INSTRUCTION
MANUAL
3D-DNR
TRUE DAY/NIGHT IR CAMERA
MODEL HDC150
Copyright © 2009 Clover Electronics U.S.A. All Rights Reserved.
5. If necessary, change the settings to get the best images depending on your application
by using the button on the bottom of the camera.
- Get rid of the cap⑥ for the OSD button by turning counter-clockwise and then
change the settings (refer to the included instruction manual for OSD Control).
- Turn the cap⑥ clockwise to secure after changing the settings.
6. Connect the one end of 100’ cable (supplied) to the BNC (F) of 5’ cable attached to
the camera and the other end (BNC) of cable to the video devices such as DVR,
monitor/TV. Plug the provided AC power supply to the DC jack (red) on the end of
100’ cable.
HOW TO ADJUST ANGLE OF VIEW
1. Vari-focal lens①
Easily changeable angle of view: 2.8 to 12mm
2. Remove the sun-visor② and turn the locking screws on the knobs③ with the
provided hex-head wrench counter-clockwise to make easier adjustment for angle of
view. Do not stamp your fingerprint on the lens and the window, which may affect
picture quality.
3. T↔W (Tele ↔ Wide)⑤
Turn this adjustment ring⑤ clockwise or counter-clockwise to set the focal length.
4. ∞↔N④
Turn this adjustment ring④ clockwise or counter-clockwise to set the focus.
5. After setting the focus and focal length, the locking screws on the knobs③ should be
securely fastened.
Note:
▪ Apply the provided AC Power supply only.
▪ The total length of cable must not exceed 200’ including extension
cable.
TROUBLE SHOOTING
If the camera does not function properly, check the following points before contacting the
service center.
Troubles
Remedies
No video
Check the AC adapter and video cable
between the camera and a monitor
Check the brightness control on the
monitor
Check if the lens is stained. If dirty,
clean it with soft and clean cloth
The image on the screen is dark
The image on the screen is dim
The camera is not working properly, and Check if you have connected the
the surface of the camera case is hot
The contrast on the screen is too weak
provided AC adapter
Adjust the contrast feature of the
monitor. If the camera is exposed under
too strong light, change the position
Does the camera face to directly to the
sunlight or fluorescent light? Change the
camera position
The image on the screen flickers
Picture rolls and jumps, scrambled
picture
Improper V-hold control. Setting on your
monitor
Picture smaller than screen
House current may be too low
SPECIFICATIONS
• Image sensor
• Total pixels
• Effective Pixels
• Scanning system
• Synchronization
• O.S.D
1/3” SONY Super HAD CCD
811(H) x 508(V)
768(H) x 494(V)
2:1 Interlace
Internal/Line Lock
Available
• Backlight
• Resolution
• S/N (Y signal)
• Min.illumination
Off / HSBLC / BLC selectable
550TV Lines(color),600TV Lines(B/W)
52dB (AGC Off, Weight On)
0.00006Lux @F1.2 (sens-up:x258, IR LED:
ON)
• White Balance
• Sense-up
• 3 DNR
ATW / AWB / Manual / AWC→SET
Off / Auto / (Selectable limit x2 ~ x258)
Off / On (1~50 level adjustable)
Indoor / Outdoor / Off
• D-WDR
• D&N selection
• Digital zoom
• Voltage
• Current consumption
• Lens
• Operating temperature/Humidity
• Storage temperature/Humidity
• Dimensions
Color / BW / Auto
On(x32) / Off
AC 24V / DC 12V(Dual voltage)
LED On: 650 mA, LED Off: 180 mA
DC Auto Iris Varifocal Lens (2.8mm-12mm)
-10°C ~ +50°C. RH 95% Max.
-20°C ~ +60°C. RH 95% Max.
88 (W) x 105 (H) x 222 (D)mm
3.2 Lbs
• Weight
LIMITED 2 YEAR WARRANTY
This warranty gives the original purchaser specific legal rights and you may also have
other rights, which vary from state to state. If our products do not function because of any
defect in material or workmanship, we will repair free of charges for 2 years on parts and
labor from the date of original purchase. This warranty does not cover modification,
abuse, incidental or consequential damages unless the state of owner’s residence specially
prohibits limitations on incidental or consequential damages.
HOW TO OBTAIN FACTORY SERVICE
1. Original purchaser must fill out a warranty card and mail it to the factory with model
number, serial number and the date of purchase.
2. We will repair or replace, and return to the owner the system under this limited
warranty.
3. Please pack the system carefully and securely using the original packing materials,
and send it prepaid and insured to: 13073 E. 166th St, Cerritos, CA 90703.
4. Please include a check for $20.00 to cover the cost of return postage and handling. If
the system is returned within the warranty period, please include a proof of purchase.
If the system is out of warranty, you will receive an estimate of the repair cost for
your approval before repair work will be begun.
AVAILABLE ACCESSORIES
CDR0460
CDR4450
CDR0860
CDR1660
CDR0850
CDR1650
CA100BP
Stand-alone 4 CH Digital Video Recorder (DVR)
Stand-alone 4 CH Digital Video Recorder (DVR)
Stand-alone 8 CH Digital Video Recorder (DVR)
Stand-alone 16 CH Digital Video Recorder (DVR)
Stand-alone 8 CH Digital Video Recorder (DVR)
Stand-alone 16 CH Digital Video Recorder (DVR)
100’ BNC/Power to BNC/Power Extension cable and coupler
PACKAGE INCLUDES
1-True Day & Night Color Camera
1-Universal Mounting Bracket & 100’ BNC/Power to BNC/Power cable
1-UL Approved AC Power Supply
1-Hardware Accessories Kit
1-Instruction Manual
1-Instruction Manual for OSD Control
1-Warranty Registration Card
|