Chief Manufacturing Indoor Furnishings PSH 2000 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
HEAVY DUTY FIXED WALL MOUNT  
Model: PSH-2000  
Specifications:  
Accomodates Akira and Orion 84" displays  
without interface bracket; accomodates other  
large flat panel displays with optional interface  
bracket.  
NOTE: Interface bracket, if required, will result in  
additional installation depth. Contact Chief for  
details.  
Designed for installation on dual wood studs (16"  
or 24" on center).  
Weight capacity of 250 lbs (113 kg).  
BEFORE YOU BEGIN  
CAUTION: To prevent damage to your display and this unit, which could affect or void the factory warranty,  
thoroughly study all instructions and illustrations before installation. Pay particular attention to the Warnings and  
Cautions in this document.  
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-  
6280.  
8805-000067 Rev F  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE 700  
SAVAGE, MINNESOTA 55378 USA  
©2006 Chief Manufacturing  
01/06  
 
Installation Instructions  
Model: PSH-2000  
TOOLS REQUIRED FOR INSTALLATION  
Drill and 7/32" drill bit  
13mm wrench  
Table 1: Parts  
1/2" wrench  
Item  
10  
Description  
Qty  
2
Phillips screwdriver, #2  
M5 Hex Key (provided)  
3/16" Hex Key (provided)  
5/32" Hex Key (provided)  
PLATE, Wall  
20  
BRACKET, Static  
BRACKET, Side Support  
LATCH  
2
30  
2
40  
2
50  
SPACER, 0.194" ID x 0.375" OD x 0.032"  
SCREW, Button Head Cap, 10-24 x 1/2"  
SCREW, Phillips Pan Machine, 10-24 x 1-1/2"  
SCREW, Button Head Cap, M8-1.25 x 25mm  
BUTTON, Mounting  
8
8
2
6
6
6
6
6
24  
1
1
1
8
NOTE: Other tools may be required depending on your  
method of installation.  
60  
70  
80  
PARTS  
90  
Unpack carton, inspect and verify contents  
100  
110  
120  
130  
140  
150  
160  
WASHER, Flat, Machine, M8  
(See Figure 1). Read installation instructions completely.  
If any listed parts are missing or damaged, contact Chief  
Customer Service at 1-800-582-6480.  
WASHER, Lock, Split, M8  
NUT, Hex, Finished Standard, M8  
SCREW, Button Head Cap, 5/16"-18 x 1/2"  
KEY, Hex, M5 (Slightly larger than 150)  
KEY, Hex, 3/16"  
KEY, Hex, 1/8"  
BOLTS, Hex Head Lag, 5/16" x 2-1/2"  
(Required, not supplied)  
WASHER, Flat, Machine, 5/16" (Required, not  
supplied)  
8
(20)  
(10)  
(30)  
(40)  
(50)  
(60)  
(70)  
(80)  
(90)  
(100)  
(110)  
(120)  
(130)  
(140)  
(150)  
(160)  
Figure 1: Parts  
3
 
 
Model: PSH-2000  
Installation Instructions  
ASSEMBLY AND INSTALLATION  
NOTE: Read the Warnings and Cautions on page 2.  
INSTALL MOUNTING BUTTONS  
Installation of the mounting buttons is dependent on your  
specific display. Three options are provided:  
Akira 84" and Orion 84" displays  
Modular 84" displays  
Other large flat panel displays  
Install buttons (90) at these  
6 mounting hole locations.  
AKIRA 84" AND ORION 84" DISPLAYS  
1. Using key (140), insert screw (80) through button (90)  
and install into threaded mounting hole on back of  
display (See Figure 2). Tighten securely.  
Figure 3: Modular Display Frame  
2. Repeat for remaining five buttons.  
(90)  
Mounting Hole  
(90)  
(80)  
(120)  
(110)  
(100)  
Modular  
Frame  
(80)  
Install buttons (90) at these  
6 mounting hole locations.  
Figure 4: Modular 84" Mounting Button  
OTHER LARGE FLAT PANEL DISPLAYS  
Figure 2: Akira 84" and Orion 84" Mounting Button  
1. Install the optional interface bracket to display  
according to the instructions provided with the  
interface bracket.  
MODULAR 84" DISPLAYS  
NOTE: Modular displays are four independent displays  
attached together within a single frame. The  
assembly performs as a single display.  
NOTE: Mounting buttons are pre-installed on optional  
interface bracket. PSH-2000 items (80) through  
(120), and key (140)(See Figure 1), will not be  
used with optional interface bracket.  
1. Insert screw (80) through button (90) and frame on  
back of modular display (See Figure 3)(See Figure 4).  
Using key (140) and 13mm wrench, install washer  
(100), washer (110), and nut (120). Tighten securely.  
2. Repeat for remaining five buttons.  
4
 
   
Installation Instructions  
Model: PSH-2000  
ASSEMBLE STATIC BRACKETS  
ASSEMBLE SIDE SUPPORTS  
1. Using key (160), loosely install screws (60) through  
latch (40) and spacers (50) into threaded holes in  
bracket (20) (See Figure 5). Ensure latch (40) is  
installed on the end of bracket (20) with the square  
cutout.  
1. Using key (150), loosely install support (30) to plate  
(10) with screws (130) (See Figure 7). Ensure lip of  
support (30) covers edge of plate (10).  
2. Repeat for other 3 corners.  
3. Once all screws (130) are installed, tighten securely.  
Threaded  
Hole in  
(40)  
(130)  
Bracket  
(4 Places)  
(10)  
(50)  
(4 Places)  
(60)  
(4 Places)  
Square  
Cutout  
(20)  
(30)  
Figure 5: Latch Assembly  
2. Repeat for remaining bracket (20).  
Figure 7: Side Support Assembly  
3. Tighten screws (60) only as required to keep latches  
(40) from freely slipping on bracket (20). Latches are  
designed to slide; do not overtighten screws (60).  
4. Slide latch (40) to fully open (raised) position.  
5. Using Phillips screwdriver, install screw (70) through  
slotted hole in latch (40) into threaded hole in bracket  
(20) (See Figure 6). Tighten only as required to take  
up slack; overtightening will close latch preventing  
mounting button installation.  
If latch begins to close, loosen screw (70) and pull  
latch (40) to open position.  
(70)  
Slotted Hole  
in Latch (40)  
Threaded Hole  
in Latch (40)  
Threaded Hole  
in Bracket (20)  
Figure 6: Open Latch  
5
 
     
Model: PSH-2000  
Installation Instructions  
INSTALL MOUNT TO WALL  
1. Determine approximate mounting location, keeping in  
mind the display size.  
Left of center installation  
Lag Bolt & Washer  
(8 Places)  
WARNING: The mount must be installed on two or  
three wood studs (or other equivalent vertical or  
horizontal supporting framework). Do not mount to  
single wood studs. Failure to properly install unit can  
result in serious personal injury or damage to  
equipment!  
2. Use a stud sensor to locate applicable wood studs.  
Mark locations with a pencil.  
3. Level mount at desired height per one of the  
configurations below:  
NOTE: Either configuration below provides ± 2" of lateral  
shift.  
Lag Bolt &  
Washer  
(8 Places)  
16" on center studs: The mount is approximately  
centered between two or three studs as shown  
Right of center installation  
24" on center studs: The mount is offset to the left  
or right of center between two studs as shown  
Figure 9: 24" On Center Installation  
4. Using mount as a template, mark the location of the  
pilot holes. Ensure the following:  
Centered between 2 studs  
Marks are in the center of wood studs.  
Lag Bolt &  
Washer  
(8 Places)  
8 pilot holes are marked (one in each slot).  
NOTE: For 16" on center, 3 stud installation: Lag bolts  
and washers on center stud are optional.  
5. Drill pilot holes using a 7/32" drill bit. Ensure pilot  
holes are straight.  
6. Using 1/2" wrench, install eight 5/16" x 2 ½" lag bolts  
and eight 5/16" washers through mounting holes and  
into pilot holes. Tighten all lag bolts.  
NOTE: Lag bolts and washers are not supplied.  
Lag Bolt &  
Washer  
(8 Places)  
Centered between 3 studs  
Figure 8: 16" On Center Stud Installation  
6
 
   
Installation Instructions  
Model: PSH-2000  
2. Using key (150), loosely install brackets (20) to plates  
(10) with screws (130) according to dimension noted  
in previous step. Ensure that brackets (20) are  
installed so that the latches (40) are towards the top  
of the mount.  
INSTALL STATIC BRACKETS  
AKIRA 84", ORION 84", AND MODULAR 84"  
DISPLAYS  
1. Using key (150), loosely install brackets (20) to plates  
(10) with screws (130) (See Figure 10). Ensure the  
following:  
14" horizontal dimension: Install brackets (20) to  
inside set of mounting holes, closest to center of  
mount (See Figure 12).  
Brackets (20) are installed to outside set of  
mounting holes, closest to supports (30).  
24" horizontal dimension: Install brackets (20) to  
middle set of mounting holes (See Figure 13).  
Brackets (20) are installed so that latches (40) are  
towards top of mount.  
33" horizontal dimension: Install brackets (20) to  
outside set of mounting holes, closest to supports  
2. Tighten all 16 screws (130) securely.  
3. Tighten all 16 screws (130) securely.  
(130)  
(16 Places)  
(130)  
(16 Places)  
Figure 10: Installation on Outside Mounting Holes  
OTHER LARGE FLAT PANEL DISPLAYS  
Figure 12: Installation on Inside Mounting Holes  
1. Determine horizontal dimension between mounting  
buttons on back of display (or interface bracket, if  
(130)  
(16 Places)  
Mounting Buttons  
(6 buttons shown;  
4 buttons similar)  
Figure 13: Installation on Middle Mounting Holes  
Back of Display  
Figure 11: Horizontal Dimension  
7
 
     
Model: PSH-2000  
Installation Instructions  
5. Repeat for second latch (40).  
INSTALL DISPLAY  
6. Connect cables to display as required.  
WARNING: Display is very heavy! Ensure display can  
be safely lifted and maneuvered as required to install  
on mount. Failure to take adequate precautions can  
result in serious personal injury or damage to  
equipment!  
REMOVE DISPLAY  
WARNING: Display is very heavy! Ensure display can  
be safely lifted and maneuvered as required to remove  
from mount. Failure to take adequate precautions can  
result in serious personal injury or damage to  
equipment!  
1. Ensure latches (40) are in fully open (raised) positions  
2. Note button openings to be used on each bracket (20)  
when installing display (See Figure 14).  
1. Disconnect all cables from display.  
2. Using Phillips screwdriver, fully remove screw (70)  
from threaded hole in bracket (20) (See Figure 6).  
3. Re-install screw (70) into threaded hole in latch (40).  
Turn screw (70) until latch (40) slides into fully open  
position.  
4. Repeat for second latch (40).  
5. Lift and maneuver display mounting buttons (90) out  
of button openings.  
Six  
Button  
Installation  
Four  
Button  
Installation  
(20)  
Figure 14: Mounting Holes  
3. Lift and maneuver display such that all buttons (90) fit  
into button openings on brackets (20). Lower display  
firmly into place. Ensure each button (90) has fully  
seated in its button opening.  
4. Using Phillips screwdriver, tighten screw (70) until  
latch (40) slides into closed position (See Figure 15).  
(70)  
(40)  
Figure 15: Closed Latch  
8
 
   

Belkin Switch SE 2 Port User Manual
Billy Goat Vacuum Cleaner DL1800V User Manual
Black Box Network Router LRA001A R2 User Manual
Bogen Stereo Equalizer PEQ1R User Manual
Boss Audio Systems Music Pedal RP250 User Manual
Cables Unlimited Speaker System SPK POOL User Manual
Cadco Food Warmer CBC SDC User Manual
Califone Home Theater System PA BT30 User Manual
Carrier Refrigerator 30HK User Manual
Chicago Electric Portable Generator 90300 User Manual