RDW24I, RDW24S
Document # PG10-007
Revised 03/12/12 Page 1/3
PLANNING
GUIDE
Renaissance® 24” Wide
Built-In Dishwasher
Product tolerances: ±1/16” (±1.6 mm)
otherwise stated
Product Dimensions
WaRnIng
•
•
Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
A
This appliance must be installed in accordance with the
accompanying installation instructions.
Model RDW24I
Model RDW24S
Stainless steel
24” (61.0 cm)
Integrated
approximate
Shipping Weight
Front Panel Type
(A) Width
front panel2
Front
23 1/2” (59.7 cm)
B
117 lbs. (53 kg.)
7/8” (86.0 cm) to
/2 (92.7 cm)4
34 3/8” (87.4 cm) to
36 1/2” (92.7 cm)
(B) Height
(C) De
8.1 cm)5
22 7/8” (58.1 cm)
ith
uration
Epicure®: 2 1/2” (6.4 cm)1
Millennia®: 2” (5.1 cm)2
(D) H
1 EHCH (chrome) or ADWE24HB (glossy black)
M24H (polished) or ARDWMH24 (brushed)
es installation of either a Dacor glass panel kit
or dealer), or a customer provided, custom overlay
om overlay panel allows you to blend the exterior of
r into the overall kitchen décor. See page 2/3 for more
Depth with door open
49 3/4” (126.4 cm)
Depth with door closed
C
D Handle depth
ith required trim kit installed.
ut custom front panel installed.
Drain hose
Do not modify
loop in hose
nit
Side
Drain hose
54” (137.0 cm)
long
Back
6 1/4” (15.9 cm) to
8 1/4” (21.0 cm)
Water supply line
60” (152.0 cm)
long
Power cord
44” (112.0 cm)
long
1 15/16” (4.9 cm)
3 3/8” (8.6 cm)
2 7/8” (7.3 cm)
UtILIty CoNNECtIoN DImENSIoNS
B
B
C
A
C
A
A = 7/8" (2.2 cm) B = 18 1/2" (47.0 cm) C = 2 3/8" (6.0 cm)
A = 1 3/8" (3.5 cm) B = 23" (58.40 cm) C = 2" (5.1 cm)
mILLENNIA StyLE hANDLE DImENSIoNS
(PARt NUmBERS ADWm24h AND ARDWmh24)
EPICURE StyLE hANDLE DImENSIoNS
(PARt NUmBERS ADWE24hCh AND ADWE24hCh)
All specifications subject to change without notice.
Phone: (800) 793-0093
RDW24I, RDW24S
Document # PG10-007
Revised 03/12/12 Page 3/3
PLANNING
GUIDE
Renaissance 24” Wide
Built-In Dishwasher
Drain Specifications
Custom Panel/Handle for Model RDW24I
IMPORTanT: Should a drain hose longer than the one provided be
required, use a hose extension approved for detergents and high
temperature water. Total drain hose length (including factory installed
hose) must not exceed 10 feet. (304.8 cm) from the top of the drain loop
on the back of the unit. Joints and joint tubes must have a minimum inside
diameter of 7/8” (2.2 cm).
■
The custom panel mounting screws are provided with the dishwasher.
Follow the panel dimensions below to ensure that the custom overlay
panel will fit properly.
■
The handle and handle mounting hardware are not included with
model RDW24I. A handle designed for use with an appliance should
produce satisfactory results. Do not use a knob or handle attached
by a single fastener. Instead use a handle with a larger D-style
pull. The panel craftsman must determine and obtain the proper
handle fasteners for the application. Handle screw heads must be
countersunk into the panel before panel installation.
■
The drain hose supplied with the dishwasher must be connected to
a minimum 1/2” inside diameter drain connection. The drain hose is
equipped with a cone-shaped connector on the end that is ready to be
cut to the desired drain connection size. Only a clamp (not provided)
is required. It fits drain connections with an internal diameter of 1/2,
5/8, 3/4 and 7/8 inches (1.3, 1.6, 1.8 and 2.2 cm).
(g) Height
(H) Width
(J) Thickness
30 1/8” (76.5 cm)
23 3/4” (60.3 cm)*
3/4” (1.9 cm) min.
■
You must install an air gap in the drain system if required by local
codes. Plan for the air gap in the sink or countertop area adjacent to
the dishwasher. A section of drain hose (not provided) needs to be
installed from the air gap to the waste disposer inlet or waste tee. See
below.
* Based on 24” (61de cutout. Recommended panel width is 1/4”
(6.4 mm) less th.
IMPORTanghs more than 15 pounds, you must
order the rings (Dacor PN 701385). Maximum
panel wgs: 23 pounds.
■
■
If an air gap is not required, the drain hose must be installed to a
disposer inlet or waste tee above the sink trap in the household
plumbing.
For proper drainage, the drain line connection must be a minimum
of 20” (50.8 cm) above the bottom of the dishwasher. No part of the
drain hose can be lower than the disposer or waste tee connection
higher than 35” (88.9 cm) from the bottom of the dishwasher.
G
CUStom PANEL
DImENSIoNS
ax.
20"
min.
H
J
ExAmPLE oF DRAIN CoNNECtIoN WIthoUt AIR GAP
35"
max.
20"
min.
ExAmPLE oF DRAIN CoNNECtIoN WIth AIR GAP
All specifications subject to change without notice.
Phone: (800) 793-0093
|