Craftsman Radio 13918152 User Manual

®
Universal Receiver  
Model 139.18152  
USER INSTRUCTIONS  
To prevent possible SERIOUS INJURY or DEATH from electrocution:  
• Be sure power is not connected BEFORE installing door control.  
• Connect ONLY to 24 VOLT low voltage wires.  
To prevent possible SERIOUS INJURY or DEATH from a closing garage  
door:  
• Install door control within sight of garage door, out of reach of  
children at a minimum height of 5 feet  
(1.5 m), and away from all moving parts of door.  
NOTICE TO U. S. CONSUMERS:  
Some states prohibit the service or repair of garage door motor units  
which cannot be made to comply with the safety standards contained in  
UL 325 (1988 revision). In order to comply with both the letter and the  
spirit of these laws, this universal remote control converter kit should  
not be used with any Sears Craftsman® garage door opener  
manufactured prior to April 1, 1982.  
• NEVER permit children to operate or play with door control push  
buttons or remote control transmitters.  
• Activate door ONLY when it can be seen clearly, is properly adjusted,  
and there are no obstructions to door travel.  
• ALWAYS keep garage door in sight until completely closed. NEVER  
permit anyone to cross path of closing garage door.  
Power Indicator Light  
Actuator Cover  
Terminals  
Bell Wire  
"SMART"  
Channels  
Indicator  
INSTALLATION  
Light  
• Unplug the motor unit before proceeding.  
Connect Bell Wire  
To Garage Door  
Opener Terminals  
• OPEN RECEIVER: Insert a small screwdriver in slot on  
receiver front panel as shown. Twist up actuator cover.  
• CONNECT RECEIVER AND MOTOR UNIT: Remove about  
1/4" of insulation from each end of the 2-strand bell wire.  
Connect one end to the receiver screw terminals (polarity is  
NOT required). Route wire along the channels and out the  
bottom as shown.  
"SMART"  
Actuator  
Bell Wire  
Universal Receiver  
3-Function  
Remote Control  
• Connect the other end of the bell wire to the two motor unit  
terminals labeled “2” (white) and “1” (red), “common” and  
“command” or the terminals used for the push button control.  
• Use insulated staples to secure bell wire between receiver and  
motor unit. Length of bell wire depends on where the receiver  
will be installed. Replace actuator cover.  
Select a  
push button  
"SMART"  
Actuator  
• Choose a 120Vac polarized outlet for the receiver which is  
OUT OF THE REACH OF CHILDREN. Plug receiver into  
selected outlet. Return power to the motor unit.  
Indicator Light  
PROGRAMMING THE REMOTE TO  
THE RECEIVER  
With Security®, the code between the remote control and the  
receiver changes with each use, accessing over 100 billion new  
codes.  
TO ERASE ALL REMOTE CONTROL CODES  
Press and hold the “SMART” actuator on the receiver panel until  
the indicator light turns off (about 6 seconds). All transmitter codes  
are now erased. Then follow the steps above to reprogram each  
remote control.  
You can activate your motor unit with up to 8 Security® remote  
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this  
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the  
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.  
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the  
following two conditions: (1) this device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired operation.  
controls and one Security® Keyless Entry.  
1. Pry open the front panel of receiver case with a screwdriver.  
Re-connect power to motor unit.  
2. Press and release the “SMART” actuator on the receiver. The  
learn indicator light will glow steadily for 30 seconds.  
3. Within 30 seconds, press and hold the button on the hand-held  
remote that you wish to operate your garage door.  
To order replacement parts call...  
1-800-4-MY-HOME (1-800-469-4663)  
®
The motor unit will now operate when either the receiver actuator  
or the remote control push button is pressed.  
Repeat Steps 2 and 3 for each remote control that will be used to  
operate the garage door motor unit.  
 

COBY electronic Washer MP 705 1G User Manual
Cooper Lighting Indoor Furnishings 1183 User Manual
Craftsman Lawn Sweeper 486242112 User Manual
Danby Freezer DUF419W User Manual
Desa Water Heater CFN2800BTB User Manual
DigiPower Battery Charger JS TALK User Manual
Dyson Vacuum Cleaner DC15 User Manual
Extron electronic Stereo Receiver FOX 2G Rx AV User Manual
Fusion Marine Radio MS NRX200 User Manual
Global Machinery Company Saw LS211 User Manual