Casio Clock ID 25B User Manual

MA0405-EA  
Operation Guide ID-25B  
ILLUSTRATION  
SET  
RESET  
WAVE  
SET  
RESET  
WAVE  
A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the  
clock.  
°C  
°F  
MSF DCF  
Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the  
illustration.  
°C °F  
MSF DCF  
Normal Display  
DATE (month – date)  
Day of the week  
Antenna Icon  
Wave OK indicator  
Receive indicator  
Transmitter Indicator  
(DCF or MSF)  
PM indicator  
Current time  
(Hour, minutes, seconds)  
DST indicator  
1cm  
Current Temperature  
Current Humidity  
1
 
Operation Guide ID-25B  
Setting the Time and Date Manually  
THERMOMETER FUNCTIONS  
When using the clock in an area that is outside of the range of the transmitter or in an area where signal  
reception is impossible for some reason, you need to manually adjust the time setting as required.  
1. Press the SET button (2) to cycle through the setting screens as shown below.  
A built-in sensor measures temperature and shows the measured value on the display. The readout from the  
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).  
The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above  
70°C (158°F).  
Though temperature readings are displayed up to 0°C (32°F) and greater than 40.1°C (104°F), note that such  
readings are actually outside the guaranteed temperature range of this clock.  
Normal Timekeeping Screen  
Switching between Celsius and Fahrenheit  
Slide the °C / °F switch (6) to specify Celsius (°C) or Fahrenheit (°F) as the temperature unit.  
HYGROMETER FUNCTION  
A built-in sensor measures humidity and shows the measured value on the display.  
The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 95%.  
Year Setting Screen  
12-hour/24-hour Timekeeping Screen  
BATTERY REPLACEMENT  
Replace batteries whenever the display of the clock becomes dim and difficult to read.  
1. Pressing down lightly on the battery compartment cover, slide it downwards and remove it.  
2. Remove all of the old batteries.  
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct  
directions. If you load batteries incorrectly, they can burst and damage the clock.  
4. Replace the battery compartment cover.  
5. Press the RESET button (3). Be sure to press the RESET button (3) after replacing batteries.  
Battery precautions  
Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician  
immediately.  
Month and Day Setting Screen  
Time Setting Screen  
Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.  
Never mix old and new batteries, or batteries of different brands.  
Never charge the batteries that come with the clock.  
Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto  
your skin.  
Replace the batteries at least once a year, even if the current batteries are working properly.  
The batteries that come with the clock lose some of their power during transport and storage.  
2. While the screen you want is on the display, use the Time Set buttons (1) to change the digits that are  
flashing.  
Press + to increase the  
flashing digits.  
Press to decrease the  
flashing digits.  
Holding down + or changes the flashing digits at high speed.  
You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with  
the date setting.  
Pressing + or while the Time Setting Screen is on the display causes the seconds count to be reset to 00.  
Each press of + or while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour  
and 24-hour timekeeping.  
3. After making the settings you want, use the SET button (2) to display the Normal Timekeeping Screen.  
The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for  
about three minutes without performing any operation.  
3
 

Blackberry Water System 600 User Manual
Black Decker Hot Beverage Maker JKC550 User Manual
Bosch Appliances Security Camera NDN 265 PIO User Manual
Bosch Appliances Water Heater GWH 635 ES User Manual
Bosch Power Tools Router RA1181 User Manual
Brother Fax Machine FAX 236S User Manual
Brother Sewing Machine Innov is I User Manual
Canon Camcorder 1Ds User Manual
Chicago Electric Portable Generator 39461 User Manual
Chief Manufacturing Stud Sensor CTA 2536 User Manual