Cypress Computer Hardware 7C185 15 User Manual

185  
CY7C185  
8K x 8 Static RAM  
provided by an active LOW chip enable (CE ), an active HIGH  
Features  
1
chip enable (CE ), and active LOW output enable (OE) and  
2
• High speed  
— 15 ns  
three-state drivers. This device has an automatic power-down  
feature (CE or CE ), reducing the power consumption by 70%  
1
2
when deselected. The CY7C185 is in a standard 300-mil-wide  
DIP, SOJ, or SOIC package.  
• Fast t  
DOE  
• Low active power  
An active LOW write enable signal (WE) controls the writ-  
— 715 mW  
ing/reading operation of the memory. When CE and WE in-  
1
• Low standby power  
puts are both LOW and CE is HIGH, data on the eight data  
2
input/output pins (I/O through I/O ) is written into the memory  
0
7
— 220 mW  
location addressed by the address present on the address  
• CMOS for optimum speed/power  
• Easy memory expansion with CE , CE , and OE features  
pins (A through A ). Reading the device is accomplished by  
0
12  
selecting the device and enabling the outputs, CE and OE  
1
2
1
• TTL-compatible inputs and outputs  
• Automatic power-down when deselected  
active LOW, CE active HIGH, while WE remains inactive or  
2
HIGH. Under these conditions, the contents of the location ad-  
dressed by the information on address pins are present on the  
eight data input/output pins.  
Functional Description[1]  
The input/output pins remain in a high-impedance state unless  
the chip is selected, outputs are enabled, and write enable  
(WE) is HIGH. A die coat is used to insure alpha immunity.  
The CY7C185 is a high-performance CMOS static RAM orga-  
nized as 8192 words by 8 bits. Easy memory expansion is  
Logic Block Diagram  
Pin Configurations  
DIP/SOJ/SOIC  
Top View  
NC  
V
CC  
1
2
3
4
28  
27  
26  
25  
24  
23  
22  
21  
20  
19  
18  
17  
16  
15  
A
WE  
CE  
4
A
5
2
A
A
3
6
A
A
2
A
1
7
5
I/O  
I/O  
0
A
8
6
7
8
9
10  
11  
12  
13  
14  
A
9
OE  
INPUT BUFFER  
A
A
A
A
0
10  
11  
12  
1
CE  
1
I/O  
7
I/O  
6
I/O  
5
I/O  
4
I/O  
3
A
1
A
2
I/O  
0
I/O  
1
I/O  
2
I/O  
I/O  
2
A
3
3
GND  
A
256 x 32 x 8  
ARRAY  
4
A
5
I/O  
I/O  
I/O  
I/O  
4
5
6
7
A
6
A
7
A
8
POWER  
DOWN  
CE  
1
COLUMN DECODER  
CE  
2
WE  
OE  
Selection Guide[2]  
7C185-15  
15  
7C185-20  
20  
7C185-25  
25  
7C185-35  
35  
Maximum Access Time (ns)  
Maximum Operating Current (mA)  
130  
110  
100  
100  
Maximum Standby Current (mA)  
40/15  
20/15  
20/15  
20/15  
Note:  
1. For guidelines on SRAM system design, please refer to the System Design GuidelinesCypress application note, available on the internet at www.cypress.com.  
2. For military specifications, see the CY7C185A data sheet.  
Cypress Semiconductor Corporation  
3901 North First Street  
San Jose  
CA 95134  
408-943-2600  
Document #: 38-05043 Rev. *A  
Revised September 13, 2002  
 
CY7C185  
Electrical Characteristics Over the Operating Range (continued)  
7C185-25  
7C185-35  
Parameter  
Description  
Test Conditions  
= Min., I = 4.0 mA  
Min.  
Max.  
Min.  
Max.  
Unit  
V
V
Output HIGH Voltage  
Output LOW Voltage  
Input HIGH Voltage  
V
V
2.4  
2.4  
OH  
OL  
IH  
CC  
OH  
V
V
= Min., I = 8.0 mA  
0.4  
0.4  
V
CC  
OL  
2.2  
V
+
2.2  
V
+
V
CC  
CC  
0.3V  
0.3V  
[3]  
V
Input LOW Voltage  
0.5  
5  
0.8  
+5  
+5  
0.5  
5  
0.8  
+5  
+5  
V
IL  
I
I
Input Load Current  
GND V V  
CC  
µA  
µA  
IX  
I
Output Leakage  
Current  
GND V V ,  
CC  
5  
5  
OZ  
I
Output Disabled  
I
I
I
I
Output Short  
Circuit Current  
V
V
= Max.,  
300  
100  
20  
300  
100  
20  
mA  
mA  
mA  
mA  
OS  
CC  
[4]  
= GND  
OUT  
V
Operating  
V
= Max.,  
= 0 mA  
CC  
CC  
CC  
Supply Current  
I
OUT  
Automatic  
Power-Down Current  
Max. V , CE V or CE V  
CC IH IL  
Min. Duty Cycle = 100%  
SB1  
SB2  
1
2
Automatic  
Max. V , CE V 0.3V  
15  
15  
CC  
1
CC  
Power-Down Current  
or CE 0.3V  
2
V
V 0.3V or V 0.3V  
IN  
CC IN  
Capacitance[5]  
Parameter  
Description  
Input Capacitance  
Output Capacitance  
Test Conditions  
T = 25°C, f = 1 MHz,  
Max.  
Unit  
C
C
7
7
pF  
pF  
IN  
A
V
= 5.0V  
CC  
OUT  
Note:  
5. Tested initially and after any design or process changes that may affect these parameters.  
AC Test Loads and Waveforms  
R1 481  
R1 481Ω  
5V  
5V  
ALL INPUT PULSES  
90%  
OUTPUT  
OUTPUT  
3.0V  
GND  
90%  
10%  
30 pF  
5 pF  
R2  
255Ω  
R2  
255Ω  
10%  
INCLUDING  
JIG AND  
SCOPE  
INCLUDING  
JIGAND  
5 ns  
5 ns  
SCOPE  
(a)  
(b)  
Equivalent to:  
THÉVENIN EQUIVALENT  
167Ω  
OUTPUT  
1.73V  
Document #: 38-05043 Rev. *A  
Page 3 of 11  
 
CY7C185  
[6]  
Switching Characteristics Over the Operating Range  
7C185-15  
Min. Max.  
7C185-20  
Min. Max.  
7C185-25  
Min. Max.  
7C185-35  
Min. Max.  
Parameter  
Description  
Unit  
Read Cycle  
t
t
t
t
t
t
t
t
t
t
t
Read Cycle Time  
15  
3
20  
5
25  
5
35  
5
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
RC  
Address to Data Valid  
15  
20  
25  
35  
AA  
Data Hold from Address Change  
OHA  
CE LOW to Data Valid  
15  
15  
8
20  
20  
9
25  
25  
12  
35  
35  
15  
ACE1  
ACE2  
DOE  
1
CE HIGH to Data Valid  
2
OE LOW to Data Valid  
OE LOW to Low Z  
3
3
3
3
LZOE  
HZOE  
LZCE1  
LZCE2  
HZCE  
[7]  
OE HIGH to High Z  
7
7
8
8
10  
10  
10  
10  
[8]  
CE LOW to Low Z  
3
3
5
3
5
3
5
3
1
CE HIGH to Low Z  
2
[7, 8]  
CE HIGH to High Z  
1
CE LOW to High Z  
2
t
t
CE LOW to Power-Up  
0
0
0
0
ns  
ns  
PU  
PD  
1
CE to HIGH to Power-Up  
2
CE HIGH to Power-Down  
15  
20  
20  
20  
1
CE LOW to Power-Down  
2
[9]  
Write Cycle  
t
t
t
t
t
t
t
t
t
t
t
Write Cycle Time  
15  
12  
12  
12  
0
20  
15  
15  
15  
0
25  
20  
20  
20  
0
35  
20  
20  
25  
0
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
WC  
CE LOW to Write End  
SCE1  
SCE2  
AW  
1
CE HIGH to Write End  
2
Address Set-up to Write End  
Address Hold from Write End  
Address Set-up to Write Start  
WE Pulse Width  
HA  
0
0
0
0
SA  
12  
8
15  
10  
0
15  
10  
0
20  
12  
0
PWE  
SD  
Data Set-up to Write End  
Data Hold from Write End  
0
HD  
[7]  
WE LOW to High Z  
7
7
7
8
HZWE  
WE HIGH to Low Z  
3
5
5
5
LZWE  
Notes:  
6. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified  
IOL/IOH and 30-pF load capacitance.  
7. tHZOE, tHZCE, and tHZWE are specified with CL = 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady state voltage.  
8. At any given temperature and voltage condition, tHZCE is less than tLZCE1 and tLZCE2 for any given device.  
9. The internal write time of the memory is defined by the overlap of CE1 LOW, CE2 HIGH, and WE LOW. All 3 signals must be active to initiate a write and either  
signal can terminate a write by going HIGH. The data input set-up and hold timing should be referenced to the rising edge of the signal that terminates the write.  
Document #: 38-05043 Rev. *A  
Page 4 of 11  
 
CY7C185  
Switching Waveforms  
[10,11]  
Read Cycle No.1  
t
RC  
ADDRESS  
t
AA  
t
OHA  
DATA OUT  
PREVIOUS DATA VALID  
DATA VALID  
[12,13]  
Read Cycle No.2  
t
RC  
CE  
1
CE  
2
t
ACE  
OE
t
HZOE  
t
DOE  
t
HZCE  
t
LZOE  
HIGH  
IMPEDANCE  
HIGH IMPEDANCE  
DATA OUT  
DATA VALID  
t
LZCE  
t
PD  
t
PU  
ICC  
ISB  
V
CC  
SUPPLY  
CURRENT  
50%  
50%  
[11,13]  
Write Cycle No. 1 (WE Controlled)  
t
WC  
ADDRESS  
t
CE  
1
SCEI  
t
t
HA  
AW  
t
CE  
SCE2  
2
t
SA  
t
PWE  
WE  
OE  
t
SD  
t
HD  
DATA VALID  
NOTE 14  
t
IN  
DATA I/O  
HZOE  
10. Device is continuously selected. OE, CE1 = VIL. CE2 = VIH  
.
11. WE is HIGH for read cycle.  
12. Data I/O is High Z if OE = VIH, CE1 = VIH, WE = VIL, or CE2=VIL  
.
13. The internal write time of the memory is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. CE1 and WE must be LOW and CE2 must be HIGH  
to initiate write. A write can be terminated by CE1 or WE going HIGH or CE2 going LOW. The data input set-up and hold timing should be referenced to the  
rising edge of the signal that terminates the write.  
14. During this period, the I/Os are in the output state and input signals should not be applied.  
Document #: 38-05043 Rev. *A  
Page 5 of 11  
 
CY7C185  
Switching Waveforms (continued)  
[13,14,15]  
rite Cycle No. 2 (CE Controlled)  
t
WC  
ADDRESS  
t
t
CE  
1
SCE1  
t
SA  
SCE2  
CE  
2
t
t
HA  
AW  
WE  
t
t
HD  
SD  
DATA VALID  
DATA I/O  
IN  
[13,14,15,16]  
Write Cycle No. 3 (WE Controlled, OE LOW)  
t
WC  
ADDRESS  
t
CE  
SCE1  
1
t
CE  
SCE2  
2
t
t
HA  
AW  
t
SA  
WE  
t
t
HD  
SD  
DATA I/O  
DATA VALID  
NOTE 14  
IN  
t
t
LZWE  
HZWE  
Notes:  
15. The minimum write cycle time for write cycle #3 (WE controlled, OE LOW) is the sum of tHZWE and tSD  
.
16. If CE1 goes HIGH or CE2 goes LOW simultaneously with WE HIGH, the output remains in a high-impedance state.  
Document #: 38-05043 Rev. *A  
Page 6 of 11  
 
CY7C185  
Typical DC and AC Characteristics  
NORMALIZED SUPPLY CURRENT  
vs. AMBIENT TEMPERATURE  
OUTPUT SOURCE CURRENT  
vs. OUTPUT VOLTAGE  
NORMALIZED SUPPLY CURRENT  
vs. SUPPLY VOLTAGE  
120  
100  
80  
1.4  
1.2  
1.0  
1.2  
1.0  
0.8  
I
I
CC  
CC  
0.8  
0.6  
0.4  
V
T
A
=5.0V  
=25°C  
CC  
0.6  
0.4  
60  
40  
V
V
=5.0V  
=5.0V  
CC  
IN  
0.2  
0.0  
20  
0
I
0.2  
0.0  
SB  
I
SB  
55  
25  
125  
0.0  
1.0  
2.0  
3.0  
4.0  
4.0  
4.5  
5.0  
5.5  
6.0  
AMBIENT TEMPERATURE (°C)  
OUTPUT VOLTAGE (V)  
SUPPLY VOLTAGE (V)  
NORMALIZED ACCESS TIME  
vs. AMBIENT TEMPERATURE  
OUTPUT SINK CURRENT  
vs. OUTPUT VOLTAGE  
NORMALIZED ACCESS TIME  
vs. SUPPLY VOLTAGE  
140  
120  
1.6  
1.4  
1.4  
1.3  
1.2  
100  
80  
V
CC  
=5.0V  
1.2  
1.0  
T =25°C  
A
1.1  
1.0  
60  
T =25°C  
A
V
CC  
=5.0V  
40  
0.8  
20  
0
0.9  
0.8  
0.6  
55  
0.0  
1.0  
2.0  
3.0  
4.0  
25  
125  
4.0  
4.5  
5.0  
5.5  
6.0  
OUTPUT VOLTAGE (V)  
SUPPLY VOLTAGE (V)  
AMBIENT TEMPERATURE (°C)  
TYPICAL POWER-ON CURRENT  
vs. SUPPLY VOLTAGE  
TYPICAL ACCESS TIME CHANGE  
vs. OUTPUT LOADING  
NORMALIZED I vs. CYCLE TIME  
CC  
3.0  
2.5  
2.0  
1.5  
30.0  
25.0  
20.0  
15.0  
1.25  
1.00  
0.75  
0.50  
V
=5.0V  
CC  
T =25°C  
A
V
CC  
=0.5V  
1.0  
0.5  
0.0  
10.0  
5.0  
V
=4.5V  
CC  
T =25°C  
A
0.0  
0.0  
1.0  
2.0  
3.0  
4.0  
5.0  
0
200 400  
600 800 1000  
10  
20  
30  
40  
SUPPLY VOLTAGE (V)  
CAPACITANCE (pF)  
CYCLE FREQUENCY (MHz)  
Document #: 38-05043 Rev. *A  
Page 7 of 11  
 
CY7C185  
Truth Table  
CE  
H
X
CE  
X
WE  
X
OE  
X
Input/Output  
Mode  
Deselect/Power-Down  
1
2
High Z  
High Z  
L
X
X
Deselect/Power-Down  
L
H
H
L
Data Out  
Data In  
High Z  
Read  
L
H
L
X
Write  
L
H
H
H
Deselect  
Address Designators  
Address  
Name  
Address  
Function  
Pin  
Number  
A4  
A5  
X3  
X4  
X5  
X6  
X7  
Y1  
Y4  
Y3  
Y0  
Y2  
X0  
X1  
X2  
2
3
A6  
4
A7  
5
A8  
6
A9  
7
A10  
A11  
A12  
A0  
8
9
10  
21  
23  
24  
25  
A1  
A2  
A3  
Ordering Information  
Speed  
(ns)  
Package  
Name  
Operating  
Range  
Ordering Code  
Package Type  
15  
CY7C185-15PC  
CY7C185-15SC  
CY7C185-15VC  
CY7C185-15VI  
CY7C185-20PC  
CY7C185-20SC  
CY7C185-20VC  
CY7C185-20VI  
CY7C185-25PC  
CY7C185-25SC  
CY7C185-25VC  
CY7C185-25VI  
CY7C185-35PC  
CY7C185-35SC  
CY7C185-35VC  
CY7C185-35VI  
P21  
S21  
V21  
V21  
P21  
S21  
V21  
V21  
P21  
S21  
V21  
V21  
P21  
S21  
V21  
V21  
28-Lead (300-Mil) Molded DIP  
28-Lead Molded SOIC  
28-Lead Molded SOJ  
Commercial  
28-Lead Molded SOJ  
Industrial  
20  
25  
35  
28-Lead (300-Mil) Molded DIP  
28-Lead Molded SOIC  
28-Lead Molded SOJ  
Commercial  
28-Lead Molded SOJ  
Industrial  
28-Lead (300-Mil) Molded DIP  
28-Lead Molded SOIC  
28-Lead Molded SOJ  
Commercial  
28-Lead Molded SOJ  
Industrial  
28-Lead (300-Mil) Molded DIP  
28-Lead Molded SOIC  
28-Lead Molded SOJ  
Commercial  
28-Lead Molded SOJ  
Industrial  
Document #: 38-05043 Rev. *A  
Page 8 of 11  
 
CY7C185  
Package Diagrams  
28-Lead (300-Mil) Molded DIP P21  
51-85014-*B  
28-Lead (300-Mil) Molded SOIC S21  
51-85026-*A  
Document #: 38-05043 Rev. *A  
Page 9 of 11  
 
CY7C185  
Package Diagrams (continued)  
28-Lead (300-Mil) Molded SOJ V21  
51-85031-*B  
All product and company names mentioned in this document may be the trademarks of their respective holders.  
Document #: 38-05043 Rev. *A  
Page 10 of 11  
© Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use  
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize  
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress  
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.  
 
CY7C185  
Document History Page  
Document Title: CY7C185 8K x 8 Static RAM  
Document Number: 38-05043  
Issue  
Orig. of  
Change  
REV.  
**  
*A  
ECN NO. Date  
Description of Change  
107145  
116470  
09/10/01  
09/16/02  
SZV  
CEA  
Change from Spec number: 38-00037 to 38-05043  
Add applications foot note to data sheet.  
Document #: 38-05043 Rev. *A  
Page 11 of 11  
 

Cooper Lighting Indoor Furnishings Ceiling Systems User Manual
Country Home Products Lawn Mower SUBURBANTM User Manual
Craftsman Blower 31679479 User Manual
Craftsman Lawn Mower 247370251 User Manual
Creative Car Speaker T6200 User Manual
Cuisinart Blender CSB 80 User Manual
Dacor Cooktop CER304 User Manual
Extron electronic Stereo Receiver FOX HD SDI User Manual
Fisher Paykel Food Warmer W860SD User Manual
GE Air Cleaner SERIES B 480 User Manual