Chauvet Work Light TFX FS360 User Manual

READ FIRST!  
TFX-FS360  
Followspot400G  
To start using as a Followspot,  
press the FUNCTION button until  
the Manual LED turns on.  
Ask your dealer about  
the specially designed  
tripod stand with  
casters for the TFX-  
FS360.  
Model Number  
CH-W28  
USER MANUAL  
5200 NW 108th Ave Sunrise, FL 33351  
(800) 762-1084 (954) 929-1115  
FAX (954) 929-5560  
2010-07-20/14:53  
 
BEFORE YOU BEGIN  
What is included  
1x TFX-FS360  
1x Single gobo-slot with 4 free gobos  
1x Power cord with plug  
1x ENX lamp (360 W, 82 V)  
1x User Manual  
1x Warranty Card  
Unpacking Instructions  
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that  
all parts are present, and have been received in good condition. Notify the shipper immediately and  
retain packing material for inspection if any parts appear damaged from shipping or the carton itself  
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture  
must be returned to the factory, it is important that the fixture be returned in the original factory box  
and packing.  
AC Power  
To determine the power requirements for a particular fixture, see the label affixed to the back plate of  
the fixture or refer to the fixture’s specification. A fixture’s listed current rating is its average current  
draw under normal conditions. All fixtures must be powered directly off a switched circuit and cannot  
be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is  
used solely for a 0% to 100% switch. Before applying power to a fixture,  
AC Voltage Switch  
check that the source voltage matches the fixture’s requirement. Check the  
fixture or device carefully to make sure that if a voltage selection switch  
exists that it is set to the correct line voltage you will use.  
Warning!  
Verify that the power select switch on your unit matches the line  
voltage applied. All fixtures must be connected to circuits with a  
suitable Ground.  
Safety Instructions  
Please read these instructions carefully, which includes important  
information about the installation, usage and maintenance?  
Please keep this User Guide for future consultation. If you  
sell the unit to another user, be sure that they also receive  
this instruction booklet.  
Secure fixture to fastening device using a safety chain.  
Never carry the fixture solely by its head. Use its carrying  
handles.  
Maximum ambient temperature is Ta: 40°. Do not operate  
fixture at temperatures higher than this.  
In the event of serious operating problem, stop using the  
unit immediately. Never try to repair the unit by yourself.  
Repairs carried out by unskilled people can lead to  
damage or malfunction. Please contact the nearest  
authorized technical assistance center. Always use the  
same type spare parts.  
Don’t connect the device to a dimmer pack.  
Make sure power cord is never crimped or damaged.  
Never disconnect power cord by pulling or tugging on the  
cord.  
Always make sure that you are connecting to the proper  
voltage and that the line voltage you are connecting to is  
not higher than that stated on decal or rear panel of the  
fixture.  
This product is intended for indoor use only!  
To prevent risk of fire or shock, do not expose fixture to  
rain or moisture. Make sure there are no flammable  
materials close to the unit while operating.  
The unit must be installed in a location with adequate  
ventilation, at least 50 cm from adjacent surfaces. Be sure  
that no ventilation slots are blocked.  
Always disconnect from power source before servicing or  
replacing lamp or fuse and be sure to replace with same  
lamp source.  
Avoid direct eye exposure to lamp while it is on.  
Caution!  
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs  
yourself. In the unlikely event your unit may require service, please contact CHAUVET®.  
TFX-FS360 User Manual  
3
2010-07-20/14:53  
 
         
INTRODUCTION  
Features  
2-channel DMX-512 followspot  
7 dichroic colors + white: (red, blue, green, yellow, orange, magenta, UV purple)  
Variable electronic dimmer (0-100%)  
Variable mechanical iris  
Variable mechanical focus  
Additional Features  
Followspot stand (CH-W28)  
Options  
Single gobo slot with 4 free gobos  
DMX Channel Summary  
CHANNEL  
FUNCTION  
Color  
1
2
Dimmer  
Product Overview  
Lamp access  
Control panel  
Iris  
Gobo-holder  
Located and inserted on  
the bottom side of the  
followspot.  
Focus  
Yoke  
Gobos included  
Control panel  
DMX  
Input/Output  
Optional  
CH-W28 Tripod  
w/casters  
Focus handles  
TFX-FS360 User Manual  
4
2010-07-20/14:53  
 
           
SETUP  
Lamp  
You will need to install a lamp prior to the initial operation of the fixture. An ENX, 360 W halogen lamp  
is included.  
Warning!  
When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool  
down! Always disconnect from main power prior to lamp replacement.  
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp  
with alcohol and wipe it with a lint free cloth before installation.  
LAMP INSTALLATION  
Lamp Installation  
1) Remove screw located on the top and to the rear of  
Remove screw  
the followspot as pictured on the right.  
2) Open lamp cover until lamp compartment is exposed.  
3) If replacing the lamp, remove old lamp first.  
4) Reach in and slide the lamp out of the retaining cage.  
5) Detach the lamp from the lamp socket and replace.  
6) Replace lamp cover, align the screw hole and fasten  
the screw.  
7) No lamp alignment is necessary for this fixture since  
the lamp is already optimized inside the reflector.  
Lamp exposed  
Power  
Warning!  
Verify that the power on your unit matches the line voltage applied. All fixtures must be  
connected to circuits with a suitable Ground.  
To determine the power requirements for a particular fixture, see the label affixed to the back plate of  
the fixture or refer to the fixture’s specifications chart.  
A fixture’s listed current rating is its average current draw under normal conditions.  
All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable  
resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%  
switch.  
Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.  
All fixtures must be connected to circuits with a suitable Ground.  
Gobo Holder  
The TFX-FS360 can project one gobo image. A gobo-  
holder is included and is located directly underneath the  
followspot next to the fan as pictured here on the right.  
Remove the two bottom screws from the gobo-holder  
and slide it out. You can remove the gobo by sliding it  
out the top and replacing it with a different one or  
replace gobo-holder without a gobo for followspot only use.  
TFX-FS360 User Manual  
5
2010-07-20/14:53  
 
         
Mounting  
ORIENTATION  
This fixture may be mounted in any safe, position provided there is adequate room for ventilation.  
STATIC MOUNT  
Hanging Clamp  
The TFX-FS360 comes equipped with a yoke for pipe clamp  
installations. The yoke will provide for a static mount or installation of  
the followspot for pre-focused use. It is important never to obstruct the  
fan or vents pathway. Mount the fixture using, a suitable “C” or “O”  
type clamp. Adjust the angle of the fixture by loosening both knobs  
and tilting the fixture. After finding the desired position, retighten both  
knobs.  
Note!  
Clamp is sold separately.  
When selecting installation location, take into consideration lamp  
replacement access and routine maintenance.  
Safety cables should always be used.  
Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature  
changes or restricted ventilation.  
TRIPOD STAND WITH CASTERS CH-W28 (OPTIONAL)  
The CH-W28 is a multipurpose followspot/speaker stand with casters. Assemble tripod for use with  
casters as indicated in the CH-W28 manual.  
Yoke  
1. Mount yoke bracket so the bracket side  
runs across the bottom.  
2. Mount the followspot bracket onto the  
tripod mounting plate  
3. Align screw holes with mounting plate  
openings and fasten with supplied bolts.  
Mounting plate  
Please visit your participating dealer and ask  
for the CH-W28 Tripod from CHAUVET®. To  
locate a dealer near you contact CHAUVET®  
at (954) 929-1115, Toll Free (800) 762-1084  
TFX-FS360 User Manual  
6
2010-07-20/14:53  
 
       
OPERATING INSTRUCTIONS  
Operating Modes  
The TFX-FS360 can be operated in the following ways;  
As a manual followspot using on-board manual controls or slaved to a DMX-512 controller for cue  
changes.  
As a static spot controlled by a DMX-512 controller.  
Followspot Mode  
Enter Manual Mode by pressing the FUNCTION SELECT button until the MANUAL LED is turned  
on.  
BUTTONS  
DIMMER  
FUNCTION  
Min. and Max. buttons adjust the intensity of the light output respectively.  
The electronic shutter provides instant lights on or shuts all light output off for a  
blackout state.  
SHUTTER  
The following colors can be immediately selected by pressing each individual  
button:  
Color Buttons  
UV, Magenta, Orange, Yellow, Green, Blue, red and White  
FUNCTION  
UP/DOWN  
Press FUNCTION button to switch between manual and DMX control modes.  
The Up/Down buttons are available when in DMX mode. Press the UP and  
DOWN buttons to locate the DMX channel value desired.  
TFX-FS360 User Manual  
7
2010-07-20/14:53  
 
     
Operating Instructions  
DMX Mode  
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to  
customizing or creating a show. In this mode you will be able to control each individual trait of the  
fixture independently.  
SETTING THE STARTING ADDRESS  
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start  
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data  
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels  
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,  
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate  
the start address selected for future reference.  
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping  
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that  
will help you understand its use.  
The TFX-FS360 utilizes two DMX control channels.  
1) Press the FUNCTION button until the DMX Mode LED turns on.  
2) Press the UP or DOWN buttons until the starting channel address you desire is located on the  
digital display.  
TFX-FS360 User Manual  
8
2010-07-20/14:53  
 
   
APPENDIX  
DMX Primer  
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A  
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user  
must assign a starting address on the fixture that indicates the first channel reserved in the controller.  
There are many different types of DMX controllable fixtures and they all may vary in the total number  
of channels required. Choosing a start address should be planned in advance. Channels should  
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is  
set incorrectly. You can however, control multiple fixtures of the same type using the same starting  
address as long as the intended result is that of unison movement or operation. In other words, the  
fixtures will be slaved together and all respond exactly the same.  
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is  
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which  
the fixtures are connected is not important and has no effect on how a controller communicates to  
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures  
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The  
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+).  
FIXTURE LINKING  
Figure 1 - DMX connector configuration  
Resistance 120  
ohm 1/4w between  
pin 2 (DMX -) and  
pin 3 (DMX +) of  
the last fixture.  
1
3
2
COMMON  
DMX +  
1
3
1
3
INPUT  
OUTPUT  
Termination reduces signal errors and to  
avoid signal transmission problems and  
interference, it is always advisable to connect  
a DMX signal terminator.  
2
2
DMX -  
Note!  
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin  
adapter.  
The chart below details a proper cable conversion:  
3 PIN TO 5 PIN CONVERSION CHART  
CONDUCTOR  
GROUND/SHIELD  
DATA ( - )SIGNAL  
DATA ( + ) SIGNAL  
NOT USED  
3 Pin Female (output)  
5 Pin Male (Input)  
Pin 1  
Pin 1  
Pin 2  
Pin 3  
Pin 2  
Pin 3  
Pin 4  
NOT USED  
Pin 5  
TFX-FS360 User Manual  
9
2010-07-20/14:53  
 
     
Appendix  
DMX Channel Values  
Channel  
Value  
Function  
Color Wheel  
Open  
Red  
Blue  
Green  
000 031  
032 063  
064 095  
096 127  
128 159  
160 191  
191 223  
224 255  
1
Yellow  
Orange  
Magenta  
UV (Purple)  
Dimmer  
000 004  
005 249  
250 255  
No Output  
Closed > Open  
Full Output (100%)  
2
Gobos  
Maintenance  
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage  
and environment are contributing factors in determining frequency. As a general rule, fixtures should  
be cleaned at least twice a month. Dust build up reduces light output performance and can cause  
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off  
fixture before conducting maintenance.  
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust  
collected on external vents and internal components. Clean all glass when the fixture is cold with a  
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply  
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical  
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil  
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or  
becomes dirty, clean the lamps with an alcohol wipe.  
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to  
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:  
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s  
optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. Clean  
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.  
Returns Procedure  
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.  
Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #).  
Products returned without an RMA # will be refused. Call CHAUVET® and request RMA # prior to  
shipping the fixture. Be prepared to provide the model number, serial number and a brief description  
of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from  
inadequate packaging is the customer’s responsibility. CHAUVET® reserves the right to use its own  
discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is  
always a safe method to use.  
TFX-FS360 User Manual  
10  
2010-07-20/14:53  
 
       
Appendix  
Claims  
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be  
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and  
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim  
for items such as missing component/part, damage not related to shipping, and concealed damage,  
must be made within seven (7) days of receiving merchandise.  
General Troubleshooting  
Applies to  
Foggers  
& Snow  
Dimmers  
& Chaser  
Symptom  
Solution(s)  
Lights  
Controllers  
Auto shut off  
Check fan thermal switch reset  
Clean optical system or replace lamp  
Beam is very dim or not  
bright  
Breaker/Fuse keeps  
blowing  
Check total load placed on device  
Chase is too slow  
Check users manual for speed adjustment  
Device has no power  
Check for power on Mains.  
Check device’s fuse. (internal and/or external)  
Fixture is not responding  
Check DMX Dip switch settings for correct addressing  
Check DMX cables  
Check polarity switch settings  
Lamps cuts off  
sporadically  
Possible bad lamp or fixture is overheating.  
Lamp may be at end of its life.  
Light will not come on after  
power failure  
Some discharge lamps require a cooling off period before the  
electronics in the fixture can kick start it again, wait 5 to 10 minutes  
before powering up  
Loss of signal  
Use only DMX cables  
Install terminator  
Note: Keep DMX cables separated from power cables or black lights.  
Motor movements are  
jerky or jumpy  
Possible bad motor driver or sensors  
Check polarity switch on controller  
No flash  
Re-install bulb, may have shifted in shipping  
No light output  
Check slip ring & brushes for contact  
Install bulb  
Call service technician  
TFX-FS360 User Manual  
11  
2010-07-20/14:53  
 
   
Appendix  
Technical Specifications  
WEIGHT & DIMENSIONS  
Length....................................................................................................................... 572 mm (22.5 in)  
Width......................................................................................................................... 292 mm (11.5 in)  
Height ....................................................................................................................... 162 mm (6.38 in)  
Weight........................................................................................................................ 9.3 kg (20.6 lbs)  
POWER  
US.................................................................................................................................... 120 V, 60 Hz  
European Version ............................................................................................................ 230 V, 50 Hz  
AC input.......................................................................................3-prong IEC 60320 C14 male socket  
LIGHT SOURCE  
Lamp............................................................................................................. ENX, 360 W, 82 V, 75 hr,  
PHOTO OPTIC  
Luminance @ 1 m................................................................................................................ 48,420 lux  
Beam Angle .............................................................................................................................2° ~ 12°  
THERMAL  
Maximum ambient temperature......................................................................................40° C (104° F)  
CIRCUIT BREAKER  
Main @ 120 V ................................................................................................................................. 7 A  
Main @ 230 V ................................................................................................................................. 5 A  
CONTROL & PROGRAMMING  
Data input ............................................................................................. locking 3-pin XLR male socket  
Data output ........................................................................................ locking 3-pin XLR female socket  
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)  
Protocols.....................................................................................................................DMX-512 USITT  
DMX Channels....................................................................................................................................2  
ORDERING INFORMATION  
Followspot400G............................................................................................................. TFX-FS360  
Tripod Stand with Casters (optional)........................................................................................ CH-W28  
GOBO  
Outside diameter.....................................................................................................................35.8 mm  
Image diameter.......................................................................................................................27.9 mm  
Maximum thickness...................................................................................................................0.2 mm  
TFX-FS360 User Manual  
12  
2010-07-20/14:53  
 
 

Black Box Computer Accessories gigatrue cat6 component level patch panels User Manual
Blaupunkt Car Stereo System RPD 552 User Manual
Bowers Wilkins Speaker 2 SE User Manual
Braun Iron 4 695 User Manual
Briggs Stratton Lawn Mower MODEL 290000 User Manual
Broil King Gas Grill 9986 44 User Manual
Brother Printer 9200DX User Manual
Bryant Furnace 359AAV User Manual
Casio Time Clock MA0309 EA User Manual
CAT Portable Generator GT950 User Manual