DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
Document # PG02-002
Revised 01/18/12 Page 1/3
PLANNING
GUIDE
24”, 27”, 30”, 36” Wide
Warming Drawers
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
Minimum Ambient
Operating Temperature
Electrical Circuit Required Total Connected Load
DWD ERWD EWD
120 Vac, 60 Hz, 15 Amp.
grounded, dedicated circuit
4.0 Amp. @
120 Vac, 60 Hz.
32°F (0°C)
3 1/2”
(8.9 cm)
3 7/16”
(8.7 cm)
1”
(2.5 cm)
1 1/8”
(2.9 cm)
1”
10 1/8”
(25.7 cm)
(2.5 cm)
MWDH, MWDV,
RWDV
3 1/4”
MRWD30B
(only)
All other MRWD
series
1 7/16”
(3.7 cm)
1”
(8.3 cm)
A
(2.5 cm)
1”
(2.5 cm)
DRsIONs
n)
HANDLE DIMENsIONs - sIDE VIEW
40” (101.6 cm)
3-prong 120 Vac
power cord
Mounting
hole 9 places
9"
(22.9 cm)
1/2" (1.3 cm)
B
C
Chassis without
drawer inserted
1/2" (1.3 cm)
)
Chassis
cHAssIs DIMENsIONs
(A) Drawer Face
Width
(B) Chassis Face
(C) Chassis
Width
Model
Width
DWD30
30” (76.2 cm)
27” (68.6 cm)
30” (76.2 cm)
24” (61.0 cm)
27” (68.6 cm)
30” (76.2 cm)
36” (91.4 cm)
26 3/4” (67.9 cm)
29 3/4” (75.6 cm)
27” (68.6 cm)
30” (76.2 cm)
27” (68.6 cm)
30” (76.2 cm)
30” (76.2 cm)
29 5/8” (75.2 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
23 5/8” (60.0 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
35 5/8” (90.5 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
29 5/8” (75.2 cm)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
22 1/4” (56.5 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
34 1/4” (87.0 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
28 1/4” (71.8 cm)
ERWD27
ERWD30
EWD24
5/64"
(2 mm)
EWD27
23 13/16”
(60.5 cm)
EWD30
Drawer open
EWD36
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
RWDV30
OVERALL DIMENsIONs - TOP VIEW
(EWD sERIEs sHOWN)
WARMING DRAWER OVERALL DIMENsIONs
All specifications subject to change without notice.
Phone: (800) 793-0093
DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
Document # PG02-002
Revised 01/18/12 Page 3/3
PLANNING
GUIDE
24”, 27”, 30”, 36” Wide
Warming Drawers
Cabinet/countertop tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
WARninG
Observe all governing codes and ordinances
during planning and installation. Contact your
local building department for further information.
•
•
3/4" min.*
(1.9 cm)
Warming
drawer
C
C
36" typ.
(91.4 cm)
This appliance must be installed in accordance
with the accompanying installation instructions.
D
120 Vac
electrical
outlet
Warming
drawer
3/4" min.*
(1.9 cm)
Mounting platform must be 3/4" (1.9 cm) thick
and support 100 lbs.
A
B
1 1/2" (3.8 cm)
Typical countertop
Cooktop
27"/30"/36" Dacor
single wall oven
3/4” min.*
(1.9 cm)
Warming
drawer
D
C
D
C
C
Warming
drawer
120 Vac
elect.
36" typ.
(91.4 cm)
120 Vac
electrical
outlet
Warming
drawer
120 Vac
elect.
A
B
Toe kick
3/4" min.*
(1.9 cm)
A
(B) Mi
Ad
(D) Min. Vertical Gap
Between Cutouts
Model
DWD30
(A) Cutout Width
ut Height
Min. Cutout Depth
28 1/2” (72.4 cm)
25 1/2” (64.8 c
28 1/2” (72.
22 1/2” (
25 1/
2
34
22 1/2”
25 1/2” (6
28 1/2” (72.4 )
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
m)*
2 cm)*
76.8 cm)*
4” (92.1 cm)*
**
1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
ERWD27
ERWD30
EWD24
EWD27
EWD30
EWD36****
IWD24
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
24” (61.0 cm)
IWD27
**
IWD30
**
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
OWD24*****
RWDV30
27” (68.6 cm)*
30” (76.2 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
27 1/4” (69.2 cm)*
30 1/4” (76.8 cm)*
22 5/8” (57.5 cm) 24 1/4” (61.6 cm)*** 11 15/16” (30.3 cm)
28 1/2” (72.4 cm) 30 1/4” (76.8 cm)* 9 1/8” (23.2 cm)
20 1/8” (51.1 cm)
24” (61.0 cm)
1 1/4” (3.2 cm)*
* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout.
The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout
dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the
custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below
cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
**** Model EWD36 cannot be installed above or below another warming drawer (any type).
***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type).
All specifications subject to change without notice.
Phone: (800) 793-0093
|