CY7C1024DV33
3-Mbit (128K X 24) Static RAM
Features
Functional Description
■
■
■
High speed
tAA = 10 ns
Low active power
ICC = 175 mA at 10 ns
Low CMOS standby power
ISB2 = 25 mA
The CY7C1024DV33 is a high performance CMOS static RAM
organized as 128K words by 24 bits. This device has an
automatic power down feature that significantly reduces power
consumption when deselected.
❐
❐
To write to the device, enable the chip (CE1 LOW, CE2 HIGH,
and CE3 LOW), while forcing the Write Enable (WE) input LOW.
❐
To read from the device, enable the chip by taking CE1 LOW, CE2
7 for a complete description of Read and Write modes.
■
■
■
■
■
■
Operating voltages of 3.3 ± 0.3V
2.0V data retention
The 24 I/O pins (I/O0 to I/O23) are placed in a high impedance
state when the device is deselected (CE1 HIGH, CE2 LOW, or
CE3 HIGH) or when the output enable (OE) is HIGH during a
write operation. (CE1 LOW, CE2 HIGH, CE3 LOW, and WE
LOW).
Automatic power down when deselected
TTL compatible inputs and outputs
Easy memory expansion with CE1, CE2, and CE3 features
Available in Pb-free standard 119-ball PBGA
Logic Block Diagram
INPUT BUFFER
I/O0 – I/O23
128K x 24
ARRAY
A(9:0)
CE1, CE2, CE3
COLUMN
DECODER
WE
CONTROL LOGIC
OE
A(16:10)
Cypress Semiconductor Corporation
Document Number: 001-08353 Rev. *C
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised November 6, 2008
CY7C1024DV33
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage............. ...............................>2001V
(MIL-STD-883, Method 3015)
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied ............................................ –55°C to +125°C
Latch Up Current..................................................... >200 mA
Operating Range
Ambient
Temperature
Range
VCC
Industrial
–40°C to +85°C
3.3V ± 0.3V
DC Electrical Characteristics
Over the Operating Range
–10
Parameter
Description
Test Conditions [3]
Unit
Min
Max
VOH
VOL
VIH
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
VCC = Min, IOH = –4.0 mA
VCC = Min, IOL = 8.0 mA
2.4
V
V
0.4
VCC + 0.3
0.8
2.0
–0.3
–1
V
[2]
VIL
V
IIX
Input Leakage Current
Output Leakage Current
GND < VI < VCC
+1
μA
μA
mA
IOZ
ICC
GND < VOUT < VCC, output disabled
–1
+1
VCC Operating Supply
Current
VCC = Max, f = fMAX = 1/tRC
IOUT = 0 mA CMOS levels
175
ISB1
ISB2
Automatic CE Power Down Max VCC, CE > VIH
30
25
mA
mA
Current —TTL Inputs
VIN > VIH or VIN < VIL, f = fMAX
Automatic CE Power Down Max VCC, CE > VCC – 0.3V,
Current — CMOS Inputs
VIN > VCC – 0.3V, or VIN < 0.3V, f = 0
Capacitance
Tested initially and after any design or process changes that may affect these parameters.
Parameter
CIN
Description
Input Capacitance
I/O Capacitance
Test Conditions
Max
Unit
TA = 25°C, f = 1 MHz, VCC = 3.3V
8
pF
pF
COUT
10
Thermal Resistance
Tested initially and after any design or process changes that may affect these parameters.
119-Ball
PBGA
Parameter
Description
Test Conditions
Unit
ΘJA
Thermal Resistance
(Junction to Ambient)
Still air, soldered on a 3 × 4.5 inch,
four layer printed circuit board
20.31
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
8.35
°C/W
Notes
2.
V
(min) = –2.0V and V (max) = V + 2V for pulse durations of less than 20 ns.
IH CC
IL
3. CE refers to a combination of CE , CE , and CE . CE is LOW when CE , CE are LOW and CE is HIGH. CE is HIGH when CE is HIGH, or CE is LOW, or CE is HIGH.
1
2
3
1
3
2
1
2
3
Document Number: 001-08353 Rev. *C
Page 3 of 9
CY7C1024DV33
50Ω
R1 317 Ω
3.3V
= 1.5V
VTH
OUTPUT
OUTPUT
Z = 50Ω
0
30 pF*
R2
351Ω
5 pF*
*
Including jig
(a)
and scope
(b)
*Capacitive Load consists of all
components of the test environment
All input pulses
3.0V
90%
10%
90%
10%
GND
Rise Time > 1V/ns
Fall Time:> 1V/ns
(c)
AC Switching Characteristics
–10
Parameter
Description
Unit
Max
Min
Read Cycle
[6]
tpower
tRC
VCC(Typical) to the First Access
100
10
μs
Read Cycle Time
ns
tAA
Address to Data Valid
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tOHA
tACE
tDOE
tLZOE
tHZOE
tLZCE
tHZCE
tPU
Data Hold from Address Change
OE LOW to Data Valid
3
10
5
1
3
0
5
5
tPD
10
Notes
4. Valid SRAM operation does not occur until the power supplies have reached the minimum operating V (3.0V). 100 μs (t
) after reaching the minimum operating
DD
power
V
, normal SRAM operation can begin including reduction in V to the data retention (V
, 2.0V) voltage.
DD
DD
CCDR
5. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, and input pulse levels of 0 to 3.0V. Test conditions for the read cycle use
6.
7.
t
gives the minimum amount of time that the power supply is at typical V values until the first memory access is performed.
CC
POWER
, t
t
, t
, t
, t
, and t
are specified with a load capacitance of 5 pF as in part (b) of Figure 2. Transition is measured ±200 mV from steady state
HZOE HZCE HZWE LZOE LZCE
LZWE
voltage.
8. These parameters are guaranteed by design and are not tested.
Document Number: 001-08353 Rev. *C
Page 4 of 9
CY7C1024DV33
AC Switching Characteristics (continued)
Over the Operating Range [5]
–10
Parameter
Description
Unit
Min
Max
tWC
tSCE
tAW
Write Cycle Time
10
7
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Address Setup to Write End
Address Hold from Write End
Address Setup to Write Start
WE Pulse Width
7
tHA
0
tSA
0
tPWE
tSD
7
Data Setup to Write End
Data Hold from Write End
5.5
0
tHD
tLZWE
tHZWE
3
5
Data Retention Characteristics
Over the Operating Range
Parameter
VDR
Description
VCC for Data Retention
Min
Typ
Max
Unit
2
V
ICCDR
Data Retention Current
VCC = 2V, CE > VCC – 0.2V,
VIN > VCC – 0.2V or VIN < 0.2V
25
mA
[11]
tCDR
Chip Deselect to Data Retention Time
Operation Recovery Time
0
ns
ns
[12]
tR
tRC
Data Retention Waveform
DATA RETENTION MODE
3.0V
3.0V
VCC
CE
V
DR
>
2V
t
t
R
CDR
Notes
9. The internal write time of the memory is defined by the overlap of CE and CE and CE LOW and WE LOW. Chip enables must be active and WE must be LOW to
1
2
3
initiate a write. The transition of any of these signals terminate the write. The input data setup and hold timing is referenced to the leading edge of the signal that
terminates the write.
10. The minimum write cycle time for Write Cycle No. 3 (WE controlled, OE LOW) is the sum of t
11. Tested initially and after any design or process changes that may affect these parameters.
and t
.
HZWE
SD
12. Full device operation requires linear V ramp from V to V
> 50 μs or stable at V
> 50 μs.
CC(min)
CC
DR
CC(min)
Document Number: 001-08353 Rev. *C
Page 5 of 9
CY7C1024DV33
Switching Waveforms
tRC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
DATA VALID
ADDRESS
CE
t
RC
t
ACE
OE
t
HZOE
t
DOE
t
HZCE
t
LZOE
HIGH
IMPEDANCE
HIGH IMPEDANCE
DATA OUT
DATA VALID
t
LZCE
t
PD
V
CC
ICC
t
PU
SUPPLY
CURRENT
50%
50%
ISB
t
WC
ADDRESS
CE
t
SCE
t
SA
t
SCE
t
t
HA
AW
t
PWE
WE
t
t
HD
SD
DATA I/O
DATA VALID
Notes
13. Device is continuously selected. OE, CE = V .
IL
14. WE is HIGH for read cycle.
15. Address valid before or similar to CE transition LOW.
16. Data I/O is high impedance if OE = V
.
IH
17. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high impedance state.
Document Number: 001-08353 Rev. *C
Page 6 of 9
CY7C1024DV33
Switching Waveforms (continued)
t
WC
ADDRESS
CE
t
SCE
t
t
HA
AW
t
t
PWE
SA
WE
OE
t
t
SD
HD
DATA VALID
IN
DATA I/O
NOTE 18
t
HZOE
t
WC
ADDRESS
CE
t
SCE
t
t
HA
AW
t
SA
t
PWE
WE
t
t
HD
SD
DATA I/O
NOTE 18
DATA VALID
t
t
LZWE
HZWE
Truth Table
CE1
H
X
CE2
X
CE3
X
OE
WE
X
I/O0 – I/O23
Mode
Power
X
X
X
L
High Z
High Z
High Z
Power Down
Power Down
Power Down
Read
Standby (ISB
)
)
)
L
X
X
Standby (ISB
Standby (ISB
X
X
H
L
X
L
H
H
Full Data Out
Full Data In
High Z
Active (ICC
)
)
)
L
H
L
X
H
L
Write
Active (ICC
L
H
L
H
Selected, Outputs Disabled Active (ICC
Note
18. During this period, the I/Os are in the output state and input signals are not applied.
Document Number: 001-08353 Rev. *C
Page 7 of 9
CY7C1024DV33
Ordering Information
Speed
Package
Name
Operating
Range
Ordering Code
(ns)
Package Type
10
CY7C1024DV33-10BGXI
51-85115 119-Ball Plastic Ball Grid Array (14 x 22 x 2.4 mm) (Pb-Free) Industrial
Package Diagram
Figure 8. 119-Ball PBGA (14 x 22 x 2.4 mm)
51-85115-*B
Document Number: 001-08353 Rev. *C
Page 8 of 9
CY7C1024DV33
Document History Page
Document Title: CY7C1024DV33, 3-Mbit (128K X 24) Static RAM
Document Number: 001-08353
Orig. of
Change
Submission
Date
Rev. ECN No.
Description of Change
**
469517
499604
NXR
NXR
See ECN New data sheet
*A
See ECN Added note 1 for NC pins
Changed ICC specification from 150 mA to 185 mA
Updated Test Condition for ICC in DC Electrical Characteristics table
Added note for tACE, tLZCE, tHZCE, tPU, tPD, tSCE in AC Switching Characteristics Table
on page 4
*B
*C
1462586 VKN/SFV
2604677 VKN/PYRS
See ECN Converted from preliminary to final
Updated block diagram
Changed ICC specification from 185 mA to 225 mA
Updated thermal specs
11/12/08 Removed Commercial operating range, Added Industrial operating range
Removed 8 ns speed bin, Added 10 ns speed bin
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
PSoC Solutions
General
Clocks & Buffers
Wireless
Low Power/Low Voltage
Precision Analog
LCD Drive
Memories
Image Sensors
CAN 2.0b
USB
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-08353 Rev. *C
Revised November 6, 2008
Page 9 of 9
All product and company names mentioned in this document are the trademarks of their respective holders.
|