Chamberlain Universal Remote 84LM User Manual

Model 84LM 4-Button Remote Control  
OWNER’S MANUAL  
The push buttons on the 4-Button remote controls can activate garage  
door openers, entry ways and/or light controls. (Instructions for  
programming light products are included with those accessories.)  
WARNING  
To prevent possible SERIOUS INJURY or DEATH from a moving gate or  
garage door:  
Code switch remote controls are used when several persons are  
operating the same device. Code switches must be set to  
matching positions in all remote controls used to operate the  
same receiver. Follow the instructions for Figures 1 and 2. Use the  
“ribbed” push button exclusively for code switch application.  
• ALWAYS keep remote controls out of reach of children. NEVER permit  
children to operate, or play with remote control transmitters.  
• Activate gate or door ONLY when it can be seen clearly, is properly  
adjusted, and there are no obstructions to door travel.  
• ALWAYS keep gate or garage door in sight until completely closed. NEVER  
permit anyone to cross path of moving gate or door.  
Green  
Test Light  
Ribbed Push Button  
(Recommended for code  
switch application)  
Battery  
Figure 1  
Compartment  
Cover  
To Erase All Codes From Motor Unit Memory  
To deactivate any unwanted remote, first erase all codes:  
Press and hold the “learn” button on motor unit until the  
learn indicator light goes out (approximately 6 seconds).  
All previous codes are now erased. Reprogram each  
For use with  
Connector  
green “learn”  
button ONLY  
Battery  
KG  
KG  
remote or keyless entry you wish to use.  
To Attach the Visor Clip  
1. Remove the visor clip from the clip holder.  
Program the Ribbed push button (Code switch  
application)  
1. Remove the battery compartment cover as shown in Figure 1.  
2. Remove the case screw on the housing bottom.  
2. Remove the case screw. Insert tab on clip holder through circular  
label and into case, Figure 3. Slide clip holder forward.  
3. Replace the case screw (do not overtighten). Slide visor clip onto  
3. Hold the remote control as indicated and pull to separate the  
housing. Set aside the case top (with push buttons).  
clip holder.  
Visor Clip  
Clip Holder  
4. Place remote circuit boards side by side. Make sure you set code  
switches 1 through 9 in all remotes to matching positions (Figure 2).  
Use a pen or a screwdriver to move the switches to (+), (-) or (0).  
Figure 3  
Case  
Screw  
Case  
Screw  
Tab  
5. Reassemble case top and bottom by snapping them together.  
6. Replace the case screw and battery compartment cover.  
Slide  
Bottom of  
Clip Holder  
Remote  
Case  
Figure 2  
The Remote Control Battery  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
+
0
+
0
WARNING  
Match Code Switches (1-9)  
To prevent possible SERIOUS INJURY or DEATH:  
Program Receiver to Match Remote Control Code  
• NEVER allow small children near batteries.  
• If battery is swallowed, immediately notify doctor.  
1
2
3
The 9V battery should produce power for at least one year.  
If the green test light is dim or does not come on, replace  
the battery.  
9
1
9
1
7
3
7
3
5
5
To change the battery, remove the battery compartment  
cover, unsnap the connector and remove the old  
battery. Insert a replacement battery. Snap the  
connector onto the new battery and replace  
compartment cover.  
1
2
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of  
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing  
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.  
1
2
3
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the  
following two conditions: (1) this device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired operation.  
1. Press and release the “learn” button on the  
motor unit. The learn indicator light will glow  
steadily for 30 seconds.  
KG  
KG  
2. Within 30 seconds, press and hold the button  
on the hand-held remote.  
Replacement Parts  
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29C128  
Visor Clip Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31C412-1  
9V Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A16  
3. Release the button when the motor unit light  
blinks. It has learned the code. If light bulbs  
are not installed, two clicks will be heard.  
FOR SERVICE, DIAL OUR TOLL-FREE NUMBER: 1-800-528-2817  
IN CANADA, DIAL: 1-800-654-4736  
©2006, The Chamberlain Group, Inc.  
All Rights Reserved  
114A1887D  
 

Belkin Network Card F5U104 User Manual
BenQ Cell Phone S670C User Manual
Black Decker Saw CS2000 User Manual
Boston Acoustics Stereo Amplifier GT 2125 User Manual
Brunton Camping Equipment MM08 User Manual
Cal Flame Burner LTR20091082 User Manual
Campbell Hausfeld Nail Gun IN715703AV User Manual
Campbell Hausfeld Speaker System PA207802 User Manual
Canon All in One Printer 2520I User Manual
Century Carpet Cleaner CEXT7 User Manual