®
WEATHERMASTER 6 SCREENED TENT
MODEL 2000001597
Before you begin
6. Rotate all eight Leg Poles upright and insert
Read all instructions before set up.
pin on each web loop at the side locations
7A
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
as shown. (Fig. 7 & 7A)
Pin
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Pole
Pole
Fig. 7
Description
Qty. Dia.
Repair Kit Replacement Kit
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg
Poles to attach. (Fig. 8)
Long Leg Pole, steel
(w/ red marking)
Short Leg Pole, steel
Curved Ridge Pole, steel
(w/ red marking)
Curved Ridge Pole, steel
Awning Pole, black,
fiberglass, metal tips
Door Pole, long, thin, black,
fiberglass, rubber tips
Vert. Door Pole, short, black,
fiberglass, rubber tips
4
4
19mm
19mm
N/A
N/A
5010000608
5010000610
2
2
19mm
19mm
N/A
N/A
5010000607
5010000609
Fig. 8
Fig. 9
8. To stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
1
1
1
6.3mm 5010000543 5010000545
6.3mm 5010000543 5010000545
6.3mm 5010000543 5010000545
Upper
Leg Pole
Section
• Pull up on top Leg Pole section
until tent is taut;
• Twist the lower Leg Pole clock-
wise until the button locks into
the center or lowest hole;
Button
Center Hole
Lower Hole
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
Lower
door facing the desired direction. Unzip doors. (Fig. 1)
Leg Pole
Section
Fig. 1
• Repeat on remaining Leg Poles.
9. Insert plastic stakes through web
straps located on both sides of tent,
then drive in to secure. (Fig. 10)
Door
NOTE: It may be necessary to remove
metal stakes through web straps at
side of tent and screen room, pull tent
taut, and drive in stakes to secure.
2. Pull four corners of tent taut, then secure by
driving stakes through web loops at an angle
for better anchoring. (Fig. 2)
Fig. 10
Fig. 2
3. Assemble four, steel, shock-corded,
curved Ridge Poles. Insert Ridge Poles
(with red marking) into center sleeves
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
Fig. 3
Hinged, Rigid Door
Ridge Pole
with Red
Marking
1. Assemble Vertical Door Pole (shorter black pole with plastic
cap tips); then insert through zippered vertical pole sleeveon
hinged side of door. (Fig. 11)
Sleeve
with Red
Trim
2. Insert end of Vertical Door Pole into bottom hinge plate,
apply pressure to form a slight bow, then insert other tip of
pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips);
then insert into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure
to form a bow, then insert other tip of pole into the bottom
hinge. (Fig. 15)
4. Assemble eight, steel, shock-corded, Leg Poles. Push down
on steel button on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
Button in third hole
Fig. 4
(with red marking) into the ends of the
Ridge Poles (with red
marking). Insert curved
end of remaining short
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Fig. 12
Fig. 13
Ridge Pole with
Red Marking
Vertical Pole
Sleeve
Leg Poles into the ends
of the remaining Ridge
Poles. (Fig. 5 & 6)
Door Hinge
Sleeve
with Red
Trim
Curved End of
Long Leg Pole
Fig. 5
Fig. 6
Fig. 15
Fig. 14
Curved Ridge
Poles with Red
Marking in
center 2
Top
Door
Pole
Sleeve
Hinge
sleeves
Fig. 16
(continued on other side)
|