off any oil deposits. Never pour any liquid into  
the bean container. Never try to disassemble the bean container.  
13a. Decalcifying with Capresso Cleaning Solution  
Capresso recommends Capresso Cleaning Solution for drip  
1. Remove GoldTone Filter and Charcoal Filter.  
2. Dissolve 1 oz. (28 g) of Capresso Cleaning Solution with 32  
oz. (1 L) of water and pour mixture into water tank.  
3. Important: Make sure the Filter Insert is in place and the  
carafe is empty.  
4. Place the carafe with the lid closed into the machine.  
12d. The Feeder Channel: Periodically check the feeder channel 5. The BREW light is illuminated. Push the ON/OFF button.  
for oil and coffee build-up. As long as you can see coffee flowing 6. When the solution has run through, remove the carafe, empty  
freely through the feeder channel window there is no need to  
open the cover. The feeder channel should be cleaned in any of  
the following situations:  
• moisture or heavy oil build-up has caused the ground coffee  
to block the feeder channel, or  
and rinse thoroughly.  
Important: let the machine cool down for 5 minutes.  
7. Fill 20 oz. of fresh cold water into the water tank and brew  
through the machine.  
• you do not plan on using the grinder for more than a week.  
For cleaning, please follow this sequence:  
• Make sure the GoldTone filter is inserted in the Filter Insert.  
• With a pointed tip push the small pin in the window down and  
slide the plastic cover forward (fig. 6 & 7).  
• Wipe the inside clean with a dry cloth.  
• Replace the feeder channel cover.  
13b. Using other Decalcifying Agents  
• All decalcifying agents are acidic and must be handled  
carefully. Check the information on the packaging before using.  
Only use decalcifying agents suitable for drip coffee makers  
and follow the instructions which come with the agent.  
When the solution has run through, remove the carafe, empty  
and rinse thoroughly.  
Important: let the machine cool down for 5 minutes.  
• Fill 20 oz. of fresh cold water into the water tank and brew  
through the machine.  
13. Decalcifying  
When the brewing process slows down, it is time to decalcify  
your CoffeeTEAM. If you use your CoffeeTEAM daily we  
12.  
 
14. Frequently Asked Technical Questions  
15. Frequently Asked Coffee Questions  
Q1. There is no coffee coming out of the grinder. It seems as  
though the coffee is completely clogged inside the grinder.  
What do I do?  
Q1. How much coffee should I use?  
A. The grinder grinds approximately between 7 seconds (setting  
“2, mild”) and 40 seconds (setting “10, strong”).  
See chapter 9.2.  
A. Please follow the steps outlined in chapter 12d, page 12.  
Q2. Can the grinder run without beans in the bean container?  
A. Yes.  
Q2. I want a full pot of coffee at 8:00 AM. What time should I  
program the grinder to start?  
A. Set the timer 15 minutes earlier (in this case at 7:45 AM).  
Q3. Can I have different grind amount settings for the current  
and the programmed mode?  
Q3. The grinder makes a loud noise? No coffee is processed.  
A. Yes! See chapter 9.1, f.  
A. A stone blocks the grinder. Please call 1-800-767-3554.  
Q4. How long does the machine keep the grinding and brewing  
settings?  
A. As long as the machine is plugged in. If the machine loses  
power you have to reset the time and personal settings (see  
chapter 9).  
Q5. How do I know if the display shows the current or the  
programmed setting?  
A. The display always shows the current setting. To view the  
programmed setting push and hold the PROG button. The  
display will show “AUTO” and all settings for the Auto-On  
function.  
Q6. Beans spilled into the water container. What do I do?  
A. Unplug the machine, remove the carafe, empty the bean  
container (as well as you can), remove the filter holder insert  
and GoldTone filter, open the water container lid and turn the  
machine upside down over a sink. After replacing all parts,  
reset the time and program the machine again, see chapter 9.  
13.  
 
16. Limited One Year Warranty  
This warranty covers your CAPRESSO CoffeeTEAM model #464.  
The model number can be found on the bottom of the machine.  
This warranty is in effect for one year from the date of the first  
consumer purchase. This warranty covers all defects in materials  
or workmanship (parts and labor).  
with the sale of the machine. JURA expressly disclaims liability  
for incidental and consequential damages caused by the machine.  
The term “incidental damages” refers to the loss of the original  
purchasers time, loss of the use of the machine or other costs  
relating to the care and custody of the machine. The term  
“consequential damages” refers to the cost of repairing or replacing  
other property which is damaged when this machine does not  
work properly. The remedies provided under this warranty are  
exclusive and in lieu of all others. This warranty gives you specific  
legal rights, and you may also have other rights which vary from  
state to state.  
Transport: When sending the machine, use the original packing  
materials, the inner and outer cartons or use approximately 2” of  
bubble wrap and secure the machine properly. Any damage in  
transit is NOT covered by this warranty.  
This warranty does not cover:  
• Any machine not purchased from an Authorized Capresso  
Dealer.  
• Commercial use of machine.  
• Damage caused by accident, abuse, negligence, misuse,  
improper operation or failure to follow instructions contained  
in this manual.  
• Any service or alteration performed by an unauthorized  
person, company or association.  
Customer Service  
1-800-767-3554  
Mon-Thu 8AM – 9PM • Fri 8AM – 8PM • Sat 9AM – 5PM  
Eastern Time Zone  
• Damage caused by neglecting and omitting maintenance,  
cleaning and decalcifying.  
• Carafes (Glass or Thermal).  
• Charcoal Filters.  
JURA Inc.  
Other limitations and exclusions: Any implied warranties including  
fitness for use and merchantability are limited in duration to the  
period of the express warranty set forth above and no person is  
authorized to assume for JURA any other liability in connection  
81 Ruckman Road, Closter, NJ 07624  
201-767-3999 • Fax: 201-767-9684  
14.  
 

Bessey Drill PS55 User Manual
Billy Goat Work Light F1301H User Manual
Bowens Battery Charger EXPLORER 1500 User Manual
Briggs Stratton Portable Generator 01971 User Manual
Brother Cell Phone BCL D70 User Manual
Campbell Hausfeld Network Card SDM CAN User Manual
Cavalry Storage Washer Dryer CADA C32A User Manual
Century Welder IM10008 User Manual
Chicago Electric Vacuum Cleaner 97677 User Manual
Chief Manufacturing Stereo System PAS 100 User Manual