Casio Digital Camera YC 400 User Manual

English  
Multifunctional Camera System YC-400  
Projecting a Document Image  
Business Document Startup Mode Quick Guide  
Using the Operation Bar  
The PJ Camera Software’s Business Document startup mode is for recording and projecting images of paper  
documents and three-dimensional objects. This Quick Guide provides basic information and procedures for  
projecting in the Business Document Startup Mode.  
After completing the procedure under “To set up for projection” on the other side of this sheet, move  
the mouse pointer (  
) to the top of the screen on your computer display. This will cause the PJ  
Camera Software operation bar to appear.  
You can control the PJ Camera Software using the buttons and menus of the operation bar.  
I To set up for projection  
Install the bundled software (PJ Camera Software) on the computer you plan to use.  
1
Place the CASIO CD-ROM that comes bundled with the  
YC-400 package into the computer’s CD-ROM drive.  
DocumPrent CZamooemraZInoomSOcurt  
esentation  
Rotate SLheoftw DTocumeSnhtuMtteornitor  
r
apezoid Corr  
oll  
Tip  
You can also perform operation bar button  
operations from you computer keyboard, if you  
• This should cause the “CASIO Multi PJ Camera” screen to appear on  
your computer screen automatically.  
e
ction  
want. Sections marked  
contain  
information about keyboard operations.  
2
Click the tab for your language.  
I To project a document image  
Place the document you want to project onto the PJ Camera Stand’s document stage.  
3
4
5
Click the [Install] button for “PJ Camera Software” (top option).  
Follow the instructions that appear on your screen to install the software.  
After installation is complete, restart the computer.  
After your computer restarts, this icon (PJ Camera Software icon) will be  
displayed in your computer’s task tray in the lower right corner of the screen.  
×
×
• Configure your computer monitor’s resolution setting for XGA (1024 768) or SVGA (800 600). Using any  
other resolution setting will cause an error message to appear when you try to start up PJ Camera Software.  
The image that appears on your  
computer screen is called the monitor  
image.  
Set up the PJ Camera Stand.  
1
Unfold the PJ Camera Stand as shown below.  
Unfold these parts until  
you hear them click into  
place.  
Display the operation bar, and then click  
.
• This will project an image of the document.  
Instead of clicking the button above, you  
could press the [Enter] key on your computer  
keyboard.  
Tip  
When Trapezoid Correction is turned on, PJ Camera  
Software will correct the orientation of the projected  
image, up to a point, so the projected image appears  
straight, even if the document on the document stage is  
not straight. To turn on Trapezoid Correction, click the  
(Trapezoid Correction) button on the operation bar so it is  
The projected image, which is the image  
data recorded by the PJ Camera, is the  
document camera image.  
2
Attach the PJ  
Camera to the  
camera stand.  
Load the battery into the PJ Camera and then  
attach the camera bracket to the bottom of the PJ  
Camera.  
Press the PJ Camera against the  
camera bracket until it clicks securely  
into place.  
depressed (  
).  
To project the image of another document, replace the document on the document  
stage and then click  
.
Use a coin or some similar  
object to securely tighten this  
screw.  
After projecting the images of two or more documents, you can use the left or up arrow key to scroll to  
a previous document, and the right or down key to scroll forward through projected images.  
Connect the power cord and cables as shown below.  
I To zoom in on the projected document image  
Computer  
Projector  
While the image of a document is being projected, display the operation bar and then  
click  
.
USB cable  
• This changes the mouse pointer to  
.
Move the  
pointer to the part of the image that you want as the center of the  
RGB cable  
zoomed image, and then click.  
Important!  
Be sure to connect the bundled AC adaptor to the PJ Camera Stand.  
Operating the PJ Camera on battery power without connecting the AC adaptor to the PJ Camera Stand can run  
down battery and so projection becomes impossible.  
Note that the YC-400 does not come with an RGB cable. To connect a projector to your computer, use the RGB  
cable that comes bundled with the projector or purchase a commercially available cable.  
For full details about connections, see the documentation that comes with your computer and projector.  
• This will enlarge the projected image. You can perform this operation up to nine times.  
Turn on power.  
1
You can also zoom in on the projected image by holding down the computer’s [Ctrl] key and pressing [Ȇ].  
On the PJ Camera Stand, press the [  
] (power) button.  
• If you are starting up the system for the first time, a “Found New Hardware Wizard” dialog box will appear (in  
the case of Windows XP). Select the “Install the software automatically (Recommended)” check box, and then  
click [Next]. If the “CASIO MULTI PJ CAMERA has not passed Windows logo testing” dialog box appears,  
click [Continue Anyway]. If the “Digital Signature Not Found” dialog box appears, click [Yes].  
I To zoom out on the projected document image  
On the operation bar, click  
and then click the screen.  
You can also zoom out on the projected image by holding down the computer’s [Ctrl] key and pressing [ȇ].  
I To scroll a zoomed document image  
On the operation bar, click  
and then drag the screen.  
Important!  
The camera uses this cross mark for auto adjustments. Make sure  
there is nothing on the document stage at this time.  
You can also scroll the projected image pressing one of the arrow keys on the computer keyboard.  
I To return a zoomed image to its normal size  
• Turning on power will cause the PJ Camera Software to start  
automatically and display the dialog box shown nearby.  
Press the [Delete] key on the computer keyboard ([Del] key on some computers).  
Rotating the Projected Image  
Check to make sure that “Business Document”  
is selected as the startup mode.  
G To rotate the projected image 90 degrees right  
On the operation bar, click  
.
2
Leaving “Business Document” selected as the startup mode, click the [OK] button.  
• This will close the dialog box, and cause the PJ Camera to start auto adjustment.  
You can also rotate the projected image right by holding down the  
computer’s [Ctrl] key and pressing [Ǟ].  
G To rotate the projected image 90 degrees left  
On the operation bar, click  
.
You can also rotate the projected image left by holding down the  
computer’s [Ctrl] key and pressing [ǟ].  
I To quit PJ Camera Software  
Document projection setup is complete  
when your computer screen appears as  
shown above.  
On the operation bar, click  
.
 

Black Decker Coffeemaker DCM310 User Manual
Black Decker Vacuum Cleaner V1200 User Manual
Blue Rhino Charcoal Grill 251675 User Manual
Bolens Blower 241 692 000 User Manual
Bolens Lawn Mower 116 428N022 User Manual
Bosch Appliances Blender MCM 5000m User Manual
Brinkmann Gas Grill 4685 User Manual
Chauvet Oven D Fi 24 Rx User Manual
Christie Digital Systems Projector 38 VIV208 03 User Manual
Cisco Systems IP Phone OL 8148 01 User Manual